Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers.
Contents Welcome! 1 About Your Software 2 About Your Documentation 3 Using the EPSON Printer Information Center 4 Launching the Movies 4 Launching the Manual 5 Printing From Start to Finish 7 Loading Paper 8 Loading Envelopes 9 Basic Printing in Windows 10 Selecting the Settings You Use Most Often Basic Printing on a Macintosh 12 12 Printing with OS 8.5.1 to 9.
Maintaining Your Printer 27 Cleaning the Print Head 27 Running the Head Cleaning Utility 28 Examining the Nozzle Check Pattern 29 Replacing an Ink Cartridge iv 29 Checking the Ink Supply 29 Purchasing Ink Cartridges 30 Ink Cartridge Precautions 30 Removing and Installing Ink Cartridges 31 Aligning the Print Head 34 Cleaning the Printer 35 Transporting the Printer 36 Solving Problems 37 Printer Parts Diagnosing Printer Problems Running a Printer Check Problems and Solutions Setup a
Requirements and Notices 57 Windows System Requirements 57 Macintosh System Requirements ENERGY STAR Compliance 58 58 Important Safety Instructions 59 Ink Cartridge Safety Instructions 60 FCC Compliance Statement 61 Declaration of Conformity 62 Epson America, Inc.
Welcome! Your EPSON Stylus® C62 printer is ideal for personal or home office use. It provides you with these great features: ■ Exceptionally high print quality for printing anything from reports and resumes to family photos and greeting cards. ■ Resolution Performance Management™ (RPM) technology, which optimizes the number and placement of ink droplets on a variety of paper types, and delivers superior photo quality and performance with manageable print file sizes.
About Your Software The CD-ROM that came with your printer includes all the software you need for printing. (You must have a CD-ROM or DVD drive installed in your computer.) See the Start Here sheet for installation instructions. ■ Your printer driver runs your printer and lets you control how your documents look. You can’t print without it. Tip: It’s a good idea to check EPSON’s support web site periodically for free updates to your printer driver. Visit http://support.epson.com.
About Your Documentation To set up your printer and install its software, see the Start Here sheet. This book contains system requirements, important safety information, your warranty, and instructions on: ■ Using the EPSON Printer Information Center ■ Printing with Windows® or on a Macintosh® ■ Maintaining the printer ■ Solving basic problems Please follow these guidelines throughout: Warning: must be followed carefully to avoid bodily injury.
Using the EPSON Printer Information Center Need help loading paper, clearing a paper jam, or cleaning the print head? Use the EPSON Printer Information Center (EPIC) to view printer movies that quickly tell you how. EPIC also includes an on-screen Reference Guide with additional printer details. Follow the instructions on the Start Here sheet to install the EPSON Printer Information Center, if you haven’t already. Note: You need a browser—such as Microsoft® Internet Explorer 4.
3. Click the appropriate topic, then click the title of the movie you want to watch. Use the program tools to pause a movie, replay a step, or skip ahead. Click a topic, to view a movie 4. Click Exit to exit Print Show. Launching the Manual 1. Double-click the EPSON Printer Information Center icon on your desktop. 2. Click Reference Guide. You see this screen: Click here to expand the table of contents 3. Click a topic on the left to expand the table of contents.
4. Click on the topic you want to view. ■ Click right arrows ■ Click down arrows to view subtopics, then click on a topic. to close subtopic lists. Closed list, click to expand Click to go to topic Note: If you see an icon for a graphic when viewing your Reference Guide in Netscape Navigator, click the Reload button to load the graphic.
Printing From Start to Finish Follow the instructions in these sections to print using all your printer’s features: ■ “Loading Paper” on page 8 ■ “Basic Printing in Windows” on page 10 ■ “Basic Printing on a Macintosh” on page 12 ■ “Customizing Your Print Settings” on page 17 ■ “Selecting the Correct Media Type” on page 21 ■ “Using Film Factory” on page 22 ■ “Using Exif Print” on page 22 Tip: Whenever you print, make sure you: ■ Use the right paper.
Loading Paper 1. Press in the locking tab on the left edge guide and slide it to the approximate width of your paper. 2. Place paper in your printer on the right side of the sheet feeder, behind the tab. 3. Slide the left edge guide lightly against the paper. 4. Pull out the output tray extension.
Loading Envelopes 1. Load up to 10 envelopes, short edge first and printable side up. Tip: For best results, press each envelope flat before loading it, or load one envelope at a time. 2. Place the envelope’s flap edge against the right edge of the sheet feeder, behind the tab. 3. Press the locking tab on the left edge guide and slide it against the envelopes.
Basic Printing in Windows After you create a document in a software program, follow these steps to print it: 1. From the File menu, click Print. You see a Print window like this one: Select your printer here Click here to open your printer software 2. Make sure EPSON Stylus C62 Series is selected. 3. Click the Properties or Preferences button. (If you see a Setup, Printer, or Options button, click it. Then click Properties or Preferences on the next screen.
4. Select the following settings on the Main tab in your printer settings window. The most important thing to remember is to set the correct paper Type for the paper you’re using.
Selecting the Settings You Use Most Often Your printer settings apply only to the program you’re currently using. If you want, you can change the default Windows printer settings for all your programs. 1. Right-click the printer icon in the lower right corner of your screen (taskbar). 2. Select Printer Settings. You see the window shown on page 11. 3. Select the default settings you want for all your applications, then click OK. You can always change the settings in your program, if necessary.
3. From the File menu, select Print. Select the following settings: 1 Select your paper type (see page 21) 2 Select Color (for color documents and black and white photographs) or Black (for black text documents) 3 Select Automatic mode 4 Select Quality or Speed (for faster printing) Tip: For more information about printer settings, click the button. 4. You can also do the following: ■ Click to reduce/enlarge, print multi-page layouts, or add a watermark. ■ Click to turn on background printing.
Printing with OS X If you’re using an OS X compatible printing application, follow the steps below to print a document. (If you’re using an application that’s compatible only with Macintosh Classic mode, follow the steps on page 12 instead.) Before you begin, make sure you added your printer to Print Center as described in “Installing Printer Software on Mac OS X” on page 49. 1. From the File menu, select Page Setup. 2.
6. Select the following Print Settings as necessary: 1 Select your paper type (see page 21) 2 Select Color (for color documents and black and white photographs) or Black (for black text documents) 3 Select Automatic mode 4 Select Quality or Speed Tip: For more information about printer settings, click Help. The OS X printer driver contains a subset of the settings available with the OS 8.5.1 to 9.x Macintosh printer driver described in this book. 7.
9. To monitor the progress of your print job, click the Print Center icon when it appears in the dock on the bottom of your desktop. You see a screen like this: 10. Monitor the progress of your print job or do one of the following: ■ Click the print job, then click Delete to delete the job. ■ Click the print job then click Hold to pause printing. ■ Click a print job marked “Hold” and click Resume to resume printing.
Customizing Your Print Settings You can use advanced settings for color matching, printing at higher resolutions, or selecting a variety of special effects and layouts. Customizing Windows Print Settings 1. On the Main tab, click the Advanced button in the bottom right corner of the window. The Basic settings change to the Advanced settings. 2.
4. Select the following page layout settings as necessary: 1 Select image position options here 2 Select image resizing options here; these affect only your printed image 3 Add a watermark to your printed page here 4 Select multi-page document options here and here To print a large image on several sheets to make a poster, select poster settings here Note: For more information on page layout settings, click the Help or button. 5.
Customizing Macintosh Print Settings 1. On the printer settings window, click Custom, then click the Custom Settings list to open it. Macintosh OS 8.5.1 through 9.
4. Select these advanced settings as necessary: Macintosh OS 8.5.1 through 9.
Selecting the Correct Media Type Your printer automatically adjusts itself for the type of paper you select in your print settings. That’s why the Type or Media Type setting is so important. It tells your printer what kind of paper you’re using and adjusts the ink coverage accordingly. Here are the settings you should choose for your paper: For this paper . . . Select this Type or Media Type setting . . .
Using Film Factory You can use Film Factory to organize, retouch, and print your digital images. If your digital camera supports Exif (Exchangeable Image File) Print, you can use this technology when you print with Film Factory to ensure the most accurate image reproduction (not available with Macintosh OS X). Using Exif Print With Exif Print, special image settings such as white balance, contrast, color saturation, and exposure time are saved in your digital photo files.
Opening Your Photos in Film Factory 1. Start Film Factory. You see the main Film Factory screen: Click Roll to create a new roll, or . . . click an existing roll Note: If you need help with Film Factory, select it from the Help menu or check the on-screen Getting Started Guide that was installed with Film Factory (you must have Adobe® Acrobat® Reader® installed on your system to view the manual). 2. Select a “roll of film” or click the Roll button and select New Roll. 3.
5. To import a photo into Film Factory, click the Import button, then: ■ Click From File to import a photo from your computer’s hard drive. ■ Click From Removable Media to import a photo from a disk or CD-ROM. ■ Click From PC Card to import a photo from a PC card in a card reader. ■ Click From Twain Device to import a photo from a scanner or digital camera. If your device is already selected, the software will open.
Printing Your Photos 1. When you’re ready to print, click the Print Assignment button. You see this screen: Click to print the date with your photo Select your printer settings here 2. Windows and Macintosh OS 8.5.1 to 9.x: Select these options in the Printer Settings box at the bottom of the screen: 1 Make sure your printer is selected 2 Select your paper size 3 Select a Media Type Macintosh OS X: Click the Properties button.
4. Click the Print button on the left side of the screen. You see additional options: Select the number of copies you want to print Leave this box checked for the best printed output using Exif Print data, if available 5. If your photo doesn’t look right in the preview, click the Back button and change your settings. (Click the Detailed Preview button for a closer look.) 6. Select the number of copies you want to print. 7.
Maintaining Your Printer This chapter describes maintenance procedures to keep your printer working at its best, and preparation steps for moving your printer. ■ “Cleaning the Print Head” below ■ “Replacing an Ink Cartridge” on page 29 ■ “Aligning the Print Head” on page 34 ■ “Cleaning the Printer” on page 35 ■ “Transporting the Printer” on page 36 Cleaning the Print Head If your printouts are unexpectedly light, or dots or lines are missing from the image, you may need to clean the print head.
Running the Head Cleaning Utility 1. Make sure the printer is turned on but not printing, and the red b error light is off. (If the red light is flashing or on, you may need to replace the ink cartridge; see page 29 for details.) 2. Do one of the following: ■ Windows: Right-click the printer icon on your taskbar (in the lower right corner of your screen). Select Head Cleaning. ■ Macintosh: OS 8.5.1 to 9.x: Open the File menu and choose Page Setup or Print.
Examining the Nozzle Check Pattern Examine the nozzle check pattern you print. Each colored square should be solid, with no gaps or lines, as shown: ■ If your printout looks okay, you’re done. ■ If you see any white lines or gaps, clean the print head again; see page 28 for instructions. Replacing an Ink Cartridge When the red b light flashes, an ink cartridge is low on ink. (You may also see a message on your screen.) This is a good time to make sure you have a new cartridge.
Macintosh OS 8.5.1 to 9.x: Open the File menu and choose Print. Click the ink icon. Macintosh OS X: Choose Applications > EPSON Printer Utility > C62 Series > Status Monitor. You see a window like the one on the right: Click a cartridge image to display information about the cartridge.
Removing and Installing Ink Cartridges Be sure you have a new ink cartridge before you begin. Once you start replacing an ink cartridge, you must complete all the steps in one session. 1. Make sure the printer is turned on and not printing (the green P power light should be on, but not flashing). Then open the printer cover. 2. Press the e ink replacement button. The print head moves towards the center and the green P power light flashes. The red b error light also begins to flash or remains on.
4. Lift the cartridge out of the printer and dispose of it carefully. 5. Unwrap the new ink cartridge. Then remove only the yellow tape seal on top. Caution: You must remove the yellow tape from the top of the cartridge or you will permanently damage it. Don’t try to remove the clear seal underneath the cartridge. Don’t touch the green circuit board on the back of the cartridge; you may inhibit normal operation and printing. 6. Lower the new cartridge down into the holder.
7. Press down firmly on the ink cartridge clamp until it snaps in place. 8. If you need to replace the other ink cartridge, repeat steps 3 through 7 before continuing with step 9. 9. Press the e ink replacement button and close the printer cover. The printer begins charging the ink delivery system. The green P power light flashes and the printer makes noise. Charging takes about half a minute. When it’s finished, the green P power light stops flashing and stays on, and the red b error light goes out.
Aligning the Print Head If your printouts contain misaligned vertical lines, or you see white or black horizontal banding, you may need to align the print head. Note: Your printer must be connected directly to your computer (not over a network) to use the Print Head Alignment utility. 1. Turn on the printer. 2. Load plain, letter-size paper. 3. Windows: Right-click the printer icon on your taskbar (in the lower right corner of your screen) and select Print Head Alignment. Macintosh OS 8.5.1 to 9.
Cleaning the Printer To keep your printer working at its best, you should clean it several times a year. 1. Turn off the printer, unplug the power cord, and disconnect the printer cable. 2. Remove all paper, then use a soft brush to clean any dust or dirt from the sheet feeder. 3. Clean the exterior of the printer with a soft, damp cloth. Don’t touch the carriage shaft 4. Clean ink out of the printer’s interior with a soft, damp cloth. Clean here Warning: Don’t touch the gears inside the printer.
Transporting the Printer If you move your printer some distance, you need to prepare it for transportation in its original box or one of a similar size. Caution: To avoid damage, always leave the ink cartridges installed when transporting the printer. 1. Turn on the printer, wait until the print head locks in the far right position, then turn off the printer. 2. Unplug the power cord from the electrical outlet. Then disconnect the printer cable from the printer. 3.
Solving Problems This chapter gives you the basics for diagnosing and solving printer problems. First see “Diagnosing Printer Problems” on page 39 to help determine what the cause of the problem may be. Refer to the pictures on page 38 if you need help identifying parts of the printer. Tip: It’s a good idea to check EPSON’s support web site periodically for free updates to your printer driver. Visit http://support.epson.com. Download instructions are posted for your convenience.
Printer Parts Paper support Left edge guide Printer cover Output tray Output tray extension Ink cartridges and print head Maintenance button and error light Power button and light Ink replacement button 38 Solving Problems
Diagnosing Printer Problems First, check the printer’s lights as described below, or run a printer check as described on page 40. Lights Explanation Green P power light flashes The printer is receiving a print job, charging ink, or cleaning the print head. Red b light is on Your paper ran out, ink ran out, or paper is jammed. You may also see a message on your screen. ■ If paper is out, load more paper, then press the b maintenance button to resume printing.
Running a Printer Check You can run a printer check to determine whether a problem comes from the printer or some other source. 1. Turn off your printer and computer. 2. Disconnect the printer’s interface cable. 3. Load letter-size paper in the printer. 4. Hold down the b maintenance button, then press and release the Ppower button. Continue holding down the b maintenance button until the green P power light flashes, then release it.
Problems and Solutions Setup and Software Installation Problems The printer makes noise after ink cartridge installation. ■ ■ When you install ink cartridges, the printer must charge its print head for a few minutes. Wait until it’s finished (the green P power light stops flashing) before you turn off the printer, or it may use excess ink the next time you turn it on. Make sure the ink cartridge clamps are locked down completely and no packing material remains in the printer.
Printer Problems Only the green P power light is on, but nothing prints. ■ ■ ■ Make sure the interface cable is securely connected at both ends and meets the system requirements on pages 57 and 58. ■ Clear space on your hard drive or run a defragmentation utility. Run a printer check as described on page 40. If the check page prints, make sure your software is installed correctly. ■ Close programs that you’re not using. ■ Increase your system’s memory.
Print Quality Problems ■ Try using Automatic mode (Macintosh only); see page 13 (OS 8.5.1 to 9.x) or page 15 (OS X). ■ Align the print head as described on page 34. You see banding (light lines). Your printout is blurry or smeared. ■ Clean the print head; see page 27 for instructions. ■ Select a higher print quality and turn off High Speed mode; see page 17 (Windows) or page 20 (Macintosh) for details. ■ Select the correct Type (Windows) or Media Type (Macintosh) for your paper; see page 21.
Your printout is faint or has gaps. ■ Increase the image resolution or print it in a smaller size; see your software documentation. You see wrong or missing colors. ■ Make sure Black Ink Only is off (Windows) or Color ink is selected (Macintosh), even when printing black and white photographs. ■ Clean the print head; see page 27. ■ ■ Clean the print head; see page 27 for instructions. The ink cartridges may be old or low on ink; see page 29.
Paper Feeding Problems Miscellaneous Printout Problems Paper doesn’t feed correctly or jams in the printer. The image is inverted, as if viewed in a mirror. ■ If paper doesn’t feed, remove it from the sheet feeder. Fan the edges of the sheets, reload them against the right edge (beneath the tab), then slide the left edge guide against the paper. ■ If paper jams, press the b maintenance button to clear the jam. If necessary, open the cover and remove any jammed or torn pieces.
The margins are incorrect. ■ 46 Make sure the paper settings are correct for your paper size. See page 11 (Windows), page 12 (Macintosh OS 8.5.1 to 9.x), or page 14 (Macintosh OS X). ■ Choose the correct margins for your paper size. The margins must be within the printable area of the page; see “Printer Specifications” in your on-screen Reference Guide. ■ Make sure your paper is positioned next to the right side of the feeder and the left edge guide is lightly against the other side.
Uninstalling and Reinstalling Printer Software You may need to uninstall and then reinstall your printer driver and utilities if, for example, you upgrade your Windows operating system. You don’t need to uninstall EPSON Film Factory or your EPSON Printer Information Center. Windows 1. Click Start, and select Programs or All Programs. 2. Point to Epson or EPSON Printers, then select EPSON Printer Software Uninstall. 3. In the next window, make sure EPSON Stylus C62 Series is selected and click OK.
Macintosh OS X 1. Open the Applications folder, then the Utilities folder. 2. Select Print Center, select C62 Series, and click the Delete button. 3. Restart your Macintosh, then see page 49 to reinstall your software. Where To Get Help If you need help with your printer or Film Factory, see the contact information below. If you need help using other software with your printer, see the documentation for that software for technical support information.
Installing Your Printer Software Before installing your printer software, follow the steps on the Start Here sheet to set up your printer and connect it to your computer. If you’re using Windows XP, Windows Me, or Windows 98, or Mac OS 8.6 to 9.x, follow the software installation instructions on the Start Here sheet.
4. If you set up an administrator password, you see this screen. Click the lock icon, then enter your password, click OK, then click Continue. 5. Click Continue, then read and agree to the license agreement to continue the installation. 6. Select the OS X drive or partition and click Continue. Click the lock icon 7. When you see the Easy Install screen, click Install. 8. Follow the on-screen instructions to complete the installation and restart your Macintosh. 9.
13. Open the OS X Applications folder, then open the Utilities folder and select Print Center. Select Print Center Note: If you see this screen, click Add. If C62 Series already appears in the Printer list, go to step 16. 14. At the Printer List screen, click Add Printer. 15. Select EPSON USB, click C62 Series(USB), then click Add. Your printer appears in the printer list. 16. Close Print Center and start up your Macintosh in OS 9.x. Follow the instructions in the next section to install the OS 9.
Installing Printer Software for Mac OS 9.x 1. Select EPSON on your desktop, if necessary. Then select EPSON in the window that opens. 2. Read and agree to the license agreement to continue the installation. 3. Click Install Printer Driver and follow the on-screen instructions to install the driver and restart your Macintosh. 4. After your Macintosh restarts, register your printer with EPSON as instructed. 5. Open the Chooser in the Apple® menu.
Installing Printer Software on Windows 2000 1. Make sure your printer is set up, connected to your computer, and turned on, as described on the Start Here sheet. 2. Turn on your computer. 3. Wait for Windows to detect your printer connection and display a screen like this: Don’t click any buttons on the screen yet. Note: If this screen doesn’t appear, make sure your printer is turned on and connected. 4.
9. Installation proceeds automatically. At the final Found New Hardware Wizard screen, click Finish. 10. After a moment, you see a license agreement screen. Read and agree to the license agreement to continue the installation. 11. At the Options Menu, click Print a Test Page to check your installation. (If the page doesn’t print correctly, see page 41 for a solution.) 12. Click Install EPSON Software Film Factory; follow the on-screen instructions to install it on your system.
Installing Printer Software on Windows 95 1. Make sure your printer is set up, connected to your computer, and turned on, as described on the Start Here sheet. 2. Turn on your computer. If you see a New Hardware Found screen, click Cancel. 3. Put the EPSON CD-ROM in your CD-ROM or DVD drive. 4. Read and agree to the license agreement to continue the installation. 5. At the Install Menu, select Install Printer Driver and follow the on-screen instructions. 6.
56 Installing Your Printer Software
Requirements and Notices This chapter includes system requirements, safety instructions, legal notices, and other important information.
Macintosh System Requirements To use your printer and its software, your system should have: ■ A Power Macintosh® G3, G4, iMac™ or eMac™ with a built-in USB port ■ Mac® OS 8.5.1 through OS X 10.1 or higher. (Mac OS 9.0 or later recommended) ■ Mac OS 8.5.1 to 9.x: At least 64MB of available RAM (128MB recommended) Mac OS X: At least 128MB of available RAM (256MB recommended) ■ At least 100MB of free hard disk space (200MB recommended) ■ VGA display or better ■ A shielded USB “AB” cable up to 6.
Important Safety Instructions Before using your printer, read the following safety instructions to make sure you use the printer safely and effectively: ■ Be sure to follow all warnings and instructions marked on the printer. ■ Use only the type of power source indicated on the printer’s label. ■ Connect all equipment to properly grounded power outlets. Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off.
Ink Cartridge Safety Instructions 60 ■ Keep ink cartridges out of the reach of children and do not drink the ink. ■ Be careful when you handle used ink cartridges; there may be ink remaining around the ink supply port. If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water. ■ Do not put your hand inside the printer or touch the cartridge during printing. ■ Do not move the print head by hand. You may damage the printer.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Declaration of Conformity According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: EPSON AMERICA, INC. Located at: MS: 3-13 3840 Kilroy Airport Way Long Beach, CA 90806 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
securely packaging the defective unit or any requested parts and returning them to Epson within five (5) working days of receipt of the replacement. Epson requires a debit or a credit card number to secure the cost of the replacement printer in the event that you fail to return the defective one. If your printer is being repaired, Epson will direct you to send your printer to Epson or its authorized service center, where the printer will be fixed and sent back to you.
64 Requirements and Notices
Index Numerics 360 dpi Ink Jet Paper setting, 21 A Advanced settings, 17 to 20 Aligning print head, 34 Automatic mode, Macintosh, 13, 15, 44 B Background printing, 13 Banding, 43 Basic printing Macintosh, 12 to 16 Windows, 10 to 12 Black Ink Only setting, 17, 44 Blank pages, 45 Blurry images, 43 Bright White Paper, 21 Browser, 4 Buttons, 38 C Cable, printer, 57, 58 Cancelling printing Macintosh, 13, 16 Windows, 11 Characters, incorrect, 45 Checking printer, 40 Chooser, 41, 45 Cleaning print head, 27 to
EPSON help, 48 papers, 21 Printer Information Center, 2, 4 to 6 SoundAdvice, 48 Store, 30, 48 Warranty, 62 to 63 EPSON PhotoCenter, 2 Exif Print, 2, 22 to 26 F Faint images, 44 FCC Compliance Statement, 61 Film Factory, 2, 23 to 26 Flip Horizontal setting, 45 Ink cartridge level of ink in, 11, 13, 29 to 30 ordering, 30, 48 problems, solving, 44 replacing, 29 to 33 safety instructions, 30 to 32, 60 Ink Jet Transparencies, 21 Ink level, checking Macintosh, 13, 30 Windows, 11, 29 Installation problems, 41 In
Media Type setting Mac OS 8.5.1 to 9.
R U Reference Guide, 4 to 6 Reinstalling software, 47 to 48 Resolution Performance Management (RPM), 1, 17, 20 RPM, 1, 17, 20 Uninstalling software, 47 to 48 USB problems, 41 requirements, 57, 58 Utilities Head Cleaning, 27 to 29 Nozzle Check, 29 Print Head Alignment, 34 S Safety instructions, 59 to 60 Self adhesive sheets, 21 Semigloss Photo Paper, 21 Service, 48 Size setting, 9, 11 Slow printing, 42 Smeared printout, 43 Software installation problems, 41 installing, 49 to 55 problems, solving, 41 rein