EX3260/EX5260/Pro EX7260/Pro EX9210/ Pro EX9220/VS250/VS350/VS355 User's Guide
Contents EX3260/EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS250/VS350/VS355 User's Guide ................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents.............................................................................................
Connecting to a Component Video Source ............................................................................... Connecting to a Composite Video Source ................................................................................ Connecting to a Video Source for Sound .................................................................................. Connecting to External USB Devices ............................................................................................ USB Device Projection..
Selecting the Language for the Projector Menus................................................................................ 76 Adjusting the Image Height ................................................................................................................ 77 Image Shape...................................................................................................................................... 78 Correcting Image Shape with the Horizontal Keystone Slider ...............................
Password Security Types ............................................................................................................ Setting a Password ................................................................................................................. Selecting Password Security Types........................................................................................ Entering a Password to Use the Projector...............................................................................
Air Filter and Vent Maintenance .................................................................................................. Cleaning the Air Filter and Vents............................................................................................. Replacing the Air Filter............................................................................................................ Projector Lamp Maintenance...............................................................................................
Solutions When the Image Contains Static During Network Projection ....................................... 183 Solutions When Network Alert E-Mails are Not Received............................................................ 184 Where to Get Help............................................................................................................................ 184 Technical Specifications ................................................................................................................
EX3260/EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS250/VS350/VS355 User's Guide Welcome to the EX3260/EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS250/VS350/VS355 User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• Projection from iOS or Android devices and free Epson iProjection app; visit epson.com/iprojection (U.S.) or epson.
Make sure your projector boxes included all of these parts: 1 Projector 2 Remote control 3 Remote control batteries (two AA alkaline) 4 Power cord 5 VGA computer cable 6 USB cable (EX3260/EX5260/Pro EX7260/Pro EX9210/Pro EX9220) 7 Carrying case (EX3260/EX5260/Pro EX7260/Pro EX9210/Pro EX9220) 8 Wireless LAN module (EX5260/Pro EX9210) 9 Wireless LAN module cover (EX3260/EX5260/Pro EX9210/VS250/VS350/VS355) 10 Projector documentation CD 12
Parent topic: Projector Features Related concepts Projector Connections Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options.
Additional Projector Software and Manuals After connecting and setting up the projector, install the projector software from the included software CD, or download the software and manuals as necessary. You can install the projector software programs listed here and view their manuals for instructions on using them. Note: If you still need help after checking this manual and the sources listed here, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information.
Projector Parts - Front/Top 1 Exhaust vent 2 A/V Mute slide lever 3 Foot release lever 4 Lens cover 5 Front adjustable foot 6 Lens 7 Remote control receiver 8 Horizontal keystone slider 9 Air filter/intake vent 10 Air filter cover 11 Kensington security lock slot 12 Control panel 13 Zoom ring (EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355) 17
14 Focus ring 15 Lamp cover Parent topic: Projector Part Locations Projector Parts - Rear EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 1 AC input 2 Wireless LAN module cover screw (EX3260/EX5260/Pro EX9210/VS250/VS350/VS355) 3 Audio ports 4 Video port 18
5 Remote receiver 6 Speaker 7 HDMI port (EX3260/EX5260/VS250/VS350/VS355); HDMI/MHL port (Pro EX7260); HDMI1 and HDMI2/MHL ports (Pro EX9210/Pro EX9220) 8 Computer port 9 USB-B port 10 USB-A port Parent topic: Projector Part Locations Projector Parts - Base 19
1 Ceiling mount holes (3) 2 Security cable attachment point 3 Rear feet 4 Front adjustable foot Parent topic: Projector Part Locations Projector Parts - Control Panel EX3260/VS250 20
EX5260/Pro EX9210/VS350/VS355 Pro EX7260/Pro EX9220 1 Source Search button (searches for connected video sources) 2 Enter button (selects options) 21
3 Vertical keystone adjustment buttons (displays the adjustment screen and adjusts screen shape) and arrow buttons 4 Esc button (cancels/exits functions) 5 Volume buttons (adjust speaker volume; EX5260/Pro EX7260/Pro EX9210/Pro EX9220VS350/VS355), horizontal keystone adjustment buttons, and arrow buttons 6 Menu button (accesses projector menu system) 7 Home button (displays Home screen) 8 Power button 9 Status lights Parent topic: Projector Part Locations Related references Projector Light Sta
Projector Parts - Remote Control 1 Power button 23
2 Computer button (cycles through connected computer sources) 3 HDMI/Video button (cycles through connected HDMI/video sources) 4 Numeric buttons (enter numbers when you hold down the Num button) 5 Auto button (automatically adjusts position, tracking, and sync settings when projecting from a computer using a VGA cable) 6 Aspect button (selects the image aspect ratio) 7 Num button (when held down, switches numeric buttons to number function) 8 Menu button (accesses projector menu system) 9 Ar
27 Remote control signal emitter (emits remote control signals) Parent topic: Projector Part Locations 25
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
EX3260/VS250 4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 50 inches 58 to 79 inches –3.3 inches (–8 cm) (147 to 200 cm) 80 inches 93 to 126 inches –5.2 inches (–13 cm) (237 to 321 cm) 100 inches 117 to 158 inches –6.5 inches (–17 cm) (297 to 401 cm) 150 inches 176 to 237 inches –9.
Pro EX7260/VS355 16:10 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center (2) Wide to Tele 50 inches 55 to 66 inches –2.4 inches (–6 cm) (139 to 168 cm) 80 inches 88 to 106 inches –3.8 inches (–10 cm) (225 to 270 cm) 100 inches 111 to 133 inches –4.7 inches (–12 cm) (281 to 338 cm) 150 inches 167 to 200 inches –7.
Projector Connections See these sections to connect the projector to a variety of projection sources. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
2. Connect the cable to your projector's USB-B port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 3. Connect the other end to any available USB port on your computer. 4. Do one of the following: • Windows 10/Windows 8.x: Click EPSON_PJ_UD when it appears on the desktop, then select Run EMP_UDSE.EXE in the dialog box that appears to install the Epson USB Display software. • Windows 7/Windows Vista: Select Run EMP_UDSE.
The projector displays the image from your computer's desktop and outputs sound, if your presentation contains audio. Parent topic: Connecting to Computer Sources Connecting to a Computer for VGA Video You can connect the projector to your computer using a VGA computer cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.
Pro EX9210/Pro EX9220 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
2. Connect the other end to the projector's HDMI port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Note: The projector converts the digital audio signal sent from your computer into a mono analog signal for the internal speaker. Parent topic: Connecting to Computer Sources Connecting to a Computer for USB Mouse Control If you connected your computer to a Computer, USB-B, or HDMI port on the projector, you can set up the remote control to act as a wireless mouse.
1. Connect the USB cable to your projector's USB-B port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 2. Connect the other end to any available USB port on your computer. 3. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details.
1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port. 2. Connect the other end to the projector's Audio ports. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Parent topic: Connecting to Computer Sources Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
Connecting to a Composite Video Source Connecting to a Video Source for Sound Parent topic: Projector Connections Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable. The HDMI connection provides the best image quality. 1. Connect the HDMI cable to your video source's HDMI output port. 2. Connect the other end to the projector's HDMI port.
Parent topic: Connecting to Video Sources Connecting to an MHL-Compatible Device If you have an MHL-compatible smartphone or tablet, you can connect it to the projector using either an MHL cable or an HDMI cable with a device-compatible MHL adapter. If you have a device with a built-in MHL connector, plug it directly into the HDMI/MHL (Pro EX7260) or HDMI2/MHL (Pro EX9210/Pro EX9220) port. Note: Some connected devices may not charge when using an MHL adapter. 1.
Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker. Parent topic: Connecting to Video Sources Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1.
Pro EX9210/Pro EX9220 3. Tighten the screws on the VGA connector. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Signal menu. Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signal Menu Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1.
2. Connect the other end to the projector's Video port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Parent topic: Connecting to Video Sources Related tasks Connecting to a Video Source for Sound Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports. Connect the projector to the video source using an RCA audio cable. 1. Connect the audio cable to your video source's audio-out ports.
2. Connect the other end of the cable to the projector's Audio port or ports. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Parent topic: Connecting to Video Sources Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
Related topics Projecting a PC Free Presentation USB Device Projection You can project images and other content without using a computer or video device by connecting any of these devices to your projector: • USB flash drive • Digital camera or smartphone • USB hard drive • Multimedia storage viewer Note: Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices, and must be USB Mass Storage Class-compliant.
2. Connect the USB cable (or USB flash drive) to the projector's USB-A port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly. 3. Connect the other end of the cable (if applicable) to your device. Parent topic: Connecting to External USB Devices Selecting the Connected USB Source You can switch the projector's display to the source you connected to the USB-A port. 1.
2. Press the USB button on the remote control. Parent topic: Connecting to External USB Devices Disconnecting a USB Device or Camera From the Projector When you finish presenting with a connected USB device or camera, you must prepare to disconnect the device from the projector. 1. If the device has a power button, turn off and unplug the device. 2. Disconnect the USB device or camera from the projector.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Opening the Lens Cover To open the projector's lens cover, slide the A/V Mute slide lever until it clicks into the open position.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Wireless Network Projection You can project over a wireless network. To do this, you must set up your projector and computer for wireless projection.
Installing the Wireless LAN Module To use the projector over a wireless network, install the Epson 802.11b/g/n wireless LAN module in the projector (EX3260/EX5260/Pro EX9210/VS250/VS350/VS355). Do not install any other type of wireless module. Note: The wireless LAN module is not included with the EX3260/VS250/VS350/VS355 and is optional. Note: You do not need the wireless LAN module for the Pro EX7260/Pro EX9220 since the wireless functionality is built-in. 1. Remove the wireless LAN module cover screw.
2. Insert the wireless LAN module into the USB-A port. 3. Attach the wireless LAN module cover and secure it using the screw you removed. The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network.
Related references Optional Equipment and Replacement Parts Using a QR Code to Connect a Mobile Device After you select the wireless network settings for your projector, you can display a QR code on the screen and use it to connect a mobile device using the Epson iProjection app. Note: Make sure you have installed the latest version of Epson iProjection on your device. Visit epson.com/iprojection (U.S.) or epson.ca/iprojection (Canada) for more information. 1. Press the Menu button. 2.
4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Do one of the following: • Press the LAN button on the remote control. • Select Display the QR Code in the projector's Network menu. Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8.
1. Create a Quick Wireless Connection USB Key with a USB flash drive and the Epson iProjection (Windows/Mac) software. Note: See the online Epson iProjection Operation Guide (Windows/Mac) for instructions. 2. Turn on the projector. 3. Remove the wireless LAN module from the USB-A port (EX3260/EX5260/Pro EX9210/VS250/VS350/VS355). 4. Insert the USB key into the projector's USB-A port.
6. Reinsert the wireless LAN module into the projector (EX3260/EX5260/Pro EX9210/VS250/VS350/VS355). 7. Insert the USB key into a USB port on your computer. Note: In Windows Vista, if you see the AutoPlay window, select Run MPPLaunch.exe, then select Allow on the next screen. 8. Follow the on-screen instructions to install the Epson iProjection (Windows/Mac) software. Note: If you see a Windows Firewall message, click Yes to disable the firewall. You need administrator authority to install the software.
3. Select the Network menu and press Enter. 4. Make sure the Wireless Mode setting is set to Wireless LAN On. 5. Select Network Configuration and press Enter. 6. Select the Basic menu and press Enter.
7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in the Epson Web Control. (Default user name is EPSONREMOTE; default password is guest.
8. Select the Wireless LAN menu and press Enter. 9. Select the settings on the Wireless LAN menu as necessary for your network. 10. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. After you complete the wireless settings for your projector, you need to select the wireless network on your computer, or iOS or Android device.
Setting Options Description Search Access Point To Search View Search for available wireless network access points in Advanced connection mode SSID Up 32 alphanumeric characters Sets the SSID (network name) of the wireless LAN system the projector is connecting to Security Open WPA/WPA2-PSK Selects the type of wireless security used in the wireless network (some options are only available when the Connection Mode setting is set to Advanced) Passphrase Between 8 to 63 alphanumeric characters En
Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1. To access your wireless utility software, access the Desktop and double-click the network icon on the Windows taskbar. 2. Do one of the following: • If your projector is set up on an existing network (Advanced mode), select the network name (SSID). • If your projector is configured for Quick mode, select the projector's SSID. 3. Click Connect.
4. Select the Wireless LAN menu and press Enter. 5. Select the Security setting and press Enter. 6. Select the security settings for your network. 7. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Screen Mirroring Restrictions Note the following when using Screen Mirroring features (Pro EX9220): • You cannot project an interlaced image. • You cannot play audio with more than 3 channels. • You cannot project images with a resolution above 1920 × 1080 and a frame rate above 30 fps. • You cannot project 3D video. • You cannot use extended Miracast features on Windows 8.1. • You may not be able to view contents with copyright protection using a Miracast connection.
5. Select the Screen Mirroring Settings options as necessary. 6. When you finish selecting settings, select Set and follow the on-screen instructions to save your settings and exit the menus. 7. Press the Home button on the control panel or remote control. You see the Display Name you created on the Home screen.
The projector displays the image from your mobile device. Caution: It may take some time to establish the connection. Do not disconnect the projector's power cord while it is connecting to your device. Doing so may cause your device to freeze or malfunction. Note: Depending on the mobile device, you may need to delete a device when connecting. Follow the on-screen instructions on your device.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Notifications menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server setting. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7.
Parent topic: Using the Projector on a Network Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you receive an e-mail containing the following information: • The email address entered as the From setting • Epson Projector on the subject line • The name of the projector experiencing a problem • The IP address of the affected projector • Detailed information about the problem Note: If a critical problem causes a projector to
4. Select the Notifications menu and press Enter. 5. Turn on the SNMP setting. 6. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7.
Note: The web setup and control features support Microsoft Internet Explorer 9.0 or later, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser. Note: If you set Standby Mode to Communication On in the ECO menu, you can use a web browser to select settings and control projection even if the projector is in standby mode. 1. Make sure the projector is turned on. 2.
4. To select projector menu settings, select Advanced to display a list of options. Note: You may need to log in to access some of the options on the Web Control screen. If you see a log in window, enter your user name and password. (The default user name is EPSONWEB and the default password is admin.) 5. To control projection remotely, select the Basic Control option from the Web Control screen. Note: If you see a log in window, enter your user name and password.
2 Select an HDMI port source 3 Selects the USB Display source 4 Selects the USB device source 5 A/V Mute button control 6 Freeze button control 7 Page Up and Page Down button controls 8 Displays a QR code 9 Volume button controls 10 Selects the network source 11 Selects the Screen Mirroring source (Pro EX9220) 12 Selects the Computer port source 13 Selects a Video port source 14 Searches for connected sources 6.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the remote control to turn on the projector. The projector beeps and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue.
• If the Home screen is displayed, select the source you want to project. Using the Home Screen Parent topic: Using Basic Projector Features Related tasks Selecting an Image Source Using the Home Screen You can select input sources and other frequently used options from the Home screen. 1. To display the Home screen, do one of the following: • Press the Home button on the control panel or remote control. • Turn on the projector with the Home Screen Auto Disp setting enabled.
3 Display the Help screen 4 Display the projector's menus 5 Select customizable menu options 6 Depending on the projector, select to project two images from different image sources simultaneously or change the Power Consumption setting 7 Correct the image shape Note: Your Home screen may look different from the illustration shown here. You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3.
The projector displays a shutdown confirmation screen. 2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). 3. To transport or store the projector, make sure Status light is off, then unplug the power cord.
4. Close the projector's lens cover. Parent topic: Using Basic Projector Features Related references Projector Light Status Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the horizontal keystone slider on the projector to correct the image shape. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button). 2.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen. 3. Press a keystone button on the projector's control panel to adjust the image shape.
EX3260/VS250 EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355 Note: The horizontal keystone adjustment buttons are labeled W and T on the EX3260/VS250. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the H/V-Keystone settings in the projector menus.
Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the Quick Corner setting to correct the image shape. 1. Turn on the projector and display an image.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: 6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter.
7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Resizing the Image You can resize the image using the projector's zoom ring or the W and T buttons, depending on the projector model. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button).
EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355 Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring You can correct the focus using the focus ring. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the User button on the remote control (if the test pattern is assigned to this button). 2.
EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355 Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
1 30° 2 19.7 feet (6 m) 3 15° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
4. Use the following buttons on the remote control to control your presentation: • To move through slides or pages, press the up or down Page buttons. • To move the cursor on the screen, use the arrow buttons. • To left-click, press the button once (press it twice to double-click). • To right-click, press the Esc button. • To drag-and-drop, hold the at the destination.
1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen. Parent topic: Remote Control Operation Related references Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
3. Do one of the following: • Press the Source Search button on the projector or remote control until you see the image from the source you want. • Press the button for the source you want on the remote control.
• Press the Home button on the remote control or projector and select your image source. Note: Your Home screen may look different from the illustration shown here. Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen.
Changing the Projection Mode Using the Remote Control You can change the projection mode to flip the image over top-to-bottom. 1. Turn on the projector and display an image. 2. Hold down the A/V Mute button on the remote control for 5 to 10 seconds. The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for 5 to 10 seconds again.
3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio.
2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3. To cycle through the available aspect ratios for your input signal, press the Aspect button repeatedly. Note: If you are projecting from a computer and parts of the image are cut off, set the Resolution setting to Wide or Normal in the Signal menu.
Aspect ratio setting Description 16:9 Converts the aspect ratio of the image to 16:9. Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. Native Displays images as is (aspect ratio and resolution are maintained).
Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button. 3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment.
Controlling the Volume with the Volume Buttons You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio. You can also use the volume buttons on the projector's control panel (EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355). The volume buttons control the projector’s internal speaker system. You must adjust the volume separately for each connected input source. 1. Turn on the projector and start a presentation that includes audio. 2.
File type and extension Details Image (.jpg) Make sure the file is not: • CMYK format • Progressive format • Highly compressed • Above 8192 × 8192 resolution Image (.bmp) Make sure the file resolution is not above 1280 × 800 Image (.gif ) Make sure the file is not: • Above 1280 × 800 resolution • Animated • Interlaced Image (.png) Make sure the file resolution is not above 1280 × 800 Motion JPEG movie (.avi) Supports only AVI 1.
The PC Free screen appears. 2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter. (You can also press the Page up or down buttons on the remote control.) 3.
4. While projecting, use the following commands to control the display as necessary: • To rotate a displayed image, press the up or down arrow button. • To move to the next or previous image, press the left or right arrow button. 5. To stop the display, follow the on-screen instructions or press the Esc button.
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional files in a folder, highlight Next page or Previous page and press Enter. (You can also press the Page up or down buttons on the remote control.) 3.
Setting Options Description Display Order Name Order Displays files in name order Date Order Displays files in date order In Ascending Sorts files in first-to-last order In Descending Sorts files in last-to-first order On Displays a slide show continuously Off Displays a slide show one time through Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically; high resolution i
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
Note: You can also stop projection using the A/V Mute slide lever on the projector. Parent topic: Adjusting Projector Features Related references Projector Setup Settings - ECO Menu Related tasks Saving a User's Logo Image to Display Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1.
Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into.
Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings. • Button lock security to block operation of the projector using the buttons on the control panel. • Security cabling to physically cable the projector in place.
1. Hold down the Freeze button on the remote control for about five seconds or until you see this menu. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Press and hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again. You see the message "Password accepted.
Parent topic: Password Security Types Related tasks Selecting Password Security Types Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for about five seconds or until the menu appears. • To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On, press Enter again, and press Esc.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector. You must enter the correct password to use the projector. 1. Press and hold down the Num button on the remote control while you enter the password using the numeric buttons. Note: The default password is 0000. The password screen closes.
2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password three times in succession, you see a message telling you that the projector is locked. After the message is displayed for 5 minutes, the projector enters standby mode. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to enter the password.
2. Press the Menu button, select the Extended menu, and press Enter. 3. Select the User's Logo setting and press Enter. You see a prompt asking if you want to use the displayed image as a user's logo. 4. Select Yes and press Enter. You see a selection box overlaying your image. 5. Use the arrow buttons on the remote control to surround the image area you want to use as the User's Logo and press Enter. You see a prompt asking if you want to select this image area. 6. Select Yes and press Enter.
12. Select when you want to display the User's Logo screen: • To display it whenever there is no input signal, select Display Background and set it to Logo. • To display it whenever you turn the projector on, select Startup Screen and set it to On. • To display it whenever you press the A/V Mute button, select A/V Mute and set it to Logo. To prevent anyone from changing the User's Logo settings without first entering a password, set a password and enable User's Logo security.
You see a confirmation prompt. 6. Select Yes and press Enter. Unlocking the Projector's Buttons Parent topic: Projector Security Features Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them. You can also set the Control Panel Lock setting to Off in the Settings menu.
Projector Identification System for Multiple Projector Control You can operate multiple projectors using one remote control for more elaborate presentations. To do this, you assign an identification number to each projector and to the remote control. Then you can operate all the projectors at once or individually.
Parent topic: Projector Identification System for Multiple Projector Control Setting the Remote Control ID The remote control's ID is set to zero by default so it can operate any compatible projector. If you want to set the remote control to operate only a particular projector, you need to set the remote control's ID to match the projector's ID. Note: You must set the remote control ID to match the projector ID each time you turn on the projector you have set it to control. 1.
Matching Multiple-Projector Display Quality You can match the display quality of multiple projectors that will project next to each other. 1. Turn on all the projectors on which you want to match the display quality. 2. Set ID numbers on each projector. 3. Set the remote control ID to match the first projector. 4. Press the Menu button, select the Image menu, and press Enter. 5. Select settings as necessary. 6.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other (Pro EX7260/Pro EX9210/Pro EX9220/VS355). You can control the split screen feature using the remote control or the projector menus. Note: You cannot use split screen with certain input source combinations.
1. Press the Split button on the remote control. The currently selected input source moves to the left side of the screen. 2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter, select the input source, select Execute, and press Enter. (You can also change image sources, if necessary.) 4. To switch the images, select the Swap Screens setting and press Enter. 5.
6. To choose the audio you want to hear, select the Audio Source setting, press Enter, select an audio option, press Enter, and press Menu to exit. 7. To exit the split screen feature, press the Split or Esc button. Parent topic: Adjusting Projector Features Copying Menu Settings Between Projectors After you select menu settings for your projector, you can transfer them to another projector of the same model.
2. Insert the flash drive into the USB-A port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly.
3. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When all of the projector lights turn on, release the Esc button. The lights flash to indicate that settings are transferring to the flash drive. When the lights stop flashing, the power light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5.
Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have to repeat your adjustments. 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Insert the flash drive into the USB-A port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly.
3. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When all of the projector lights turn on, release the Menu button. The lights flash to indicate that settings are transferring to the projector. When the lights stop flashing, the power light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5.
• Windows 10 • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.x • macOS 10.12.x 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's USB-B port. EX3260/EX5260/Pro EX7260/VS250/VS350/VS355 Pro EX9210/Pro EX9220 3. Connect the other end to any available USB port on your computer.
4. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When all of the projector lights turn on, release the Esc button. The projector shows up as a removable disk on your computer. 6. Open the removable disk and copy the pjconfdata.bin file to your computer. 7. Once the file has copied, do one of the following: • Windows: Open the My Computer, Computer, Windows Explorer, or File Explorer utility.
• Windows 7 • Windows 8.x • Windows 10 • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.x • macOS 10.12.x Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have to repeat your adjustments. 1. Turn off the projector and unplug the power cord from the projector's power inlet. 2. Connect a USB cable to your projector's USB-B port.
Pro EX9210/Pro EX9220 3. Connect the other end to any available USB port on your computer. 4. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When all of the projector lights turn on, release the Menu button. The projector shows up as a removable disk on your computer.
6. Copy the pjconfdata.bin file from your computer to the removable disk. Note: Do not copy any other files to the removable disk. 7. Once the file has copied, do one of the following: • Windows: Open the My Computer, Computer, Windows Explorer, or File Explorer utility. Right-click the name of your projector (listed as a removable disk) and select Eject. • Mac: Drag the removable disk icon for your projector from the desktop into the trash.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
1. Press the Menu button on the control panel or remote control. You see the menu screen displaying the Image menu settings.
2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
Setting Options Description Color Mode See the list of available Color Modes Adjusts the vividness of image colors for various image types and environments Brightness Varying levels available Lightens or darkens the overall image Contrast Varying levels available Adjusts the difference between light and dark areas of the image Color Saturation Varying levels available Adjusts the intensity of the image colors Tint Varying levels available Adjusts the balance of green to magenta tones in the
Setting Options Description Advanced Deinterlacing Sets whether to convert interlaced to progressive signals for certain video image types Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Auto Iris Off Normal High Speed Adjusts the projected luminance based on the image brightness when the Dynamic or Cinema Color Modes are selected; High Speed sets faster luminance correction for fast-moving images Note: The Brightness setting do
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source. Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Sync.
Setting Options Description Input Signal Auto Specifies the signal type from input sources connected to computer ports RGB Component Auto: detects signals automatically RGB: corrects color for computer/RGB video inputs Component: corrects color for component video inputs Video Signal Auto Various video standards Specifies the signal type from the input sources connected to the video ports Auto: detects signals automatically Parent topic: Adjusting the Menu Settings Projector Feature Settings - S
Setting Options Description Keystone H/V Keystone Adjusts image shape to rectangular (horizontally and vertically) Quick Corner H/V Keystone: lets you manually correct horizontal and vertical sides; turn on or off Auto VKeystone and the H-Keystone Adjuster setting Quick Corner: select to correct image shape and alignment using an on-screen display Split Screen Screen Size (Pro EX7260/Pro EX9210/ Pro EX9220/VS355) Source Swap Screens Divides the viewing area horizontally and displays two images si
Setting Options Description Remote Receiver Front/Rear Limits reception of remote control signals by the selected receiver; Off turns off all receivers Front Rear Off User Button Power Consumption Info Assigns a menu option to the User button on the remote control for one-touch access Deinterlacing Closed Caption Test Pattern Resolution Display the QR Code Test Pattern — Displays a test pattern to assist in focusing and zooming the image and correcting image shape (press Esc to cancel pattern dis
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Select various options for the projector's Home screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen Display Background: selects the screen color or logo to display when no signal is received A/V Mute Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and s
Setting Options Description Operation Direct Power On Selects various operation options High Altitude Mode Direct Power On: turns on the projector when you plug it in Auto Source Search High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) Auto Power On HDMI EQ Setting Auto Source Search: automatically detects the image signal being input when the projector is turned on Auto Power On: automatically turns on the projector when it receives an imag
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Screen Mirroring Settings Various screen mirroring options Configures your screen mirroring settings; only available when Screen Mirroring On is selected as the Wireless Mode setting Connection mode Displays wireless network status and details (Pro EX9220) Net.
Projector Setup Settings - ECO Menu Settings on the ECO menu let you customize projector functions to save power. When you select a power-saving setting, a leaf icon appears next to the menu item.
Setting Options Description Sleep Mode Timer 1 to 30 minutes Sets the interval for Sleep Mode Lens Cover Timer On Automatically turns off the projector after 30 minutes if the lens cover is closed Off A/V Mute Timer On Automatically turns off the projector after 30 minutes if A/V Mute is enabled Off Standby Mode Communication On Communication Off ECO Display On Communication On indicates that the projector can be monitored and controlled over a network when the projector is in standby mode D
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Select Version to display the projector's firmware version. Select Projector Info to display the settings described below. Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Information item Description Refresh Rate Displays the refresh rate of the current input source Sync Info Displays information that may be needed by a service technician Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Event ID Displays the Event ID number corresponding to a specific projector problem; see the list of Event ID codes Event ID Code List Parent topic: Adjusting the Menu Settings Eve
Event ID code Cause and solution 0022 Unstable screen mirroring communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0027 0028 0029 0030 0031 0035 0023 0024 0025 Connection failed. If you see the PIN entry screen on your computer, enter the PIN code displayed on the Screen Mirroring standby screen or at the bottom right of the projected image.
Event ID code Cause and solution 0892 The WPA/WPA2 authentication type does not match. Make sure the wireless network security settings are correct. 0893 The TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct. 0894 Communication with unauthorized access point was disconnected. Contact your network administrator. 0898 Failed to acquire DHCP address. Make sure the DHCP server is operating correctly.
You cannot reset the following settings using the Reset All Config option: • Input Signal • User's Logo • Language • Network menu items • Lamp Hours • Password • Zoom (EX3260/VS250) • Display Background • Startup Screen • A/V Mute Parent topic: Adjusting the Menu Settings 151
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Related references Projector Light Status Cleaning the Air Filter and Vents Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them. 1. Turn off the projector and unplug the power cord. 2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
2. Carefully open the air filter cover.
3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Related references Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Parent topic: Projector Maintenance Related references Projector Light Status Projector Information Display - Info Menu Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Grasp the raised section of the lamp and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp's usage. Parent topic: Projector Lamp Maintenance Related references Optional Equipment and Replacement Parts Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1.
6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover as shown. 2. Remove the old batteries.
3. Insert the batteries with the + and – ends facing as shown. 4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Close the lens cover to protect the lens. • Remove any equipment connected to the projector. • Use a carrying case to hand-carry the projector. • When transporting the projector a long distance or as checked luggage, place it in a carrying case. Then pack the case in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solving Network Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp light Temp light Status and solution Flashing blue Light status varies Light status varies Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too hot Off Flashing blue Off Orange Projector has overheated and turned off; leave it turned off to cool down for about five minutes, then do the following:
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Off Lamp or lamp cover has a problem • Check to see if the lamp is burned out, broken, or installed incorrectly; reseat or replace the lamp as necessary • Clean or replace the air filter • If operating the projector at high altitude, turn on High Altitude Mode • If the problem persists, unplug the projector and contact Epson for help • Check that the lamp cover is installed correctly Flashing blue Light st
Wireless LAN status (Pro EX7260/Pro EX9220) Wireless LAN light Status and solution Blue Wireless LAN is available Flashing blue quickly Connecting to a device Flashing blue slowly An error has occurred; turn off the projector, then turn it back on Off Wireless LAN is not available; make sure the wireless LAN settings are correct Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help.
7. When you are finished, do one of the following: • To select another problem to solve, press Esc. • To exit the help system, press Home. Parent topic: Solving Problems Solving Image or Sound Problems Check the solutions in these sections if you have any problems with projected images or sound.
• Check the Display setting to make sure Messages is set to On. • If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons. • If the projector does not respond when you press buttons on the remote control, make sure the remote receivers are turned on. • For images projected with Windows Media Center, reduce the screen size from full screen mode. • For images projected from applications using Windows DirectX, turn off DirectX functions.
• If you are projecting using the 1080p video format and change the computer resolution during projection, the video quality and performance may decline. • Make sure you are using the most recent version of the USB Display software. You can download the latest version from the Epson web site. Go to epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.
Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1. Hold down the laptop's Fn key and press the key labeled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. To display on both the laptop's monitor and the projector, try pressing the same keys again.
Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal. • Make sure the Resolution setting in the Signal menu is set correctly for the input signal. • Try adjusting the image position using the Position menu setting.
• Adjust the Quick Corner setting to correct the image shape. Parent topic: Solving Image or Sound Problems Related concepts Image Shape Related references Projector Feature Settings - Settings Menu Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector.
Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen.
Solutions When the Image Brightness or Colors are Incorrect If the projected image is too dark or light, or the colors are incorrect, try the following solutions: • Press the Color Mode button on the remote control to try different color modes for the image and environment. • Check your video source settings. • Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Color Temp., and/or Color Saturation.
• Check the audio cable connections between the projector and your video source. • If you do not hear sound from an HDMI source, set the connected device to PCM output. • Make sure any connected audio cables are labeled "No Resistance". • If you are using the USB Display function, turn on the Output audio from the projector setting in the Epson USB Display Settings program on your computer.
• If the projector's lamp shuts off, the Status light is flashing blue, and the Temp light is orange, the projector has overheated and shut off. Check the solutions for this light status. • If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receiver setting is turned on in the projector's menu, if available. • The power cord may be defective. Try another power cord. If that doesn't work, disconnect the cord and contact Epson.
Related references Remote Control Operation Projector Feature Settings - Settings Menu Related tasks Replacing the Remote Control Batteries Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control. • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson.
Solutions When Network Alert E-Mails are Not Received Parent topic: Solving Problems Solutions When Wireless Authentication Fails If you cannot authenticate a wireless connection, try the following solutions: • Make sure the Wireless Mode setting is set to Wireless Lan On. • Check the Security settings and passphrase in the Network Configuration menu. • Check the Event ID number displayed in the Info menu and check the link below to identify the problem.
Related tasks Controlling a Networked Projector Using a Web Browser Solutions When You Cannot Connect Using Screen Mirroring If you are unable to connect to the projector using Screen Mirroring (Pro EX9220), try the following solutions: • Select Screen Mirroring On as the Wireless Mode setting in the projector's Network menu. • Make sure the Operation Mode and Channel settings are correct for your mobile environment and try connecting again.
• If the connection speed declines, reduce the number of connected devices. Parent topic: Solving Network Problems Solutions When Network Alert E-Mails are Not Received If you do not receive an e-mail alerting you to problems with a projector over the network, try the following solutions: • Make sure the projector is turned on and connected to the network correctly. (If an error shut down the projector, it cannot send an e-mail.
Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector.
Lens EX3260/VS250: F=1.44 Focal length: 16.7 mm EX5260/Pro EX7260/VS350/VS355: F=1.49 to 1.72 Focal length: 16.9 to 20.28 mm Pro EX9210/Pro EX9220: F=1.50 to 1.71 Focal length: 20.42 to 24.
EX5260/Pro EX7260/Pro EX9220: Normal Power Consumption mode: White light output 3600 lumens (ISO 21118 standard) Color light output 3600 lumens ECO Power Consumption mode: White light output 2235 lumens (ISO 21118 standard) Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.
Optical aspect ratio EX3260/EX5260/VS250/VS350: (width-to-height) 4:3 Pro EX7260/Pro EX9210/Pro EX9220/VS355: 16:10 Focus adjustment Manual Zoom adjustment EX3260/VS250: Digital zoom EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355: Manual optical zoom Zoom ratio EX3260/VS250: (Tele-to-Wide) 1.0 to 1.35 EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355: 1.0 to 1.
Lamp life Normal Power Consumption mode: Up to about 6000 hours ECO Power Consumption mode: Up to about 10000 hours Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications Reception range 19.
Weight VS250: 5.29 lb (2.4 kg) EX3260/EX5260/Pro EX7260/VS350/VS355: 5.51 lb (2.5 kg) Pro EX9210/Pro EX9220: 6.17 lb (2.8 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 V AC ±10% EX3260/EX5260/Pro EX7260/VS250/VS350/VS355: 3.1 to 1.3 A Pro EX9210/Pro EX9220: 3.3 to 1.
Power consumption EX3260/EX5260/Pro EX7260/VS250/VS350/VS355: (100 to 120 V) Operating: Normal Power Consumption mode: 296 W ECO Power Consumption mode: 211 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Pro EX9210: Operating: Normal Power Consumption mode: 315 W ECO Power Consumption mode: 228 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Pro EX9220: Operating: Normal Power Consumption mode: 315 W ECO Power Consumption mode: 228 W Standby: 2.2 W (Communication On), 0.
Power consumption EX3260/EX5260/Pro EX7260/VS250/VS350/VS355: (220 to 240 V) Operating: Normal Power Consumption mode: 282 W ECO Power Consumption mode: 203 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Pro EX9210: Operating: Normal Power Consumption mode: 298 W ECO Power Consumption mode: 219 W Standby: 2.0 W (Communication On), 0.2 W (Communication Off) Pro EX9220: Operating: Normal Power Consumption mode: 298 W ECO Power Consumption mode: 219 W Standby: 2.2 W (Communication On), 0.
Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No. 60950-1 Parent topic: Technical Specifications Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 70/75 1152 × 864 60 1280 × 960 60 1280 × 1024 60 1400 × 1050 TV (NTSC) 60 720 × 480 TV (SECAM) 50 720 × 576 TV (PAL) 50/60 720 × 576 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 SXGA 60 1280 × 960 60 1280 × 1024
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355 Display format Refresh rate (in Hz) Resolution (in pixels) VGA 60/72/75/85 640 × 480 SVGA 60/72/75/85 800 × 600 XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 60 1366 × 768 60/75/85 1280 × 800 WXGA+ 60/75/85 1440 × 900 WXGA++ 60 1600 × 900 SXGA 70/75/85 1152 × 864 60/75/85 1280 × 1024 60/75/85
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 60 1440 × 900 60 1600 × 900 60 1600 × 1200 WSXGA+ 60 1680 × 1050 SXGA 60 1280 × 960 60 1280 × 1024 60 1400 × 1050 WUXGA (Reduced Blanking) 60 1920 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/5
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 1 Wide resolution only for Pro EX7260/Pro EX9210/Pro EX9220/VS355 2 Pro EX9210/Pro EX9220 only 3 EX5260/Pro EX7260/Pro EX9210/Pro EX9220/VS350/VS355 only 4 Pro EX7260/Pro EX9210/Pro EX9220/VS355 only Parent topic: Technical Specifications USB Display System Requirements Your computer system must meet the sy
Requirement Windows Mac Hard disk space 20MB or more Display Resolution between 640 × 480 and 1920 × 1200, 16-bit color or greater Parent topic: Technical Specifications 199
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature. • Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
No. 5 6 Symbol Approved Standards Description IEC60417 Caution, hot surface No.5041 To indicate that the marked item can be hot and should not be touched without taking care. IEC60417 Caution, risk of electric shock No.6042 To identify equipment that has risk of electric shock. ISO3864-B3.6 7 8 9 IEC60417 For indoor use only No.5957 To identify electrical equipment designed primarily for indoor use. IEC60417 Polarity of DC power connector No.
No. 12 Symbol Approved Standards Description — Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. 13 14 15 16 17 18 IEC60417 Protective earth No.5019 To identify any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal of a protective earth electrode. IEC60417 Earth No.
No. Symbol 19 Approved Standards Description ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. 20 — Never look into the optical lens while the projector is on. 21 — To indicate that the marked item don’t place anything on projector. 22 ISO3864 Caution, laser radiation IEC60825-1 To indicate the equipment has a laser radiation part.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Epson, whether in contract, warranty, misrepresentation, fraud, tort, intentional tort, statute, regulation, ordinance, or any other legal or equitable basis. "DISPUTE" DOES NOT INCLUDE IP CLAIMS, or more specifically, a claim or cause of action for (a) trademark infringement or dilution, (b) patent infringement, (c) copyright infringement or misuse, or (d) trade secret misappropriation (an "IP Claim"). You and Epson also agree, notwithstanding Section 1.
WITHOUT THE WRITTEN CONSENT OF ALL AFFECTED PARTIES TO AN ARBITRATION PROCEEDING. 1.6 Arbitration Procedure. If you or Epson commences arbitration, the arbitration shall be governed by the rules of JAMS that are in effect when the arbitration is filed, excluding any rules that permit arbitration on a class or representative basis (the "JAMS Rules"), available at http://www.jamsadr.com or by calling 1-800-352-5267, and under the rules set forth in this Agreement.
c) Arbitration Fees. Epson shall pay, or (if applicable) reimburse you for, all JAMS filings and arbitrator fees for any arbitration commenced (by you or Epson) pursuant to provisions of this Agreement. d) Award in Your Favor.
Trademarks EPSON®, Instant Off®, and Quick Corner® are registered trademarks, Epson iProjectionTM is a trademark, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. Accolade® and PrivateLine® are registered trademarks; DuetTM and SizeWiseTM are trademarks; and Epson StoreSM and Extra CareSM are service marks of Epson America, Inc. Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. AndroidTM and ChromebookTM are trademarks of Google Inc.
This information is subject to change without notice. A Note Concerning Responsible Use of Copyrighted Materials Copyright Attribution Parent topic: Notices A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume.