® Gebruikershandleiding NPDxxxx-00
Copyright en handelsmerken Copyright Geen enkel deel van deze publicatie mag worden gereproduceerd, worden opgeslagen in een gegevensopzoeksysteem of worden overgedragen in welke vorm of op welke wijze dan ook, hetzij elektronisch, mechanisch, via fotokopie of opname, of anderszins, zonder voorafgaande schriftelijke toestemming van Seiko Epson Corporation. De informatie in dit document is uitsluitend bedoeld voor gebruik met deze Epson-printer.
IBM® is een gedeponeerd handelsmerk van International Business Machines Corporation. Algemene opmerking: Andere productnamen die in deze documentatie worden gebruikt, worden uitsluitend ter identificatie gebruikt en zijn mogelijk handelsmerken van hun respectieve eigenaars. Epson maakt geen enkele aanspraak op deze merken. Copyright © 2006 Seiko Epson Corporation. All rights reserved.
Veiligheidsinstructies. Waarschuwingen, voorzorgsmaatregelen en opmerkingen w Waarschuwingen moeten zorgvuldig worden opgevolgd om lichamelijk letsel te voorkomen. c Voorzorgsmaatregelen: moeten worden nageleefd om schade aan de apparatuur te voorkomen. Opmerkingen bevatten belangrijke informatie en nuttige tips over het gebruik van uw printer. Waarschuwingssymbool voor hete onderdelen K Dit symbool staat op de printerkop en op andere onderdelen om aan te geven dat deze heet kunnen worden.
❏ Plaats de printer op een vlak, stabiel oppervlak. De printer werkt niet goed als deze schuin of in een hoek is geplaatst. ❏ Plaats dit product niet op een zacht, onstabiel oppervlak, zoals een bed of bank of in een kleine, afgesloten ruimte, aangezien de ventilatie hierdoor wordt belemmerd. ❏ Blokkeer of bedek de sleuven en openingen in de behuizing niet en duw geen voorwerpen in de sleuven. ❏ Gebruik alleen het type stroombron dat wordt aangegeven op het label van de printer.
Tijdens het onderhoud van de printer ❏ Verwijder de printerkabel uit het stopcontact voordat u de printer reinigt en reinig de printer uitsluitend met een vochtige doek. ❏ Mors geen vloeistoffen op de printer. ❏ Behalve zoals specifiek in deze handleiding wordt beschreven mag u zelf geen onderhoud aan de printer plegen. ❏ Verwijder de printerkabel uit het stopcontact en neem voor onderhoud contact op met bevoegd onderhoudspersoneel in de volgende gevallen: i. Als de stroomkabel of stekker is beschadigd. ii.
Met betrekking tot papiergebruik ❏ De afdrukkwaliteit van etiketten hangt af van de temperatuur en de luchtvochtigheid. Gebruik etiketten daarom alleen onder de normale gebruiksomstandigheden die hierna worden beschreven: Temperatuur: 15 tot 25 °C Luchtvochtigheid: 30 - 60% RH ❏ Laat geen etiketten in de printer achter tussen afdruktaken; ze kunnen om de plaat krullen en vastlopen wanneer het afdrukken wordt hervat. ❏ Plaats geen papier dat is omgekruld of gevouwen.
Voor gebruikers in het Verenigd Koninkrijk Gebruik van opties Epson (UK) Limited is niet aansprakelijk voor schade of problemen die het gevolg zijn van het gebruik van opties of verbruiksartikelen anders dan die door Epson (UK) Limited worden aangeduid als originele Epson-producten of door Epson goedgekeurde producten. Veiligheidsinformatie w Waarschuwing: Dit apparaat moet worden geaard.
De bruine draad moet worden verbonden met het aansluitpunt in de stekker met de letter L. Als de stekker is beschadigd, dient u de kabel te vervangen of een bevoegd elektricien te raadplegen. Vervang zekeringen alleen door een zekering met het juiste formaat en vermogen. Voor gebruikers in het Verenigd Koninkrijk, Singapore en Hongkong Vervang zekeringen alleen door zekeringen met het juiste formaat en vermogen.
Het internationale ENERGY STAR® Office Equipment-programma is een vrijwillige samenwerking tussen fabrikanten van computer- en kantoorapparatuur ter bevordering van de ontwikkeling van energiebesparende computers, beeldschermen, printers, faxapparaten, kopieerapparaten, scanners en multifunctionele apparaten om zo de luchtvervuiling door stroomopwekking terug te dringen. De gebruikte normen en logo's zijn voor alle deelnemende landen gelijk.
Inhoudsopgave Copyright en handelsmerken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handelsmerken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Veiligheidsinstructies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Waarschuwingen, voorzorgsmaatregelen en opmerkingen . . Waarschuwingssymbool voor hete onderdelen . . . . . . . . . .
Printersoftware De printersoftware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 De printerdriver gebruiken met Windows Me en 98 . . . . . . . . . . . 42 De printerdriver openen vanuit Windows-toepassingen . . . 43 De printerdriver openen via het menu Start . . . . . . . . . . . . . . 45 De instellingen voor de printerdriver wijzigen . . . . . . . . . . . 46 De printerdriver gebruiken met Windows XP, 2000 en Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . .
Probleemoplossing De foutindicatoren gebruiken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Problemen en oplossingen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Stroom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Afdrukken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Papierverwerking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Opties . . . .
Opdrachtenlijsten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EPSON ESC/P-besturingscodes . . . . . . . . . . . . . . . . . . . . . . . IBM 2380 Plus (voor LX-300+II)/ IBM 2381 Plus (voor LX-1170II)-emulatiebesturingscodes . . . . . . . . . . . . . . Standaarden en goedkeuringen . . . . . . . . . . . . . . . . . . . . . . . . . . . . Veiligheidsgoedkeuringen . . . . . . . . . . . . . . . . . . . . . . . . . . . . CE-markering. . . . . . . . . . . . . . . . . . . . . . . .
Leren werken met uw printer Functies Uw EPSON® LX-300+II/LX-1170II 9-pins dot-matrixprinter biedt afdrukken van hoge kwaliteit en superieure prestaties in een compacte eenheid. Tot de functies van de printer behoren: ❏ Verschillende papierbanen die precies aansluiten op uw wensen. ❏ De mogelijkheid om een groot aantal verschillende papiersoorten te verwerken, waaronder kettingpapier, meervoudige formulieren (met één origineel en maximaal vier kopieën), etiketten, losse vellen en enveloppen.
Papierverwerking Afdrukken op kettingpapier Uw printer kan kettingpapier met de tractor verwerken. Afhankelijk van de positie van de tractor, kunt u deze gebruiken als pull-tractor of als push-tractor.
Volg de onderstaande stappen om kettingpapier te laden met gebruik van de push-tractor: 1. Zorg ervoor de printer uitstaat. Verwijder het printerdeksel en de papiergeleider en plaats de papierontgrendelingshendel in de positie voor kettingpapier. 2. Ontgrendel de geleide-eenheden door de vergrendeling hiervan naar voren te trekken.
3. Verschuif de linkergeleide-eenheid en gebruik hierbij de schaal op de printer als richtlijn. De printer drukt rechts van de positie met de markering 0 af. Druk de vergrendelingshendel van de geleide-eenheid terug om de eenheid te vergrendelen. Verschuif vervolgens de rechtergeleide-eenheid om deze in te stellen op de breedte van het papier, maar vergrendel de eenheid niet. Verplaats de papiersteun totdat deze zich halverwege de geleide-eenheden bevindt. 4.
c Let op: Gebruik de knop voor de papierinvoer aan de rechterkant van de printer alleen om vastgelopen papier te verwijderen en alleen als de printer is uitgezet. Op die manier voorkomt u dat de printer beschadigd raakt of de positie voor de bovenkant van het formulier wordt verwijderd. 5. U kunt de papiergeleider gebruiken om het binnenkomende papier te scheiden van het afgedrukte papier.
7. Zorg ervoor dat het printerdeksel gesloten is. Druk op de knop LF/FF om het papier in de invoerpositie te plaatsen. Het afdrukken wordt gestart zodra de printer gegevens heeft ontvangen. 8. Nadat het afdrukken is voltooid, voert u de stappen in het volgende gedeelte uit om het afgedrukte document af te scheuren. Als de eerste afgedrukte regel op de pagina te hoog of te laag wordt weergegeven, kunt u de positie hiervan wijzigen met de functie Micro Adjust (Nauwkeurig aanpassen).
2. Open de afdekking van de papiergeleider en scheur het afgedrukte document af langs de daarvoor bestemde rand van de papierspanningseenheid. Opmerking: Als de perforatie van het papier niet goed is uitgelijnd met de afscheurrand, kunt u de afscheurpositie aanpassen met de functie Micro Adjust (Nauwkeurig aanpassen). Zie “De afscheurpositie aanpassen”. c Let op: Gebruik de knop voor papierinvoer nooit om de positie voor de bovenkant van het formulier te wijzigen.
c Let op: Scheur het afgedrukte document altijd af voordat u op de knop Load/Eject (Laden/Uitwerpen) drukt. Als meerdere pagina's tegelijk in omgekeerde volgorde worden ingevoerd, kan het papier vastlopen. Weer overschakelen op losse vellen Als u wilt overschakelen op losse vellen, drukt u op de knop Load/Eject (Laden/Uitwerpen). De printer voert het papier nu achterwaarts in de stand-bypositie. Voer daarna de stappen in “Losse vellen laden” uit.
c Let op: ❏ Gebruik de knop voor de papierinvoer aan de rechterkant van de printer alleen om vastgelopen papier te verwijderen en alleen als de printer is uitgezet. Op die manier voorkomt u dat de printer beschadigd raakt of de positie voor de bovenkant van het formulier wordt verwijderd. ❏ Als u de pull-tractor gebruikt, is het raadzaam de functie voor automatisch afscheuren in de modus Default Setting (Standaardinstelling) uit te schakelen om te voorkomen dat het papier vastloopt. 1.
2. Druk de vergrendelingsnokken van de tractor voorzichtig aan beide zijden samen en draai de tractor omhoog en uit de printer. 3. Verplaats de tractor naar voren naar de bevestigingssleuf bovenop de printer en kantel de tractor in de juiste positie (zie onderstaande afbeelding). Wanneer u de tractor op de nokjes drukt, klikt de tractor voelbaar vast.
4. Ontgrendel de geleide-eenheden door de vergrendeling hiervan naar voren te trekken. 5. Plaats het papier in de onderste papiersleuf of in de achterste papiersleuf (zie hieronder) en trek het omhoog. Positioneer het papier en gebruik hierbij de schaal op de printer als richtlijn. De printer drukt rechts van de positie met de markering 0 af.
6. Verschuif de linkergeleide-eenheid zodat de geleiders ervan overeenkomen met de positie van de gaten in het papier en vergrendel de eenheid. Verschuif vervolgens de rechtergeleide-eenheid om deze in te stellen op de breedte van het papier, maar vergrendel de eenheid niet. Verplaats de papiersteun totdat deze zich halverwege de twee geleide-eenheden bevindt. 7. Zorg ervoor dat het papier een scherpe, rechte invoerrand heeft. Open de afdekkingen van de geleide-eenheden.
Opmerking: Verwijder eventuele speling door voorzichtig vanaf de achter- of onderzijde aan het papier te trekken. 8. Als u het binnenkomende papier wilt scheiden van het afgedrukte papier, gebruikt u de papiergeleider. Houd de geleider horizontaal vast en plaats de inkepingen van de geleider over de bevestigingsnokjes van de printer.
De “bovenkant van formulier”-positie aanpassen De positie voor de bovenkant van het formulier is de positie op de pagina waarop het afdrukken wordt gestart. Als de afdruk te hoog of te laag op de pagina wordt weergegeven, kunt u de positie voor de bovenkant van het formulier wijzigen met de functie Micro Adjust (Nauwkeurig aanpassen). Voer de onderstaande stappen uit. c Let op: Gebruik de knop voor papierinvoer nooit om de positie voor de bovenkant van het formulier te wijzigen.
5. Druk op de knop LF/FF D als u de positie voor de bovenkant van het formulier hoger op de pagina wilt plaatsen, of druk op de knop Load/Eject U (Laden/Uitwerpen) als u de positie voor de bovenkant van het formulier lager op de pagina wilt plaatsen. * * plastic lintafdekking Opmerking: ❏ De printer heeft een minimum- en een maximumpositie voor de bovenkant van het formulier.
Zie het onderstaande voorbeeld als u de positie voor de bovenkant van het formulier wilt wijzigen voor kettingpapier dat is geplaatst op de pull-tractor: Markeer eerst een punt 2,5 mm (0,1 inch) boven de perforatie van het papier en plaats vervolgens het papier zodanig dat de markering samenvalt met de bovenrand van de pastic lintafdekking. Hierdoor ontstaat een marge van 8,5 mm (0,33 inch) op de volgende pagina. Dit betekent dat de printer 8,5 mm (0,33 inch) onder de perforatie begint met afdrukken.
Het papier doorvoeren naar de afscheurrand Als u de push-tractor gebruikt en u bent klaar met afdrukken, kunt u het kettingpapier met de afscheurfunctie doorvoeren naar de afscheurrand van de printer. U kunt het afgedrukte document dan gemakkelijk afscheuren. Wanneer u doorgaat met afdrukken, wordt het papier automatisch teruggevoerd naar de positie voor de bovenkant van het formulier, zodat het papier tussen documenten dat normaal gesproken verloren gaat, kan worden gebruikt.
Het papier automatisch doorvoeren naar de afscheurpositie Als u uw afgedrukte documenten automatisch wilt doorvoeren naar de afscheurpositie, dient u de modus voor automatisch afscheuren in te schakelen en de juiste paginalengte voor kettingpapier te selecteren in de modus Default Setting (Standaardinstelling). Zie “De standaardinstellingen wijzigen” voor instructies.
3. Houd de knop Pause (Onderbreken) gedurende drie seconden ingedrukt. Het lampje Pause (Onderbreken) begint te knipperen en de printer schakelt over op de modus Micro Adjust (Nauwkeurig aanpassen). 4. Druk op de knop LF/FF D om het papier achterwaarts in te voeren of druk op de knop Load/Eject (Laden/Uitwerpen) U om het papier voorwaarts in te voeren, totdat de papierperforatie is uitgelijnd met de afscheurrand. * * afscheurrand Opmerking: De printer heeft een minimum- en een maximumafscheurpositie.
Afdrukken op losse vellen U kunt losse vellen papier een voor een in de printer plaatsen met de papiergeleider van de printer. Zie “Papier” voor specificaties voor de soorten losse vellen die u kunt gebruiken. Voordat u afdrukt op losse vellen van meervoudige formulieren, enveloppen of ander speciaal papier, dient u de papierdiktehendel in te stellen op de juiste positie. Zie “Afdrukken op speciaal papier” voor meer informatie.
Losse vellen laden Voer de volgende stappen uit om losse vellen te laden: 1. Zorg ervoor de printer uitstaat. Controleer ook of de papierontgrendelingshendel naar achteren is gedrukt in de positie voor losse vellen en of de papiergeleider zich in de verticale positie bevindt (zie onderstaande afbeelding). 2. Verschuif de linkergeleider totdat deze wordt vergrendeld bij de geleidemarkering. Stel vervolgens de geleider voor de rechterrand in op de breedte van het papier dat u gebruikt.
3. Schuif een vel papier in de printer tussen de randgeleiders. Druk het papier goed aan tot u het niet verder kunt invoeren. Bij normaal gebruik zet u de printer aan zonder op andere knoppen te drukken. Het afdrukken wordt gestart zodra de printer gegevens heeft ontvangen. c Let op: Gebruik de knop voor de papierinvoer aan de rechterkant van de printer alleen om vastgelopen papier te verwijderen en alleen als de printer is uitgezet.
c Let op: Als u afdrukt op meervoudige formulieren die dikker zijn dan normaal papier, etiketten of enveloppen, dient u de toepassingssoftware zodanig in te stellen dat alleen in het afdrukbare gebied wordt afgedrukt. Wanneer verder dan de rand van deze papiersoorten wordt afgedrukt, kan de printerkop beschadigd raken. De papierdiktehendel aanpassen Voordat u op speciaal papier kunt afdrukken, dient u de instelling van de papierdiktehendel aan te passen.
2. Selecteer de juiste papierdikte aan de hand van de onderstaande tabel. Papiersoort Positie van hendel Standaardpapier (losse vellen of kettingpapier) 0 Meervoudige formulieren 0 1 2 3 2 vellen 3 vellen 4 vellen 5 vellen Etiketten 1 Enveloppen 2 of 4 3. Sluit het printerdeksel. Meervoudige formulieren U kunt meervoudige formulieren van maximaal veijf delen (één origineel plus vier kopieën) en zonder doorslag gebruiken op kettingpapier of losse vellen.
❏ Gebruik de toepassingssoftware of de instructies in “De bovenkant van formulier-positie aanpassen” als u de laadpositie moet aanpassen. ❏ Wanneer u meervoudige formulieren met hechting aan de zijkant gebruikt, vallen de kopieën mogelijk niet samen met het origineel. In dat geval kiest u een hogere waarde voor de papierdiktehendel. Etiketten Als u wilt afdrukken op etiketten, dient u de tractor te gebruiken als pull-tractor en papier te plaatsen via de onderste papiersleuf.
❏ Als u de etiketten uit de printer wilt verwijderen, scheurt u de nieuwe toevoer aan de onderkant van de printer af en vervolgens drukt u op LF/FF om de resterende etiketten uit te printer te voeren. c Let op: Voer etiketten nooit achterwaarts door de printer; de etiketten kunnen dan losraken van het achterblad en vastlopen in de printer. Als een etiket is vastgelopen in de printer, neemt u contact op met de dealer. Enveloppen U kunt enveloppen een voor een invoeren met de papiergeleider.
Printersoftware De printersoftware De Epson-software bevat de software voor de printerdriver en EPSON Status Monitor 3. De printerdriver is de software waarmee u via uw computer de printer kunt besturen. U dient de printerdriver te installeren om alle door de printer geboden mogelijkheden met uw Windows-toepassingen te kunnen gebruiken. Het programma EPSON Status Monitor 3 controleert de status van uw printer, waarschuwt u als er fouten optreden en biedt tips voor het oplossen van problemen.
De printerdriver gebruiken met Windows Me en 98 U kunt de printerdriver openen vanuit de Windows-toepassingen of via het menu Start. ❏ Wanneer u de printerdriver opent vanuit een Windows-toepassing, gelden de instellingen die u opgeeft alleen voor de toepassing die u gebruikt. Zie “De printerdriver openen vanuit Windows-toepassingen” voor meer informatie. ❏ Wanneer u de printerdriver opent via het menu Start, gelden de instellingen die u opgeeft voor de printerdriver voor alle toepassingen.
De printerdriver openen vanuit Windows-toepassingen Voer de onderstaande stappen uit als u de printerdriver wilt openen vanuit een Windows-toepassing. 1. Selecteer Print Setup (Printerinstelling) of Print (Afdrukken) in het menu File (Bestand) van de toepassing. Controleer in het venster Print (Afdrukken) of Print Setup (Printerinstelling) of uw printer is geselecteerd in de vervolgkeuzelijst Name (Naam).
2. Klik op Printer, Setup, Properties (Eigenschappen) of Options (Opties). (De knop waarop u klikt, hangt af van de toepassing die u gebruikt en u dient mogelijk op een combinatie van deze knoppen te klikken.) Het venster Properties (Eigenschappen) wordt weergegeven, met daarin de menu's Paper (Papier), Graphics (Afbeeldingen) en Device Options (Apparaatopties). Dit zijn de menu's met de instellingen voor de printerdriver. 3.
De printerdriver openen via het menu Start Voer de onderstaande stappen uit als u de printerdriver wilt openen via het menu Start. 1. Klik op de knop Start en wijs Settings (Instellingen) aan. 2. Klik op Printers. 3. Klik met de rechtermuisknop op het printerpictogram en klik op Properties (Eigenschappen). Het venster Properties (Eigenschappen) wordt weergegeven, met daarin de menu's Paper (Papier), Graphics (Afbeeldingen), Device Options (Apparaatopties) en Utility (Hulpprogramma).
De instellingen voor de printerdriver wijzigen De printerdriver heeft zeven menu's: Paper (Papier), Graphics (Afbeeldingen), Device Options (Apparaatopties), General (Algemeen), Details, Utility (Hulpprogramma) en Sharing (Delen). Zie “Overzicht instellingen de huidige printerdriver” voor een overzicht van de beschikbare instellingen. U kunt ook de online Help weergeven.
De printerdriver gebruiken met Windows XP, 2000 en Windows NT 4.0 U kunt de printerdriver openen vanuit de Windows-toepassingen of via het menu Start. ❏ Wanneer u de printerdriver opent vanuit een Windows-toepassing, gelden de instellingen die u opgeeft alleen voor de toepassing die u gebruikt. Zie “De printerdriver openen vanuit Windows-toepassingen” voor meer informatie.
De printerdriver openen vanuit Windows-toepassingen Voer de onderstaande stappen uit als u de printerdriver wilt openen vanuit een Windows-toepassing: Opmerking: De onderstaande voorbeelden zijn gebaseerd op het besturingssysteem Windows 2000. De onderdelen die op het scherm worden weergegeven, kunnen afwijken van de onderdelen op uw computer; maar de instructies zijn hetzelfde. 1. Selecteer Print Setup (Printerinstelling) of Print (Afdrukken) in het menu File (Bestand) van de toepassing.
2. Klik op Printer, Setup, Properties (Eigenschappen) of Options (Opties). (De knop waarop u klikt, hangt af van de toepassing die u gebruikt en u dient mogelijk op een combinatie van deze knoppen te klikken.) Het venster Document Properties (Eigenschappen van document) wordt weergegeven, met daarin de menu's Layout (Indeling) en Paper/Quality (Papier/Kwaliteit). Dit zijn de menu's met de instellingen voor de printerdriver.
3. U kunt een menu weergeven door te klikken op het bijbehorende tabblad bovenaan het venster. Zie “De instellingen voor de printerdriver wijzigen” als u de instellingen wilt wijzigen.
De printerdriver openen via het menu Start Voer de onderstaande stappen uit als u de printerdriver wilt openen via het menu Start. Opmerking: De schermafbeeldingen in de onderstaande procedure zijn gebaseerd op het besturingssysteem Windows 2000. De onderdelen die op het scherm worden weergegeven, kunnen afwijken van de onderdelen op uw computer; maar de instructies zijn hetzelfde. 1. Klik op de knop Start en wijs Settings (Instellingen) aan. 2. Klik op Printers. 3.
Als u klikt op Properties (Eigenschappen) in het menu dat wordt weergegeven nadat u met de rechtermuisknop op het printerpictogram hebt geklikt, wordt het venster Properties (Eigenschappen) weergegeven, met daarin menu's die worden gebruikt voor de instellingen voor de printerdriver. 4. U kunt een menu weergeven door te klikken op het bijbehorende tabblad bovenaan het venster. Zie “Overzicht instellingen de huidige printerdriver” voor informatie over het wijzigen van de instellingen.
De instellingen voor de printerdriver wijzigen De printerdriver heeft twee menu's waarmee u de instellingen voor de printerdriver kunt wijzigen, te weten Layout (Indeling) en Paper/Quality (Papier/Kwaliteit). U kunt instellingen ook wijzigen in het menu Utility (Hulpprogramma) in de printersoftware. Zie “Overzicht instellingen de huidige printerdriver” voor een overzicht van de beschikbare instellingen. U kunt ook de online Help weergeven.
Overzicht instellingen de huidige printerdriver In de onderstaande tabellen staan de instellingen voor de Windows-printerdriver. Niet alle instellingen zijn beschikbaar in alle versies van Windows. Printerinstellingen 54 Instellingen Uitleg Paper Size (Papierformaat) Selecteer het formaat van het papier dat u wilt gebruiken. Als u het gewenste papierformaat niet kunt zien, schuift u met de schuifbalk door de lijst.
Instellingen Uitleg Halftone Setup.../Halftone Color Adjustment... (Halftooninstelling/ Halftoonkleuraanp assing) Klik op deze knop als u de helderheid en het contrast wilt instellen, het RGB-gamma wilt invoeren of andere instellingen wilt opgeven. Het dialoogvenster Halftone Setup.../Halftone Color Adjustment... (Halftooninstelling/Halftoonkleuraanpassing) wordt weergegeven. Klik op de knop Help in dit dialoogvenster voor meer informatie.
Instellingen Uitleg Advanced Printing Features (Geavanceerde afdrukfuncties)* Schakel de metabestandsspooling in of uit. Print Optimizations (Afdrukoptimaliseri ngen)* Kies Disable (Uitschakelen) als de printer de apparaatlettertypen niet gebruikt en kies Enable (Inschakelen) als de printer de apparaatlettertypen wel gebruikt. Kleurenafdrukken (alleen voor LX-300+II) Bepaal of u in kleur wilt afdrukken. Als u kleurenafdrukken wilt maken, dient u de optionele upgradekit voor kleur te installeren.
3. Selecteer Server Properties (Eigenschappen voor server) in het bestandsmenu. 4. Schakel de optie Create a New Form (Nieuw formulier maken) in. 5. Geef het papierformaat op in de velden voor de afmetingen. 6. Klik op Save Form (Formulier opslaan) en klik vervolgens op OK. Controle-instellingen Instellingen Uitleg EPSON Status Monitor 3 Klik op deze knop om EPSON Status Monitor 3 te openen.
EPSON Status Monitor 3 gebruiken EPSON Status Monitor 3 is beschikbaar voor Windows XP, Me, 2000 en Windows NT 4.0. Met het programma kunt u de status van uw printer controleren en krijgt u waarschuwingen wanneer printerfouten optreden. Het programma biedt bovendien instructies voor het oplossen van problemen, indien nodig. EPSON Status Monitor 3 is beschikbaar als: ❏ De printer rechtstreeks is aangesloten op de hostcomputer via de parallelle poort [LPT1] of de USB-poort.
EPSON Status Monitor 3 instellen Voer de volgende stappen uit om EPSON Status Monitor 3 in te stellen: 1. Open het menu Utility (Hulpprogramma) zoals beschreven in “De printerdriver openen vanuit Windows-toepassingen” of “De printerdriver gebruiken met Windows XP, 2000 en Windows NT 4.0”. 2. Klik op de knop Monitoring Preferences (Controlevoorkeuren). Het dialoogvenster Monitoring Preferences (Controlevoorkeuren) wordt weergegeven.
3. De volgende instellingen zijn beschikbaar: Select Notification (Melding selecteren) Deze optie geeft de status van het selectievakje voor het foutitem weer (ingeschakeld of uitgeschakeld). Schakel het selectievakje in als u de geselecteerde foutmelding wilt weergeven. Select Shortcut Icon (Snelkoppelingspictog ram selecteren) Het geselecteerde pictogram wordt weergegeven op de taakbalk. Het voorbeeld van de instelling wordt weergegeven in het rechtervenster.
❏ Open het menu Utility (Hulpprogramma) en klik op het pictogram EPSON Status Monitor 3. Zie “De printerdriver openen vanuit Windows-toepassingen” of “De printerdriver gebruiken met Windows XP, 2000 en Windows NT 4.0” voor informatie over het openen van het menu Utility (Hulpprogramma). Als EPSON Status Monitor 3 op de hierboven beschreven manier wordt geopend, wordt het volgende venster voor de printerstatus weergegeven. In dit venster wordt informatie over de status van de printer weergegeven.
Opmerking: ❏ Selecteer uw land in het venster voor de taalselectie. ❏ Als het scherm EPSON Installation Program (EPSON-installatieprogramma) niet automatisch wordt weergegeven, dubbelklikt u op het pictogram My Computer (Deze computer) en klikt u met de rechtermuisknop op het cd-rompictogram. Klik op Open (Openen) in het menu dat wordt weergegeven en dubbelklik vervolgens op Epsetup.exe. 3. Klik op Continue (Doorgaan). Het scherm met de gebruiksrechtovereenkomst voor de software wordt nu weergegeven.
De printer instellen in een netwerk De printer delen In dit gedeelte wordt beschreven hoe u de printer kunt delen in een standaard Windows-netwerk. De computers in een netwerk kunnen een printer delen die rechtstreeks is aangesloten op een van de computers. De computer die rechtstreeks op de printer is aangesloten, fungeert als printerserver en de andere computers zijn de clients die toestemming nodig hebben om de printer te kunnen delen met de printerserver.
❏ Als u een onder Windows gedeelde printer gebruikt in een Windows Me- of 98-omgeving, dubbelklikt u op de server op het pictogram Network (Netwerk) in het configuratiescherm en controleert u of het onderdeel “File and printer sharing for Microsoft Networks” (Bestands- en printerdeling voor Microsoft-netwerken) is geïnstalleerd. Controleer vervolgens of het protocol “IPX/SPX compatible” (IPX/SPX-compatibel) of het “TCP/IP Protocol” (TCP/IP-protocol) is geïnstalleerd op de server en de clients.
Opmerking: ❏ Plaats de cd-rom van Windows Me of 98 in de computer wanneer u daarom gevraagd wordt. Klik op OK en volg de instructies op het scherm. ❏ Start de computer opnieuw op wanneer u daarom wordt gevraagd en ga verder met het instellen. 6. Dubbelklik op het pictogram Printers in het configuratiescherm. 7. Klik met de rechtermuisknop op het printerpictogram en klik op Sharing (Delen) in het menu dat wordt weergegeven. 8. Selecteer Shared As, typ de naam in het vak Share name (Share-naam) en klik op OK.
U dient de client-computers in te stellen, zodat deze de printer in een netwerk kunnen delen. Informatie hierover vindt u op de volgende pagina. ❏ “Onder Windows Me of 98” ❏ “Onder Windows XP of 2000” ❏ “Onder Windows NT 4.0” Onder Windows XP, 2000 of Windows NT 4.0 Als het besturingssysteem Windows XP, 2000 of Windows NT 4.0 wordt uitgevoerd op de printerserver, volgt u de onderstaande stappen om de printerserver in te stellen. Opmerking: U dient Windows XP, 2000 of Windows NT 4.
Als in Windows XP het volgende menu wordt weergegeven, klikt u op Network Setup Wizard (Wizard Netwerk instellen) of If you understand the security risks but want to share printers without running the wizard, click here (Klik hier als u het beveiligingsrisico kent maar bestanden zonder de wizard te gebruiken wilt delen). Volg in beide gevallen de instructies op het scherm. 3. Bij een Windows 2000- of een Windows NT 4.
Bij een Windows XP-printerserver selecteert u Share this printer (Deze printer delen). Vervolgens typt u de naam in het vak Share Name (Share-naam) en klikt u op OK. Opmerking: Gebruik geen spaties of verbindingsstreepjes in de share-naam, omdat daardoor een fout kan optreden. U dient de client-computers in te stellen, zodat deze de printer in een netwerk kunnen delen. Informatie hierover vindt u op de volgende pagina: ❏ “Onder Windows Me of 98” ❏ “Onder Windows XP of 2000” ❏ “Onder Windows NT 4.
❏ In dit gedeelte wordt beschreven hoe u de gedeelde printer kunt openen in een standaardnetwerksysteem via de server (Microsoft-werkgroep). Als u de gedeelde printer niet kunt openen vanwege het netwerksysteem, neemt u contact op met de netwerkbeheerder. ❏ In dit gedeelte wordt beschreven hoe u de printerdriver kunt installeren via de gedeelde printer vanuit de map Printers. U kunt de gedeelde printer ook openen vanuit de netwerkomgeving of My Network (Mijn netwerklocaties) op het bureaublad van Windows.
Opmerking: U kunt ook “\\(de naam van de computer die lokaal is aangesloten op de gedeelde printer)\(de naam van de gedeelde printer)” typen in het netwerkpad of de wachtrijnaam. 5. Klik op de computer of server die op de gedeelde printer is aangesloten, en op de naam van de gedeelde printer. Klik vervolgens op OK. Opmerking: De naam van de gedeelde printer wordt mogelijk gewijzigd door de computer of server die is aangesloten op de gedeelde printer.
❏ Als Windows Me of 98 niet wordt uitgevoerd op de printerserver, gaat u naar “De printerdriver installeren vanaf de cd-rom”. 7. Controleer de naam van de gedeelde printer en stel in of u de printer al dan niet als standaardprinter wilt gebruiken. Klik op OK en volg de instructies op het scherm. Opmerking: U kunt de naam van de gedeelde printer wijzigen, zodat deze alleen op de client-computer wordt weergegeven.
Als u Windows XP gebruikt, klikt u op het pictogram Add Printer (Printer toevoegen) in het menu Printer Tasks (Printertaken). 3. Selecteer Network printer (Netwerkprinter) (Windows 2000) of A network printer, or a printer attached to another computer (Netwerkprinter, of een printer die met een andere computer is verbonden) (Windows XP) en klik op Next. (Volgende). 4.
Opmerking: U kunt ook de naam van de gedeelde printer of het netwerkpad typen in het vak Name (Naam), zoals “\\(de naam van de computer die lokaal is aangesloten op de gedeelde printer)\(de naam van de gedeelde printer).” Als u Windows XP gebruikt, selecteert u Browse for a printer (Een printer zoeken) en klikt u op Next (Volgende). 5. Klik op het pictogram van de computer of server die op de gedeelde printer is aangesloten, en op de naam van de gedeelde printer. Klik vervolgens op Next (Volgende).
Opmerking: ❏ De naam van de gedeelde printer wordt mogelijk gewijzigd door de computer of server die is aangesloten op de gedeelde printer. U kunt contact op met de netwerkbeheerder om de naam van de gedeelde printer te controleren. ❏ Als de printerdriver vooraf is geïnstalleerd op de client, dient u het nieuwe of de huidige printerdriver te selecteren. Wanneer u wordt gevraagd de printerdriver te selecteren, selecteert u de printerdriver in het bericht.
Onder Windows NT 4.0 Voer de volgende stappen uit om Windows 4.0-clients in te stellen. U kunt de printerdriver van de gedeelde printer installeren als u een Hoofdgebruiker bent of hogere toegangsrechten hebt, zelfs als u geen beheerder bent. 1. Klik op Start, wijs Settings (Instellingen) aan en klik op Printers. 2. Dubbelklik op het pictogram Add Printer (Printer toevoegen). 3. Selecteer Network printer server (Netwerkprinterserver) en klik op Next (Volgende). 4.
❏ De naam van de gedeelde printer wordt mogelijk gewijzigd door de computer of server die is aangesloten op de gedeelde printer. U kunt contact op met de netwerkbeheerder om de naam van de gedeelde printer te controleren. ❏ Als de printerdriver vooraf is geïnstalleerd op de client, dient u het nieuwe of de huidige printerdriver te selecteren. Wanneer u wordt gevraagd de printerdriver te selecteren, selecteert u de printerdriver in het bericht. ❏ Als Windows 4.
1. Open de gedeelde printer. Er wordt mogelijk een bericht weergegeven. Klik op OK en volg de instructies op het scherm om de printerdriver vanaf de cd-rom te installeren. 2. Plaats de cd-rom. Het dialoogvenster EPSON Installation Program (EPSON-installatieprogramma) wordt weergegeven. Annuleer het dialoogvenster door te klikken op Cancel (Annuleren) en typ de stations- en mapnamen voor de locatie van de printerdriver voor clients. Klik vervolgens op OK.
Afdrukken annuleren Als de afdrukken niet aan uw verwachtingen voldoen en onjuiste of vreemde tekens of afbeeldingen bevatten, dient u het afdrukken wellicht te annuleren. Als het printerpictogram wordt weergegeven op de taakbalk, volgt u de onderstaande instructies om het afdrukken te annuleren. 1. Dubbelklik op het printerpictogram op de taakbalk en klik op Purge Print Documents (Afdrukdocumenten verwijderen) in het menu Printer. 2.
De printersoftware verwijderen Als u de printerdriver opnieuw wilt installeren of als u een upgrade voor de printersoftware wilt uitvoeren, dient u het geïnstalleerde de huidige printerdriver te verwijderen. De printerdriver en EPSON Status Monitor 3 verwijderen 1. Sluit alle toepassingen af. 2. Klik op Start, wijs Settings (Instellingen) aan en klik op Control Panel (Configuratiescherm). 3. Dubbelklik op het pictogram Add/Remove Programs (Software).
4. Selecteer EPSON Printer Software (EPSON-printersoftware) en klik op Add/Remove (Toevoegen/Verwijderen). 1 2 Opmerking: Wanneer u de computer met Windows XP of Windows 2000 gebruikt, klikt u op Change (Wijzigen) of Remove Programs (Programma's verwijderen); vervolgens selecteert u de EPSON Printer Software (EPSON-printersoftware) en u klikt op Change/Remove (Wijzigen/Verwijderen).
5. Klik op het tabblad Printer Model (Printermodel), selecteer het pictogram van de printer die u wilt verwijderen en klik op OK. 6. Als u gecontroleerde printers wilt verwijderen, klikt u op Yes (Ja) in het dialoogvenster dat wordt weergegeven. Opmerking: U kunt alleen het hulpprogramma Gecontroleerde printers van EPSON Status Monitor 3 verwijderen. Nadat u het hulpprogramma hebt verwijderd, kunt u de instelling van gecontroleerde printers niet meer wijzigen vanuit EPSON Status Monitor 3. 7.
Voer de onderstaande stappen uit om de driver van het USB-apparaat te verwijderen. Opmerking: ❏ Verwijder de printerdriver voordat u de driver van het USB-apparaat verwijdert. ❏ Nadat u de driver van het USB-apparaat hebt verwijderd, hebt u geen toegang meer tot de andere Epson-printers die zijn aangesloten via een USB-interfacekabel. 1. Volg stap 1 - 3 van “De printersoftware verwijderen”. 2. Selecteer EPSON USB Printer Devices (EPSON USB-afdrukapparaten) en klik op Add/Remove (Toevoegen/Verwijderen).
Opmerking: ❏ EPSON USB Printer Devices (EPSON USB-afdrukapparaten) wordt alleen weergegeven als de printer is aangesloten op computers met Windows Me of 98 via een USB-interfacekabel. ❏ Als de driver van het USB-apparaat niet correct is geïnstalleerd, wordt EPSON USB Printer Devices (EPSON USB-afdrukapparaten) mogelijk niet weergegeven. Volg deze stappen om het bestand “Epusbun.exe” op de cd-rom uit te voeren. 1. Plaats de cd-rom in het cd-romstation van uw computer. 2. Ga naar het cd-romstation. 3.
Bedieningspaneel Het bedieningspaneel gebruiken U kunt eenvoudige afdrukbewerkingen, zoals regeldoorvoer, formulierdoorvoer, papier laden en uitwerpen, en lettertypen selecteren, uitvoeren met de knoppen op het bedieningspaneel. De lampjes op het bedieningspaneel geven de printerstatus aan. Knoppen en lampjes op het bedieningspaneel 1 6 7 2 3 4 5 1. Tear Off (Font)-lampjes (Afscheuren (Lettertype))* Knipperen als kettingpapier in de afscheurpositie staat.
3. LF/FF-knop** ❏ Voert papier regel voor regel door indien de knop wordt ingedrukt en losgelaten. ❏ Werpt één vel uit of voert kettingpapier door naar de bovenkant van het eerstvolgende formulier indien de knop ingedrukt wordt gehouden. 4. Load/Eject-knop (Laden/Uitwerpen)** ❏ Laadt één vel papier. ❏ Werpt één vel papier uit als een vel papier is geladen. ❏ Laadt kettingpapier vanuit de stand-bypositie. ❏ Voert kettingpapier terug naar de stand-bypositie. 5.
* Lettertypeselectie: In de Micro Adjust-modus (Nauwkeurig aanpassen) kunt u het lettertype selecteren dat u wilt gebruiken door te drukken op de knop Tear Off (Font) (Afscheuren (Lettertype)). De Tear Off (Font)-lampjes (Afscheuren (Lettertype)) branden, knipperen of gaan uit om het geselecteerde lettertype aan te geven.
De standaardinstellingen van de printer De standaardinstellingen bepalen een groot aantal printerfuncties. Hoewel u deze functies vaak kunt instellen via de software of de printerdriver, moet u een standaardinstelling soms wijzigen via het bedieningspaneel van de printer, waarbij u de modus Default Setting (Standaardinstelling) gebruikt. In de volgende tabel worden de standaardinstellingen en de opties beschreven die u kunt selecteren in de modus Default Setting.
Instellingen Opties Parallel I/F bidirectional mode (Parallelle bidirectionele I/F-modus) On (Aan), Off (Uit) Packet mode (Pakketmodus) Auto, Off (Uit) Character table (Tekentabel)* Standaardmodel: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15 Alle andere modellen: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 866, PC 869, MAZOWIA, Code MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774, Estonia, ISO 8859-2,
Skip over perforation (Perforatie overslaan) Deze functie is alleen beschikbaar als kettingpapier is geselecteerd. Als u On (Aan) selecteert, voegt de printer een marge van één inch (25,4 mm) toe tussen de laatste afgedrukte regel op de ene pagina en de eerste afgedrukte regel op de volgende pagina.
Software Wanneer u ESC/P selecteert, werkt de printer in de EPSON ESC/P-modus. Wanneer u IBM 2380 Plus (voor LX-300+II)/ IBM 2381 Plus (voor LX-1170II) selecteer, emuleert de printer een IBM-printer. 0 slash (0 met schuine streep) Het nulteken heeft een schuine streep ( ) wanneer u deze functie inschakelt. De nul heeft geen schuine streep (0) als deze functie is uitgeschakeld. Dankzij de schuine streep kunt u gemakkelijker onderscheid maken tussen de hoofdletter O en een nul.
Baud rate (Baudrate) Gebruik deze optie om de gegevensoverdrachtssnelheid (baudrate) voor de seriële interface in te stellen. De baudrate wordt gemeten in bits per seconde (bps). Raadpleeg de computerhandleiding en softwaredocumentatie voor de juiste instelling. Parity (Pariteit) Als deze optie is ingesteld op None (Geen), is pariteitscontrole uitgeschakeld. Als het pariteitsbit wordt gebruikt, biedt dit een eenvoudige vorm van foutdetectie.
International character set for Italic table (Internationale tekenset voor Italic-tabel) U kunt kiezen uit diverse internationale tekensets voor de Italic-tekentabel. Elke tekenset bevat acht tekens die afhangen van het land of de taal, zodat u de Italic-tabel kunt aanpassen aan uw afdrukwensen. Manual feed wait time (Wachttijd voor handmatige invoer) Deze optie stelt de wachttijd in tussen het moment dat het papier in de papiergeleider wordt ingevoerd en het moment dat het wordt doorgevoerd.
De standaardinstellingen wijzigen Voer de volgende stappen uit om de modus Default Setting (Standaardinstelling) in te schakelen en de standaardinstellingen van de printer te wijzigen: Opmerking: ❏ Als u de instructies voor taalselectie en de instructies voor de modus Default Setting (Standaardinstelling) wilt afdrukken, hebt u vijf losse vellen papier van A4- of Letter-formaat nodig of vijf pagina's kettingpapier dat ten minste 279 mm (11 inch) lang en 210 mm (8,27 inch) breed is.
5. Houd de knop Tear Off (Font) (Afscheuren (Lettertype)) ingedrukt. De printer drukt de instructies voor de modus Default Setting (Standaardinstelling) (drie pagina's) af in de geselecteerde taal. In de afgedrukte instructies worden de standaardinstellingen vermeld die u kunt wijzigen, wordt beschreven hoe u ze kunt wijzigen en wordt uitgelegd hoe de lampjes op het bedieningspanel u helpen instellingen te selecteren. 6.
Probleemoplossing De foutindicatoren gebruiken U kunt een groot aantal algemene printerproblemen herkennen aan de lampjes op het bedieningspaneel. Als de printer niet meer werkt en één of meerdere lampjes op het bedieningspaneel branden of knipperen, of er klinkt een pieptoon, gebruik dan de onderstaande tabel om het probleem vast te stellen en op te lossen. Als u het probleem niet kunt verhelpen met de informatie in deze tabel, gaat u verder met het volgende gedeelte.
Lampje op paneel status Patroon pieptoon Probleem n Paper Out (Geen papier) n Pause (Onderbreken) ••• De geselecteerde papierbron is leeg. Oplossing Laad papier in de printer. Druk indien nodig op de knop Pause (Onderbreken) om het pauzelampje uit te zetten. ••• Het papier is niet correct geladen. Verwijder het papier en laad het opnieuw. Zie “Afdrukken op kettingpapier” voor instructies voor het laden van papier. Druk indien nodig op de knop Pause (Onderbreken) om het pauzelampje uit te zetten.
Lampje op paneel status Patroon pieptoon Probleem f Pause (Onderbreken) – De printerkop is oververhit. f Alle lampjes op het bedieningspa neel ••••• Oplossing Wacht een paar minuten. Zodra de printerkop is afgekoeld, wordt het afdrukken automatisch hervat. Er is een onbekende fout opgetreden. Zet de printer uit en laat deze een paar minuten uit staan. Zet de printer vervolgens weer aan. Als het probleem hiermee niet verholpen is, neemt u contact op met de dealer.
Opmerking: Als u een ervaren gebruiker of een programmeur bent, kunt u een hexadecimale dump afdrukken om communicatieproblemen tussen de printer en de computer te isoleren. Zet de printer uit als u een hexadecimale dump wilt afdrukken. Druk vervolgens op de knop Load/Eject (Laden/Uitwerpen) en houd deze ingedrukt en druk op de knoppen LF/FF terwijl u de printer aanzet. Stuur vervolgens gegevens vanaf de computer. De printer drukt alle ontvangen codes af in hexadecimale notatie.
Afdrukken De printer drukt niet af Het lampje Pause (Onderbreken) is uit, maar er wordt niets afgedrukt. Oorzaak Te verrichten handeling De software is mogelijk niet goed geïnstalleerd. Ga na of de software goed op de printer is geïnstalleerd (zie Begin hier). Controleer de printerinstellingen van de software. De interfacekabel voldoet mogelijk niet aan de specificaties van de printer of de computer. Controleer beide uiteinden van de interfacekabel.
Er zijn geluiden hoorbaar waardoor het lijkt alsof de printer afdrukt, maar er wordt niets afgedrukt. Oorzaak Te verrichten handeling De lintcassette is mogelijk niet goed geïnstalleerd. Zie Begin hier. Het lint is wellicht versleten. Vervang de lintcassette. Er is een vreemd geluid hoorbaar vanuit de printer, er klinken vijf pieptonen en de printer stopt plotseling. Oorzaak Te verrichten handeling Het papier of het lint zijn mogelijk vastgelopen.
De afdruk is vaag of onregelmatig. Delen van de onderkant van afgedrukte tekens ontbreken. Oorzaak Te verrichten handeling De lintcassette is mogelijk niet Zie “De lintcassette vervangen”. goed geïnstalleerd. De afdruk is vaag. Oorzaak Te verrichten handeling Het lint is wellicht versleten. Vervang de lintcassette aan de hand van de instructies in “De lintcassette vervangen”. Punten ontbreken in afgedrukte tekens of afbeeldingen Een regel met punten ontbreekt in de afdruk.
De afgedrukte tekens zijn niet naar verwachting. De tekststijl of tekens die u met uw software hebt verzonden, zijn niet afgedrukt. Oorzaak Te verrichten handeling De software is mogelijk niet goed geconfigureerd. Ga na of de software goed is geconfigureerd voor de printer. Het lettertype dat is geselecteerd op het bedieningspaneel wordt niet afgedrukt. Oorzaak Te verrichten handeling De software overschrijft mogelijk de instelling op het bedieningspaneel.
De paginalengte komt niet overeen met de lengte van het papier. Oorzaak Te verrichten handeling De instellingen voor de paginalengte in de toepassingssoftware zijn mogelijk onjuist. Controleer de paginalengte die in de toepassingssoftware is ingesteld en pas deze indien nodig aan. De paginalengte-instelling voor de tractor op de printer komt mogelijk niet overeen met die voor het kettingpapier dat u gebruikt. Controleer de paginalengte voor kettingpapier in de standaardinstellingen van de printer.
Papierverwerking Losse vellen worden niet goed ingevoerd Er wordt geen papier ingevoerd. Oorzaak Te verrichten handeling Er is mogelijk kettingpapier achtergebleven in de printer. Verwijder het kettingpapier. Zet de hendel daarna in de positie voor losse vellen. Plaats een nieuw vel papier. Verplaats het papier (en de Het papier voor de randgeleiders) iets naar links of naar papiergeleider is te ver naar links of naar rechts geplaatst, rechts. waardoor de printer het papier niet kan detecteren.
Kettingpapier wordt niet goed ingevoerd Het papier wordt niet ingevoerd door de tractor. Oorzaak Te verrichten handeling De papierontgrendelingshendel staat mogelijk in de verkeerde positie. Controleer of de papierontgrendelingshendel naar voren is getrokken in de positie voor kettingpapier. Als dit niet het geval is, zet u de printer uit en vervolgens weer aan. Het papier is mogelijk losgeraakt van de tractor. Plaats het papier weer goed in de tractor. Het papier wordt scheef ingevoerd of loopt vast.
U gebruikt mogelijk papier van een verkeerd formaat of met een verkeerde dikte. Zorg ervoor dat het formaat en de dikte van het papier voldoen aan de specificaties. Zie “Papier” voor informatie over de specificaties voor kettingpapier. Stel de papiergeleider iets hoger in om Wanneer u meervoudige formulieren met krimp aan de de afdrukpositie nauwkeurig te houden. zijkant gebruikt, vallen de afdrukken mogelijk niet samen met het origineel. Het papier wordt niet goed uitgeworpen.
Opties Het papier niet goed ingevoerd als u de invoer voor losse vellen gebruikt. Er wordt geen papier ingevoerd. Oorzaak Te verrichten handeling De invoer voor losse vellen is mogelijk niet goed op de printer geïnstalleerd. Installeer de invoer opnieuw aan de hand van de instructies onder “Invoer voor losse vellen”. De papierontgrendelingshendel Controleer of de papierontgrendelingsstaat mogelijk in de verkeerde hendel naar achteren is gedrukt in de positie. positie voor losse vellen.
Er worden twee of meer vellen tegelijk ingevoerd. Oorzaak Te verrichten handeling U hebt mogelijk te veel vellen Verwijder wat vellen papier. Zie “Papier” papier geplaatst in de invoer. voor informatie over de soort en de hoeveelheid papier die kan worden geplaatst met de invoer voor lossen vellen. U hebt wellicht de stapel papier niet uitgewaaierd voordat u deze in de invoer hebt geplaatst. Verwijder het papier en waaier het uit. Het papier wordt scheef ingevoerd.
Er kan niet goed worden overgeschakeld van de invoer voor lossen vellen naar de push-tractor en vice versa De gewenste papiersoort wordt niet ingevoerd. Oorzaak Te verrichten handeling De papierontgrendelingshendel Trek de hendel naar voren om bevindt zich mogelijk niet in de kettingpapier te laden of druk de hendel juiste positie. naar achteren om losse vellen te laden. Wanneer de pull-tractor wordt gebruikt met de push-tractor, wordt kettingpapier niet goed ingevoerd.
De upgradekit voor kleur is geïnstalleerd, maar de printer werkt niet goed (alleen LX-300+II). De lampjes op het bedieningspaneel gaan niet branden. Oorzaak Te verrichten handeling De motor in de upgradekit voor kleur is mogelijk niet goed geïnstalleerd. Volg de instructies onder “Kleurupgradekit (alleen LX-300+II)”. De gewenste kleur of bepaalde tekens worden niet afgedrukt. Oorzaak Te verrichten handeling De toepassingssoftware is mogelijk niet goed ingesteld voor afdrukken in kleur.
Problemen met de USB-aansluiting verhelpen Lees dit gedeelte als u problemen ondervindt bij het gebruik van de printer met een USB-aansluiting. Zorg ervoor dat u een model computer gebruikt waarop Windows XP, Me, 98 of 2000 vooraf is geïnstalleerd Uw computer dient een model te zijn waarop Windows XP, Me, 98 of 2000 vooraf is geïnstalleerd.
Als de stuurprogramma's goed zijn geïnstalleerd, wordt EPSON USB Printer Devices (EPSON USB-afdrukapparaten) weergegeven in het menu Device Manager (Apparaatbeheer). Als EPSON USB Printer Devices (EPSON USB-afdrukapparaten) niet wordt weergegeven in het menu Device Manager (Apparaatbeheer), klikt u op het plusteken (+) naast Other devices (Overige apparaten) om de geïnstalleerde apparaten weer te geven.
Als USB Printer (USB-printer), EPSON LX-300+II of EPSON LX-1170II niet wordt weergegeven onder Other devices (Overige apparaten), klikt u op Refresh (Vernieuwen) of koppelt u de USB-kabel los van de printer en sluit u de kabel weer aan op de printer. 4. Selecteer onder Other devices (Overige apparaten) USB Printer (USB-printer), EPSON LX-300+II of EPSON LX-1170II en klik op Remove (Verwijderen). Klik vervolgens op OK.
5. Als het onderstaande dialoogvenster wordt weergegeven, klikt u op OK. Klik vervolgens nogmaals op OK om het dialoogvenster System Properties (Systeemeigenschappen) te sluiten. 6. Zet de printer uit en start de computer opnieuw op. Installeer vervolgens de stuurprogramma's opnieuw aan de hand van de instructies in Begin hier.
❏ Bij Windows Me of 98 kunt u het USB-printerstuurprogramma en de printersoftware installeren. Verwijder eerst EPSON Printer Software (EPSON-printersoftware) met het onderdeel Add/Remove Programs (Software) in het configuratiescherm en verwijder vervolgens EPSON USB Printer Devices (EPSON-afdrukapparaten). Installeer daarna de software zoals wordt aangegeven in Begin hier.
c Let op: Gebruik voor de LX-300+II papier dat minimaal 210 mm (8,27 inch) breed is voor de zelftest; bij smaller papier drukt de printerkop rechtstreeks af op de plaat. Gebruik voor de LX-1170II papier dat minimaal 376 mm (14,8 inch) breed is voor de zelftest; bij smaller papier drukt de printerkop rechtstreeks af op de plaat. Voer de volgende stappen uit om een zelftest uit te voeren: 1.
4. Als u de zelftest wilt beëindigen, drukt u op de knop Pause (Onderbreken) om het afdrukken stop te zetten. Wanneer zich nog papier in de printer bevindt, drukt u op de knop LF/FF om de afgedrukte pagina uit te werpen. Zet vervolgens de printer uit. c Let op: Zet de printer niet uit wanneer de zelftest wordt afgedrukt. Druk altijd op de knop Pause (Onderbreken) om het afdrukken stop te zetten en op de knop LF/FF om de afgedrukte pagina uit te werpen voordat u de printer uitzet.
Contact opnemen met de klantenondersteuning Als uw Epson-product niet correct werkt en u het probleem niet kunt oplossen met behulp van de informatie voor probleemoplossing in de productdocumentatie, kunt u voor hulp contact opnemen met de klantenondersteuning. Raadpleeg het Europese garantiedocument voor informatie over hoe u contact opneemt met de klantenondersteuning van EPSON.
Opties en verbruiksmateriaal Opties installeren en gebruiken Invoer voor losse vellen De optionele invoer voor losse vellen (C80637✽ voor LX-300+II/C80639✽ voor LX-1170II) kan 50 vellen standaardpapier (82 g/m²) bevatten. Voer de onderstaande stappen uit om de invoer voor losse vellen te installeren. 1. Zorg ervoor de printer uitstaat. Verwijder de papiergeleider en open de afdekking van de papiergeleider. 2.
4. Houd de invoer voor losse vellen met beide handen vast en druk op de veerhendels. Plaats de inkepingen in de invoer voor losse vellen op de bevestigingspalletjes van de printer. Zodra u de veerhendels loslaat, wordt de invoer voor losse vellen op zijn plaats vergrendeld. * * veerhendel 5. Verschuif de linkerpapiergeleider zodanig dat deze is uitgelijnd met het driehoekje. Verschuif vervolgens de rechterpapiergeleider ongeveer naar de breedte van het gebruikte papier.
6. Trek de papierklemmen helemaal naar voren totdat de papiergeleiders worden ingetrokken en opengaan, zodat het papier kan worden geladen. 7. Pak een stapeltje papier en waaier het uit. Tik met de zijkant en de onderkant van het papier op een plat oppervlak, zodat de vellen gelijk liggen. c Let op: Gebruik geen enveloppen, meervoudige formulieren, carbonpapier of etiketten in de invoer voor losse vellen. 8. Leg maximaal 50 vellen papier langs de linkerpapiergeleider. 9.
12. Bevestig de papiergeleider aan de invoer voor losse vellen zoals hieronder wordt aangegeven. b a a. Bovenaanzicht b. Ontgrendelingslipje 13. Verschuif de linkerrandgeleider naar het midden totdat deze stopt bij de geleidemarkering. Verschuif vervolgens de rechterrandgeleider ongeveer naar de breedte van het gebruikte papier. Opmerking: ❏ Als u de papiergeleider uit de invoer voor losse vellen wilt verwijderen, drukt u op beide ontgrendelingslipjes en trekt u de papiergeleider eruit.
Opmerking: Wanneer u meerdere pagina's kettingpapier afdrukt, vouwt u de eerste afgedrukte pagina naar voren op de perforatie nadat de perforatie onder het printerdeksel tevoorschijn komt. Zo kan de printer de afgedrukte pagina's beter doorvoeren en wordt voorkomen dat het papier vastloopt. Pull-tractor Als optie is een extra pull-tractor (C80030✽ voor LX-300+II/C80034✽ voor LX-1170II) verkrijgbaar. U verbetert de verwerking van kettingpapier door twee tractors tegelijk te gebruiken.
3. Gebruikers van de LX-300+II pakken de pull-tractor met beide handen vast. Verplaats de tractor naar voren naar de bevestigingssleuf bovenop de printer tot de tractor in de juiste stand staat (zie onderstaande afbeelding). U moet de inkepingen vast voelen klikken. Gebruikers van de LX-1170II pakken de pull-tractor met beide handen vast. Druk de tractor omlaag in de bevestigingssleuf bovenop de printer en kantel de tractor in de juiste positie (zie onderstaande afbeelding).
6. Laat de vergrendelingshendels van de geleiders van de pull-tractor los en pas de geleiders aan de breedte van het papier aan. Zorg dat de geleiders op beide tractors zijn uitgelijnd, zodat het papier niet scheef wordt ingevoerd. 7. Open de afdekkingen van de geleide-eenheden. Plaats de gaatjes in het papier over de tractorpinnen van de geleiders en pas de geleiders zo nodig aan. (Zie “Afdrukken op kettingpapier”.) Sluit de afdekkingen van de geleiders. 8.
Papierrolhouder Dankzij de optionele papierrolhouder (#8310) kunt u uw printer gebruiken met een papierrol van 216 mm (8,5 inch), zoals die voor telexen wordt gebruikt. Deze optie is niet in alle landen beschikbaar. Voer de onderstaande stappen uit om de papierrolhouder te installeren en te gebruiken. 1. Zet de printer uit en verwijder de papiergeleider. 2. Plaats de papierrolhouder onder de printer, zoals hieronder wordt aangegeven.
4. Snijd de invoerrand van de papierrol recht af. Schuif de schacht van de papierrolhouder door het midden van de papierrol. 5. Plaats de schacht en de papierrol op de papierrolhouder. Plaats de rol zodanig dat het papier wordt ingevoerd vanaf de onderzijde van de rol. Zet vervolgens de printer aan. 6. Leid de invoerrand van het papier over de papierbaangeleider voor losse vellen en plaats het papier in de printerbaan voor losse vellen totdat u weerstand voelt. 7. Plaats de papiergeleider.
Kleurupgradekit (alleen LX-300+II) De optionele kleurupgradekit (C83208✽) bestaat uit een kleurenlintcassette en een motor. Voer de volgende stappen uit om de kit te installeren: 1. Zet de printer uit en verwijder het printerdeksel en de papierspanningseenheid. Schuif het klepje over de aansluitingen van de printer opzij en trek het eruit, zoals hieronder wordt aangegeven. 2. Plaats de motor in de rechterhoek van de printer, waarbij het aandrijfmechanisme naar het midden van de printer is gericht.
3. Plaats de stekker van de motor in de aansluiting op de printer. 4. Schuif de printerkop naar het midden van de printer en schuif het plastic gedeelte van het kleurenlint naar het midden van de cassette. 5. Draai de lintaandraaiknop in de richting van de pijl om het lint strak te trekken.
6. Plaats de lintcassette in de printer zoals wordt aangegeven en druk beide zijden van de cassette stevig aan, zodat de plastic haakjes in de openingen in de printer vallen. 7. Zet de printer aan terwijl u de knoppen Load/Eject (Laden/Uitwerpen) en Pause (Onderbreken) ingedrukt houdt. De printer drukt instructies af over hoe u de afdrukpositie aanpast. 8. Volg de afgedrukte instructies om de afdrukpositie aan te passen.
9. Zet de printer uit nadat u de afdrukpositie hebt aangepast. Opmerking: Wanneer u afdrukt met het kleurenlint, neemt de afdruksnelheid af. Als u wilt overschakelen naar het zwarte lint, verwijdert u het kleurenlint zoals wordt aangegeven in de handleiding van de optionele kleurupgradekit en installeert u het zwarte lint zoals wordt beschreven in “De lintcassette vervangen”. U hoeft de motor niet te verwijderen. Afdrukserver U kunt deze printer gebruiken als netwerkprinter door de EpsonNet 802.
De lintcassette vervangen Originele EPSON-lintcassette Wanneer de afdrukken vaag zijn, moet u de lintcassette vervangen. Originele EPSON-lintcassettes zijn ontworpen en geproduceerd voor een correcte werking met uw EPSON-printer. Ze zorgen voor een juiste werking en een lange gebruiksduur van de printerkop en andere printeronderdelen. Andere producten die niet zijn gemaakt door EPSON, kunnen uw printer schade toebrengen die niet door de garantie van EPSON wordt gedekt.
2. Zet het printerdeksel rechtop en trek het omhoog om het te verwijderen. 3. Gebruikers van de LX-1170II : verwijder de spanningseenheid door de vergrendelingsnokken van de eenheid voorzichtig samen te drukken en de papierspanningseenheid weg te trekken van de printer. 4. Gebruikers van de LX-300+II : controleer of de printerkop zich in het midden van de printer bevindt. Gebruikers van de LX-1170II: controleer of de printerkop zich op 10 cm (4 inch) afstand van de linkerkant bevindt.
7. Plaats de lintcassette in de printer zoals wordt aangegeven en druk beide zijden van de cassette stevig aan, zodat de plastic haakjes in de openingen in de printer vallen. 8. Gebruik een puntig voorwerp, zoals een balpen, om het lint tussen de printerkop en de lintgeleider te leiden.
9. Draai de lintaandraaiknop in de richting van de pijl om het lint correct in te voeren; het lint mag niet gedraaid of gevouwen zijn. 10. Voor gebruikers van LX-1170II: plaats de papierspanningseenheid terug. 11. Plaats het printerdeksel terug en sluit dit.
Productinformatie Printeronderdelen b a c h d g e f a. randgeleiders b. papiersteunen c. papiergeleider d. papierontgrendelingshendel e. draaiknop f. bedieningspaneel g. printerdeksel h.
b c a d e j i h g f a. seriële interface b. lintcassette c. papierdiktehendel d. papierspanningseenheid e. aan-/uitschakelaar f. voedingskabel g. USB-kabelhouder h. tractor i. USB-interface j.
Printerspecificaties Mechanisch Afdrukmethode: Afdruksnelheid Afdrukrichting: Regelafstand: Afdrukbare kolommen: Resolutie: 138 9-pins impact-dot-matrixprinter Snel concept 300 cps bij 10 cpi 337 cps bij 12 cpi 337 cps bij 15 cpi Snel concept, 321 cps bij 17cpi versmald 300 cps bij 20 cpi Concept 225 cps bij 10 cpi 270 cps bij 12 cpi 225 cps bij 15 cpi Concept versmald 191 cps bij 17 cpi 225 cps bij 20 cpi Concept met 112 cps bij 10 cpi nadruk NLQ 56 cps bij 10 cpi 67 cps bij 12 cpi 56 cps bij 15 cpi 4
Invoermethode: Frictie-invoer (papierinvoer aan achterzijde) Invoer via push-tractor (papierinvoer aan achterzijde) Invoer via push- en pull-tractor (papierinvoer aan achterzijde) Invoer via pull-tractor (papierinvoer aan achter- of onderzijde) Invoer: Push-tractor - achterzijde Invoer losse vellen (optioneel) Pull-tractoreenheid (optioneel) Papierrolhouder (optioneel) Papierinvoersnelheid: Continu 76 mm/seconde (3,0 inch/seconde) Met interval 63 msec/regel bij een interlinie van 1/6 inch Kleurenafdrukken
Afmetingen en gewicht (voor LX-300+II): Hoogte Breedte Diepte Afmetingen en gewicht (voor LX-1170II): Gewicht Hoogte Breedte Diepte Lint: Levensduur lint (Concept, 10 cpi, 14 punten/teken) 159 mm (6,26 inch) 366 mm (14,4 inch) 275 mm (10,8 inch) (zonder de draaiknop, papierontgrendelings hendel enz.) circa 4,4 kg (9,7 lb) 164 mm (6,6 inch) 546 mm (21,5 inch) 275 mm (10,8 inch) (zonder de draaiknop, papierontgrendelings hendel enz.) circa 6,6 kg (14,6 lb) Gewicht LX-300+II: Black ribbon cartridge (nr.
Elektronisch Interfaces: Eén standaard bidirectionele, 8-bits parallelle interface met ondersteuning voor IEEE-1284-Nibble-modus, één EIA-232D seriële interface en één USB-interface (versie 1.
Tekentabellen: Eén Italic en 12 grafische tekentabellen: Italic tekentabel, PC 437 (US, Standard Europe), PC 850 (Multilingual), PC 860 (Portuguese), PC 861 (Icelandic), PC 865 (Nordic), PC 863 (French-Canadian), BRASCII, Abicomp, ISO Latin 1, Roman 8, PC 858, ISO 8859-15 De volgende 26 grafische tekentabellen zijn ook in bepaalde landen beschikbaar: PC 437 Greek, PC 852 (Eastern Europe), PC 853 (Turkish), PC 855 (Cyrillic), PC 857 (Turkish), PC 866 (Russian), PC 869 (Greek), MAZOWIA (Poland), Code MJK (CS
Elektrisch 120 V-model Ingangsstroom 220 - 240 V-model 99 - 132 V 198 - 264 V Nominale frequentie 50 - 60 Hz Ingangsfrequentie 49,5 - 60,5 Hz Maximale stroomsterkte 0,6 A (maximaal 1,4 A afhankelijk van het tekentype) 0,3 A (maximaal 0,7 A afhankelijk van het tekentype) Stroomverbruik Circa 23 W (ISO/IEC 10561-letterpatroon) Opmerking: Het voltage van de printer staat aangegeven op het etiket op de achterkant van de printer.
Papier Opmerking: ❏ Gebruik kringlooppapier, -enveloppen, -etiketten en losbladige meervoudige formulieren alleen bij een normale temperatuur en luchtvochtigheid, binnen de volgende grenzen: Temperatuur: 15 - 25 °C (59 - 77 °F) Luchtvochtigheid: 30 - 60% RH ❏ Laad geen gevouwen, beschadigd, gekreukeld of omgekruld papier.
Losbladige meervoudige formulieren: invoer papiergeleider Breedte 100 - 257 mm (3,9 - 10,1 inch) Lengte 100 - 364 mm (3,9 - 14,3 inch) Kopieën 1 origineel + maximaal 4 kopieën Dikte 0,12 - 0,39 mm (0,0047 - 0,015 inch) Gewicht 40 - 58 g/m² (12 - 15 lb) Inbinding Lijmrand aan bovenkant of één zijkant van formulier Enveloppen: invoer papiergeleider Formaat Nr. 6: 165 × 92 mm (6,5 × 3,6 inch) Nr.
Etiketten: invoer onderzijde Etiketformaat minimaal 23,8 × 63,5 mm (15/16 × 2,5 inch) minimale radius 2,5 mm (0,1 inch) Breedte achterblad 101,6 - 254 mm (4,0 - 10,0 inch) Lengte achterblad 101,6 - 558,8 mm (4,0 - 22,0 inch) Dikte achterblad 0,07 - 0,09 mm (0,0028 - 0,0035 inch) Totale dikte 0,16 - 0,19 mm (0,0063 - 0,0075 inch) Gewicht etiket 64 g/m² (17 lb) Papierrol: invoer aan achterzijde bij optionele papierrolhouder Breedte 216 mm (8,5 inch) Dikte 0,07 - 0,09 mm (0,0028 - 0,0035 inch) Ge
Dikte Papiergeleider: 0,065 - 0,14 mm (0,0025 - 0,0055 inch) Invoer losse vellen: 0,07 - 0,14 mm (0,0028 - 0,0055 inch) Gewicht Papiergeleider: 52 - 90 g/m² (14 - 24 lb) Invoer losse vellen: 64 - 90 g/m² (18 - 24 lb) Losbladige meervoudige formulieren: invoer papiergeleider Breedte 148 - 420 mm (5,8 - 16,5 inch) Lengte 100 - 364 mm (3,9 - 14,3 inch) Kopieën 1 origineel + maximaal 4 kopieën Dikte 0,12 - 0,39 mm (0,0047 - 0,015 inch) Gewicht 40 - 58 g/m² (12 - 15 lb) Inbinding Lijmrand aan bove
Kettingpapier (standaard en meervoudig): invoer achter- en onderzijde Breedte 101,6 - 406,4 mm (4,0 - 16,0 inch) Lengte (één pagina) 101,6 - 558,8 mm (4,0 - 22,0 inch) Kopieën 1 origineel + maximaal 4 kopieën Dikte 0,065 - 0,39 mm (0,0025 - 0,015 inch) Gewicht (geen doorslagen) 52 - 82 g/m² (14 - 22 lb) Gewicht 40 - 58 g/m² (12 - 15 lb) (één vel van meerdere doorslagen) Inbinding Gelijmd met punten of gehecht aan beide zijkanten Etiketten: invoer onderzijde Etiketformaat minimaal 23,8 × 63,5 mm
Afdrukbaar gebied Losse vellen en enveloppen: Voor LX-300+II A De minimale bovenmarge is 4,2 mm (0,17 inch). B De minimale linker- en rechtermarge is 3,0 mm (0,12 inch) per marge. De maximum papierbreedte is 257 mm (10,1 inch) voor losse vellen. De maximaal afdrukbare breedte is 203,2 mm (8,0 inch). Als de papierbreedte aanmerkelijk breder is dan dit, zullen de zijmarges breder zijn dan het minimum maar is de afdrukbare breedte niet breder dan 203,2 mm (8,0 inch).
Voor LX-1170II A De minimale bovenmarge is 4,2 mm (0,17 inch). B De minimale linker- en rechtermarge is 3,0 mm (0,12 inch) per marge. De maximum papierbreedte is 420 mm (16,5 inch) voor losse vellen. De maximaal afdrukbare breedte is 345,44 mm (13,6 inch). Als de papierbreedte aanmerkelijk breder is dan dit, zullen de zijmarges breder zijn dan het minimum maar is de afdrukbare breedte niet breder dan 345,44 mm (13,6 inch). C 150 De minimale ondermarge is 4,2 mm (0,17 inch).
Kettingpapier Voor LX-300+II A De minimale marge boven en onder de perforatie is 4,2 mm (0,17 inch) per marge. B De minimale linker- en rechtermarge is 13 mm (0,51 inch) per marge. De maximale papierbreedte is 254 mm (10,0 inch). De maximaal afdrukbare breedte is 203,2 mm (8,0 inch). Als de papierbreedte aanmerkelijk breder is dan dit, zullen de zijmarges breder zijn dan het minimum maar is de afdrukbare breedte niet breder dan 203,2 mm (8,0 inch).
Voor LX-1170II A De minimale marge boven en onder de perforatie is 4,2 mm (0,17 inch) per marge. B De minimale linker- en rechtermarge is 13 mm (0,51 inch) per marge. De maximale papierbreedte is 406,4 mm (16,0 inch). De maximaal afdrukbare breedte is 345,44 mm (13,6 inch). Als de papierbreedte aanmerkelijk breder is dan dit, zullen de zijmarges breder zijn dan het minimum maar is de afdrukbare breedte niet breder dan 345,44 mm (13,6 inch). Papierrol: A De minimale bovenmarge is 4,2 mm (0,17 inch).
Papieruitlijning Afdrukken begint bij “0” op de schaal. Het niet-afdrukbare gebied ligt links van de “0.” Opdrachtenlijsten Uw printer biedt ondersteuning voor de onderstaande EPSON ESC/P 2-besturingscodes en IBM 2380 Plus (voor LX-300+II)/ IBM 2381 Plus (voor LX-1170II)-emulatiebesturingscodes. EPSON ESC/P-besturingscodes Door een EPSON ESC/P-printer te selecteren in uw software, kunt u geavanceerde lettertypen en afbeeldingen gebruiken.
Paginaformaat: ESC (C, ESC C, ESC C 0, ESC Q, ESC l, ESC (c, ESC N, ESC O, ESC (U Beweging afdrukpositie: ESC $, ESC \, ESC D, HT, ESC B, VT, ESC J Lettertypeselectie: ESC k, ESC x, ESC y, ESC P, ESC M, ESC g, ESC p, ESC 4, ESC 5, ESC E, ESC F, ESC ! Lettertypeverbetering: ESC W, DC4, SO, DC2, SI, ESC w, ESC G, ESC H, ESC T, ESC S, ESC Afstand: ESC Space Tekenverwerking: ESC t, ESC (t, ESC R, ESC %, ESC &, ESC :, ESC I, ESC 6, ESC 7 Bitmap: ESC K, ESC L, ESC Y, ESC Z, ESC *, ESC ^ Streepjescode: ESC (B Kleu
IBM 2380 Plus (voor LX-300+II)/ IBM 2381 Plus (voor LX-1170II)-emulatiebesturingscodes Deze printer emuleert de IBM Proprinter met gebruik van de onderstaande opdrachten. Raadpleeg de naslaghandleiding bij de IBM 2380 Plus (voor LX-300+II)/IBM 2381 Plus (voor LX-1170II) voor uitgebreide informatie.
Bitmap: ESC K, ESC L, ESC Y, ESC Z Streepjescode: ESC [f, ESC [p Downloaden: ESC = (alleen de modus Concept) Standaarden en goedkeuringen Veiligheidsgoedkeuringen (LX-300+II) 120 V-versie: Veiligheidsstandaarden UL60950 CSA60950 EMI FCC-artikel 15 subartikel B klasse B CAN/CSA - CEI/IEC CISPR22 klasse B 230 V-versie: Veiligheidsstandaarden EN60950 EMI AS/NZS CISPR22 klasse B (Beide modellen) 230 V-versie: Veiligheidsstandaarden 156 EN60950
EMC EN55022 klasse B EN61000-3-2 EN61000-3-3 EN55024 CE-markering (Beide modellen) 230 V-versie: Laagspanningsrichtlijn 73/23/EEC EN60950 EMC-richtlijn 89/336/EEC EN55022 klasse B EN61000-3-2 EN61000-3-3 EN55024 157
De printer reinigen U zorgt ervoor dat uw printer het beste blijft werken door deze enkele malen per jaar grondig te reinigen. Voer de volgende stappen uit om de printer te reinigen: 1. Verwijder het papier uit de printer. Zorg ervoor de printer uitstaat. 2. Verwijder de papiergeleider. Als een pull-tractor of een optionele invoer voor losse vellen is geïnstalleerd, verwijdert u deze. 3. Gebruik een zachte borstel om stof en vuil voorzichtig van de behuizing en papiergeleider te vegen. 4.
De printer vervoeren Als u de printer over enige afstand moet vervoeren, pakt u deze zorgvuldig in de originele doos met het originele verpakkingsmateriaal. Voer de volgende stappen uit om de printer in te pakken in de originele verpakking: w Waarschuwing: ❏ Wanneer u de printer vervoert, tilt u deze niet op aan de USB-kabelhouder omdat deze los kan raken en de printer kan vallen. Houd de linkeronderkant en de rechterkant van de printer goed vast om deze op te tillen.
Woordenlijst afdrukbaar gebied Het gedeelte van een pagina waarop de printer kan afdrukken. Vanwege de marges is dit kleiner dan de fysieke grootte van de pagina. afscheurpositie De positie waarnaar de printer het papier doorvoert als de modus voor automatisch afscheuren is ingeschakeld. Met de Micro Adjust-functie kunt u deze positie aanpassen, zodat de perforatie van het papier samenvalt met de afscheurrand van de printer.
concept De afdrukmodus die door de printer wordt gebruikt als u Draft selecteert als lettertype. Het lettertype Draft gebruikt minder punten per teken en drukt daardoor sneller af. Zie ook “snel concept”. dithering Een manier om punten op een pagina te plaatsen om zo een tint of toon te simuleren. dot-matrix Een afdrukmethode waarbij elke letter en elk symbool wordt gevormd door een patroon (matrix) van punten (dots). ESC/P Afkorting van EPSON Standard Code for Printers.
laadpositie De positie waarnaar het papier automatisch wordt geladen. near letter quality (NLQ) (bijna letterkwaliteit) De afdrukmodus die door de printer wordt gebruikt als een ander lettertype dan Draft is geselecteerd. Afdrukken met NLQ-lettertypen levert een mooier en beter leesbaar resultaat op bij een lagere afdruksnelheid. Zie ook “concept” en “snel concept”. opnieuw instellen De standaardinstellingen van de printer herstellen.
tekentabel Een verzameling letters, cijfers en symbolen die de tekenset vormen die in een bepaalde taal wordt gebruikt. tekens per inch (cpi) Een maateenheid voor de grootte van teksttekens. unidirectioneel afdrukken Bij deze afdrukinstelling drukt de printerkop af in slechts één richting. Unidirectioneel afdrukken is handig voor het afdrukken van afbeeldingen aangezien hierbij een nauwkeurige verticale uitlijning mogelijk is.
Index Numerieke tekens 0 slash (0 met schuine streep), 90 A Aanpassen papierdiktehendel, 37 Afdrukbaar gebied, 149 Afdrukken annuleren, 78 Afdrukrichting, 89 Afscheuren, 31 aanpassen, 32 automatisch, 32 knop, 31 Afscheurpositie aanpassen, 32 Auto CR (regelterugloop), 92 Auto I/F (interface) wait time (Automatische I/F (interface)-wachttijd), 90 Auto line feed (Automatische regeldoorvoer), 89 Auto tear-off (Automatisch afscheuren), 89 B Baud rate (Baudrate), 91 Bedieningspaneel, 84, 95 Bidirectioneel (Bi-d
E Emulatie, 155 Enveloppen afdrukken, 40 specificaties, 145, 147 EPSON Status Monitor 3, 41, 58 installeren, 61 instellen, 59 openen, 60 ESC/P, 153 Etiketten afdrukken, 39 specificaties, 146, 148 F Font (Lettertype), 92 Foutindicatie, 95 G Geïntegreerd lettertype lijst, 141 H High speed draft (Snel concept) (standaardinstelling), 90 I I/F (interface)-modus, 90 IBM 2380 Plus/IBM 2381 Plus-emulatie, 155 IBM-tekentabel standaardinstelling, 92 International character set for Italic table (Internationale tek
K Kettingpapier afdrukken, 16 specificaties, 145, 148 Klantenondersteuning, 118 Knoppen, 84 L Lampjes, 84 Lintcassette, 132, 140 Losse vellen afdrukken, 34 specificaties, 144, 146 M Manual feed wait time (Wachttijd voor handmatige invoer), 92 Meervoudige formulieren afdrukken, 38 specificaties, 145, 147 Micro adjust (Nauwkeurig aanpassen), 32 O Opties Kleurupgradekit, 128 Papierrolhouder, 126 P Packet mode (Pakketmodus), 91 Page length for tractor (Paginalengte voor kettingpapier), 88 Paneel, 84 Papierd
Positie bovenkant van formulier aanpassen Micro adjust (Nauwkeurig aanpassen), 28 Printer delen, 63 Printerde huidige printerdriver openen vanuit Windows Me of 98, 43 vanuit Windows XP, 2000 of Windows NT 4.
U Unidirectioneel (Uni-d) afdrukken, 89 USB-interface, 90 problemen, 111 V Verticale regels uitlijnen, 115 Verwijderen afgedrukt document uit push-tractor, 20 printersoftware, 79 Stuurprogramma van USB-apparaat, 81 Z Zelftest, 115 168