Quick Start Manual

ManualsBrandsEpson ManualsPrintersEpson Epson WorkForce 1100

2 Open the output tray and pull out the extensions.

3 Squeeze the edge guide and slide it left.

4 Load paper against the right edge guide and behind the tab, with the

printable side face up.

Note: Don’t load the paper sideways; always load it short edge first.

5 Squeeze the edge guide and slide it over.

Install ink cartridges

Note: Don’t load paper before installing the ink cartridges.

1 Lift up the printer cover.

2 Open the cartridge cover.

3 Shake the ink cartridges gently 4 or 5 times, then unpack them.

4 Remove only the yellow tape from each cartridge.

Caution: Don’t remove any other seals from the cartridges.

5 Insert the cartridges in the holder for each color.

Unpack

If anything is missing, contact Epson

as described on the back of this sheet.

Caution: Do not open ink cartridge packages until you are ready to install the ink.

Cartridges are vacuum packed to maintain reliability.

Remove all protective materials.

Start Here

Please read these instructions before using the printer.

6 Press the cartridges down until they click.

7 Close the ink cartridge cover and press it down until it clicks.

8 Close the printer cover.

9 Press the ink button to charge the ink. Charging takes about

2.5 minutes.

Note: Your WorkForce 1100 Series ships with full cartridges and part of the ink

from the ﬁ rst cartridges is used for priming the printer.

Caution: Don’t turn off the printer while the power light is flashing or you’ll

waste ink.

Turn on the printer

1 Connect the power cable.

Caution: Do not connect to your computer yet.

2 Press the power button.

*411693900*

Load paper

1 Open the paper support and pull up the extensions.

Series

4116939 Rev.0

1-F C

4116939 Rev.0

1-F M

41136939 Rev.0

1-F Y

4116939 Rev.0

1-F K

CPD27483_Chor_SH_E.indd 1 6/5/09 1:27:29 PM

Summary of content (8 pages)

PAGE 1
Start Here Series Please read these instructions before using the printer. 1 Unpack If anything is missing, contact Epson® as described on the back of this sheet. 3 Install ink cartridges 6 Press the cartridges down until they click. 7 Close the ink cartridge cover and press it down until it clicks. 2 Open the output tray and pull out the extensions. 3 Squeeze the edge guide and slide it left. Note: Don’t load paper before installing the ink cartridges. 1 2 Lift up the printer cover.
PAGE 2
Start Here Series Please read these instructions before using the printer. 1 Unpack If anything is missing, contact Epson® as described on the back of this sheet. 3 Install ink cartridges 6 Press the cartridges down until they click. 7 Close the ink cartridge cover and press it down until it clicks. 2 Open the output tray and pull out the extensions. 3 Squeeze the edge guide and slide it left. Note: Don’t load paper before installing the ink cartridges. 1 2 Lift up the printer cover.
PAGE 3
Start Here Series Please read these instructions before using the printer. 1 Unpack If anything is missing, contact Epson® as described on the back of this sheet. 3 Install ink cartridges 6 Press the cartridges down until they click. 7 Close the ink cartridge cover and press it down until it clicks. 2 Open the output tray and pull out the extensions. 3 Squeeze the edge guide and slide it left. Note: Don’t load paper before installing the ink cartridges. 1 2 Lift up the printer cover.
PAGE 4
Start Here Series Please read these instructions before using the printer. 1 Unpack If anything is missing, contact Epson® as described on the back of this sheet. 3 Install ink cartridges 6 Press the cartridges down until they click. 7 Close the ink cartridge cover and press it down until it clicks. 2 Open the output tray and pull out the extensions. 3 Squeeze the edge guide and slide it left. Note: Don’t load paper before installing the ink cartridges. 1 2 Lift up the printer cover.
PAGE 5
Install software Your software works with Windows® 7, Windows Vista®, Windows XP Professional x64, Windows XP, Windows 2000, and Mac OS® X 10.3.9, 10.4.11, and 10.5.x. Macintosh® 1 Make sure the printer is NOT CONNECTED to your computer. Windows 1 Make sure the printer is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the WorkForce 1100 Series software CD.
PAGE 6
5 Install software Your software works with Windows® 7, Windows Vista®, Windows XP Professional x64, Windows XP, Windows 2000, and Mac OS® X 10.3.9, 10.4.11, and 10.5.x. Macintosh® 1 Make sure the printer is NOT CONNECTED to your computer. Windows 1 Make sure the printer is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the WorkForce 1100 Series software CD.
PAGE 7
5 Install software Your software works with Windows® 7, Windows Vista®, Windows XP Professional x64, Windows XP, Windows 2000, and Mac OS® X 10.3.9, 10.4.11, and 10.5.x. Macintosh® 1 Make sure the printer is NOT CONNECTED to your computer. Windows 1 Make sure the printer is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the WorkForce 1100 Series software CD.
PAGE 8
5 Install software Your software works with Windows® 7, Windows Vista®, Windows XP Professional x64, Windows XP, Windows 2000, and Mac OS® X 10.3.9, 10.4.11, and 10.5.x. Macintosh® 1 Make sure the printer is NOT CONNECTED to your computer. Windows 1 Make sure the printer is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can’t install your software that way. 2 Insert the WorkForce 1100 Series software CD.