® Epson SureColor T-Series ® Setup Guide Epson SureColor T-Series ® ® Printed in USA CPD-38235 CPD38235_Opera_SG_E.
Control Panel Power button and light Pause/cancel button Maintenance button Load/remove paper button Media feed button/cut button Menu button LCD display Back button CPD38235_Opera_SG_E.
Contents Unpacking and Assembling the Printer ..................................................................................................2 Assembling the Stand ......................................................................................................................3 Mounting the Printer on the Stand .................................................................................................5 Attaching the Paper Basket .................................................................
2 | Unpacking and Assembling the Printer Unpacking and Assembling the Printer Note: Unless otherwise indicated, the illustrations in this manual show the SureColor® T7000, but the instructions apply to all three models. Before beginning assembly, make sure you have sufficient space to set up and use the printer. The following illustration shows the minimum space required for using the printer: 5.9 in. (150 mm) 0.4 in. (10 mm) 23.6 in. (600 mm) 5.9 in.
Assembling the Stand | 3 The following items are included with your printer: Printer Hex wrench Horizontal strut Roll media adapter Legs Software and guides Power cord Ink cartridges Basket holders Plastic connector Basket arms Paper basket 1 square pole and 1 rounded pole Assembling the Stand 1. Unpack the stand and make sure you have all of these items.
4 | Assembling the Stand 2. Slide the horizontal strut into both of the legs as shown. 3. Use the long end of the hex wrench to tighten the pre-placed screws on each side of the horizontal strut. 4. Lock the casters to fix the stand in place. (When moving the printer, unlock the casters.
Mounting the Printer on the Stand | 5 Mounting the Printer on the Stand You need at least two people (SureColor T3000) or four people (SureColor T5000/T7000) to install the printer and position it on the stand. When lifting the printer, only hold the areas shown below. Otherwise, damage may occur. SureColor T3000 SureColor T5000/T7000 Caution: Before installing the printer, lock the casters to make sure the stand is fixed in place. 1. Lift the printer onto the stand.
6 | Attaching the Paper Basket 2. Attach the printer to the stand using three bolts. Attaching the Paper Basket The paper basket is a cloth sheet that attaches to the printer stand and catches your prints as they come out. You need the following parts to assemble and attach the paper basket: 1. Attach the two basket holders as shown, one on each side of the stand. Use four bolts to fasten the holders in place.
Attaching the Paper Basket | 7 2. Attach the stack guides to the bottom of the printer. Make sure each guide snaps securly into place. 3. Insert a plastic connector into one end of the square pole. 4. Slide the pole through the holes in the stack guides and attach the other plastic connector to the end of the pole. Then, fasten the plastic connectors in place on each side of the stand as shown.
8 | Attaching the Paper Basket 5. Attach the shorter arm to the inside of the basket holder on the left side of the printer. Use two nuts to hold the arm in place. 6. Use two bolts to fasten the arm in place. 7. Insert the longer arm into the rounded pole as shown.
Attaching the Paper Basket | 9 8. Slide the pole through the basket cloth until it comes out the other end. The small hole in the cloth will be on the right side as shown below. 9. Flip up the basket holder on the right side of the printer. 10. Insert the end of the rounded pole into the arm on the left side of the printer. Then, flip down the basket holder on the right side of the printer and insert the right-side basket arm as shown.
10 | Attaching the Paper Basket 11. Use two nuts and two bolts to fasten the arm in place. 12. On the back side of the printer, pull the paper basket up so that the stack guides fit into the slots as shown. Then, hook the loops around the pins on the back of the stack guides to hold the basket in place. 13. Hook the loops on the sides of the basket to the pins on the back of the stand legs to secure the basket to the printer.
Connecting the Power Cord | 11 14. On the front side of the printer, slide the basket’s fabric all the way to the ends of the rounded pole as shown. Connecting the Power Cord 1. Unlock the casters. Then, move the printer to the place of use. (The casters are meant for moving the printer for only a short distance.) Lock the casters after moving. 2. Connect the power cord to the AC inlet on the side of the printer. 3. Plug the power cord into a properly grounded electrical outlet.
12 | Installing Ink Cartridges Installing Ink Cartridges Use the ink cartridges that came with your printer for initial ink charging. During the initial installation process, it is normal for most of the ink in each cartridge to be used. 1. Turn on the power and configure the initial settings, such as the language and date. Then, follow the instructions on the control panel to install the ink cartridges. 2. Unpack the ink cartridges and shake each 30 times (about 10 seconds).
Loading Roll Paper | 13 4. Close the ink cover and wait for the ink to charge. The ink charging process takes about 22 minutes. Caution: Do not turn off the printer or open the ink cover when it is charging or you may waste ink. When the ink and Load paper will be displayed on the control panel. Do not perform charging is completed, press operations other than those specified on the screen. Loading Roll Paper Before you start, you may want to close the paper basket.
14 | Loading Roll Paper 1. Open the roll paper cover. 2. Raise the roll lock lever. 3. Place the roll on top of the printer.
Loading Roll Paper | 15 4. If necessary, adjust the roll media adapters to fit the core size of the roll paper. 2-inch core 3-inch core 2-inch 3-inch 5. Release the tension lever on both adapters. 6. Push the adapters into the paper core at both ends of the roll. Press the adapters in until they are fully inserted into the roll. 7. Push down the tension lever on both adapters to secure them.
16 | Loading Roll Paper 8. Slide the roll paper all the way to the right until it lines up with the adapter guides. 9. Press the button on the control panel. Confirm that Roll Paper is highlighted in the display, then press the OK button. 10. Insert the end of the roll paper into the paper slot and pull it through. Make sure the paper is free of slack and that the end is not folded.
Loading Roll Paper | 17 11. Pull the paper straight through until the leading edge reaches the front of the printer. 12. Lower the roll lock lever. 13. Following the instructions on the control panel, press the OK button. The paper will be fed into the printer.
18 | Loading Roll Paper 14. Close the roll paper cover. 15. Check the message on the control panel. 16. • If the paper type was automatically detected, the printer will display Ready on the LCD screen. The printer is ready to print. • If the paper type was not detected, the printer will display the Paper Type and Roll Paper Remaining settings for the paper currently selected. Follow the instructions on the control panel to change or confirm the current settings. Press OK when finished.
Performing a Test Print | 19 Performing a Test Print You can print a nozzle check from the control panel and examine it to determine whether any nozzles are clogged or deflected. Then you can run a cleaning cycle if necessary. 1. Make sure the paper source and media type settings are correct for the type of paper loaded. 2. Confirm that the printer is ready to print, then press the Maintenance menu will be displayed. 3. Confirm that Nozzle Check is highlighted and press the OK button.
20 | Aligning the Print Head Aligning the Print Head Follow the steps below to align the print head using the printer’s control panel. Make sure the paper source and media type settings are correct for the type of paper loaded. 1. Confirm that the printer is ready to print. Press l or r on the control panel to highlight and press OK. The Maintenance menu will be displayed. settings 2. Press d to select Head Alignment, then press OK. 3. Press d to select Auto (Bi-D), then press OK. 4.
Updating Your Printer Firmware | 21 To connect to a network hub or directly to your computer’s network interface, you need a standard RJ-45 CAT-6 network cable. 1. Plug the interface cable into the appropriate port on the printer. 2. Plug the other end of the cable into the appropriate port on your computer or network switch or hub.
22 | Updating the Firmware 3. Click Acquire Latest Information to automatically download the latest firmware version for your printer from the internet. If there is a firmware update, the message “Found the latest firmware information. Do you want to download the firmware file?” appears. Click Yes to download the file. Note: If the Acquire Latest Information button fails to download the latest firmware, you can also find it by visiting Epson’s support site epson.com/support (US) or epson.
EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. This information is subject to change without notice. © 2012 Epson America, Inc.
