Start Here and Warranty

ManualsBrandsEpson ManualsPrintersEpson Epson PowerLite Pro Cinema LS10000

Quick Setup

Before using the projector, make sure you read the safety instructions in the

online User’s Guide (see the ”Where to get help” section).

Choose a location

Keep the projector level and place it at a

height so its lens is even with the top or

bottom of the screen and is centered

horizontally. If this isn’t possible, use the

lens shift feature or the keystone correction

button on the projector to reposition the

image (see “Adjust the image”).

To view 3D images correctly, RF 3D glasses

must be worn within 32 feet (10 m) of the

projector. Use the image to determine the

viewing distance for 3D projection (the

shading represents the 3D viewing area):

See the online User’s Guide for more information on where to place your

projector.

Connect the projector

Choose from the following connections. For additional connection types, see

the online User’s Guide.

Video device

Loosen the two screws at the bottom of the cable cover, then pull the

cover forward.

Lift the cable cover out of the grooves at the top.

Connect up to 4 video devices and use the Source buttons on the remote

control or the button on the projector to switch between them.

Component video cable

RCA video cable

HDMI cable

Turn on your equipment

Turn on your video source.

Plug in the projector.

Press the power button on the projector or the On button on the

remote control. The shutter opens and the power light flashes blue,

then stays on.

Note: To shut down the projector, press the power button on the

projector or the Standby button on the remote control.

The default language of the menu system is English. To select another

language, press the Menu button on the projector or remote control.

Select Settings and press Enter. Select Language and press Enter. Select

your language and press Enter. Press the Menu button to exit the menu

system.

Using the remote control

Make sure the batteries are installed as shown (two AA batteries).

Choose which source

to display

Turn projector on

Access projector

menus

Change the

3D format

Adjust zoom, focus

and lens shift

Turn off projector

display

Navigate projector

menus

Display test pattern

Turn projector off

Switch between

2D and 3D

Control connected

sources with

HDMI Link

For more information on using the remote control, see the online

User’s Guide.

Adjust the image

Press the Pattern button on the remote control to display a test pattern.

To raise the image or correct a tilted image, adjust the front feet as

shown below.

Press the Lens button on the remote control and use the and buttons

to focus the image.

Press the Lens button on the remote control again and use the and

buttons to reduce or enlarge the image.

Press the Lens button on the remote control again and use the , ,

and buttons to reposition the image.

If your image looks like or , you can use the button on the

projector to correct this.

Note: Using the keystone adjustment can affect the size and effective

resolution of your image. If possible, change the position of your

projector to eliminate the keystone effect and use the lens shift option to

position the image as necessary.

Viewing 3D images

To view 3D content, you must first connect a 3D-compatible video device to

one of the HDMI ports on your projector.

Turn on and begin playback on the 3D-compatible video device.

Note: Make sure you set the video device to play content in 3D mode.

Press the 2D/3D button on the remote control, if necessary.

Slide the power switch on your 3D glasses to the On position.

Note: If the glasses don’t automatically display 3D content, you may

need to pair them with the projector. Move the glasses within 10 feet

(3 m) of the projector, then press and hold the Pairing button on the

3D glasses for at least 3 seconds. The status light on the glasses will

alternately flash green and red, then remain green for 10 seconds if

pairing is successful.

You can also automatically convert 2D HDMI content to 3D. To enable the

2D-to-3D Conversion option, press the Menu button on the projector or

remote control. Select Signal and press Enter, then select 3D Setup and

press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak,

Medium, or Strong setting, then press Enter.

See the online User’s Guide for more information on adjusting 3D images.

Troubleshooting

If you see a blank screen or the No signal message after turning on your

video device or computer, check the following:

•

Make sure the power light on the projector is blue and not flashing.

•

Press the button on the projector or one of the Source buttons on

the remote control to switch to the correct image source, if necessary.

•

If you’re using a Windows

laptop, press the function key on your

keyboard that lets you display on an external monitor. It may be labeled

CRT/LCD or have an icon such as . You may have to hold down the

Fn key while pressing it (such as Fn + F7). Wait a moment for the display

to appear.

•

If you’re using a Mac laptop, open System Preferences and select

Displays. Click the Arrangement tab and select the Mirror Displays

checkbox.

If 3D images aren’t displaying properly, check the following:

•

Press the 2D/3D button to switch to 3D viewing mode, if necessary.

•

Make sure that you are within the 3D viewing range. See “Choose a

location” on the front of this sheet or the online User’s Guide for more

information.

PowerLite

Pro Cinema LS10000

4126297 Rev.0

1-F C

4126297 Rev.0

1-F M

4126297 Rev.0

1-F Y

4126297 Rev.0

1-F K

Summary of content (4 pages)

PAGE 1
PowerLite® Pro Cinema LS10000 Quick Setup Before using the projector, make sure you read the safety instructions in the online User’s Guide (see the ”Where to get help” section). Turn on your equipment Adjust the image Viewing 3D images 1 Turn on your video source. 1 Press the Pattern button on the remote control to display a test pattern. 2 To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. Plug in the projector.
PAGE 2
PowerLite® Pro Cinema LS10000 Quick Setup Before using the projector, make sure you read the safety instructions in the online User’s Guide (see the ”Where to get help” section). Turn on your equipment Adjust the image Viewing 3D images 1 Turn on your video source. 1 Press the Pattern button on the remote control to display a test pattern. 2 To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. Plug in the projector.
PAGE 3
• Check that your 3D glasses are charged and have not entered standby mode. Slide the power switch on the 3D glasses to the Off position, then back to the On position. • Press the Menu button on your remote control, select the Signal menu, select 3D Setup, and then select 3D Format. Make sure that the Auto option is selected. • Check that your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information.
PAGE 4
• Check that your 3D glasses are charged and have not entered standby mode. Slide the power switch on the 3D glasses to the Off position, then back to the On position. • Press the Menu button on your remote control, select the Signal menu, select 3D Setup, and then select 3D Format. Make sure that the Auto option is selected. • Check that your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information.