OKI People to People Technolog)' MICROLINE 3320/1 Read Me First0 Прочеши, преди да започнеш Strućna Pnrućka0 Bevezeto0 Przeczytaj To Najpierw Cite§te intii0 Щотреба Знати 9-PIN
Ml 3320/3321 Read Me First !
Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki assumes no responsibility for the results of errors beyond its control. Oki also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki.
Safety Your Oki printer has been carefully designed to give you years of safe, reliable performance. As with all electrical equipment, there are a few basic precautions you should take to avoid hurting yourself or damaging the printer: • Read the setup and operating instructions in this manual carefully. Be sure to save it for future reference. • Read and follow all warning and instruction labels on the printer itself. • Unplug the printer before you clean it.
Do not poke anything into the ventilation slots on the sides of the printer; you could get a shock or cause a fire. Aside from the routine maintenance described in this handbook, do not try to service the printer yourself; opening the cover may expose you to shocks or other hazards. Do not make any adjustments other than those outlined in the handbook, you might cause damage requiring extensive repair work.
•s; Contents Safety i Setting the Top of Form (TOF) Features 1 Temporarily Changing the Top of Form Setting 10 Optional Accessories 1 Resetting the Top of Form to the Standard Setting 10 Unpacking 1 Switching Paper Paths 11 Getting to Know Your Printer 2 Setting the Printhead Gap 11 Removing the Shipping Restraints 3 Running the Self Tests 12 Installing the Ribbon Cartridge 3 Font Sample Test 12 Connecting to the Power 5 ASCII Test 12 Loading Paper 5 Selecting an Emulation
Features • • • • • Unpacking Four printing speeds, from super-speed draft printing to near letter quality printing Rear tractor feed for continuous forms Top feed for single sheets Zero tear Three emulations: • Epson® FX • IBM'" Proprinter III • MICROLINE" Standard Optional Accessories • • • • • • • Top-Mount Pull Tractor for multipart forms, labels, etc.
Getting to Know Your Printer Carriage Cover Open Carriage Cover Paper Guides Access Cover Paper Separator Access Cover Paper Separator W Control Panel On-Off Switch On-Off Switch Paper Lever Platen Knob Set up for Raar Feed of Continuous Forms Control Panel Paper Lever Platen Knob Set up for Single-Sheet Feed 12 ML3320/21
Removing the Shipping Restraints installing the Ribbon Cartridge 1. Open the access cover and remove the printhead shipping retainer and the pull-up roller shipping retainer. 1. Make sure the printer is turned OFF. 2. Centre the printhead (®). 2. Remove the pull-up roller, then lift the paper separator and remove the shipping retainer. Replace the pull-up roller. 3. Unpack the ribbon cartridge.
4. Install the new ribbon cartridge. Connecting to the Computer Note: You must supply a shielded cable for connecting your printer to your computer. 1. When using the parallel interface cable, it needs to be fitted with an in-line filter. If your cable does not have an in-line filter, one has been supplied for you in your accessory pack. 5. Turn the knob (O) in the direction of the arrow to take up any ribbon slack.
Connecting to the Power Loading Paper 1. Make sure both the printer and the computer are OFF. Loading Continuous Forms (Rear Feed) 2. Plug the power cable into an earthed (3-pin) outlet. We recommend the rear-feed path for printing reports, etc., on single-thickness, continuous-form paper. For graphics or charts, it's best to use the single-sheet path (top feed). Note: The printer must be installed near to a power outlet switch which will remain easily accessible.
Move the paper lever to the position marked "REAR." 3. Pull up on the lock levers and open the tractor covers. sSI Grasp the paper separator, lift it slightly, pull back on it, then swing it forward.
5. Place the first two holes in the paper over the tractor pins on either side and close the tractor covers. 7. Adjust the right tractor to centre the paper holes on the pins, and push back the lock lever. 8. Lower the paper separator and place the wire guide (O) on the pull-up roller assembly (©). 6. Move the left tractor to align the edge of the paper with the appropriate reference mark (O), and push back the lock lever. 9. Press FF/LOAD. The paper feeds into the printer.
Loading Single Sheets (Top Feed) 3. Open the carriage cover and lift the paper separator to the single-sheet position. Use the single-sheet path for letterhead stationery, memos, and individual envelopes. It is recommended for printing graphs and charts because it provides the most accurate control of the paper. Note: Ifyou have continuous-form paper in the path, press the PARK button to remove it before loading single sheets. 1. Make sure the printer is on and deselected (SEL light off). - t 4.
5. Adjust the paper feed guides (©) for the width of the paper and place a sheet of paper in the separator. The paper will feed into the printer. Setting the Top of Form (TOF) • When setting the Top of horm, use the red line (O) on the paper shield as a reference: 1. Make sure the printer is deselected (SEL light off). 2.
3. Press SEL to re-select the printer. SEL Resetting the Top of Form to the Standard Setting 1. Turn the printer off. 2. Hold PARK + QUIET/TOF while turning the printer back on. Temporarily Changing the Top of Form Setting To set the Top of Form position lower for one page only: 1. Press SEL to deselect the printer. SEL 2. Press LF to change the position of the Top of Form. CROUP Note: 10 This setting will not apply to any following pages.
Switching Paper Paths Setting the Printhead Gap ;§ >—^ To switch from continuous-forms to single-sheet feed: 1. 2. 3. 4. 5. 6. Tear off any printed pages. Press PARK. Move the paper separator to the single-sheet feed position. Place the wire feed guide in the paper separator. Move the paper lever to the position marked "TOP." Place a sheet of paper in the paper separator. The printhead gap is the distance between the printhead and the platen.
Running the SelfTests Selecting an Emulation Font Sample Test Your printer has three emulations: • Epson® FX • IBM® Proprinter III • MICROLINE® Standard To run the test: Turn the printer off, then press and hold LF while turning the printer on. The printer comes set for the IBM Proprinter III emulation. To change to one of the other emulations: To stop the test: 1. Make sure paper is loaded. If you wish to stop the test before it is 2. Deselect the printer (SEL light off, press SEL key).
Selecting a Printer Driver 4. Press LF. (IROUP The following line will print: Printer Control Emulation Mode IBM PPR 5. Press TEAR consecutively until the emulation you wish to select prints in the right-hand column. П 6. Press SHIFT + SEL to save your setting and exit the Menu Mode. Read Me First Before you can use your printer with software, you must enter the software and select the correct printer driver.
Index L F Access cover Accessories ASCII test 2 1 12 Factory setting, top of form Font sample test Forms, head gap settings .... 10 12 11 G Carriage cover Computer connection Covers access carriage tractor 2 4 Guides, paper Guide, wire 2 2 5 H Head gap settings •• 11 IBM emulation Interface cable 13 ••••4 К Knob, platen Knob, ribbon take-up •—2 ....
w R Rear feed paper, loading Ribbon installation Rolling ASCII test 5-7 3-4 12 Wire guide 7,8 S Self tests Setting top of form Shield, paper Shipping restraints Single sheet paper, loading Take-up knob, ribbon Testing the printer Top of form Tractor cover Tractor pins U Unpacking 16 12 9 9 3 8-9 3, 4 12 9-10 5 5 1 ML3320/21
Oki Systems Company Oki Systems (UK) Limited 550 Dundee Road Slough Trading Estate Slough Berks.
113320/3321 Przeczytaj to najpierw
Podjęto wszelkie wysiłki, by w dokumencie przedstawić pewne i sprawdzone informacje wg stanu na dzień przygotowania niniejszego opracowania. OKI nie bierze na siebie odpowiedzialności za wynikłe błędy powstałe pozajej kontrolą. OKI nie może także zagwarantować, że zmiany w oprogramowaniu i wyposażeniu dokonane przez innych producentów i odpowiadające zawartym w tym podręczniku informacjom nie wpłyną na te informacje. Wymienienie nazw producentów oprogramowania nie oznacza ich popierania przez OKI.
Bezpieczeństwo użytkowania Twoja drukarka została bardzo starannie zaprojektowana, by zapewnić lata bezpiecznej i niezawodnej pracy. Drukarka jest urządzeniem elektrycznym; niewłaściwa obsługa drukarki może spowodować utratę zdrowia użytkownika lub jej zniszczenie. Poniżej przedstawiamy podstawowe zalecenia dotyczące bezpiecznego użytkowania drukarki: Dokładnie przeczytaj instrukcj e i opisy zawarte w podręczniku obsługi drukarki. Należy zachować podręcznik celem późniejszego wykorzystania.
Jeśli używamy przedłużacza lub rozgałęziacza połączonego z drukarką należy upewnić się, że całkowity pobór mocy podłączonych urządzeń jest niższy niż obciążenie nominalne przedłużacza lub rozgałęziacza. Całkowite obciążenie jednego gniazdka nie powinno być większe niż 15 Amperów.
Spis treści Bezpieczeństwo użytkowania I Ustawienie górnej krawędzi strony Właściwości 1 Chwilowa zmiana ustawienia górnej krawędzi strony Akcesoria dodatkowe 1 Przywrócenie ustawienia górnej krawędzi strony do Rozpakowanie drukarki 1 ustawienia fabrycznego 10 Poznawanie drukarki 2 Przełączanie ścieżek papieru 11 Usuwanie zabezpieczeń transportowych 3 Ustawianie szczeliny drukowania 11 Instalowanie kasety z taśmą 3 Przeprowadzanie autotestu 12 Podłączanie do komputera 4 Test czcio
Właściwości Rozpakowanie drukarki Cztery prędkości druku, od super szybkiego draftu do jakości korespondencyjnej Tylny podajnik dla składanki Górny podajnik pojedynczych arkuszy Brak oddzielania Trzy tryby emulacj i: • Epson® FX • IBM® Proprinter III • MICROLINE® Standard Akcesoria dodatkowe • Zamocowany na górze traktor ciągnący dla wielu formatów, etykiet, etc.
Poznawanie drukarki Otwarta pokrywa karetki Pokrywa karetki Ograniczniki papieru Separator papieru Pokrywa dostępu Pokrywa dostępu Separator papieru Panel sterowania Panel sterowania Włącznik zasilania Włącznik zasilania Dźwignia rodzaju papieru Pokrętło wałka Ustawienie dla składanki - podawanie papieru przez tylny traktor.
Usuwanie zabezpieczeń transportowych instalowanie kasety z taśmą 1. Otwórz pokrywę zamykającą i usuń zabezpieczenie transportowe głowicy drukującej i rolek dociskowych. 1. Upewnij się, że drukarka jest wyłączona (OFF). 2. Ustaw głowicę drukującą w pozycji środkowej (O). o 2. Wyjmij rolki dociskowe, następnie unieś separator papieru i usuń element zabezpieczający. Umieść na miejscu rolki dociskowe. 3. Rozpakuj kasetę z taśmą barwiacą.
Zainstaluj nową kasetę z taśmą barwiącą. Podłączanie do komputera Uwaga: Należy podłączyć do komputera kabelpołączeniowy drukarki. Wymagany jest kabel ekranowany. 1. Gdy używamy kabla interfejsu równoległego, musi być zaopatrzony w filtr przeciwzakłóceniowy. Jeśli zastosowany kabel nie zawiera wbudowanego filtru, należy użyć filtru dołączonego do zestawu drukarki - znajdującego się w opakowaniu z akcesoriami.
Podłączanie do zasilania Umieszczanie papieru 1. Upewnij się, że drukarka i komputer są wyłączone. Umieszczanie papieru ciągłego (traktor tylny) 2. Podłącz kabel zasilający do uziemionego gniazdka sieciowego. Uwaga:Drukarka musi być zainstalowana niedaleko gniazdka sieciowego tak, by zapewnić łatwy dostęp. Zalecamy podajnik tylny do druku raportów, etc., na pojedynczej grubości papierze typu składanka.
Przesuń dźwignię papieru do pozycji oznaczonej "REAR." Podnieś dźwignie blokujące i otwórz pokrywę traktora. . Uchwyć separator papieru, podnieś go delikatnie, odciągnij, następnie przesuń do przodu.
5. Umieść dwa pierwsze otwoiy perforacj i papieru na bolcach 7. Ustaw prawy traktor tak, by w otworach perforacj i papieru traktora po dwóch stronach i zamknij pokrywę traktora. umieszczone były centralnie bolce traktora, zamknij pokrywę traktora. W 4 — 1 \ г - Л 8. Zamknij separator papieru i umieść druciany protektor (©) na zespole rolek dociskowych (©). 6. Przesuń lewy traktor, by wyrównać brzeg papieru do odpowiedniego znaku (O), i przesuń do położenia początkowego dźwignię blokującą. 9.
Umieszczanie pojedynczych arkuszy (podajnik górny) Otwórz pokrywę karetki i podnieś separator papieru do pozycji pojedynczych arkuszy. Użyj ścieżki pobierania pojedynczych arkuszy papieru dla nagłówków papierów firmowych, pism i pojedynczych kopert. Ścieżka ta zalecana jest do druku grafiki i wykresów pozwalając na najlepsze sterowanie drukiem. Uwaga: Jeżeli w drukarce założonyjest papier ciągły, należy nacisnąć klawisz PARK, by usunąć papier przed załadowaniem pojedynczych arkuszy. 1.
Ustaw ograniczniki szerokości papieru (O) na szerokość papieru i umieść arkusz w separatorze. Papier zostanie wciągnięty do drukarki. o Ustawienie górnej krawędzi strony (TOF) Podczas ustawienia górnej krawędzi formularzajako odniesienia użyj czerwonej linii (O) umieszczonej na osłonie papieru jak 1. Upewnij się, że drukarka nie została wybrana (wskaźnik SEL wyłączony). 2.
3. Naciśnij SEL, by wybrać ponownie drukarkę. P r z y w r ó c e n i e ustawienia górnej krawędzi strony do ustawienia fabrycznego SE' 1. Wyłączyć drukarkę. C h w i l o w a zmiania ustawienia górnej krawędzi strony 2. Podczas włączania drukarki, nacisnąć PARK + QUIET/ TOF. W celu obniżenia górnej krawędzi wyłącznie dla jednej strony należy: 1. Nacisnąć SEL, by odłączyć drukarkę. 2. Nacisnąć LF, by zmienić ustawienie górnej krawędzi formularza. Uwaga: To ustawienie nie dotyczy kolejnych stron.
Przełączanie ścieżek papieru Ustawianie szczeliny drukowania W celu przełączenia rodzaju papieru ze składanki na pojedyncze arkusze: Szczelina drukowania jest to odległość pomiędzy głowicą drukującąi płaszczyznąpapieru. W celu ustawienia szczeliny, otwórz pokrywę drukarki i przesuń niebieską dźwignię (O) do zalecanego ustawienia zgodnie z ustawieniem przedstawionym w poniższej tabeli. 1. Odedrzyj wszystkie zadrukowane strony. 2. Naciśnij PARK. 3.
Przeprowadzanie autotestu Wybór emulacji Test czcionek wzorcowych Drukarka posiada trzy tryby emulacji: Uruchomienie testu:Wyłącz drukarkę, a następnie naciśnij i przytrzymaj LF podczas włączania drukarki. • Epson® FX IBM Proprinter III Microline Drukarka dostarczana jest z ustawionym trybem emulacji Epson FX. W celu zmiany trybu należy: Zatrzymanie testu: Zakończenie testu przed jego zakończeniem - naciśnij SEL. TestASCII 1. Upewnić się, że papier jest załadowany. 2.
Wybór sterownika drukarki 4. Naciśnij LF (GROUP). Przed rozpoczęciem użytkowania drukarki z oprogramowaniem, należy wejść do oprogramowania i wybrać właściwy sterownik drukarki. Jeśli zostanie wybrany zły sterownik, to na wydruku pojawią się dziwne znaki, niewłaściwe czcionki etc. Zostanie wydrukowana następująca linia: Printer Control Emulation Mode EPSON FX 5. Naciskaj kilkakrotnie TEAR (SET) do czasu pojawienia się w ostatniej kolumnie żądanego trybu emulacji.
Indeks A Akcesoria Autotest 1 12 Bolce traktora 5 С Czcionki - test 1 D Dźwignia blokująca 5 Dźwignia papieru 2 E Emulacja 1, 12-13 Emulacja Epson 1, 12-13 Emulacja IBM 1, 12-13 Emulacja Proprinter 1, 12-13 Etykiety, ustawienie przew. druku 11 Formularze, ustawienie przew. druku ..11 Przeczytaj to najpierw G Gałka, pociągowa taśmy. Gałka, wałek Górna krawędź strony .... К Kabel Interfejsu Kabel, równoległy Koperty P 3 4 2 9_10 4 .
ś Ścieżka papieru, zmiana 11 T Taśma - osłona Taśma - zakładanie Test ASCII Test czcionek wzorcowych Testowanie drukarki Transport drukarki Tryby druku Tylny podajnik papieru, ładowanie 3 3-4 12 12 12 3 1 5-7 U Ustawianie góry strony Ustawienia fabryczne, góra strony 9-10 10 W Włącznik zasilania 2, 5 Z Zakładanie gałki, taśmy PL-16 3, 4 ML3320/21