Pro Cinema 4050 User's Guide
Contents Pro Cinema 4050 User's Guide................................................................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents...............................................
Using the Projector on a Network ............................................................................................................ Wired Network Projection................................................................................................................... Connecting to a Wired Network ..................................................................................................... Selecting Wired Network Settings .................................................................
Projection Modes ............................................................................................................................... Changing the Projection Mode Using the Menus........................................................................... Image Aspect Ratio ............................................................................................................................ Changing the Image Aspect Ratio .......................................................................
Projector Feature Settings - Settings Menu...................................................................................... Projector Setup Settings - Extended Menu....................................................................................... Projector Network Settings - Network Menu..................................................................................... Projector Information Display - Info Menu ......................................................................................
Solutions When a 3D Image Does Not Display Correctly ............................................................ Solving Projector or Remote Control Operation Problems ............................................................... Solutions to Projector Power or Shut-Off Problems ..................................................................... Solutions to Problems with the Remote Control........................................................................... Solutions to Panel Alignment Problems.
Pro Cinema 4050 User's Guide Welcome to the Pro Cinema 4050 User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• Powered zoom and focus adjustments Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
• Replacement lamp • Cable cover The product box contents may vary by country. Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options.
Parent topic: Projector Features Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • epson.
Projector software Manual Description Epson iProjection (Windows/Mac) Epson iProjection Operation Guide (Windows/Mac) Lets you project the computer screens of users over a network. Instructions are included with the app Lets you project from an iOS or Android device if your projector is connected to a network that includes a wireless access point. Epson iProjection app You can download the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or epson.
Projector Parts - Front/Top 1 Lamp cover 2 Exhaust vent 3 Lens shutter 4 Lens 5 Air intake/air filter cover 6 Remote receivers 7 Control panel Parent topic: Projector Part Locations 16
Projector Parts - Rear 1 Security slot 2 AC input port 3 Remote receiver 4 Opt.HDMI (300mA) port (USB power for optical HDMI connections) 5 HDMI1 (HDCP 2.
Projector Parts - Base 1 Mounting bracket holes (M4x9) 2 Rear foot 3 Cable cover screw holes 4 Front adjustable feet Parent topic: Projector Part Locations 18
Projector Parts - Control Panel 1 Status light 2 Lamp light 3 Temp light 4 Menu button (accesses projector menu system) 5 Enter button (selects options) 6 Control panel cover 7 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 8 Arrow buttons 9 Esc button (cancels/exits functions) 10 Lens button (cycles through lens adjustment options) 11 Source button (cycles through the list of sources) 19
12 Power button/light Parent topic: Projector Part Locations Projector Parts - Remote Control 1 On button (turns on projector) 2 Home button (displays Home screen) 20
3 Source buttons (select specific video input sources) 4 Link Menu button (displays the main menu of the connected device) Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) 5 HDMI Link button (displays the settings menu for HDMI Link) 6 Lens button (cycles through lens adjustment options) 7 Arrow buttons (move though on-screen options) 8 Default button (returns selected setting to default value) 9 Menu button (accesses projector menu s
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Front Rear Front Ceiling 23
Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If the projector cannot be centered in front of the screen, use lens shift to reposition the image instead of using keystone correction for better image quality. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
You can also use the projector Throw Distance Calculator at epson.com/support (U.S.) or epson.ca/support (Canada). 16:9 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Offset from lens center (3) Horizontal offset from lens center 11.3 inches (29 cm) 35.9 inches (91 cm) ±20.5 inches (52 cm) 13.6 inches (35 cm) 43 inches (109 cm) ±24.6 inches (63 cm) 18.2 inches (46 cm) 57.4 inches (146 cm) ±32.8 inches (83 cm) 22.7 inches (58 cm) 71.
Screen or image size Projection distance (1) Offset from lens center (2) Offset from lens center (3) Horizontal offset from lens center 56.7 inches (144 cm) 179.3 inches (455 cm) ±102.6 inches (261 cm) 68.1 inches (173 cm) 215.2 inches (547 cm) ±123.1 inches (313 cm) Offset from lens center (2) Offset from lens center (3) Horizontal offset from lens center 13.9 inches (35 cm) 43.9 inches (111 cm) ±25.1 inches (56 cm) 16.7 inches (42 cm) 52.7 inches (134 cm) ±30.1 inches (77 cm) 22.
Screen or image size Projection distance (1) Offset from lens center (2) Offset from lens center (3) Horizontal offset from lens center 68 inches (173 cm) 214.8 inches (546 cm) ±123 inches (312 cm) Wide to Tele 244.8 inches (622 cm) 357 to 746 inches (906 to 1896 cm) Parent topic: Projector Placement Projector Connections See these sections to connect the projector to a variety of projection sources.
Note: When an audio/video source that meets the HDMI CEC standard is connected to the projector's HDMI port, you can use the projector's remote control to control certain features of the linked device by pressing the HDMI Link button on the remote control and setting HDMI Link to On. Parent topic: Projector Connections Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector.
Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you to connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies, and more. Contact your device manufacturer for compatible adapter options. 1.
Connecting to External Speakers To add sound, you can connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI connection provides the best image quality, if available). You can also connect speakers to any video source that has its own speaker connections.
2. Connect the other end to the projector's Trigger Out port. 3. Turn on the Trigger Out setting in the projector's Extended menu. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Note: Epson iProjection is not recommended for use with streaming video. Wired Network Projection Wireless Network Projection Selecting External Network Detection Settings Wired Network Projection You can project through a wired network. To do this, you connect the projector to your network with an Ethernet cable, and then set up your projector and computer for network projection.
2. Connect the other end of the cable to the projector's LAN port. Parent topic: Wired Network Projection Selecting Wired Network Settings Before you can project from computers, tablets, or smartphones over your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4.
5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen on a smartphone or tablet.
7. Select the Wired LAN menu and press Enter. 8. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting. • If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter. Press Finish when you are done. 9.
After connecting and setting up the projector, install the projector software. You may need to install it from a software CD, if included, or download the software and manuals as necessary. Note: Wireless network connectivity is not recommended for video streaming. Note: If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly through the access point using the Epson network software.
The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network. Parent topic: Wireless Network Projection Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4.
6. Select the Basic menu and press Enter. 7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen on a smartphone or tablet.
8. Select the Wireless LAN menu and press Enter. 9. Select the settings on the Wireless LAN menu as necessary for your network. 10. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. After you complete the wireless settings for your projector, you need to select the wireless network on your computer, or iOS or Android device.
Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you quickly connect to local devices without an internet connection Advanced: lets you connect to multiple computers via a wireless network access point (infrastructure mode) Channel 1ch In Quick connection mode, selects the frequency band (channel) used by the wireless LAN 6ch 11ch SSID Up 32 alphanumeric characters Sets the SSID (network name) of the wirele
Parent topic: Selecting Wireless Network Settings Manually Related references Restricted IP Addresses Restricted IP Addresses When manually entering IP Settings, you cannot use these ranges of IP addresses: Setting Restricted IP addresses IP Address 0.0.0.0 127.x.x.x 224.0.0.0 to 255.255.255.255 Subnet Mask 0.0.0.0 255.255.255.255 Gateway Address 0.0.0.0 127.x.x.x 224.0.0.0 to 255.255.255.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus.
7. Do one of the following: • Press the LAN button on the remote control. • Select Display the QR Code in the projector's Network menu. • Press the Home button on the remote control and select Display the QR Code on the Home screen. Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8. Start Epson iProjection on your mobile device. 9.
4. Select Network Configuration and press Enter. 5. Select the Wireless LAN menu and press Enter. 6. Select Advanced as the Connection Mode setting and press Enter. 7. Select Search Access Point and press Enter. 8. Select the name of the wireless network you want to connect to and press Enter. 9. If the network has security enabled, enter the wireless password.
10. Select the settings on the Security menu as necessary for your network. 11. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Parent topic: Wireless Network Projection Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Security menu and press Enter. 6. Select the settings on the Security menu as necessary for your network. 7. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Passphrase — For the selected security, selects the pre-shared passphrase used on the network Parent topic: Enabling WPA or WPA2 Security Selecting External Network Detection Settings If you are using a compatible network control system, you can select settings that allow your projector to be detected by those systems. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4.
Parent topic: Using the Projector on a Network 49
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's power light turns blue. This indicates that the projector is receiving power. 3. Press the power button on the projector or the On button on the remote control to turn on the projector. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children.
2. Press the arrow buttons on the remote control or control panel to navigate the screen, and press Enter to select an option. 1 Select the video source you want to project 2 Display the QR code 3 Display the projector's menus 4 Select customizable menu options 5 Select to change the 3D settings 6 Select to change the Color Mode Note: You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3.
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Note: When using the Blank feature, the projector lamp is still on. To turn off the lamp, turn off the projector.
3. To transport or store the projector, make sure the Status light is off, then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status light is on or flashing. Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Related tasks Shutting Off the Picture Temporarily Transporting the Projector Viewing 3D Images You can view 3D images using your projector.
2. Turn on the video device, then turn on the projector. 3. Begin playback from the video device. Note: Make sure you set the video device to play content in 3D mode. 4. Slide the power switch on the 3D glasses to the On position. 5. Put on the 3D glasses and view the projected image. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the status light flashes green.
2. Set the image source on the projector to HDMI. 3. Project a 3D image. 4. Slide the power switch on the 3D glasses to the On position. 5. Move the glasses within 10 feet (3 m) of the projector and hold down the Pairing button for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off.
1. Connect the smaller end of the charging cable to the port on the bridge of the glasses. Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable. 2. Do one of the following: • Plug the other end of the charging cable into a powered USB port on a computer or other device. • Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications: Input: 100-240V, ~0.
3D Viewing Range When you view 3D images, make sure you are positioned within the viewing range shown here. 1 32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
3. To adjust the position of the projected image further, press the Lens button on the remote control or projector until Adjust Lens Shift appears on the screen. If the projected image is unevenly rectangular, you need to adjust the image shape.
4. Press the arrow buttons on the remote control or the control panel to adjust the position of the projected image as necessary. 1 Maximum horizontal range (H × 47%) 2 Maximum vertical range (V × 96%) 3 1/2 the vertical height of the image 4 1/2 the horizontal width of the image Note: You cannot move the image to both the horizontal and vertical maximum values. 5. When you are finished, press the Esc button on the control panel or remote control.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
1. Turn on the projector and display an image. 2. Press the Lens button on the control panel or remote control. 3. Press the Lens button repeatedly until Adjust Zoom is displayed on the screen. 4. Press and hold the left or right arrow button on the control panel or remote control to resize the image. 5. Press the Esc button on the control panel or remote control when finished.
Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
4 10° 1 32 feet (10 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
• Press the Home button on the remote control and select your image source. Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.
1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Related concepts Projector Placement Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios.
Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. Note: For HDMI sources, the input signal determines the image's aspect ratio. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. A list of the available aspect ratios appears. 3. To cycle through the available aspect ratios for your input signal, press the up or down arrow button. 4. Press Enter to select the aspect ratio.
Aspect ratio setting Description Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Note: When projecting a 4K signal, you can select only Normal as the aspect ratio setting. Parent topic: Image Aspect Ratio Color Mode The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types.
4. To cycle through all the available Color Modes for your input signal, press the up or down arrow button. 5. Press Enter to select a Color Mode.
3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
2. Press the P-in-P button on the remote control. The second HDMI video source appears as a sub-screen in the corner of the image. Note: Press the Menu button on the remote control to adjust picture-in-picture options. 3. To swap the main screen and sub-screen video sources, press and hold the P-in-P button for at least three seconds. 4. Press the P-in-P button again to exit.
Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Lens lock to prevent changing the zoom, focus, or lens shift settings. • Button lock security to block operation of the projector using the buttons on the control panel. • Security cabling to physically cable the projector in place.
4. Select one of these lock types and press Enter: • To lock the zoom, focus, and lens shift settings, select Lens Lock. • To lock the projector's power button, select Child Lock. To turn the projector on, you must press the power button for longer than three seconds. Note: Child Lock does not prevent the projector from turning on when the power cord is connected if the Direct Power On Setting is set to On. • To lock all buttons, select Control Panel Lock > Full Lock.
Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information. Parent topic: Projector Security Features Using Advanced Image Adjustment Features Follow the instructions in these sections to use your projector's advanced image adjustments. Note: Not all adjustments may be available depending on the projection mode and input signal.
Note: This feature may not be available depending on the projection mode and input signal. 1. Press the Frame Int button. You see a screen like this: 2. Select the level of interpolation and press Enter. 3. When you are finished, press the Frame button. Note: If your resulting images contain noise, turn off the Frame Interpolation setting.
Note: This feature may not be available depending on the projection mode and input signal. 1. Press the Menu button on the remote. You see a screen like this: 2. Select the Image Enhancement setting and press Enter. You see a screen like this: 3. Select the 4K Enhancement setting and press Enter.
4. Select one of the following options and press Enter: • Off to disable 4K enhancement • On to enable 4K enhancement 5. Press Menu to exit the menus. Parent topic: Using Advanced Image Adjustment Features Related references Image Adjustment Restrictions Creating Image Presets You can quickly optimize your projected image by selecting image adjustment settings and saving them as a preset you can reuse later.
2. Select the Image Enhancement setting and press Enter. 3. Select the Image Preset Mode setting and press Enter. 4. Select one of the presets and press Enter. Note: If you select a previously used preset, your new adjustments overwrite the old ones. 5. Press Esc to return to the Image Enhancement menu. 6. Fine-tune the following settings: • Noise Reduction • MPEG Noise Reduction • Super-resolution • Detail Enhancement 7. Press Menu or Esc to exit the menus.
You see a screen like this: 2. Select the Image Enhancement setting and press Enter. 3. Select the MPEG Noise Reduction setting and press Enter. 4. Select the level of noise reduction and press Enter. 5. Press Menu or Esc to exit the menus.
You see a screen like this: 3. Select the Image Enhancement setting and press Enter. 4. Select the Super-resolution setting and press Enter. 5. Adjust each of the following options as necessary: • Fine Line Adjust to enhance fine details such as hair and fabric patterns • Soft Focus Detail to enhance the outline, background, and main parts of an image Note: Higher values increase the intensity of the effect. 6. Press Menu or Esc to exit the menus.
2. Press the Menu button. You see a screen like this: 3. Select the Image Enhancement setting and press Enter. 4. Select the Detail Enhancement setting and press Enter. 5. Adjust each of the following options as necessary: • Strength to adjust the image contrast • Range to adjust the enhanced area of the image Note: Higher values increase the intensity of the effect. 6. Press Menu or Esc to exit the menus.
Fine mode Fast mode (Image Processing) (Image Processing) 2K 2K Input type 2D-to-3D 4K input 3D 2K 2D or 2K 3D 4K Projection Mode 2K 4K Enh. 2K 4K Enh.
Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature. For best results, project an image sized at least 60 inches (152 cm) diagonally in a dark room and on a projection surface that is not colored or textured. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted. 1. Turn on the projector. 2. Press the Menu button. 3.
11. Select Start Adjustments and press Enter. You see this screen: 12. Press Enter. You see a screen like this: 13. Use the arrow buttons on the remote control to adjust the color alignment of the color you selected for the Select Color setting. 14. When you are finished adjusting the screen, press Enter.
You see this screen: Note: Your adjustments affect the gridlines in the entire screen. To fine-tune your adjustments, continue with the next steps. 15. Select Adjust the four corners and press Enter. (Otherwise, select Exit and press Enter.) 16. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box. 17. Press the Enter button to move to the next corner of the screen. 18.
You see this screen: 19. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any misaligned box on the screen and press Enter. Repeat this step as necessary.
2. Select the Extended menu and press Enter. 3. Select the Display setting and press Enter. 4. Select the Color Uniformity setting and press Enter. 5. Press Enter and select On. 6. Press Esc. 7. Select the Adjustment Level setting and press Enter. 8. Press the right and left arrow buttons to adjust the level, then press Esc. 9. Select the Start Adjustments setting and press Enter.
10. Select the area of the screen that you want to adjust and press Enter. Note: Adjust the outer areas first, then adjust the entire screen. 11. Select the color (Red, Green, or Blue) you want to adjust, and use the left arrow button to weaken the color tone and the right arrow button to strengthen the color tone. 12. Press Esc. 13. Repeat steps 10 and 11 for each area you want to adjust. 14. Repeat steps 7 to 11 for each adjustment level. 15. When you are finished, press the Menu button.
You see this screen: 5. Select one of the following options: • Load Memory: Overwrites your current settings with saved settings • Save Memory: Saves your current settings to memory (10 memories with different names are available) Note: A memory name that has already been used is indicated by a blue mark. Saving over a previously saved memory overwrites the settings with your current settings. • Erase Memory: Erases the selected memory settings • Rename Memory: Renames a saved memory 6. Press Esc to exit.
3. Press the Menu button. Note: You can also press the Memory button on the remote control to access the Memory menu directly. 4. Select the Settings menu and press Enter. 5. Select the Memory setting and press Enter. You see this screen: 6. Select one of the following options: • Load Lens Position: Overwrites your current focus, zoom, and lens shift settings with saved settings Note: You can load the saved settings from Memory1 or Memory2 by pressing the Lens1 or Lens2 buttons on the remote control.
• Rename Lens Position: Renames a saved lens position (12 characters maximum) 7. Press Esc to exit.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Note: The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Color Temp. (color temperature) Color Temp. Skin Tone Customized Description Color Temp.
Setting Options Description Image Enhancement 4K Enhancement 4K Enhancement: accepts 4K signals and enhances the output of 1080p signals Image Preset Mode Noise Reduction MPEG Noise Reduction Super-resolution Detail Enhancement Image Preset Mode: selects one of five preset groups of settings for the next image enhancement options Noise Reduction: reduces flickering in analog images MPEG Noise Reduction: reduces the noise or artifacts seen in MPEG video Super-resolution: sharpens blurred images result
Setting Options Description Advanced Gamma Selects various detailed color settings RGBCMY Deinterlacing EPSON Super White Gamma: adjusts the gamma levels of the image. Select Customized to adjust the gamma while viewing the image or a graph.
Setting Options Description Auto Iris Off Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Normal High Speed Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting. Parent topic: Adjusting the Menu Settings Related references Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically.
Setting Options Description 3D Setup 3D Display Selects various 3D options 3D Format 3D Display: enables 3D mode 2D-to-3D Conversion 3D Format: selects the 3D format 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 2D-to-3D Conversion: converts 2D images to 3D 3D Depth: sets the depth for the 3D image Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: revers
Setting Options Description Auto Setup On Automatically optimizes computer image quality Off Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Blanking Various settings Covers part of the image with a black screen to hide raster lines at the edge of the screen. Note: Using this feature reduces the image size.
Note: You can set the HDMI Video Range setting only when the Epson Super White setting is set to Off. The Reset setting does not reset the Diagonal Screen Size, 3D Viewing Notice, and Aspect settings. The Aspect setting is not available for HD video signals. Parent topic: Adjusting the Menu Settings Related concepts Image Aspect Ratio Related tasks Viewing 3D Images Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options HDMI Link Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports Power On Link Power Off Link Link Buffer HDMI Link: enables or disables the HDMI Link function Power On Link: controls what happens when you turn on the projector or a linked device • PJ -> Device or Bidirectional: turns on the linked device when the projector is turned on • Device -> PJ or Bidirectional: turns on the projector
Setting Options Description User Button Fine/Fast (Image Processing) Assigns a menu option to the User button on the remote control for onetouch access 3D Display 2D-to-3D Conversion Power Consumption Info Display the QR Code Memory Load Memory Save Memory Erase Memory Rename Memory Load Lens Position Save Lens Position Erase Lens Position Rename Lens Position Controls the saved projector settings and lens positions Load Memory: displays the list of customized settings entries that you have created
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Adjust settings on the Home Screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear/Ceiling Operation — See the Operation settings table in this topic Standby Mode Communication Off Indicates whether the projector can be monitored over a network while in standby mode Communication On Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Display settings
Setting Description Direct Power On Turns on the projector when you plug it in Sleep Mode Automatically places the projector in standby mode after an interval of inactivity Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep Mode must be turned on) Illumination Turns off the status indicator lights on the projector Trigger Out Outputs a DC 12V signal at 200 mA maximum from the 3.
Note: Some settings are only available if the optional wireless LAN module is installed. Setting Options Description Wireless LAN Power On Enable or disable wireless communication Off Net. Info - Wireless LAN Connection mode Wireless LAN Sys.
Setting Options Description Net.
Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Event ID code Cause and solution 0022 Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0027 0028 0029 0030 0031 0035 0434 0481 0482 0485 0432 Turn the projector off and then on again. 0435 0433 Cannot display the transferred images. Restart the network software. 0484 Communication with computer was disconnected. Restart the network software. 04FE The network software quit unexpectedly.
Event ID code Cause and solution 0020 Communication error. Turn the projector off and then on again. 0026 0032 0036 0037 0038 0899 Parent topic: Projector Information Display - Info Menu Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All Config option on the Reset menu.
You cannot reset the following settings using the Reset All Config option: • Language • Lamp Hours • Memory settings • All settings in the Network menu • Panel Alignment • Color Uniformity Parent topic: Adjusting the Menu Settings 115
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper. After cleaning, close the shutter. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Note: Unplug any charging cables from the glasses before cleaning them. Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Air Filter and Vent Maintenance Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.
• You see a message telling you to clean it. 1. Turn off the projector and unplug the power cord. 2. Press and hold the tab on the air filter cover, and pull to remove the cover. 3. Pull the air filter out of the projector.
4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas. 5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.
6. Place the air filter back in the projector as shown. 7. Attach the air filter cover as shown. Parent topic: Air Filter and Vent Maintenance Related tasks Replacing the Air Filter Replacing the Air Filter You need to replace the air filter in the following situations: • After cleaning the air filter, you see a message telling you to clean or replace it • The air filter is torn or damaged You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1.
2. Press and hold the tab on the air filter cover, and pull to remove the cover. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Attach the air filter cover as shown. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Parent topic: Projector Maintenance Related references Projector Information Display - Info Menu Projector Lamp Specifications Optional Equipment and Replacement Parts Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 6. Lift up the lamp handle and gently pull the lamp out of the projector.
Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Lower the handle. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws.
9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp's usage. Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Specifications Transporting the Projector The projector contains precision parts, some of which are glass.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image Problems Solving Projector or Remote Control Operation Problems Solutions When Wireless Authentication Fails Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp light Temp light Status and solution Blue Flashing blue Off Warming up; wait for an image to appear Off Shutting down; when the Status light stops flashing, you can unplug the projector Off Off Off Off Standby or sleep mode Blue Varies Off Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem Off • Check the Lamp Hours in the Info menu to see if the lamp is burned out.
Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Related tasks Cleaning the Air Filter Replacing the Lamp Replacing the Air Filter Solving Image Problems Check the solutions in these sections if you have any problems with projected images.
• Adjust the Brightness setting or select the Normal Power Consumption setting. • Check the Display setting to make sure Messages is set to On. • For images projected with Windows Media Center, reduce the screen size from full screen mode. • For images projected from applications using Windows DirectX, turn off DirectX functions. • If the other solutions do not solve the problem, reset all of the projector settings using the options on the Reset menu.
Related concepts Projector Connections Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1. Hold down the laptop's Fn key and press the key labeled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. To display on both the laptop's monitor and the projector, try pressing the same keys again.
• As a test, try setting the computer's display resolution to the lowest possible setting, and then gradually increase it as necessary. • Check the input resolution under Projector Info in the Info menu and make sure that the projector supports that resolution.
• If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape. • Adjust the image shape using the Keystone menu setting.
Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. • Check the lens for condensation. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it.
Solutions When the Image Brightness or Colors are Incorrect If the projected image is too dark or light, or the colors are incorrect, try the following solutions: • Press the Color Mode button on the remote control to try different color modes for the image and environment. • Check your video source settings. • Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Advanced, and Color Saturation.
• Make sure your 3D glasses are paired with the projector. • Adjust the 3D Depth setting on the Signal menu. • Make sure you are within the 3D viewing range. • To minimize 3D crosstalk, reduce the brightness of 3D images by selecting the following settings: • Color Mode: 3D Cinema • 3D Brightness: Low • 3D Depth: 0 • HDMI Video Range: Normal • Make sure your screen size matches the Diagonal Screen Size setting on the Signal menu. • Avoid using the projector near wireless networks, microwave ovens, 2.
Solutions to Panel Alignment Problems Solutions When Using HDMI Link Parent topic: Solving Problems Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet. • The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector.
Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries. • Make sure you are operating the remote control within the reception angle and range of the projector. • Make sure the projector is not warming up or shutting down.
Parent topic: Solving Projector or Remote Control Operation Problems Related references Projector Feature Settings - Settings Menu Related tasks Adjusting the Color Convergence (Panel Alignment) Focusing the Image with the Lens Button Solutions When Using HDMI Link If you cannot control an HDMI device using the HDMI Link buttons, try the following solutions: • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at epson.com/support (U.S.), epson.ca/support (Canada), or epson.com.jm/support (Caribbean) and select your product for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution 1920 × 1080 pixels (1080p) Lens F=2.
Projection distance 58.3 inches (1.48 m) to 747.6 inches (18.99 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:9 (width-to-height) Focus adjustment Powered Zoom adjustment Optical, powered Zoom ratio 1 to 2.1 (Tele-to-Wide) Noise level 31 dB (High Power Consumption mode) 20 dB (ECO Power Consumption mode) Keystone correction angle ± 30º vertical USB Type B port compatibility USB 1.1 and 2.
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications Reception range 32 feet (10 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 17.7 inches (450 mm) Width 20.5 inches (520 mm) Depth 6.
Power consumption Operating: (220 to 240 V) High Power Consumption mode: 355 W ECO Power Consumption mode: 271 W Standby: 0.
Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically. Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.
HDMI 3D Signals Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV (720p) 50/60 1280 × 720 Frame Packing Side by Side Top and Bottom HDTV (1080i) 50/60 1920 × 1080 Side by Side HDTV (1080p) 50/60 1920 × 1080 Side by Side 24 1920 × 1080 Frame Packing Side by Side Top and Bottom Compatible 4K HDR Signals Display format (refresh rate) Chroma subsampling (pixel encoding) Color depth: 24 bits (8-bits per pixel) Color depth: 30 bits (10-bits per pixel) Color depth: 3
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols FCC Compliance Statement Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue. • Do not store the projector outdoors for an extended length of time.
• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
List of Safety Symbols The following table lists the meaning of the safety symbols labeled on the equipment. Symbol Approved Standards Description IEC60417 "ON" (power) No.5007 To indicate connection to the mains. IEC60417 "OFF" (power) No.5008 To indicate disconnection from the mains. IEC60417 Stand-by No.5009 To identify the switch or switch position by means of which part of the equipment is switched on in order to bring it into the standby condition. ISO7000 Caution No.
Symbol Approved Standards Description IEC60417 Polarity of DC power connector No.5926 To identify the positive and negative connections (the polarity) on a piece of equipment to which a DC power supply may be connected. — Polarity of DC power connector To identify the positive and negative connections (the polarity) on a piece of equipment to which a DC. power supply may be connected. IEC60417 Battery, general No.5001B On battery powered equipment.
Symbol Approved Standards Description IEC60417 Alternating current No.5032 To indicate on the rating plate that the equipment is suitable for alternating current only; to identify relevant terminals. IEC60417 Direct current No.5031 To indicate on the rating plate that the equipment is suitable for direct current only; to identify relevant terminals. IEC60417 Class II equipment No.5172 To identify equipment meeting the safety requirements specified for Class II equipment according to IEC 61140.
Symbol Approved Standards Description ISO 3864 Disassembly prohibition To indicate a risk of injury, such as electric shock, if the equipment is disassembled. IEC60417 Standby, partial standby No. 5266 To indicate that part of the equipment is in the ready status. ISO3864 Caution, movable parts IEC60417 To indicate that you must keep away from movable parts according to protection standards. No.
a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
1.2 Binding Arbitration. You and Epson agree that all Disputes shall be resolved by binding arbitration according to this Agreement. ARBITRATION MEANS THAT YOU WAIVE YOUR RIGHT TO A JUDGE OR JURY IN A COURT PROCEEDING AND YOUR GROUNDS FOR APPEAL ARE LIMITED.
selection of the arbitrator. The arbitrator is bound by the terms of this Agreement. The arbitrator, and not any federal, state or local court or agency, shall have exclusive authority to resolve all disputes arising out of or relating to the interpretation, applicability, enforceability or formation of this Agreement, including any claim that all or any part of this Agreement is void or voidable.
agreed upon by you and Epson in writing, the arbitrator shall determine the amount of fees, costs, and expenses to be paid by Epson pursuant to this Section 1.6d). e) Attorney's Fees. Epson will not seek its attorney's fees and expenses for any arbitration commenced involving a Dispute under this Agreement. Your right to attorney's fees and expenses under Section 1.
Google® is a registered trademark and AndroidTM is a trademark of Google LLC. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices Copyright Notice All rights reserved.
certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law. Parent topic: Copyright Notice Copyright Attribution © 2018 Epson America, Inc.
