Installation Guide

ManualsBrandsEpson ManualsPrintersEpson False Ceiling Plate Kit

Model: ELPMBP02

This product is UL Listed. It must be

installed by a qualified professional

installer.

Installation and Assembly:

False Ceiling Plate Kit

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Maximum UL Load Capacity: 50 lb (22.6 kg)

Manufactured by Peerless Industries, Inc.

Summary of content (6 pages)

PAGE 1
Installation and Assembly: False Ceiling Plate Kit Model: ELPMBP02 R This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 50 lb (22.6 kg) Manufactured by Peerless Industries, Inc. 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.
PAGE 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307.
PAGE 3
Before you begin, make sure all parts shown are included with your product. A Parts List A A1 B C D F G K L M AA BB CC Description Qty. Part # ceiling tray 1 128-2198 filler tray 1 128-2207 1/4"-20 x 3/8" screws 4 520-2015 1/4"-20 nuts 4 530-9302 allen wrench 1 560-9706 turnbuckle 4 560-9620 12 gauge x 20' (6.
PAGE 4
For Mounting Above Ceiling Tile 1 Place ceiling tray (A) in grid above 24" x 24" or 24" x 48" false ceiling tile with hole to center, left or right. 1-1 Place filler (A1) tray into gap. 1-2 Once placed where needed, through hole in ceiling tray (A), mark on false ceiling tile where hole will be. M 1-3 Cut out 2.25" hole in false ceiling tile. (Escutcheon Ring Accessory (ACC 640) is recommended).
PAGE 5
Anchoring Methods 3 Cut tie wire (G) into four pieces of equal length. Insert wires through the ends of the turnbuckles and loop to prevent the wire from slipping. Twist each wire around itself at least six times as tightly as possible. Drill holes for four ceiling anchors (see “Various Anchoring Methods”). Position the holes so when the tie wires are attached and taut the optimal angle is 15° (see figure 3.1 for reference). Unit may be mounted at an angle up to 45° if necessary.
PAGE 6
LIMITED FIVE-YEAR WARRANTY 3HHUOHVV ,QGXVWULHV ,QF HVWDEOLVKHV D ZDUUDQW\ SHULRG RI ÀYH \HDUV IRU SURGXFWV PDQXIDFWXUHG RU VXSSOLHG E\ 3HHUOHVV 7KLV SHULRG FRPPHQFHV IURP WKH GDWH RI VDOH RI WKH SURGXFW WR WKH RULJLQDO FRQVXPHU EXW ZLOO LQ QR FDVH ODVW IRU PRUH WKDQ VL[ \HDUV DIWHU WKH GDWH RI WKH SURGXFWҋV PDQXIDFWXUH 'XULQJ WKH ZDUUDQW\ SHULRG VXFK SURGXFWV ZLOO EH IUHH IURP GHIHFWV LQ PDWHULDO DQG ZRUNPDQVKLS SURYLGHG WKH\ DUH LQVWDOOHG DQG XVHG LQ FRPSOLDQFH ZLWK WKH LQVWUXFWLRQV HVWDEOLVKHG E