About the Manuals and Notations Used Types of Manual The documentation for your EPSON projector is divided into the following two manuals. Refer to the manuals in the order given below. Safety Instructions/Support and Service Guide This manual contains information on using the projector safely, and also includes a guide for warranty service, and a troubleshooting check sheet. Be sure to read this manual thoroughly before using the projector.
Checking the Components When you unpack the projector, make sure that you have all these components. If any of the components are missing or incorrect, please contact the place of purchase. ❏ Projector (with lens cover) ❏ Remote control ❏ Power cable (3.0m) Connect to the projector and to a wall outlet. ❏ AA-size alkali batteries (2 pcs.) Insert into the remote control.
Table of Contents ■ Features of the Projector............................. 4 ■ Part Names and Functions .......................... 6 Front / Top ...........................................................6 Control panel........................................................6 Remote control .................................................... 7 Rear...................................................................... 8 Base .....................................................................
Table of Contents ■ Problem Solving ........................................ 37 Reading the indicators........................................37 • When the (warning) indicator is lit or flashing ...............................................................37 • Indicator statuses in normal operation..................38 When the indicators provide no help ................. 39 • Problems relating to images................................. 39 • Problems when projection starts ..........................
Features of the Projector Image appearance can be selected to match the projection environment (Color Mode) The optimum images for the location can be projected simply by selecting the desired color mode from the following five preset modes. p.18 Dynamic Living Room Cinema Color Mode Natural If "Natural", "Cinema" or "x.v.Color" is selected, the Epson Cinema Filter effect is applied automatically to increase the contrast and to make skin tones appear with more natural tints. p.
Features of the Projector " " mode realizes more natural color reproduction This mode is compatible with the extended-gamut color space standard for video (xvYCC). Extended-gamut color images output by equipment supporting this standard are more faithful to the original, and the viewer can enjoy clearer, more natural images. p.
Part Names and Functions Front / Top • Horizontal lens adjustment dial • Remote control light- p.16 receiving area Turn the dial to move the position of the projection image to the left or right. • Lamp cover p.13 Receives signals from the remote control. See below • Vertical lens adjustment p.48 Open this cover when replacing the lamp inside. • Zoom ring • Top control panel dial p.16 Turn the dial to move the position of the projection image up or down. • Side control panel See below p.
Part Names and Functions Remote control • Remote control light-emitting area p.13 Outputs remote control signals. • Power button p.14, 15 Turns the projector power on/off. • Source buttons p.15 Switch between equipment connected to the projector. • Default button p.26 Restores default settings when menu is displayed. • Illumination button Illuminates all of the buttons on the remote control for 10 seconds so that they can be seen in dark places. • Esc button p.
Part Names and Functions Rear • [S-Video] input port p.12 Connects to the S-Video out ports of the video equipment. • [Video] input port • [PC] input port p.12 Connects to the RGB out port of the computer. • [RS-232C] port Connects to a computer using an RS-232C cable to control the projector from the computer. This is not used in normal use. • Lamp cover open switch p.12 Connects to the Composite Video output port of the video equipment. Press to open the lamp cover.
Appearance Center of lens 136 148.3 72* 12.3 4.5 131 450 * Distance from center of lens to suspension bracket fixing point 300 75 150 Center of lens 56 45 134.7 389.
Setting up Adjusting the projection size When the projector is further away from the screen, the projection image size are larger. While referring to the table below, position the projector so that the images are projected onto the screen at the optimum size. The values should be used as a guide for setting up the projector. Screen size Screen 90° A* Adjusting the projection size Center of lens B* *This is the distance from the center of the lens to the bottom of the projection images.
Setting up If you are installing the projector on the ceiling, this projector should be installed by qualified technicians using only approved mounting equipment. If installation work is not carried out correctly, the projector could fall down. This may result in injury or accidents. Contact your dealer to carry out the installation work.
Connecting Image Sources • Turn the power off for both the projector and the signal source before connecting them. If the power for either device is on at the time of connection, damage may result. • Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result. Video equipment (VHS VCR, DVD player, game console, etc.
Preparing the Remote Control Inserting batteries into the remote control At the time of purchase, the batteries are not inserted into the remote control. Insert the supplied batteries before using the remote control. Insert the batteries in the correct direction. Check the (+) and (-) indications inside the battery compartment and insert the batteries so that they face correctly. TIP Close the cover.
Starting and Stopping Projection Turning the power on and projecting images Do not look into the lens while projection is in progress. Remove the lens cover. Turn the power on. Control Panel Connect the power cable. (Commerciallyavailable) Remote Control Turn the power on for the connected equipment. Turn on the main power switch. ON If there is a problem with projection even though the projector is set up and connected correctly, refer to p.15, 37.
Starting and Stopping Projection When the expected images are not projected If more than one signal source has been connected, or if no images are projected, use the remote control or the projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video equipment first, then select the signal source.
Adjusting the Projection Screen Focus adjustment Turn the focus ring to adjust the focus. Projection size adjustment (Zoom adjustment) Turn the zoom ring to adjust the size of the projected image.
Adjusting the Projection Screen Adjusting the tilt of the projector When an image from the projector that is placed on a flat surface is tilting horizontally ( front feet to correct the tilt. Extend Retract Extend ), use the Retract Adjusting the tilt of the projector Displaying a test pattern You can use a test pattern to make the a firsttest setup such as zoom, focus, and image position using the lens Displaying pattern Adjusting the tilt of the projector again.
Basic Image Quality Adjustments Selecting the color mode Selecting the color mode Press and select the color mode from the menu. Setting is also possible using the configuration menu. Inputting a signal to the HDMI1/HDMI2 terminals. Selecting the aspect Selecting the aspect Select Menu Operations Use to select an item. Press to confirm the selection. *If you press disappears. , the Select menu Press and select the aspect mode from the menu.
Basic Image Quality Adjustments : Ideal for using in a bright room. : Ideal for using in a bright Living Room room. Provides clear and crisp images with vivid colors. : Ideal for using in a dark room. Natural It is recommended that you start in this mode when making color adjustments. Dynamic Cinema Normal : Ideal for watching movies and concerts in a dark room. : You can select from either of the signals being input to the HDMI1 and HDMI2 terminals.
Advanced Color Adjustments You can select "Sharpness" or "Advanced" in the "Image" menu to adjust the images according to your own preferences. The adjustment screens for "Gamma" and "RGBCMY" can be displayed on the screen directly by pressing the corresponding buttons on the remote control. The adjustment values can be stored in the memory so that you can retrieve them and apply them to the projected images at any time. ( p.
Advanced Color Adjustments Hue Adjusts the tone of the entire image to bluish, greenish and reddish. Saturation Use or (UP or DOWN) to select and confirm the color, and then select either "Hue", "Saturation" or "Brightness" and then use or (LEFT or RIGHT) to make the adjustment. Adjusts the overall vividness of the images. To adjust another color, press . To return the adjustment results to their default settings, press .
Advanced Color Adjustments RGB adjustment (Offset, Gain) The image brightness can be adjusted by adjusting the individual R (red), G (green) and B (blue) components of the dark areas (offset) and bright areas (gain). Adjustment is not possible when "Color Mode" is set to "x.v. Color". Press and then select "Image" - "Advanced" - "RGB" in that order and confirm the selection.
Examining Image Quality Further In addition to color adjustments, adjustments to advanced sharpness and the amount of light from the lamp can also be made to match the image in search of the best picture. Sharpness (Advanced) adjustment If "Thin Line Enhancement" is set in the + direction, hair and the detailed areas of clothing will be emphasized. If "Thick Line Enhancement" is set in the + direction, the areas emphasized by "Thin Line Enhancement" will be hardly emphasized.
Viewing Images at a Preset Image Quality (Memory Function) After using a subset of "Signal" and "Image" in the configuration menu to adjust the projected images, the adjusted values can then be saved (Save Memory). In addition, the saved data can be retrieved easily, so that you can enjoy viewing images with the adjusted settings at any time (Load Memory). Saving, Loading and Erasing memory Viewing Images at a Preset Image Quality (Save Memory) Up to ten adjustments can be saved to memory.
Viewing Images at a Preset Image Quality (Memory Function) Save Memory Load Memory Load saved memories. Adjust each of the settings to the values to be saved. Press , and select "Save Memory". The Save Memory screen is displayed. Press , and select "Load Memory". The Load Memory screen will be displayed. Select the target memory name. Select the memory name to register the adjustments to from Memory1 to 10, and press or .
Configuration Menu Functions The configuration menus can be used to make a variety of adjustments and settings involving image quality and input signals. The following two types of menu are available. ■ Full menu All items in the configuration menu can be checked while the settings are being made. Top menu Sub-menu ■ Line menu Some of the items in the "Image" menu in the Configuration menu can be adjusted.
Configuration Menu Functions Changing settings Example: Use or to adjust values. (green): Current setting value Use press If you press when an item with will be displayed. To return to a previous display, press TIP or to select an item, then . next to it is selected, the selection screen for that item . • For items such as "Brightness" which can be adjusted using an adjustment bar, the adjustment values can be reset to the default if you press while the adjustment bar is being displayed.
Configuration Menu Functions List of configuration menus When no image signals are being input, the "Image" menu and the "Signal" menu cannot be adjusted. Also, the items displayed in the "Image" menu, the "Signal" menu and the "Info" menu will vary depending on the type of image signals that are being projected. Image Not displayed when image signals are being input from a computer. Dynamic, Living Room, Natural, Theatre,Cinema, ("x.v.
Settings Configuration Menu Functions Direct Power On p.33 Sleep Mode p.33 p.36 Child Lock p.33 On, Off Control Panel Lock p.34 On, Off Trigger Out p.34 On, Off High Altitude Mode p.34 On, Off Projection p.34 Illumination p.34 Display On, Off Off, 5min., 10min., 30min. Front, Front/Ceiling, Rear, Rear/Ceiling On, Off p.
Configuration Menu Functions "Image" menu Not displayed when image signals are being input from a computer. Color Mode *1 Five different settings can be selected for the Color Mode, to match the images being projected or the projection environment. p.18 Brightness *2 (Adjustment is not possible when "Color Mode" is set to "x.v. Color".) Adjust this when the output level of the connected equipment is weak and you feel that images are dark.
Configuration Menu Functions Only displayed for Computer image input (does not appear when signals from the [HDMI1] /[HDMI2] input port are being input) RGBCMY *1 This lets you adjust the hue, saturation, and brightness for each of the R/G/B/C/M/Y color components. p.20 Power Consumption*2 This lets you set the lamp brightness to one of two settings. Set to "ECO" if the projection images are too bright when projecting in a dark room or projecting onto a small screen.
Configuration Menu Functions Not displayed when image signals are being input from a computer. Only displayed for Computer image input (does not appear when signals from the [HDMI1] /[HDMI2] input port are being input) Position * (Setting is not possible when signals are being input from the [HDMI1] /[HDMI2] input port.) When part of the image is clipped, move the image display position vertically and horizontally so that the entire image is projected. Press , , and to adjust the position.
Configuration Menu Functions Not displayed when image signals are being input from a computer. * Overscan (Setting is possible only when signals are being input from the [HDMI1]/[HDMI2]/[Component] input port.) This changes the display area (the part of projected images). • Off, 2%, 4%, 6%, 8%: If set to "Off", the top and the bottom of the image are sometimes affected by electrical interference depending on the image signal. In such cases, try to adjust the display position ("Position"). p.
Configuration Menu Functions Control Panel Lock If this is set to "On", you can't operate the projector's control panel buttons and a icon appears on the screen when a button is pressed. To cancel, press and hold on the projector's control panel for about seven seconds or more. If you change the setting, the new setting will take effect after exiting the configuration menu.
Configuration Menu Functions Input Signal Video Signal Sets the signal format in accordance with the video equipment that is connected to the [Video] or [SVideo] input port. If set to "Auto", the video signal format is set automatically. If there is a lot of interference in the image, or if a problem such as no image being projected occurs even though "Auto" has been selected, select the correct signal format manually.
Configuration Menu Functions "Memory" menu Load Memory This retrieves settings previously saved using "Save Memory". p.24 This cannot be selected when nothing is saved at "Save Memory". Save Memory This can be used to save "Image" menu settings. p.24 Erase Memory This is used to erase unwanted saved memory. p.25 "Reset" menu Reset All This resets all configuration menu settings to their default settings.
Problem Solving Reading the indicators The projector indicates its status using the indicators. (the icon and the around the button) and (the icon) light and flash, and lights and flashes in red according to the current status. The following tables show what the indicators mean and how to remedy the problems that they indicate. * If all indicators are switched off, check that the power cable is connected correctly and that the main power switch is on.
Problem Solving Lamp replacement warning It is time to replace the lamp. Replace the lamp with a new one as soon as possible. If you continue to use the projector without replacing the lamp, the lamp may blowout. p.50 Orange Indicator statuses in normal operation During normal operation, the indicator is off. : Lit : Flashing Standby condition If you press Warm-up in progress , projection will start after a brief interval. Warm-up time is approximately 30 seconds.
Problem Solving When the indicators provide no help If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem. Problems relating to images ● No images appear p.39 Projection does not start, the projection area is completely black, the projection area is completely blue, etc. ● Moving images are not displayed p.40 Moving images played on computer are not displayed. ● The message "Not Supported" is displayed p.
Problem Solving Are the image signal format settings correct? If a composite video or S-Video signal is being input If projection does not occur when the "Video Signal" menu command is set to "Auto", select the signal format that matches the signal source. "Settings" - "Input Signal" - "Video Signal" p.
Problem Solving ■ The message "No Signal" is displayed Are the cables connected correctly? Check that all of the cables required for projection are securely connected. p.12 Has the correct video input port been selected? Press Is the power for the connected equipment turned on? Turn the power on for the devices. Are the image signals being output to the projector? If the image signals are only being output to the computer's LCD monitor, you need to change the output.
Problem Solving Is an extension cable being used? If an extension cable is used, interference may increase. Try connecting a signal amplifier. Have the "Sync. " and "Tracking " settings been adjusted correctly? The projector has an automatic adjustment function that causes the optimum images to be projected. However, for some types of signal, the correct adjustments may not be obtained even after automatic adjustment is carried out. In such cases, use the "Tracking" and "Sync.
Problem Solving Have the color intensity and tint been adjusted correctly? Only when projecting images from a video source Use the "Color Saturation" and "Tint" menu commands to adjust the color and tint. "Image" - "Color Saturation", "Tint" p.30 ■ Images appear dark Has the image brightness been adjusted correctly? Use the "Brightness" menu commands to make the adjustments. "Image" - "Brightness" p.30 Has the image contrast been adjusted correctly? Use the "Contrast" menu command to adjust the color.
Problem Solving Problems with the remote control ■ The remote control does not work 44 Is the remote control lightemitting area facing towards the remote control light-receiving area when it is operated? Face the remote control towards the remote control light-receiving area. Operating range p.13 Is the remote control too far from the projector? The operating range for the remote control is approximately 10m. p.
Maintenance This section describes maintenance tasks such as cleaning the projector and replacing consumable parts. Cleaning You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. Do not use sprays containing a flammable gas to remove dirt or dust which is adhering to parts such as the lens or filter of the projector. Because the lamp inside the projector becomes very hot during use, the gases may ignite and result in a fire.
Maintenance Use a vacuum cleaner to remove any remaining dust from the surface of the air filter. Install the air filter. Install with the groove faced to the right. Install the air filter cover. Cleaning the projector case Clean the projector case by wiping it gently with a soft cloth. If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector case.
Maintenance Consumable replacement periods Air filter replacement period • If the air filter has been broken or the "Replace" message is displayed even though the air filter has been cleaned. Replacing the air filter p.48 Lamp replacement period • The message "Replace the lamp." appears on the screen when projection starts. A message will be displayed.
Maintenance Replacing consumables Replacing the air filter Press Do not touch the lamp cover soon after power-off or you may get burned because it is very hot. TIP Dispose of used air filters properly in accordance with your local regulations. Frame material: PP Filter materials: PP, PET or to turn off the power, and then turn the main power switch OFF. Remove the air filter cover. Press the knobs to release the catches, and then pull the cover upward.
Maintenance Remove the old air filter. Insert the new air filter. Install the air filter cover. Install with the groove faced to the right. Loosen the lamp fixing screws. Remove the old lamp. Insert the new lamp. Pull out straight. Make sure that it faces the correct way. Install the lamp and the lamp cover securely. The projector will not turn on if the lamp or the lamp cover is not installed correctly. Appendix This product includes a lamp component that contains mercury (Hg).
Optional Accessories/Consumables The following optional accessories/consumables are available for purchase if required. This list of optional accessories/consumables is current as of: 2010.7. Details of accessories are subject to change without notice. Varies depending on country of purchase. ■ Optional Accessories ■ Consumables 50" Portable Screen ELPSC06 A compact screen which can be carried easily. (Aspect Ratio 4:3) (1 spare lamp, 1 spare screwdriver) Use as a replacement for spent lamps.
List of Supported Monitor Displays Component Video Signal Refresh rate (Hz) Resolution (Dots) SDTV (480i) 60 720×480 SDTV(576i) 50 720×576 SDTV(480p) 60 720×480 SDTV(576p) 50 720×576 50/60 1280×720 HDTV(1080i) 50/60 1920×1080 HDTV(1080p) 50/60 1920×1080 HDTV (720p) Signal Refresh rate (Hz) Resolution (Dots) TV(NTSC ) 60 720×480 TV(SECAM ) 50 720×576 TV(PAL ) 50/60 720×576 Appendix Composite Video /S-Video 51
List of Supported Monitor Displays Input signal from the [HDMI1] / [HDMI2] input port Signal Refresh rate (Hz) Resolution (Dots) 60 640×480 SDTV (480i) 60 720×480 SDTV(576i) 50 720×576 SDTV(480p) 60 720×480 SDTV(576p) 50 720×576 HDTV (720p) 50/60 1280×720 HDTV(1080i) 50/60 1920×1080 HDTV(1080p) 24/30/50/60 1920×1080 VGA Computer image (analog RGB) Signal Refresh rate (Hz) Resolution (Dots) VGA 60/72/75/85 640×480 SVGA 56/60/72/75/85 800×600 XGA 60/70/75/85 1024×768 70
Specifications Product name EH-TW3600 EH-TW3200 450 (W) × 136 (H) × 360 (D) mm (not including feet) Dimensions 0.74 inch wide Panel size Polysilicon TFT active matrix Display method 2,073,600 pixels (1920 (W) × 1080 (H) dots) × 3 Resolution Scanning frequencies Pixel clock: 13.5 to 148.5 MHz Digital Horizontal: 15.63 to 67.5 kHz Vertical: 24, 50 to 60 Hz Pixel clock: 13.5 to 157.5 MHz Analogue Horizontal: 15.63 to 91.
Specifications Pixelworks DNXTM ICs are used in this Projector. This product is also designed for IT power distribution system with phase-to-phase voltage 230V. Product Information For users in Turkey: In Conformity with the Turkish EEE Regulation. Türkiye’deki kullanıcılar için EEE Yönetmeliğine Uygundur. ■ Angle of tilt If you set the projector higher than 8 º, it could damage the projector and cause an accident.
Specifications DECLARATION of CONFORMITY According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Tel: EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806 562-290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
Glossary Following is an explanation of some of the terms used in this guide which may be unfamiliar or which were not explained in the manual itself. Further information can be obtained by referring to other commercially-available publications. Aspect Ratio HDMITM The ratio between an image's length and its height. Wide screen refers to screens such as those for HDTV where the ratio between the width and the height is 16:9. The aspect ratio for SDTV and general computer screens is 4:3.
Glossary SECAM An abbreviation for Sequential Couleur A Memoire, and a format for ground-based analogue color television broadcasts. This format is used in France, Eastern Europe and the former Soviet Union, the Middle East and Africa. Security lock A device consisting of a protector case with a hole in it that a commercially-available theft-prevention cable can be passed through in order to secure the device to a table or pillar.
Index Numeric Character 2-2 Pull-down .................................................... 28, 32 A Abs. Color Temp. ............................................... 28, 30 Advanced .......................................................... 28, 30 Air filter .................................................................... 8 Aspect ................................................................ 18, 28, 31 Auto ................................................................................
Index Replacing the lamp ................................................... 48 Reset ................................................ 28, 29, 31, 33, 35 Reset All ................................................................... 29, 36 Reset Lamp Hours .............................................. 29, 48 Reset Memory .................................................... 29, 36 "Reset" menu ..................................................... 29, 36 Resolution............................................
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.