® Benutzerhandbuch NPDxxxx-00
Copyright und Marken Copyright Kein Teil dieses Handbuchs darf in irgendeiner Form (Druck, Fotokopie, Mikrofilm oder ein anderes Verfahren) ohne die schriftliche Genehmigung der Seiko Epson Corporation reproduziert oder unter Verwendung elektronischer Systeme verarbeitet, vervielfältigt oder verbreitet werden. Die hierin enthaltenen Informationen sind ausschließlich für diesen Epson-Drucker bestimmt. Epson haftet nicht für die Anwendung dieser Informationen auf andere Drucker.
IBM® ist eine eingetragene Marke der International Business Machines Corporation. Allgemeiner Hinweis: Alle im Handbuch genannten Bezeichnungen von Erzeugnissen sind Marken der jeweiligen Firmen. Aus dem Fehlen der Markenzeichen (R) bzw. TM kann nicht geschlossen werden, dass die Bezeichnung ein freier Markenname ist. Copyright © 2006 Seiko Epson Corporation. Alle Rechte vorbehalten.
Sicherheitshinweise Handbuch-Konventionen w c Vorsicht Diese Warnungen müssen unbedingt beachtet werden, um Körperverletzungen zu vermeiden. Achtung Anmerkungen dieser Art müssen beachtet werden, um Schäden am Gerät zu vermeiden. Hinweise Hinweise enthalten wichtige Informationen und hilfreiche Tipps zur Arbeit mit dem Drucker. Warnsymbol „Heiße Teile“ K Dieses Symbol befindet sich am Druckkopf und anderen Teilen und weist darauf hin, dass diese heiß sein können.
❏ Stellen Sie dieses Produkt nicht auf eine weiche, instabile Fläche wie beispielsweise ein Bett oder ein Sofa oder in einen beengten, abgeschlossenen Bereich, da hierdurch die Belüftung behindert wird. ❏ Achten Sie darauf, dass die Lüftungsöffnungen am Druckergehäuse nicht verdeckt sind. Führen Sie keine Gegenstände durch die Öffnungen ein. ❏ Die verwendete Netzspannung muss mit der auf dem Typenschild des Druckers angegebenen Betriebsspannung übereinstimmen.
Warten des Druckers ❏ Trennen Sie den Drucker vor der Reinigung von der Stromversorgung, und reinigen Sie ihn mit einem feuchten Tuch. Verwenden Sie keine Flüssigreiniger oder Reinigungssprays. ❏ Achten Sie darauf, dass keine Flüssigkeit in den Drucker gelangt. ❏ Mit Ausnahme der ausdrücklich in diesem Handbuch angegebenen Handgriffe sollten Sie niemals versuchen, das Gerät selbst zu reparieren. Sämtliche Wartungsarbeiten sollten nur von autorisiertem Fachpersonal vorgenommen werden.
Umgang mit Papier ❏ Da Etiketten empfindlich gegenüber Temperaturschwankungen und Luftfeuchtigkeit sind, verwenden Sie sie nur unter den nachfolgend beschriebenen Betriebsbedingungen: Temperatur: 15 bis 25°C (59 bis 77°F) Relative Luftfeuchtigkeit: 30-60 % ❏ Lassen Sie zwischen den Druckaufträgen keine Etiketten im Drucker, da diese sich um die Druckwalze legen und einen Papierstau verursachen können, wenn Sie erneut drucken. ❏ Legen Sie kein gewelltes oder geknicktes Papier ein.
Für Benutzer in Großbritannien Verwendung des Zubehörs Epson (UK) Limited kann nicht für Schäden oder sonstige Probleme haftbar gemacht werden, die aus der Verwendung von Zubehör oder Verbrauchsmaterial resultieren, das weder von Epson hergestellt noch von Epson (UK) Limited für den Gebrauch mit Epson-Geräten zugelassen wurde. Sicherheitsinformationen w Vorsicht: Dieses Gerät muss geerdet werden.
Wenn der Stecker beschädigt wird, ersetzen Sie das gesamte Netzkabel, oder wenden Sie sich an einen qualifizierten Elektriker. Tauschen Sie Sicherungen nur gegen Sicherungen der korrekten Größe und Amperezahl aus. Informationen für Benutzer in Großbritannien, Singapur und Hongkong Tauschen Sie Sicherungen nur gegen Sicherungen der korrekten Größe und Amperezahl aus. Sicherheitsanforderungen Netzstecker: Verwenden Sie einen von der Safety Authority zugelassenen Dreistiftstecker.
Inhalt Copyright und Marken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marken . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handbuch-Konventionen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnsymbol „Heiße Teile“ . . .
Druckersoftware Informationen zur Druckersoftware. . . . . . . . . . . . . . . . . . . . . . . . . .38 Verwenden des Druckertreibers unter Windows Me und 98. . . . .39 Zugreifen auf den Druckertreiber über eine Windows-Anwendung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Zugreifen auf den Druckertreiber über das Startmenü . . . . .42 Ändern der Druckertreibereinstellungen . . . . . . . . . . . . . . . . .43 Verwenden des Druckertreibers unter Windows XP, 2000 und Windows NT 4.0 . . .
Fehlerbehebung Verwenden der Fehleranzeigen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Probleme und Lösungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Stromversorgung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Druckvorgang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Handhabung der Druckmedien . . . . . . . . . . . . . . . . . . . . . . . 101 Optionen . . . . . . . . . . . . . . . . . . . .
Befehlslisten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 EPSON ESC/P-Steuercodes . . . . . . . . . . . . . . . . . . . . . . . . . . .149 IBM 2380 Plus-Emulationssteuercode (für LX-300+II)/ IBM 2381 Plus-Emulationssteuercode (für LX-1170II) . . . . .151 Normen und Richtlinien. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Sicherheitsrichtlinien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 CE-Siegel . . . . . .
Informationen zum Drucker Funktionen Die 9-Nadel-Matrixdrucker „EPSON® LX-300+II/LX-1170II“ verfügen über ein kompaktes Design und ermöglichen Ausdrucke von hoher Qualität. Folgende Funktionen gehören zum Leistungsumfang: ❏ Verschiedene Papierführungen für unterschiedliche Druckanforderungen. ❏ Kompatibilität mit einer Vielzahl von Papiersorten, wie z. B. Endlospapier, Mehrfachformulare (mit einem Original und bis zu vier Durchschlägen), Etiketten, Einzelblattpapier und Briefumschläge.
Handhabung der Druckmedien Drucken auf Endlospapier Zur Aufnahme von Endlospapier wird der Traktor des Druckers verwendet. Je nach Positionierung des Traktors kann dieser als Zugtraktor oder Schubtraktor verwendet werden.
Hinweis: Die Abbildungen in diesem Handbuch beziehen sich auf den LX-300+II. Der LX-1170II ist breiter als der LX-300+II. Die Erläuterungen gelten jedoch für beide Modelle. Gehen Sie folgendermaßen vor, um Endlospapier mit dem Schubtraktor zu laden: 1. Stellen Sie sicher, dass der Drucker ausgeschaltet ist. Entfernen Sie die Druckerabdeckung und die Papierführung, und stellen Sie den Papierwahlhebel auf die Position für Endlospapier. 2.
3. Verschieben Sie die linke Stachelradeinheit mithilfe der Markierungen am Drucker in die gewünschte Position. Der Druck beginnt rechts von der Position 0. Drücken Sie den Verriegelungshebel der Stachelradführung zurück, um die Stachelradführung zu verriegeln. Verschieben Sie dann die rechte Stachelradeinheit in eine Position entsprechend der Papierbreite, verriegeln Sie diese jedoch nicht. Verschieben Sie die Papierstütze, bis sie sich in der Mitte zwischen beiden Stachelradeinheiten befindet. 4.
5. Um das einzuziehende Papier vom bedruckten Papier zu trennen, bringen Sie die Papierführung an, indem Sie sie horizontal halten und die Kerben an den Befestigungszapfen des Druckers wie unten dargestellt ausrichten. Schieben Sie dann die Papierführung in Richtung der Druckervorderseite, bis sie spürbar einrastet, und stellen Sie die Papierführungsschienen entsprechend der Papierbreite ein. 6. Schalten Sie den Drucker ein. 7. Stellen Sie sicher, dass die Druckerabdeckung geschlossen ist.
Entfernen eines gedruckten Dokuments aus dem Schubtraktor Gehen Sie folgendermaßen vor, um das gedruckte Dokument zu entfernen: 1. Drücken Sie die Taste Tear Off (Font) (Abtrennen (Schriftart)). Stellen Sie sicher, dass die Anzeige Tear Off (Font) (Abtrennen (Schriftart)) blinkt. (Dadurch wird angezeigt, dass sich das Papier in der richtigen Position zum Abtrennen befindet.) 2. Öffnen Sie die Abdeckung der Papierführung, und trennen Sie das gedruckte Dokument über der Abtrennkante der Papierspanneinheit ab.
3. Schließen Sie die Abdeckung der Papierführung. Wenn Sie den Druckvorgang fortsetzen, transportiert der Drucker das Papier automatisch zurück in die Druckstartposition und startet den Druckvorgang. Drücken Sie die Taste Load/Eject (Laden/Auswerfen), um Endlospapier in die Bereitschaftsposition zu transportieren, in der Sie das Papier entfernen können. Öffnen Sie dann die Stachelradabdeckungen des Traktors, und entfernen Sie das Papier.
c Achtung: ❏ Verwenden Sie den Papierzufuhrknopf auf der rechten Seite des Druckers nur, um im ausgeschalteten Zustand Papierstaus zu beseitigen. Andernfalls kann der Drucker beschädigt oder die Druckstartposition verstellt werden. ❏ Stellen Sie beim Drucken mit dem Zugtraktor die Abtrennautomatik im Modus Standardeinstellung auf Aus. Andernfalls können Papierstaus verursacht werden. 1. Schalten Sie den Drucker aus, und entfernen Sie die Abdeckung des Druckers und die Papierführung.
2. Drücken Sie vorsichtig auf die Verriegelungsstifte auf beiden Seiten des Traktors, drehen Sie ihn nach oben, und ziehen Sie ihn aus dem Drucker heraus. 3. Halten Sie den Traktor über den Montageeinschub an der Oberseite des Druckers, und kippen Sie ihn wie unten dargestellt in die richtige Position. Drücken Sie den Traktor mit den Kerben auf die Befestigungszapfen, bis er spürbar einrastet. 4. Lösen Sie die Stachelradeinheiten, indem Sie die Stachelradverriegelungen nach vorne ziehen.
5. Legen Sie das Papier in den unteren oder den hinteren Papierschacht wie unten dargestellt ein, und ziehen Sie es nach oben. Positionieren Sie das Papier mithilfe der Markierung am Drucker. Der Druck beginnt rechts von der Position 0. 6. Verschieben Sie die linke Stachelradeinheit, bis die Stachelräder mit den Transportlöchern des Papiers übereinstimmen, und verriegeln Sie die Einheit in dieser Position.
Hinweis: Wenn erforderlich, spannen Sie das Papier nach, indem Sie es vorsichtig von hinten oder unten ziehen. 8. Bringen Sie die Papierführung an, um das einzuziehende Papier vom bedruckten Papier zu trennen. Halten Sie die Papierführung horizontal, und richten Sie die Kerben an den Befestigungszapfen des Druckers aus. Schieben Sie dann die Papierführung in Richtung der Rückseite des Druckers, bis sie spürbar einrastet, und stellen Sie die Papierführungsschienen entsprechend der Papierbreite ein. 9.
Einstellen der Druckstartposition Die Druckstartposition ist die Position auf dem Blatt, an der der Drucker den Druckvorgang beginnt. Wenn der Druck zu weit oben oder unten positioniert ist, können Sie die Druckstartposition mit der Mikroeinstellung ändern. Führen Sie folgende Anweisungen aus: c Achtung: Verwenden Sie niemals den Papierzufuhrknopf, um die Druckstartposition einzustellen. Dadurch kann der Drucker beschädigt oder die Druckstartposition verstellt werden.
5. Drücken Sie die Taste LF/FF D (Zeilen-/Seitenvorschub), um die Druckstartposition auf der Seite nach oben zu verschieben, oder drücken Sie die Taste Load/Eject U (Laden/Auswerfen), um die Druckstartposition auf der Seite nach unten zu verschieben. * * Plastikabdeckung des Farbbands Hinweis: ❏ Der Drucker hat vorgegebene Grenzwerte für die Druckstartposition.
In folgendem Beispiel wird erläutert, wie Sie die Druckstartposition für Endlospapier einstellen, das mit dem Zugtraktor geladen wird. Markieren Sie zuerst einen Punkt 2,5 mm (0,1 Zoll) über der Perforierung auf dem Papier, und positionieren Sie das Papier so, dass die Markierung mit der oberen Kante der Plastikabdeckung des Farbbands übereinstimmt. So erhalten Sie auf der nächsten Seite einen Rand von 8,5 mm (0,33 Zoll), d. h., der Druck beginnt 8,5 mm (0,33 Zoll) unterhalb der Perforierung.
Transportieren des Papiers zur Abtrennkante Wenn Sie den Schubtraktor verwenden, können Sie das Endlospapier nach Abschluss des Druckvorgangs mithilfe der Abtrennfunktion zur Abtrennkante des Druckers transportieren. So können Sie das gedruckte Dokument auf einfache Weise abtrennen. Wenn Sie den Druckvorgang fortsetzen, transportiert der Drucker das Papier automatisch zurück in die Druckstartposition, damit auch das Papier zwischen gedruckten Dokumenten genutzt wird.
Automatisches Transportieren von Papier in die Abtrennposition Um gedruckte Dokumente automatisch in die Abtrennposition zu transportieren, muss die Abtrennautomatik aktiviert und die entsprechende Seitenlänge für Endlospapier im Modus Standardeinstellung ausgewählt sein. Anweisungen hierzu finden Sie unter „Ändern von Standardeinstellungen“.
3. Halten Sie die Taste Pause für ungefähr drei Sekunden gedrückt. Die Anzeige Pause beginnt zu blinken, und der Drucker wird in den Mikroeinstellungsmodus versetzt. 4. Drücken Sie die Taste LF/FF D (Zeilen-/Seitenvorschub), um das Papier rückwärts zu transportieren bzw. die Taste Load/Eject U (Laden/Auswerfen), um das Papier vorwärts zu transportieren, bis die Perforierung des Papiers an der Abtrennkante ausgerichtet ist.
Drucken auf Einzelblattpapier Mithilfe der Papierführung des Druckers können Sie Einzelblattpapier blattweise in den Drucker einlegen. Ausführliche Angaben zu den Einzelblattpapiersorten, die Sie verwenden können, finden Sie unter „Papier“. Vergewissern Sie sich vor dem Bedrucken von Einzelblatt-Mehrfachformularen, Briefumschlägen oder anderen Spezialpapiersorten, dass sich der Papierstärkehebel in der entsprechenden Position befindet. Weitere Informationen finden Sie unter „Drucken auf Spezialpapier“.
Einlegen von einzelnen Blättern Gehen Sie folgendermaßen vor, um einzelne Blättern einzulegen: 1. Stellen Sie sicher, dass der Drucker ausgeschaltet ist. Vergewissern Sie sich außerdem, dass sich der Papierwahlhebel in der Einzelblattposition und die Papierführung in aufrechter Position befinden. 2. Verschieben Sie die linke Papierführungsschiene, bis sie in der markierten Position einrastet. Verschieben Sie dann die rechte Papierführungsschiene entsprechend der Papierbreite.
3. Legen Sie ein Blatt Papier zwischen den Papierführungsschienen bis zum Anschlag ein. Für den normalen Gebrauch schalten Sie den Drucker ein, ohne weitere Tasten zu drücken. Sobald der Drucker Daten empfängt, beginnt der Druckvorgang. c Achtung: Verwenden Sie den Papierzufuhrknopf auf der rechten Seite des Druckers nur, um im ausgeschalteten Zustand Papierstaus zu beseitigen. Andernfalls kann der Drucker beschädigt oder die Druckstartposition verstellt werden.
Einstellen des Papierstärkehebels Bevor Sie auf Spezialpapier drucken können, muss der Papierstärkehebel entsprechend eingestellt werden. Führen Sie zum Einstellen des Papierstärkehebels die folgenden Anweisungen aus: 1. Schalten Sie den Drucker aus, und öffnen Sie die Druckerabdeckung. Der Papierstärkehebel befindet sich auf der linken Seite des Druckers. Die Zahlen neben dem Hebel geben die eingestellte Papierstärke an. 2. Wählen Sie anhand folgender Tabelle die entsprechende Papierstärke aus.
Mehrfachformulare Sie können Mehrfachformulare ohne Kohlebeschichtung aus Einzelblatt- oder Endlospapier mit bis zu vier Lagen (das Original und drei Kopien) verwenden. Stellen Sie vor dem Drucken den Papierstärkehebel in die entsprechende Position, wie im vorigen Abschnitt beschrieben. Mit folgenden Hinweisen erzielen Sie ein optimales Druckergebnis: ❏ Verwenden Sie ausschließlich Endlosmehrfachformulare, die durch Punktklebung oder seitliche Crimplock-Heftung zusammengefügt sind.
Etiketten Um Etiketten zu bedrucken, müssen Sie den Traktor als Zugtraktor verwenden und Papier über den unteren Papierschacht zuführen. Stellen Sie den Papierstärkehebel auf die entsprechende Position für den Etikettendruck, wie in Abschnitt „Einstellen des Papierstärkehebels“ beschrieben. Beachten Sie folgende Hinweise: ❏ Verwenden Sie Etiketten, die auf Endlospapier mit Transportlöchern für einen Traktor aufgeklebt sind.
Briefumschläge In der Papierführung können einzelne Briefumschläge eingelegt werden. Beachten Sie folgende Hinweise: ❏ Stellen Sie vor dem Drucken von Briefumschlägen den Papierstärkehebel auf die entsprechende Position. Weitere Informationen finden Sie unter „Einstellen des Papierstärkehebels“. ❏ Führen Sie die Anweisungen unter „Einlegen von einzelnen Blättern“ aus, um einen Briefumschlag einzulegen. Legen Sie den Briefumschlag mit der breiten Kante zuerst und der bedruckbaren Seite nach unten ein.
Druckersoftware Informationen zur Druckersoftware Die Epson-Software beinhaltet die Druckertreiber-Software sowie EPSON Status Monitor 3. Der Druckertreiber ist ein Programm, das der Computer zur Steuerung des Druckers benötigt. Der Druckertreiber muss installiert werden, damit Softwareanwendungen unter Windows die Möglichkeiten des Druckers vollständig nutzen können.
Verwenden des Druckertreibers unter Windows Me und 98 Der Druckertreiber kann aus Windows-Anwendungen oder direkt über das Windows-Startmenü aufgerufen werden. ❏ Wenn Sie den Druckertreiber aus einer Windows-Anwendung aufrufen, gelten alle Einstellungen, die Sie vornehmen, nur für diese Anwendung. Weitere Informationen finden Sie unter „Zugreifen auf den Druckertreiber über eine Windows-Anwendung“.
Zugreifen auf den Druckertreiber über eine Windows-Anwendung Führen Sie die folgenden Schritte aus, um den Druckertreiber aus einer Windows-Anwendung aufzurufen: 1. Wählen Sie im Menü Datei Ihrer Anwendung den Befehl Drucker einrichten oder Drucken aus. Sobald das Dialogfeld Drucken oder Drucker einrichten angezeigt wird, vergewissern Sie sich, dass Ihr Drucker in der Dropdownliste Name ausgewählt ist.
2. Klicken Sie auf Drucker, Einrichten, Eigenschaften oder Optionen. (Welche dieser Schaltflächen angezeigt wird, ist abhängig von der jeweiligen Anwendung. Unter Umständen müssen Sie auf eine Kombination der genannten Schaltflächen klicken.) Das Fenster Eigenschaften mit den Menüs Papier, Grafik und Geräteoptionen wird angezeigt. Auf diesen Registerkarten finden Sie die Druckertreibereinstellungen. 3. Klicken Sie zum Anzeigen eines Menüs auf die entsprechende Registerkarte am oberen Rand des Fensters.
Zugreifen auf den Druckertreiber über das Startmenü Führen Sie diese Schritte aus, um über das Startmenü auf den Druckertreiber zuzugreifen: 1. Klicken Sie auf die Schaltfläche Start, und zeigen Sie dann auf Einstellungen. 2. Klicken Sie auf Drucker. 3. Klicken Sie mit der rechten Maustaste auf das Symbol für Ihren Drucker, und klicken Sie dann auf Eigenschaften. Auf dem Bildschirm wird das Dialogfeld Eigenschaften mit den Registerkarten Papier, Grafik, Geräteoptionen und Utility angezeigt.
Ändern der Druckertreibereinstellungen Der Druckertreiber enthält sieben Menüs: Papier, Grafik, Geräteoptionen, Allgemein, Details, Utility und Freigabe. Einen Überblick über die verfügbaren Einstellungen finden Sie unter „Übersicht über die Druckertreibereinstellungen“. Zusätzlich können Sie die Onlinehilfe aufrufen, indem Sie mit der rechten Maustaste auf Elemente im Druckertreiber klicken und die Option Direkthilfe auswählen.
Verwenden des Druckertreibers unter Windows XP, 2000 und Windows NT 4.0 Der Druckertreiber kann aus Windows-Anwendungen oder direkt über das Windows-Startmenü aufgerufen werden. ❏ Wenn Sie den Druckertreiber aus einer Windows-Anwendung aufrufen, gelten alle Einstellungen, die Sie vornehmen, nur für diese Anwendung. Weitere Informationen finden Sie unter „Zugreifen auf den Druckertreiber über eine Windows-Anwendung“.
Zugreifen auf den Druckertreiber über eine Windows-Anwendung Führen Sie die folgenden Schritte aus, um den Druckertreiber aus einer Windows-Anwendung aufzurufen: Hinweis: Die im folgenden Abschnitt aufgeführten Beispiele beziehen sich auf das Betriebssystem Windows 2000. Die Darstellung unterscheidet sich möglicherweise von den tatsächlichen Bildschirmanzeigen. Die Anweisungen sind jedoch dieselben. 1. Wählen Sie im Menü Datei Ihrer Anwendung den Befehl Drucker einrichten oder Drucken aus.
2. Klicken Sie auf Drucker, Einrichten, Eigenschaften oder Optionen. (Welche dieser Schaltflächen angezeigt wird, ist abhängig von der jeweiligen Anwendung. Unter Umständen müssen Sie auf eine Kombination der genannten Schaltflächen klicken.) Das Fenster Dokumenteigenschaften mit den Menüs Layout und Papier/Qualität wird angezeigt. Auf diesen Registerkarten finden Sie die Druckertreibereinstellungen.
3. Klicken Sie zum Anzeigen eines Menüs auf die entsprechende Registerkarte am oberen Rand des Fensters. Weitere Informationen zum Ändern der Druckertreibereinstellungen finden Sie unter „Ändern der Druckertreibereinstellungen“.
Zugreifen auf den Druckertreiber über das Startmenü Führen Sie diese Schritte aus, um über das Startmenü auf den Druckertreiber zuzugreifen: Hinweis: Die folgenden Bildschirmanzeigen dieses Verfahrens beziehen sich auf das Betriebssystem Windows 2000. Die Darstellung unterscheidet sich möglicherweise von den tatsächlichen Bildschirmanzeigen. Die Anweisungen sind jedoch dieselben. 1. Klicken Sie auf die Schaltfläche Start, und zeigen Sie dann auf Einstellungen. 2. Klicken Sie auf Drucker. 3.
Klicken Sie mit der rechten Maustaste auf das Druckersymbol, und klicken Sie dann auf Eigenschaften, um das Fenster Eigenschaften mit den Menüs anzuzeigen, in denen Sie die Einstellungen des Druckertreibers vornehmen können. 4. Klicken Sie zum Anzeigen eines Menüs auf die entsprechende Registerkarte am oberen Rand des Fensters. Weitere Informationen zum Ändern der Einstellungen finden Sie unter „Übersicht über die Druckertreibereinstellungen“.
Wenn Sie alle Druckertreibereinstellungen vorgenommen haben, klicken Sie auf OK, um die Einstellungen zu übernehmen, oder klicken Sie auf Abbrechen, um die Änderungen rückgängig zu machen. Sobald Sie die Einstellungen des Druckertreibers überprüft und ggf. angepasst haben, können Sie mit dem Drucken beginnen. Übersicht über die Druckertreibereinstellungen Die folgenden Tabellen enthalten eine Übersicht über die Einstellungen des Druckertreibers unter Windows.
Einstellungen Erklärungen Druckqualität Wählen Sie eine Option für die Druckqualität aus der Liste aus. Wenn Sie die Option Schnell aktivieren, wechselt der Drucker in den bidirektionalen Druckmodus mit höherer Druckgeschwindigkeit. Wenn Sie die Option Schnell deaktivieren, wechselt der Drucker in den unidirektionalen Druckmodus. Dadurch wird die Druckgeschwindigkeit verringert, die Präzision des Drucks erhöht sich jedoch.
Einstellungen Erklärungen Seiten pro Blatt* Geben Sie ein, wie viele Seiten auf einem Blatt gedruckt werden sollen. Exemplare zählen* Wenn Sie im Feld Anzahl Exemplare einen höheren Wert als 1 auswählen, wird dieses Kontrollkästchen angezeigt, und Sie können auswählen, ob die Seiten der Exemplare sortiert werden sollen. Erweiterte Druckfunktionen* Wählen Sie Aktivieren oder Deaktivieren für Metafile Spooling aus.
Benutzerdefiniertes Papierformat Wenn ein gewünschtes Papier nicht in der Dropdownliste Papierformat enthalten ist, können Sie das Format zur Liste hinzufügen. Windows Me und 98: Klicken Sie auf Benutzerdefiniert oder Benutzerdefinierte Größe, und geben Sie das Papierformat in das angezeigte Dialogfeld ein. Windows XP, 2000 und Windows NT 4.0: 1. Klicken Sie unter Windows 2000 oder Windows NT 4.0 auf Start, zeigen Sie auf Einstellungen, und klicken Sie auf Drucker.
Überwachungseinstellungen Einstellungen Erklärungen EPSON Status Monitor 3 Sie können den EPSON Status Monitor 3 durch Klicken auf diese Schaltfläche aufrufen. Wenn der Drucker überwacht werden soll, muss das Kontrollkästchen Druckstatus überwachen aktiviert sein. Überwachungsoptionen Klicken Sie auf diese Schaltfläche, um das Dialogfeld Überwachungsoptionen zu öffnen. In diesem Dialogfeld können Sie Einstellungen für den EPSON Status Monitor 3 vornehmen.
Hinweis: Wenn Sie den Treiber mit der Methode „Point and Print“ installieren, funktioniert EPSON Status Monitor 3 möglicherweise nicht einwandfrei. Wenn Sie EPSON Status Monitor 3 verwenden möchten, installieren Sie den Treiber neu, wie auf dem Blatt „Hier starten“ beschrieben. Lesen Sie vor der Verwendung von EPSON Status Monitor 3 die Datei README auf der Benutzer-CD-ROM. Diese Datei enthält die neuesten Informationen zum Utility.
2. Klicken Sie auf die Schaltfläche Überwachungsoptionen. Das Dialogfeld Überwachungsoptionen wird angezeigt. 3. Die folgenden Einstellungen sind verfügbar: Mitteilung auswählen Zeigt den Status Ein/Aus des Kontrollkästchens für die Fehlermeldung an. Aktivieren Sie dieses Kontrollkästchen, um die ausgewählte Fehlermeldung anzuzeigen. 56 Shortcut-Symbol auswählen Das ausgewählte Symbol wird in der Taskleiste angezeigt. Im rechten Fenster wird eine Vorschau der gewählten Einstellung angezeigt.
Hinweis: Klicken Sie auf die Schaltfläche Standard, um die Standardeinstellungen für alle Optionen wiederherzustellen. Aufrufen von EPSON Status Monitor 3 Wählen Sie eine der folgenden Methoden zum Aufrufen von EPSON Status Monitor 3: ❏ Doppelklicken Sie auf das Druckersymbol in der Taskleiste. Um der Taskleiste ein Shortcut-Symbol hinzuzufügen, rufen Sie das Menü Utility auf, und folgen Sie den Anweisungen.
Installieren von EPSON Status Monitor 3 Gehen Sie folgendermaßen vor, um EPSON Status Monitor 3 zu installieren. 1. Stellen Sie sicher, dass der Drucker ausgeschaltet ist und Windows auf dem Computer ausgeführt wird. 2. Legen Sie die CD-ROM mit der Druckersoftware in das CD-ROM-Laufwerk ein. Hinweis: ❏ Wenn das Fenster zur Auswahl der Sprache angezeigt wird, wählen Sie Ihr Land aus.
Einbinden des Druckers in ein Netzwerk Freigeben des Druckers In diesem Abschnitt wird die Druckerfreigabe in einem normalen Windows-Netzwerk beschrieben. Ein Drucker kann von allen Computern in einem Netzwerk verwendet werden, wenn er an einen der Computer direkt angeschlossen ist. Der Computer, an dem der Drucker direkt angeschlossen ist, wird als Druckerserver bezeichnet. Die anderen Computer sind Clients, die eine Berechtigung benötigen, um den Drucker mit dem Druckerserver gemeinsam zu verwenden.
❏ Informationen zu Windows NT 4.0 finden Sie unter „Windows NT 4.0“. Hinweis: ❏ Richten Sie EPSON Status Monitor 3 für die Freigabe des Druckers so ein, dass der freigegebene Drucker auf dem Druckerserver überwacht werden kann. Weitere Informationen finden Sie unter „Einrichten von EPSON Status Monitor 3“.
3. Klicken Sie im unter Konfiguration auf Datei- und Druckerfreigabe. 4. Aktivieren Sie das Kontrollkästchen Anderen Benutzern soll der Zugriff auf meine Drucker ermöglicht werden können., und klicken Sie auf OK. 5. Klicken Sie auf OK, um die Einstellungen zu übernehmen. Hinweis: ❏ Wenn Sie zum Einlegen eines Datenträgers aufgefordert werden, legen Sie die CD-ROM mit Windows Me bzw. 98 in das CD-ROM-Laufwerk des Computers ein. Klicken Sie auf OK, und folgen Sie den Anweisungen am Bildschirm.
8. Wählen Sie Freigegeben als, geben Sie im Feld Freigabename den Namen ein, und klicken Sie auf OK. Geben Sie, wenn gewünscht, einen Kommentar oder ein Kennwort ein. Hinweis: ❏ Verwenden Sie keine Leerzeichen oder Bindestriche im Freigabenamen, da dies zu Fehlern führt. ❏ Richten Sie EPSON Status Monitor 3 für die Freigabe des Druckers so ein, dass der freigegebene Drucker auf dem Druckerserver überwacht werden kann. Weitere Informationen finden Sie unter „Einrichten von EPSON Status Monitor 3“.
Windows XP, 2000 oder Windows NT 4.0 Wenn auf dem Druckerserver Windows XP, 2000 oder Windows NT 4.0 installiert ist, gehen Sie zum Einrichten des Druckerservers folgendermaßen vor. Hinweis: Sie müssen sich unter Windows XP, 2000 und Windows NT 4.0 als Administrator auf dem lokalen Computer anmelden. 1. Bei einem Druckerserver mit Windows 2000 oder Windows NT 4.0 klicken Sie auf Start, zeigen Sie auf Einstellungen, und klicken Sie dann auf Drucker.
3. Wählen Sie bei einem Druckerserver mit Windows 2000 oder Windows NT 4.0 Freigegeben als (Windows 2000) bzw. Freigegeben (Windows NT 4.0) aus, geben Sie den Namen in das Feld Freigabename ein, und klicken Sie auf OK. Wählen Sie bei einem Druckerserver mit Windows XP Drucker freigeben aus, geben Sie den Namen im Feld Freigabename ein, und klicken Sie auf OK. Hinweis: Verwenden Sie keine Leerzeichen oder Bindestriche im Freigabenamen, da dies zu Fehlern führt.
Einstellung für die Clients In diesem Abschnitt wird beschrieben, wie Sie in einem Netzwerk auf den freigegebenen Drucker zugreifen und den erforderlichen Druckertreiber installieren. Hinweis: ❏ Zur Freigabe des Druckers in einem Windows-Netzwerk müssen Sie den Druckerserver einrichten. Weitere Informationen finden Sie unter „Einrichten des Druckers als freigegebener Drucker“ (Windows Me oder 98) bzw. „Windows XP, 2000 oder Windows NT 4.0“ (Windows XP, 2000 oder Windows NT 4.0).
3. Wählen Sie Netzwerkdrucker aus, und klicken Sie auf Weiter. 4. Klicken Sie auf Durchsuchen. Das Dialogfeld Drucker suchen wird angezeigt. Hinweis: Sie können als Netzwerkpfad oder Warteschlangennamen auch „\\(Name des Computers, der lokal mit dem freigegebenen Drucker verbunden ist)\(Name des freigegebenen Druckers)“ eingeben. 5. Klicken Sie auf den Computer oder Server, der mit dem freigegebenen Drucker verbunden ist, und dann auf den Namen des freigegebenen Druckers. Klicken Sie auf OK.
❏ Wenn der Druckerserver unter Windows Me oder 98 ausgeführt wird, fahren Sie mit dem nächsten Schritt fort. ❏ Wenn auf dem Druckerserver nicht Windows Me oder 98 installiert ist, fahren Sie mit „Installieren der Druckersoftware von CD-ROM“ fort. 7. Überprüfen Sie den Namen des freigegebenen Druckers, und geben Sie an, ob der Drucker als Standarddrucker verwendet werden soll. Klicken Sie auf OK, und folgen Sie den Anweisungen am Bildschirm.
Klicken Sie unter Windows XP im Menü Druckeraufgaben auf Drucker hinzufü.gen. 3. Wählen Sie unter Windows 2000 die Option Netzwerkdrucker oder unter Windows XP die Option Netzwerkdrucker oder Drucker, der an einen anderen Computer angeschlossen ist aus, und klicken Sie auf Weiter. 4. Unter Windows 2000 wählen Sie Druckernamen eingeben oder auf „Weiter“ klicken, um nach dem Drucker zu suchen, und klicken Sie dann auf Weiter.
Wählen Sie unter Windows XP Drucker suchen, und klicken Sie dann auf Weiter. 5. Klicken Sie auf das Symbol für den Computer oder Server, der mit dem freigegebenen Drucker verbunden ist, und anschließend auf den Namen des freigegebenen Druckers. Klicken Sie dann auf Weiter. Hinweis: ❏ Der Name des freigegebenen Druckers kann über den Computer oder Server, an den der Drucker angeschlossen ist, geändert werden. Den Namen des freigegebenen Druckers können Sie beim Netzwerkadministrator erfragen.
❏ Wenn der Druckertreiber bereits auf dem Client installiert wurde, müssen Sie den neuen oder den aktuell installierten Druckertreiber auswählen. Wenn Sie zur Auswahl des Druckertreibers aufgefordert werden, wählen Sie den Druckertreiber entsprechend der Meldung aus. ❏ Wenn auf dem Druckerserver Windows XP oder 2000 installiert ist, fahren Sie mit dem nächsten Schritt fort.
Windows NT 4.0 Führen Sie zum Einrichten von Windows NT 4.0-Clients die folgenden Schritte aus. Zur Installation des Druckertreibers für den freigegebenen Drucker müssen Sie als Hauptbenutzer angemeldet sein oder über weitergehende Zugriffsrechte verfügen. Administratorrechte sind nicht unbedingt erforderlich. 1. Klicken Sie auf Start, zeigen Sie auf Einstellungen, und klicken Sie anschließend auf Drucker. 2. Doppelklicken Sie auf das Symbol Drucker hinzufügen. 3.
Hinweis: ❏ Sie können als Netzwerkpfad oder Warteschlangennamen auch „\\(Name des Computers, der lokal mit dem freigegebenen Drucker verbunden ist)\(Name des freigegebenen Druckers)“ eingeben. ❏ Der Name des freigegebenen Druckers kann über den Computer oder Server, an den der Drucker angeschlossen ist, geändert werden. Den Namen des freigegebenen Druckers können Sie beim Netzwerkadministrator erfragen.
Hinweis: ❏ Bei der Installation auf Clients unter Windows XP, 2000 oder Windows NT 4.0 müssen Sie sich auf diesen Betriebssystemen als Administrator anmelden. ❏ Wenn die Server- und Clientcomputer dasselbe Betriebssystem verwenden, müssen Sie die Druckertreiber nicht von CD-ROM installieren. 1. Wenn Sie auf den freigegebenen Drucker zugreifen, wird eventuell eine Meldung angezeigt. Klicken Sie auf OK, und folgen Sie zur Installation des Druckertreibers von CD-ROM den Anweisungen am Bildschirm. 2.
Je nach Betriebssystem werden unterschiedliche Ordnernamen verwendet. Clientbetriebssystem Ordnername Windows 98 \\WIN98 Windows Me \\WINME Windows XP, 2000 \\WIN2000 Windows NT 4.0 \\WINNT40 3. Wählen Sie den Namen des Druckers aus, und klicken Sie auf OK. Folgen Sie dann den Anweisungen am Bildschirm. Hinweis: Wenn Sie EPSON Status Monitor 3 ebenfalls installieren möchten, finden Sie weitere Anweisungen unter „Installieren von EPSON Status Monitor 3“.
2. Zum Abbrechen aller Druckaufträge wählen Sie im Menü Drucker die Option Druckaufträge löschen (Windows Me oder 98) bzw. Alle Druckaufträge abbrechen (Windows XP, 2000 oder Windows NT 4.0). Zum Abbrechen eines bestimmten Dokumentdrucks wählen Sie den zugehörigen Druckauftrag aus, und wählen Sie dann im Menü Dokument die Option Druck abbrechen (Windows Me oder 98) bzw. Abbrechen (Windows XP, 2000 oder Windows NT 4.0). Der Druckauftrag wird abgebrochen.
3. Doppelklicken Sie auf das Symbol Software. 4. Wählen Sie EPSON-Druckersoftware, und klicken Sie auf Hinzufügen/Entfernen. 1 2 Hinweis: Klicken Sie unter Windows XP oder Windows 2000 auf Ändern oder Entfernen, wählen Sie EPSON-Druckersoftware, und klicken Sie dann auf Ändern/Entfernen.
5. Klicken Sie auf die Registerkarte Druckermodell, wählen Sie das Symbol des Druckers aus, den Sie deinstallieren möchten, und klicken Sie dann auf OK. 6. Klicken Sie zum Deinstallieren von Überwachte Drucker im angezeigten Dialogfeld auf Ja. Hinweis: Sie können lediglich das Utility Überwachte Drucker von EPSON Status Monitor 3 deinstallieren. Wenn das Utility deinstalliert wurde, können Sie die Einstellung für Überwachte Drucker in EPSON Status Monitor 3 nicht ändern. 7.
Deinstallieren des USB-Gerätetreibers Wenn der Drucker über ein USB-Schnittstellenkabel mit dem Computer verbunden ist, wird der USB-Gerätetreiber ebenfalls installiert. Beim Deinstallieren des Druckertreibers müssen Sie auch den USB-Gerätetreiber deinstallieren. Gehen Sie folgendermaßen vor, um den USB-Gerätetreiber zu deinstallieren. Hinweis: ❏ Deinstallieren Sie zuerst den Druckertreiber, bevor Sie den USB-Gerätetreiber deinstallieren.
Hinweis: ❏ EPSON USB-Gerätetreiber wird nur angezeigt, wenn der Drucker über ein USB-Schnittstellenkabel an einen Computer angeschlossen ist, auf dem Windows Me oder 98 ausgeführt wird. ❏ Wenn der USB-Gerätetreiber nicht ordnungsgemäß installiert wurde, wird EPSON USB-Gerätetreiber unter Umständen nicht angezeigt. Gehen Sie folgendermaßen vor, um die Datei Epusbun.exe auf der CD-ROM auszuführen. 1. Legen Sie die CD-ROM in das CD-ROM-Laufwerk des Computers ein. 2. Rufen Sie das CD-ROM-Laufwerk auf. 3.
Bedienfeld Verwenden des Bedienfelds Über die Tasten am Bedienfeld können Sie einfache Druckerfunktionen wie Zeilenvorschub, Seitenvorschub, Laden und Auswerfen von Papier und die Auswahl von Schriftarten steuern. Durch die Anzeigen am Bedienfeld wird der Druckerstatus angezeigt. Tasten und Anzeigen am Bedienfeld 1 6 7 2 3 4 5 1.
3. Taste „LF/FF“** ❏ Wenn diese Taste kurz gedrückt wird, wird das Papier zeilenweise transportiert. ❏ Bei gedrückt gehaltener Taste wird ein einzelnes Blatt ausgeworfen oder Endlospapier zur nächsten Druckstartposition transportiert. 4. Taste „Load/Eject“ (Laden/Ausgeben)** ❏ Ein einzelnes Blatt Papier wird geladen. ❏ Wenn Papier eingelegt ist, wird ein einzelnes Blatt ausgeworfen. ❏ Endlospapier wird aus der Bereitschaftsposition geladen. ❏ Transportiert Endlospapier zurück zur Bereitschaftsposition. 5.
* Schriftwahl: Im Mikroeinstellungsmodus können Sie die zum Drucken verwendete Schriftart auswählen, indem Sie die Taste „Tear Off (Font)“ (Abtrennen (Schriftart)) drücken. Die Anzeigen „Tear Off (Font)“ (Abtrennen (Schriftart)) leuchten, erlöschen oder blinken, um die gewählte Schriftart anzuzeigen. ** Mikroeinstellungsmodus: Wenn die Taste „Pause“ drei Sekunden lang gedrückt wird, schaltet der Drucker in den Mikroeinstellungsmodus.
Informationen zu den Standardeinstellungen des Druckers Mit den Standardeinstellungen werden viele der Druckerfunktionen gesteuert. Während Sie diese Funktionen oft über die Software oder den Druckertreiber einstellen können, müssen Sie dennoch gelegentlich eine Standardeinstellung über das Bedienfeld des Druckers ändern, indem Sie den Modus „Standardeinstellungen“ verwenden. In der folgenden Tabelle sind die Standardeinstellungen und die im Modus Standardeinstellungen verfügbaren Optionen aufgeführt.
Einstellungen Optionen Wortlänge 8 Bit, 7 Bit Paralleler I/F bidirektionaler Modus Ein, Aus Paketmodus Automatisch, Aus Zeichentabelle* Standardmodell: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15 Alle anderen Modelle: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 866, PC 869, MAZOWIA, Code MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774, Estonia, ISO 8859-2, PC 866 LAT, PC 866 UKR, PC APTEC, PC 708, P
Seitenlänge für Traktor Mit dieser Einstellung können Sie die Seitenlänge (in Zoll) für Endlospapier festlegen. Seitenperforation überspringen Diese Funktion ist nur verfügbar, wenn Endlospapier ausgewählt ist. Wenn Sie Ein auswählen, lässt der Drucker einen Rand von einem Zoll (25,4 mm) zwischen der letzten Zeile auf der einen Seite und der ersten Zeile der folgenden Seite frei.
Druckrichtung Sie können den Bidirektionaldruck (Bidirektional) oder Unidirektionaldruck (Unidirektional) auswählen. Der Druckvorgang ist normalerweise bidirektional, um das Drucken zu beschleunigen. Der unidirektionale Druck ermöglicht jedoch eine präzisere vertikale Ausrichtung, was beim Drucken von Grafiken sinnvoll ist. Betriebssystem Wenn Sie die Option ESC/P auswählen, arbeitet der Drucker im EPSON ESC/P-Modus.
Wartezeit für automatische I/F-Erkennung Diese Einstellung ist nur wirksam, wenn der „I/F-Modus (Schnittstellenmodus)“ auf Automatisch eingestellt ist. Diese Einstellung legt fest, wie lange der Drucker wartet, wenn keine Daten von einer Schnittstelle empfangen werden, bevor er überprüft, ob ein Druckauftrag über die andere Schnittstelle gesendet wird. Sie können die Wartezeit für die automatische Schnittstellenerkennung entweder auf 10 Sekunden oder auf 30 Sekunden festlegen.
Paketmodus Wählen Sie die Option Automatisch, wenn Sie aus Windows-Anwendungen mithilfe des Druckertreibers drucken möchten, der sich auf der mitgelieferten Software-CD-ROM des Druckers befindet. Deaktivieren Sie diesen Modus, wenn Sie Verbindungsprobleme beim Drucken aus Anwendungen unter anderen Betriebssystemen wie z. B. DOS haben. Zeichentabelle Sie können zwischen verschiedenen Zeichentabellen auswählen.
Autom. W-Rücklauf (Wagenrücklauf) Diese Einstellung ist nur im Emulationsmodus IBM 2380 Plus (für LX-300+II)/IBM 2381 Plus (für LX-1170II) verfügbar. Wenn der automatische Wagenrücklauf aktiviert ist, wird an jeden Zeilenvorschubbefehl (LF) bzw. ESC J-Befehl ein Wagenrücklaufbefehl angehängt. Die Druckposition wird dadurch an den Anfang der nächsten Zeile verschoben. IBM-Zeichentabelle Diese Einstellung ist nur im Emulationsmodus IBM 2380 Plus (für LX-300+II)/IBM 2381 Plus (für LX-1170II) verfügbar.
2. Schalten Sie den Drucker ein, während Sie die Taste Tear Off (Font) (Abtrennen (Schriftart)) gedrückt halten. Der Drucker wechselt in den Modus Standardeinstellungen und druckt die Anweisungen zur Sprachauswahl. 3. Folgen Sie den Anweisungen, um die gewünschte Sprache für die Anleitungsseiten auszuwählen. 4. Legen Sie gegebenenfalls das nächste Blatt ein. Der Drucker druckt die Liste der aktuellen Einstellungen (eine Seite). 5. Drücken Sie die Taste Tear Off (Font) (Abtrennen (Schriftart)).
Fehlerbehebung Verwenden der Fehleranzeigen Viele Druckerprobleme können Sie anhand der Bedienfeldanzeigen erkennen. Wenn der Drucker aufhört zu drucken und mindestens eine Bedienfeldanzeige leuchtet oder blinkt oder der Drucker akustische Signale ausgibt, können Sie das Problem anhand der folgenden Tabelle erkennen und lösen. Wenn Sie das Problem nicht anhand der Angaben in dieser Tabelle beheben können, finden Sie im nächsten Abschnitt weitere Informationen.
Status der Bedienfeldanzeige Akustische Signale Problem n Paper Out (Kein Papier) n Pause ••• In der ausgewählten Papierzufuhr ist kein Papier eingelegt. Lösung Legen Sie Papier in den Drucker ein. Drücken Sie gegebenenfalls die Taste Pause, sodass die Anzeige Pause erlischt. ••• Das Papier ist nicht richtig eingelegt. Entnehmen Sie das Papier, und legen Sie es erneut ein. Anweisungen zum Einlegen von Papier finden Sie unter „Drucken auf Endlospapier“.
Status der Bedienfeldanzeige Akustische Signale Problem f Sämtliche Bedienfeldanzeigen ••••• Ein unbekannter Druckerfehler ist aufgetreten. Lösung Schalten Sie den Drucker aus, lassen Sie ihn einige Minuten ausgeschaltet, und schalten Sie ihn dann wieder ein. Sollte der Fehler erneut auftreten, wenden Sie sich an Ihren Fachhändler.
Stromversorgung Die Stromversorgung ist unterbrochen. Die Bedienfeldanzeigen leuchten nicht. Ursache Aktion Möglicherweise ist das Netzkabel nicht an eine Stromquelle angeschlossen. Überprüfen Sie, ob das Netzkabel an eine Steckdose angeschlossen ist. Möglicherweise ist die Steckdose außer Betrieb. Verwenden Sie eine andere Steckdose, wenn die Steckdose mithilfe eines externen Schalters oder einer automatischen Zeitschaltuhr gesteuert wird. Schließen Sie einen anderen Verbraucher wie z. B.
Druckvorgang Der Drucker druckt nicht. Die Anzeige Pause leuchtet nicht. Trotzdem wird der Druckvorgang nicht gestartet. Ursache Aktion Möglicherweise ist die Software nicht ordnungsgemäß installiert. Überprüfen Sie, ob die Software ordnungsgemäß, wie in dem Blatt „Hier starten“ beschrieben, installiert wurde. Überprüfen Sie die Druckereinstellungen der Software. Das Schnittstellenkabel stimmt nicht mit der Druckeroder Computerspezifikation überein. Überprüfen Sie beide Enden des Schnittstellenkabels.
Der Drucker erzeugt Druckgeräusche, druckt jedoch nicht. Ursache Aktion Möglicherweise ist die Farbbandkassette nicht ordnungsgemäß installiert. Weitere Informationen finden Sie im Blatt „Hier starten“. Das Farbband ist möglicherweise abgenutzt. Tauschen Sie die Farbbandkassette aus. Der Drucker erzeugt merkwürdige Geräusche, gibt fünf akustische Signale aus, und der Druckvorgang wird plötzlich abgebrochen.
Der Drucker erzeugt fünf akustische Signale, und alle Anzeigen blinken. Ursache Aktion Ein Fehler ist aufgetreten. Schalten Sie den Drucker aus und anschließend wieder ein. Wenn sich das Problem dadurch nicht beheben lässt, überprüfen Sie das Gerät auf einen möglichen Papierstau oder ein verklemmtes Farbband. Wenn kein Papierstau oder verklemmtes Farbband vorliegt, wenden Sie sich an Ihren Fachhändler oder einen autorisierten Kundendiensttechniker.
Der Ausdruck ist schwach oder ungleichmäßig Die Zeichen werden im unteren Bereich nicht vollständig gedruckt. Ursache Aktion Möglicherweise ist die Farbbandkassette nicht ordnungsgemäß installiert. Weitere Informationen dazu finden Sie im Abschnitt „Austauschen der Farbbandkassette“. Der Ausdruck ist schwach. Ursache Aktion Das Farbband ist möglicherweise abgenutzt. Tauschen Sie die Farbbandkassette aus, wie unter „Austauschen der Farbbandkassette“ beschrieben.
Es werden nicht die gewünschten Zeichen gedruckt. Die Schrifttypen oder Zeichen, die Sie mit der Software an den Drucker gesendet haben, wurden nicht gedruckt. Ursache Aktion Möglicherweise ist die Überprüfen Sie, ob die Software für den Software nicht Drucker ordnungsgemäß konfiguriert ist. ordnungsgemäß konfiguriert. Die über das Bedienfeld ausgewählte Schriftart wird nicht gedruckt.
Die Seitenlänge stimmt nicht mit der Länge des Papiers überein. Ursache Aktion Überprüfen Sie die Einstellungen der Möglicherweise ist die Einstellung der Seitenlänge in Seitenlänge in der Anwendungssoftware, und passen Sie sie gegebenenfalls an. der Anwendungssoftware nicht korrekt. Die Druckereinstellungen der Seitenlängen für den Traktor stimmen möglicherweise nicht mit der Größe des verwendeten Endlospapiers überein.
Handhabung der Druckmedien Einzelblattpapier wird nicht ordnungsgemäß eingezogen Das Papier wird nicht transportiert. Ursache Aktion Möglicherweise befindet sich Endlospapier im Drucker. Entfernen Sie das Endlospapier. Stellen Sie den Papierwahlhebel in die Einzelblattposition. Legen Sie ein neues Blatt ein. Das Papier in der Papierführung Verschieben Sie das Papier (und die befindet sich zu weit links oder Papierführungsschienen) ein wenig nach links oder rechts.
Endlospapier wird nicht richtig transportiert Das Endlospapier wird vom Traktor nicht transportiert. Ursache Aktion Möglicherweise befindet sich der Papierwahlhebel nicht in der richtigen Position. Überprüfen Sie, ob sich der Papierwahlhebel in der Position für Endlospapier befindet. Ist dies nicht der Fall, schalten Sie den Drucker aus, stellen Sie den Hebel in die richtige Position, und schalten Sie den Drucker wieder ein. Das Papier hat sich möglicherweise vom Traktor gelöst.
Das Papier hat nicht das für Stellen Sie sicher, dass Papiergröße und den Drucker zulässige Format -stärke im zulässigen Bereich liegen. oder Gewicht. Die Spezifikationen für Endlospapier finden Sie unter „Papier“. Heben Sie für eine korrekte Wenn Sie Mehrfachformulare Druckposition die Papierführung an. mit seitlicher Crimplock-Heftung verwenden, sind die Kopien möglicherweise nicht dem Original entsprechend ausgerichtet. Das Papier wird nicht ordnungsgemäß ausgeworfen.
Optionen Bei Verwendung des Einzelblatteinzugs wird das Papier nicht richtig eingezogen Das Papier wird nicht eingezogen. Ursache Aktion Möglicherweise ist der Einzelblatteinzug nicht ordnungsgemäß am Drucker angebracht. Installieren Sie den Einzelblatteinzug, wie unter „Einzelblatteinzug“ beschrieben, neu. Möglicherweise befindet sich der Papierwahlhebel nicht in der richtigen Position. Überprüfen Sie, ob sich der Papierwahlhebel in der Position für Einzelblattpapier befindet.
Es werden mehrere Blätter gleichzeitig eingezogen. Ursache Aktion Möglicherweise wurden zu viele Seiten in den Einzugsschacht eingelegt. Entfernen Sie einige Seiten. Informationen über Papiersorten und -mengen, die in den Einzelblatteinzug eingelegt werden können, finden Sie unter „Papier“. Sie haben möglicherweise den Entnehmen Sie das Papier, und fächern Papierstapel vor dem Einlegen Sie es auf. nicht aufgefächert. Das Papier wird schief eingezogen.
Das Wechseln zwischen Einzelblatteinzug und Schubtraktor funktioniert nicht ordnungsgemäß Die gewünschte Papiersorte wird nicht eingezogen. Ursache Aktion Möglicherweise befindet sich der Papierwahlhebel nicht in der richtigen Position. Ziehen Sie den Papierwahlhebel vorwärts, um Endlospapier einzuziehen, oder drücken Sie ihn zurück, um Einzelblattpapier einzuziehen.
Der Drucker funktioniert nicht ordnungsgemäß, wenn das Farberweiterungspaket installiert ist (nur LX-300+II) Die Bedienfeldanzeigen leuchten nicht. Ursache Aktion Möglicherweise ist der Motor Befolgen Sie die Anweisungen unter „Farberweiterungspaket (nur des Farberweiterungspakets LX-300+II)“. nicht ordnungsgemäß installiert. Die gewünschte Farbe oder bestimmte Zeichen werden nicht gedruckt.
Korrigieren von USB-Problemen Wenn Sie beim Betrieb des Druckers über einen USB-Anschluss Probleme haben, lesen Sie die Informationen in diesem Abschnitt. Stellen Sie sicher, dass das Betriebssystem Windows XP, Me, 98 oder 2000 auf dem Computer installiert ist. Der Computer muss standardmäßig über Windows XP, Me, 98 oder 2000 verfügen.
Wenn die Treiber richtig installiert sind, erscheint die Option EPSON USB-Gerätetreiber im Menü Geräte-Manager. Wenn die Option EPSON USB-Gerätetreiber nicht im Menü Geräte-Manager erscheint, klicken Sie auf das Pluszeichen (+) neben Andere Geräte, um die installierten Geräte anzuzeigen. Wenn USB-Drucker unter Andere Geräte erscheint, ist der USB-Druckertreiber nicht richtig installiert. Wenn EPSON LX-300+II oder EPSON LX-1170II angezeigt wird, ist der Druckertreiber nicht richtig installiert.
4. Wählen Sie unter Andere Geräte die Option USB-Drucker, EPSON LX-300+II oder EPSON LX-1170II aus, und klicken Sie auf Entfernen. Klicken Sie anschließend auf OK. 5. Wenn das folgende Dialogfeld angezeigt wird, klicken Sie auf OK. Klicken Sie dann zum Schließen des Dialogfelds Systemeigenschaften erneut auf OK. 6. Schalten Sie den Drucker aus, und starten Sie Ihren Computer neu. Installieren Sie dann alle Treiber neu gemäß den Anweisungen auf dem Blatt Hier starten.
Der Drucker funktioniert mit dem USB-Kabel nicht richtig Wenn Ihr Drucker mit dem USB-Kabel nicht ordnungsgemäß funktioniert, versuchen Sie es mit den folgenden Lösungen: ❏ Stellen Sie sicher, dass es sich bei dem von Ihnen verwendeten Kabel um ein abgeschirmtes USB-Standardkabel handelt. ❏ Wenn Sie einen USB-Hub verwenden, schließen Sie den Drucker auf der obersten Ebene an, oder verbinden Sie ihn direkt mit dem USB-Anschluss des Computers.
❏ Wenn die Selbsttestseite nicht ordnungsgemäß ausgedruckt wird, liegt das Problem beim Drucker. Weitere mögliche Ursachen und Lösungen für das Problem finden Sie unter „Probleme und Lösungen“. Sie können den Selbsttest sowohl auf Einzelblattpapier als auch auf Endlospapier drucken. Anweisungen zum Einlegen von Papier finden Sie unter „Drucken auf Endlospapier“ oder unter „Drucken auf Einzelblattpapier“.
3. Legen Sie bei der Verwendung von Einzelblattpapier das Papier in den Drucker ein. Nach einigen Sekunden zieht der Drucker das Papier automatisch ein und beginnt mit dem Ausdruck des Selbsttests. Eine Reihe von Zeichen wird gedruckt. Hinweis: Um den Selbsttest vorübergehend anzuhalten, betätigen Sie die Taste Pause. Um den Selbsttest wieder aufzunehmen, betätigen Sie die Taste Pause erneut. 4. Um den Selbsttest endgültig zu beenden, betätigen Sie die Taste Pause. Der Druckvorgang wird angehalten.
So erreichen Sie den Kundendienst Wenn Ihr Epson-Produkt nicht ordnungsgemäß funktioniert und Sie das Problem nicht mithilfe der Informationen zur Fehlerbehebung in der Produktdokumentation lösen können, wenden Sie sich an den Kundendienst. Kontaktadressen für den EPSON-Kundendienst finden Sie im Gesamteuropäischen Garantieschein.
Zubehör und Verbrauchsmaterialien Installation und Verwendung von Zubehör Einzelblatteinzug Der optionale Schacht für den Einzelblatteinzug (C80637✽ für LX-300+II/C80639✽ für LX-1170II) fasst bis zu 50 Blatt Standardpapier (82 g/m² bzw. 22 Lbs). Gehen Sie folgendermaßen vor, um den Einzelblatteinzug zu installieren: 1. Stellen Sie sicher, dass der Drucker ausgeschaltet ist. Nehmen Sie die Papierführung ab, und öffnen Sie deren Abdeckung. 2.
4. Halten Sie den Einzelblatteinzug mit beiden Händen fest, und drücken Sie die Verschlusshebel nach unten. Führen Sie die Kerben des Papierführungsschachts über die Befestigungszapfen des Druckers. Wenn Sie die Verschlusshebel loslassen, rastet der Papierführungsschacht ein. * * Verschlusshebel 5. Verschieben Sie die linke Papierführung, und richten Sie sie an der dreieckigen Markierung aus. Verschieben Sie dann die rechte Papierführung annähernd auf Breite des Papiers.
6. Ziehen Sie die Papierwahlhebel ganz nach vorne, bis die Papierführungen zurück klappen, sodass Papier eingelegt werden kann. 7. Nehmen Sie einen Stapel Papier, und fächern Sie ihn auf. Richten Sie Blätter an den Seiten- und Unterkanten durch Aufstoßen auf einer ebenen Unterlage bündig aneinander aus. c Achtung: Verwenden Sie im Einzelblatteinzug keine Umschläge, Mehrfachformulare, Kohlepapier oder Etiketten. 8. Legen Sie bis zu 50 Blatt Papier entlang der linken Papierführung ein. 9.
12. Bringen Sie die Papierführung am Einzelblatteinzug an, wie im Folgenden dargestellt. b a a. Ansicht von oben b. Entriegelungsstift 13. Schieben Sie die linke Papierführungsschiene in die Mitte bis zur Markierung. Verschieben Sie dann die rechte Papierführung entsprechend der verwendeten Papiergröße. Hinweis: ❏ Drücken Sie auf beide Entriegelungsstifte, um die Papierführung aus dem Einzelblatteinzug herauszunehmen.
Hinweis: Wenn Sie mehrere Seiten Endlospapier drucken, falten Sie die erste gedruckte Seite an der Perforierung nach vorne, sobald sie unterhalb der Druckerabdeckung herauskommt. Dadurch werden die gedruckten Seiten ordnungsgemäß transportiert und Papierstaus verhindert. Zugtraktoreinheit Ein zusätzlicher Zugtraktor (C80030✽ für LX-300+II/C80034✽ für LX-1170II) steht optional zur Verfügung. Sie können den Transport von Endlospapier verbessern, indem Sie gleichzeitig zwei Traktoren verwenden.
3. Beim LX-300+II sollte der Zugtraktor mit beiden Händen gehalten werden. Halten Sie den Traktor über den Montageeinschub an der Oberseite des Druckers, bis er in die richtige Position einrastet, wie in der folgenden Abbildung dargestellt. Die Stifte sollten spürbar einrasten. Beim LX-1170II sollte der Zugtraktor mit beiden Händen gehalten werden. Drücken Sie den Traktor in den Montageeinschub an der Oberseite des Druckers, und kippen Sie ihn in die richtige Position, wie im Folgenden dargestellt.
5. Schalten Sie den Drucker ein. Halten Sie die Taste LF/FF (Zeilen-/Seitenvorschub) gedrückt, um eine Seite Papier in den Drucker einzuziehen. 6. Lösen Sie die Verriegelungshebel der Stachelradführung des Zugtraktors, und passen Sie die Stachelradeinheiten der Breite des Papiers an. Stellen Sie sicher, dass die Stachelradeinheiten der beiden Traktoren so ausgerichtet sind, dass das Papier nicht gebogen wird. 7. Öffnen Sie die Stachelradabdeckungen.
Rollenpapierhalter Der optionale Rollenpapierhalter (#8310) ermöglicht die Verwendung von 216 mm (8,5 Zoll) breitem Rollenpapier, das auch für Telexgeräte verwendet wird. Dieses Zubehör steht nicht in allen Ländern zur Verfügung. Gehen Sie bei der Installation und Verwendung des Rollenpapierhalters folgendermaßen vor: 1. Schalten Sie den Drucker aus, und entfernen Sie die Papierführung. 2. Positionieren Sie den Rollenpapierhalter wie im Folgenden dargestellt unterhalb des Druckers.
4. Schneiden Sie die vordere Papierkante gerade ab. Schieben Sie die Rollenpapierwelle durch die Mitte der Papierrolle. 5. Setzen Sie die Welle mit der Papierrolle auf den Rollenpapierhalter. Richten Sie die Rolle so aus, dass das Papier von unterhalb der Rolle eingezogen wird. Schalten Sie den Drucker ein. 6. Legen Sie die Vorderkante des Papiers über die Einzelblattpapierführung, und führen Sie es bis zum Anschlag in den Drucker ein. 7. Installieren Sie die Papierführung.
Farberweiterungspaket (nur LX-300+II) Das optionale Farberweiterungspaket (C83208✽) enthält eine Farbbandkassette und einen Motor. Gehen Sie folgendermaßen vor, um das Paket zu installieren: 1. Schalten Sie den Drucker aus, und nehmen Sie die Abdeckung des Druckers und die Papierspanneinheit ab. Verschieben Sie die Anschlussabdeckung auf dem Drucker, und ziehen Sie sie wie im Folgenden dargestellt heraus. 2. Installieren Sie den Motor in der rechten Ecke des Druckers mit dem Getriebe zur Mitte hin.
3. Schließen Sie den Motorstecker am Anschluss des Druckers an. 4. Schieben Sie den Druckkopf in die Mitte des Druckers, und schieben Sie dann den Plastikteil des Farbbands in die Mitte der Kassette. 5. Spannen Sie das Farbband, indem Sie den Spannknopf in Pfeilrichtung drehen.
6. Setzen Sie die Farbbandkassette wie abgebildet in den Drucker ein. Drücken Sie die Kassette dann fest an beiden Seiten herunter, bis die Plastikhalterungen in den Öffnungen am Drucker einrasten. 7. Schalten Sie den Drucker ein, während Sie die Tasten Load/Eject (Laden/Auswerfen) und Pause gleichzeitig gedrückt halten. Der Drucker druckt die Anweisungen zum Einstellen der Druckposition. 8. Führen Sie diese Anweisungen aus, um die Druckposition einzustellen.
9. Wenn Sie die Justierung der Druckposition beendet haben, schalten Sie den Drucker aus. Hinweis: Beim Drucken mit dem Farbband verringert sich die Druckgeschwindigkeit. Wenn Sie das schwarze Farbband verwenden möchten, entfernen Sie das farbige Farbband wie im Handbuch des optionalen Farberweiterungspakets beschrieben, und setzten Sie dann das schwarze Band wie unter „Austauschen der Farbbandkassette“ beschrieben ein. Der Motor muss dafür nicht herausgenommen werden.
Austauschen der Farbbandkassette Original-EPSON-Farbbandkassette Wenn der Ausdruck blass wird, müssen Sie die Farbbandkassette austauschen. Original-EPSON-Farbbandkassetten sind speziell auf die Verwendung mit dem EPSON-Drucker ausgelegt. Dadurch werden ein einwandfreier Betrieb und eine lange Nutzungsdauer des Druckkopfes und anderer Druckerteile gewährleistet. Andere nicht von EPSON hergestellte Produkte können Ihren Drucker beschädigen. Diese Schäden sind nicht von der EPSON-Garantie abgedeckt.
w Vorsicht: Unmittelbar nach dem Druckvorgang ist der Druckkopf noch heiß. Lassen Sie ihn einige Minuten abkühlen, bevor Sie die Farbbandkassette austauschen. 2. Klappen Sie die Druckerabdeckung zum Öffnen in die senkrechte Position, und ziehen Sie sie nach oben, um sie abzunehmen. 3. Entfernen Sie beim LX-1170II die Papierspanneinheit, indem Sie vorsichtig auf die Verriegelungsstifte drücken und die Papierspanneinheit aus dem Drucker nehmen. 4.
6. Zur leichteren Installation spannen Sie das Farbband, indem Sie den Spannknopf in Pfeilrichtung drehen. 7. Setzen Sie die Farbbandkassette wie abgebildet in den Drucker ein. Drücken Sie die Kassette dann fest an beiden Seiten herunter, bis die Plastikhalterungen in den Öffnungen am Drucker einrasten.
8. Verwenden Sie einen spitzen Gegenstand, wie z. B. einen Kugelschreiber, um das Band zwischen Druckkopf und Farbbandführung zu platzieren. 9. Drehen Sie den Spannknopf in Pfeilrichtung, um das Farbband in die richtige Position zu bringen. Das Band sollte nicht verdreht oder zerknittert sein. 10. Setzen Sie beim LX-1170II die Papierspanneinheit wieder ein. 11. Installieren und schließen Sie die Druckerabdeckung.
Produktinformationen Teile des Druckers b a c h d g e f a. Papierführungsschienen b. Papierstützen c. Papierführung d. Papierwahlhebel e. Papierzufuhrknopf f. Bedienfeld g. Druckerabdeckung h.
b c a d e j i h g f a. Serielle Schnittstelle b. Farbbandkassette c. Papierstärkehebel d. Papierspanneinheit e. Netzschalter f. Netzkabel g. USB-Kabelhalterung h. Traktor i. USB-Schnittstelle j.
Druckerspezifikationen Mechanik Druckverfahren: 9-Nadel-Matrixdruck Druckgeschwindigkeit: Schneller Entwurf 300 cps bei 10 cpi 337 cps bei 12 cpi 337 cps bei 15 cpi Schneller Entwurf 321 cps bei 17cpi (Schmaldruck) 300 cps bei 20 cpi Entwurf 225 cps bei 10 cpi 270 cps bei 12 cpi 225 cps bei 15 cpi Entwurf 191 cps bei 17 cpi (Schmaldruck) 225 cps bei 20 cpi Besserer 112 cps bei 10 cpi Entwurfsqualität NLQ 56 cps bei 10 cpi (Korrespondenz- 67 cps bei 12 cpi schrift) 56 cps bei 15 cpi 47 cps bei 17 cpi 56 cps
Einzugsmethode: Friktionsvorschub (Papierzuführung hinten) Schubtraktorvorschub (Papierzuführung hinten) Zug- und Schubtraktorvorschub (Papierzuführung hinten) Zugtraktorvorschub (Papierzuführung hinten oder unten) Einzug: Schubtraktor (hinten) Einzelblatteinzug (optional) Zugtraktoreinheit (optional) Rollenpapierhalter (optional) Einzugsgeschwindigkeit: Kontinuierlich 76 mm/Sekunde (3,0 Zoll/Sekunde) Zeilenweise 63 ms/Zeile bei einem Zeilenabstand von 1/6 Zoll Farbdruck (optional Methode Farbbandanhebung
Abmessungen und Gewicht (LX-300+II): Abmessungen und Gewicht (LX-1170II): Farbband: Lebensdauer des Farbbands (Entwurf, 10 cpi, 14 Punkte/Zeichen) Höhe Breite Tiefe Gewicht Höhe Breite Tiefe 159 mm (6,26 Zoll) 366 mm (14,4 Zoll) 275 mm (10,8 Zoll) (ohne Papierzufuhrknopf, Papierwahlhebel usw.) ca. 4,4 kg (9,7 Lbs) 164 mm (6,6 Zoll) 546 mm (21,5 Zoll) 275 mm (10,8 Zoll) (ohne Papierzufuhrknopf, Papierwahlhebel usw.) ca.
Elektronik Schnittstellen: Eine bidirektionale parallele 8-Bit-Standardschnittstelle mit Halb-Byte-Modus gemäß IEEE-1284, eine serielle EIA-232D-Schnittstelle und eine USB-Schnittstelle (Vers. 1.1).
Zeichentabellen: Eine Kursiv- und 12 Grafikzeichentabellen: Kursivtabelle, PC 437 (USA, Standard-Europa), PC 850 (Multilingual), PC 860 (Portugiesisch), PC 861 (Isländisch), PC 865 (Skandinavisch), PC 863 (Kanadisch-Französisch), BRASCII, Abicomp, ISO Latin 1, Roman 8, PC 858, ISO 8859-15 Die folgenden 26 Grafikzeichentabellen stehen in einigen Ländern zusätzlich zur Verfügung: PC 437 Griechisch, PC 852 (Osteuropa), PC 853 (Türkisch), PC 855 (Kyrillisch), PC 857 (Türkisch), PC 866 (Russisch), PC 869 (Griec
Elektrische Anschlusswerte Modell mit 120 V Eingangsspannungsbereich Modell mit 220-240 V 99-132 V Wechselstrom Nennfrequenzbereich 198-264 V Wechselstrom 50-60 Hz Eingangsfrequenzbereich 49,5-60,5 Hz Nennstrom 0,6 A (maximal 1,4 A je nach Zeichentyp) 0,3 A (maximal 0,7 A, je nach Zeichentyp) Stromverbrauch ca. 23 W (gemäß ISO/IEC 10561-Musterbrief) Hinweis: Überprüfen Sie das Typenschild auf der Rückseite des Druckers auf die angegebene Spannung.
Papier Hinweis: ❏ Verwenden Sie Recyclingpapier, Briefumschläge, Etiketten und Mehrfachformulare nur bei normalen Temperaturen und normaler Luftfeuchtigkeit unter folgenden Bedingungen: Temperatur: 15-25 °C (59-77 °F) Rel. Luftfeuchtigkeit: 30-60 % ❏ Legen Sie kein gefaltetes, beschädigtes, zerknittertes oder gewelltes Papier ein.
Mehrfachformulare aus Einzelblattpapier: Papierzuführung Breite 100-257 mm (3,9-10,1 Zoll) Länge 100-364 mm (3,9-14,3 Zoll) Kopien 1 Original + max. 4 Kopien Stärke 0,12-0,39 mm (0,0047-0.015 Zoll) Gewicht 40-58 g/m² (12-15 Lbs) Bindung Klebelinie an der oberen Kante oder an einer Seite des Formulars Briefumschläge: Papierzuführung Format Nr. 6: 165 × 92 mm (6,5 × 3,6 Zoll) Nr.
Etiketten: Zuführung unten Etikettenformat mindestens 23,8 × 63,5 mm (15/16 × 2,5 Zoll) Eckradius mindestens 2,5 mm (0,1 Zoll) Breite des Trägerblattes 101,6-254 mm (4,0-10,0 Zoll) Länge des Trägerblattes 101,6-558,8 mm (4,0-22,0 Zoll) Stärke des Trägerblattes 0,07-0,09 mm (0,0028-0,0035 Zoll) Gesamtstärke 0,16-0,19 mm (0,0063-0,0075 Zoll) Etikettengewicht 64 g/m² (17 Lbs) Rollenpapier: Hintere Zuführung mit optionalem Rollenpapierhalter Breite 216 mm (8,5 Zoll) Stärke 0,07-0,09 mm (0,0028-0,0035 Z
Stärke Papierführung: 0,065-0,14 mm (0,0025-0,0055 Zoll) Einzelblatteinzug: 0,07-0,14 mm (0,0028-0,0055 Zoll) Gewicht Papierführung: 52-90 g/m² (14-24 Lbs) Einzelblatteinzug: 64-90 g/m² (18-24 Lbs) Mehrfachformulare aus Einzelblattpapier: Papierzuführung Breite 148-420 mm (5,8-16,5 Zoll) Länge 100-364 mm (3,9-14,3 Zoll) Kopien 1 Original + max.
Endlospapier (Standard und mehrfach): Zuführung hinten und unten Breite 101,6-406,4 mm (4,0-16,0 Zoll) Länge (eine Seite) 101,6-558,8 mm (4.0-22,0 Zoll) Kopien 1 Original + max.
Druckbarer Bereich: Einzelblattpapier und Briefumschläge: LX-300+II A Der obere Mindestrand beträgt 4,2 mm (0,17 Zoll). B Der linke und rechte Mindestrand beträgt jeweils 3,0 mm (0,12 Zoll). Bei Einzelblättern beträgt die maximale Breite 257 mm (10,1 Zoll). Die maximale bedruckbare Breite beträgt 203,2 mm (8,0 Zoll). Wenn das Papierformat wesentlich breiter ist, werden die Seitenränder breiter. Die bedruckbare Breite ist jedoch maximal 203,2 mm (8,0 Zoll).
LX-1170II A Der obere Mindestrand beträgt 4,2 mm (0,17 Zoll). B Der linke und rechte Mindestrand beträgt jeweils 3,0 mm (0,12 Zoll). Bei Einzelblättern beträgt die maximale Breite 420 mm (16,5 Zoll). Die maximale bedruckbare Breite beträgt 345,44 mm (13,6 Zoll). Wenn das Papierformat wesentlich breiter ist, werden die Seitenränder breiter. Die bedruckbare Breite ist jedoch maximal 345,44 mm (13,6 Zoll). C 146 Der untere Mindestrand beträgt 4,2 mm (0,17 Zoll).
Endlospapier: LX-300+II A Der obere und untere Mindestrand bis zur Perforierung beträgt jeweils 4,2 mm (0,17 Zoll). B Der linke und rechte Mindestrand beträgt jeweils 13 mm (0,51 Zoll). Die maximale Papierbreite beträgt 254 mm (10,0 Zoll). Die maximale bedruckbare Breite beträgt 203,2 mm (8,0 Zoll). Wenn das Papierformat wesentlich breiter ist, werden die Seitenränder breiter. Die bedruckbare Breite ist jedoch maximal 203,2 mm (8,0 Zoll).
LX-1170II A Der obere und untere Mindestrand bis zur Perforierung beträgt jeweils 4,2 mm (0,17 Zoll). B Der linke und rechte Mindestrand beträgt jeweils 13 mm (0,51 Zoll). Die maximale Papierbreite beträgt 406,4 mm (16,0 Zoll). Die maximale bedruckbare Breite beträgt 345,44 mm (13,6 Zoll). Wenn das Papierformat wesentlich breiter ist, werden die Seitenränder breiter. Die bedruckbare Breite ist jedoch maximal 345,44 mm (13,6 Zoll). Rollenpapier: A Der obere Mindestrand beträgt 4,2 mm (0,17 Zoll).
Papierausrichtung Der Druck beginnt an der Markierung „0“. Der nicht bedruckbare Bereich liegt links von der Markierung „0“. Befehlslisten Der Drucker unterstützt folgende EPSON ESC/P-Steuerbefehle und die IBM 2380 Plus-Emulationssteuerbefehle (für LX-300+II) bzw. IBM 2381 Plus-Emulationssteuerbefehle (für LX-1170II). EPSON ESC/P-Steuercodes Durch die Auswahl eines EPSON ESC/P-Druckers in der Software können Sie erweiterte Schriften und Grafiken nutzen.
Seitenformat: ESC (C, ESC C, ESC C 0, ESC Q, ESC l, ESC (c, ESC N, ESC O, ESC (U Druckposition: ESC $, ESC \, ESC D, HT, ESC B, VT, ESC J Schriftauswahl: ESC k, ESC x, ESC y, ESC P, ESC M, ESC g, ESC p, ESC 4, ESC 5, ESC E, ESC F, ESC ! Schriftoptimierung: ESC W, DC4, SO, DC2, SI, ESC w, ESC G, ESC H, ESC T, ESC S, ESC Zeichenabstand: ESC Leerzeichen Zeichenverarbeitung: ESC t, ESC (t, ESC R, ESC %, ESC &, ESC :, ESC I, ESC 6, ESC 7 Bit-Image: ESC K, ESC L, ESC Y, ESC Z, ESC *, ESC ^ Barcode: ESC (B Farbdru
IBM 2380 Plus-Emulationssteuercode (für LX-300+II)/ IBM 2381 Plus-Emulationssteuercode (für LX-1170II) Der Drucker emuliert den IBM Proprinter mithilfe der im Folgenden aufgeführten Befehle. Ausführlichere Informationen finden Sie in den Referenzhandbüchern für IBM 2380 Plus (für LX-300+II)/IBM 2381 Plus (für LX-1170II).
Zeichenverarbeitung: ESC 6, ESC 7, ESC [T, ESC ^, ESC \ Bit-Image: ESC K, ESC L, ESC Y, ESC Z Barcode: ESC [f, ESC [p Herunterladen: ESC = (nur Entwurfsmodus) Normen und Richtlinien Sicherheitsrichtlinien (LX-300+II) 120 V-Version: Sicherheitsnormen UL60950 CSA60950 EMI FCC Part 15 Subpart B Klasse B CAN/CSA - CEI/IEC CISPR22 Klasse B 230 V-Version: 152 Sicherheitsnormen EN60950 EMI AS/NZS CISPR22 Klasse B
(Beide Modelle) 230 V-Version: Sicherheitsnormen EN60950 EMC EN55022 Klasse B EN61000-3-2 EN61000-3-3 EN55024 CE-Siegel (Beide Modelle) 230 V-Version: Niederspannungsdirektive 73/23/EEC EN60950 EMC-Direktive 89/336/EEC EN55022 Klasse B EN61000-3-2 EN61000-3-3 EN55024 153
Reinigen des Druckers Um einen optimalen Druckerbetrieb zu gewährleisten, sollten Sie das Gerät jährlich mehrmals wie folgt gründlich reinigen. Gehen Sie folgendermaßen vor, um den Drucker zu reinigen: 1. Entnehmen Sie sämtliches in den Drucker eingelegtes Papier. Stellen Sie sicher, dass der Drucker ausgeschaltet ist. 2. Entfernen Sie die Papierführung. Wenn ein Zugtraktor oder ein optionaler Einzelblatteinzug installiert ist, nehmen Sie diesen ab. 3.
c Achtung: ❏ Reinigen Sie den Drucker niemals mit Alkohol oder Verdünner. Diese Chemikalien können die Druckerbauteile und das Gehäuse beschädigen. ❏ Achten Sie darauf, dass kein Wasser oder andere Flüssigkeiten auf den Druckmechanismus und die elektronischen Bauelemente gelangen. ❏ Verwenden Sie keine harten oder scheuernden Bürsten. ❏ Sprühen Sie kein Schmiermittel in das Druckerinnere. Ungeeignete Schmierstoffe können den Druckermechanismus beschädigen.
1. Entnehmen Sie sämtliches in den Drucker eingelegtes Papier. Stellen Sie sicher, dass der Drucker ausgeschaltet ist. 2. Ziehen Sie den Netzstecker aus der Steckdose und anschließend das Schnittstellenkabel aus dem Drucker. 3. Senken Sie die Papierführung ab. Entfernen Sie die USB-Kabelhalterung, die Papierstütze und den Papierzufuhrknopf. 4. Wenn ein Zugtraktor installiert ist, entfernen Sie diesen.
Glossar Abtrennposition Die Position, zu der der Drucker das Papier im Abtrennmodus transportiert. Mithilfe der Mikroeinstellungsfunktion können Sie die Position so einstellen, dass die Perforierung des Papiers an der Abtrennkante ausgerichtet ist. ASCII Amerikanischer Standardcode für den Informationsaustausch (American Standard Code for Information Interchange). Ein standardisiertes Codesystem, mit dem Buchstaben und Symbolen numerische Codes zugeordnet werden können.
Druckstartposition Die Position auf dem Papier, die der Drucker als erste druckbare Zeile identifiziert. Dies ist die Standardposition für den oberen Rand. Eingangsspeicher Der Teil des Druckerspeichers, in dem Daten gespeichert werden, bevor sie gedruckt werden. Endlospapier Papier mit Transportlöchern an beiden Seiten und Perforierung zwischen den Seiten, das in einem Stapel aus gefaltetem Papier erhältlich ist. Diese Faltung wird auch als Leporellobruchfalzung oder Zickzackfaltung bezeichnet.
Papier in Leporellobruchfalzung/Zickzackfaltung Siehe „Endlospapier“. Punktmatrix Druckmethode, bei der jeder Buchstabe bzw. jedes Symbol durch ein Muster (Matrix) aus einzelnen Punkten gebildet wird. Schneller Entwurf Modus für Entwurfdruck, den Sie über den Modus „Standardeinstellungen“ auswählen können. Beim schnellen Entwurf wird ein Minimum an Punkten pro Zeichen verwendet, um extrem schnelles Drucken zu ermöglichen. Siehe auch „Entwurf“ und „Korrespondenzschrift (NLQ)“.
Unidirektionaler Druck Druckverfahren, bei dem der Druckkopf nur in eine Richtung druckt. Unidirektionaler Druck ist nützlich für das Drucken von Grafiken, da er eine präzise vertikale Ausrichtung ermöglicht. Sie können den unidirektionalen Druck im Modus „Standardeinstellungen“ des Druckers auswählen. Siehe auch „Bidirektionaldruck“. Walze Der schwarze, flache Teil, der das Papier während des Druckvorgangs stützt. Zeichen pro Zoll (cpi) Maßeinheit der Größe der Zeichen im Text.
Index A Abtrennautomatik, 85 Abtrennen, 28 automatisch, 29 einstellen, 29 Taste, 28 Anzeigen., 80 Ausrichten vertikaler Zeilen, 111 Autom. W-Rücklauf (Wagenrücklauf), 89 Autom.Z.-Vorschub, 85 B Baud rate, 87 Bedienfeld, 80, 91 Bedienfeld., 80 Betriebssystem Standardeinstellung, 86 Bidirektionaldruck., 86 Briefumschläge drucken, 37 Spezifikationen, 141, 143 C Clients unter Windows XP oder 2000, 67 Windows Me oder 98, 65 Windows NT 4.
Druckertreiber aufrufen unter Windows Me und 98, 40 unter Windows XP, 2000 oder Windows NT 4.0, 45 deinstallieren, 75 Einstellungen, 50 Druckrichtung, 86 E Einstellen Abtrennposition, 29 Druckstartposition, 25 Papierstärkehebel, 34 Einstellung für akustisches Signal, 88 Einzelblattpapier drucken, 31 Spezifikationen, 140, 142 Emulation.
IBM-Zeichentabelle Standardeinstellung, 89 Integrierte Schriftart Liste, 137 Internationale Zeichensätze, 138 International Zeichensatz für Italic, 88 K Kontaktaufnahme mit EPSON, 114 Kundendienst, 114 M Mehrfachformulare drucken, 35 Spezifikationen, 141, 143 Mikroeinstellung, 25, 29 N Null-Darstellung, 86 P Paketmodus, 88 Papierausrichtung, 149 Papierspezifikationen, 140 Papierstärkehebel, 34 Paralleler I/F bidirektionaler Modus, 87 Parität, 87 R Reinigen des Druckers, 154 Rollenpapier drucken, 122 Sp
Selbsttest, 111 Spezifikationen Befehlslisten ESC/P, 149 IBM 2380 Plus-/IBM 2381 Plus-Emulation, 151 Druckbereich, 145 elektrisch, 139 integrierte Schriftart, 137 internationale Zeichensätze, 138 Mechanik, 134 Normen und Richtlinien, 152 Papier, 140 Papierausrichtung, 149 Umgebungsbedingungen, 139 Zeichentabellen, 138 Standardeinstellungen ändern, 89 Liste der Optionen, 83 Status Monitor 3, 54 T Tasten., 80 Technischer Kundendienst, 114 Treiber (Druckertreiber), 38 U Unidirektionaldruck.