User's Manual

ManualsBrandsEpson ManualsPrinter AccessoriesEpson Epson Printer Accessories R2400

CIS for Epson Stylus Photo R2400

Thank you for purchasing ST Continuous Ink Supply System. We appreciate

your support and will try our best to make your experience with our products a

pleasant one. Printing has been a different experience ever since you installed

ST Continuous Ink Supply system on your own printer. Just imagining being

able to print without regard to the ink level in those expensive little cartridges.

Please take your time installing ST Continuous Ink Supply system. Do not

remove your old cartridge until you have the ST CIS system primed and ready to

install (to prevent the drying of heads). In addition, make sure you are getting

perfect nozzle checks before installing the ST CIS system. The ST CIS system

won’t be able to work properly if the nozzles are previously clogged.

Most people get a perfect nozzle check the first time after installing the ST

Continuous Ink Supply system; others may need to run two or three cleaning

cycles or let the printer sit for a while before they get the perfect results.

1、General Guide:

1) Components

A、CIS system 1 set B、 Air filters 8pcs C、Support Arm 1 set

D、Refill Kit 8pcs E、Instruction CD 1pc

2) Opening box inspection

a、Check whether all the accessories are ready.

b、Check whether there's leakage of CIS System, whether some tubes have been

separated from CISS. If there is, please kindly to contact the local dealer.

C、Check whether there is air space in the tube. If the length of air space is more than

20cm, please clean the printer head for 2 or 3 times before printing.

2、Printer testing:

1) Check whether the printer is in normal condition, like mechanical status, lubrication

status etc.

2) Print testing lines to ensure the printing head is good condition.

3) Print pictures to see whether the printing image is ok.

Summary of content (7 pages)

PAGE 1
CIS for Epson Stylus Photo R2400 Thank you for purchasing ST Continuous Ink Supply System. We appreciate your support and will try our best to make your experience with our products a pleasant one. Printing has been a different experience ever since you installed ST Continuous Ink Supply system on your own printer. Just imagining being able to print without regard to the ink level in those expensive little cartridges. Please take your time installing ST Continuous Ink Supply system.
PAGE 2
3、Installation Procedures: 1) First step Put the CISS on the left side of the printer. In the meantime place all the tubes at correct position. Pull out the small rubber plug from the air hole as above picture shown. Place 8pcs of air filters into air holes, the thicker side is down into tank. 2) Second step: Remove out the original cartridges Press the ink cartridge replace button to make the small cart move to the position which ready to change the ink cartridges. And draw out the electrical Source.
PAGE 3
Remove out the original cartridges ,then place down each cartridge according to the color ,in the meantime, make every cartridge in the correct position. Remove the cartridge cart back and place the cartridges down as show in picture ,then click the cartridges to the right position.
PAGE 4
Clip the tubes in the clip Now finished 7) Adjust the tubes Adjust the tube length and move the cartridge car. Insure there will no block and collision when the tubes moving with cartridge car .Insure there's plenty length of tube to make the cartridge cart can thoroughly move to the left side. The tube is excessive long, it The tube is twist ,it is not ok. is not ok.
PAGE 5
OK Everything is in normal You can work your print Show breaks If it show this breaks, please clean the printing head Enter this item If there show breaks, please clean your printing head. It is possible that the wispy air have entered into the printing head. If it is still show little breaks specially show in one color, it no need to repeatedly continue to clean. Just keep the printer silent for about one hour, it may disappear.
PAGE 6
First place the left side of cartridge cover down correctly, second, put the other side of the cartridge cover at the above of the cart and adjust the position of the connection Then press the right side of the cartridge cover to make it down to the suitable position, now it is ok to work. 7、Attention for maintenance: Take out the CISS including the inner cartridges and other components. Then remove support arm from printer, and place the original cartridges in.
PAGE 7