Epson PowerLite 7900p Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 10 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 11 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 11 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Additional Components. . . .
2 3 4 Contents Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 36 Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 36 Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 38 What To Do If You See a Blank Screen . . . . . . . . . . . . . 39 The Projector and Notebook Don’t Display the Same Image . . . . . . . . . . . . . . . . 39 Adjusting the Image . . .
4 5 Fine-tuning the Projector . . . . . . . . . . . . . . . . . . . . 65 Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 67 Adjusting the Image Quality. . . . . . . . . . . . . . . . . . . . . . . . . 68 Adjusting Images from Video Sources . . . . . . . . . . . . . . 68 Adjusting Computer Images. . . . . . . . . . . . . . . . . . . . . . 69 Adjusting the Image Size, Shape, and Position . . . . . . . . .
Using EMP NetworkManager . . . . . . . . . . . . . . . . . . . . . . . 96 Selecting the Projectors to Monitor . . . . . . . . . . . . . . . . 96 Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Creating the E-Mail Settings . . . . . . . . . . . . . . . . . . . . . 97 Understanding the Notification Messages . . . . . . . . . . . 99 6 7 A B 6 Contents Maintaining the Projector. . . . . . . . . . . . . . . . . . 101 Cleaning the Lens. . . . . . . . . . . . . . . . . . . . .
C Appendix C: Notices . . . . . . . . . . . . . . . . . . . . . . . . 131 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 131 Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 133 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 134 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 135 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Index . . . . . . . . . . . . . .
Contents
- Welcome The Epson ® PowerLite® 7900p is a versatile, lightweight projector designed to ensure that your presentations are easy and trouble-free, whether you use it in the classroom or conference room. When space is limited, you can project against a surface less than five and one-half feet away.
To prevent unauthorized use of your PowerLite 7900p, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projector’s buttons through the Operation Lock feature. For more information about security features, see page 77.
Using Your Documentation Your documentation includes a Quick Setup sheet, warranty brochures, and Epson PrivateLine® Support card. The Quick Setup sheet gives instructions for setting up your projector and connecting it to a notebook or PowerBook® computer. This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury.
Registration and Warranty Your projector comes with a basic carry-in warranty as well as an international warranty that let you project with confidence anywhere in the world. For details, see page 136 and the warranty brochure included with your projector. In addition, for customers who register their projector, Epson offers free Extra CareSM Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: Projector Remote control and batteries Power cable Projector software CD-ROM VGA computer cable Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
Additional Components Depending on how you plan to use the projector, you may need additional components: 14 Welcome ■ To receive an S-Video signal, you’ll need an S-Video cable. One may be provided with your video equipment, or you can purchase one from Epson; see page 15. ■ To receive a component video signal from a VCR or other video device, you’ll need a component video cable. One may be provided with your video equipment, or you can purchase one from Epson; see page 15.
Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Part number Replacement lamp V13H010L22 Air filter replacement set V13H134A01 Middle throw zoom lens (standard lens) Wide throw zoom lens Long throw zoom lens V12H004M03 V12H004W03 V12H004L05 ATA shipping case ATA molded hardshell case ELPKS46 ELPKS48 Ceiling mount Suspension adapter False ceiling plate Adjustable ceiling channel Security bracket/cabling ELPMB40 ELPMBAPL ELPMBFCP
Welcome
1 Setting Up the Projector T his chapter gives you basic information on setting up the projector: where to position it and how to connect it to a video source (such as a VCR or DVD player) or to a notebook or desktop computer.
note Positioning the Projector You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 123 for details. If you’re setting up the projector yourself and it isn’t already installed in the theater or conference room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. x art below This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. Screen Projector note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector’s left side. You can purchase this from Epson; see “Optional Accessories” on page 15.
Connecting to Video Equipment You can connect up to four video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video-output connections: RCA connector (composite video) S-Video connector (4-pin mini-DIN) BNC connector (component video) ■ If your video player has a yellow RCA-style video output connector, see “Connecting a Composite Video Source” on page 21.
Connecting a Composite Video Source 1. Locate an RCA-style video cable (one may be included with your video equipment). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: 3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4.
Connecting an S-Video Source 1. Locate an S-Video cable (one is usually provided with your video equipment, or you can purchase one from Epson; see page 15). 2. Connect the cable between the S-Video connector on your player and the S-Video connector on the projector: 3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4.
Connecting a Component Video Source 1. Locate a component video cable (one may be included with your video equipment). BNC adapters Look at the connectors at one end of the cable. If they are bayonet-style (BNC) connectors, continue on to the next step. If they are RCA-style connectors, you’ll need to attach commercially available BNC adapters to plug the cable into your projector. 2. Connect the cable (with the adapters) to your player and the BNC connectors on the projector.
Connecting an RGB Video Source Follow these instructions to connect the projector to a video player that has an RGB video output port. Depending on the type of connector on your player, you’ll need to use the appropriate cable: ■ If your player has a VGA-style connector, see below. ■ If your player has three connectors labeled R/G/B, see “Connecting Using a BNC-style Cable” on page 25. Connecting Using a VGA-style Computer Cable 1. Locate the VGA computer cable provided with the projector. 2.
Connecting Using a BNC-style Cable 1. Locate a BNC-style video cable (one may be included with your video equipment). 2. Connect the cable between your player and the corresponding R/G/B connectors on the projector. 3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4. If you don’t need to make any other connections, see Chapter 2 or the Quick Setup sheet for instructions on turning on the projector and adjusting the image. 5.
Connecting to a Computer note If you connect a Windowsbased computer to the projector, you may see a New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click Cancel. note If you want to connect an external monitor to the Monitor Out port, your computer must be connected to either the Computer or BNC ports. The Monitor Out port does not support a DVI connection.
Connecting to the Computer Port Follow these instructions: 1. )Locate the VGA computer cable provided with the projector. 2. Connect one end to the projector’s Computer port, and the other end to your computer’s monitor port. caution Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector. note 3.
Connecting to the BNC Connectors 1. Obtain a commercially available standard BNC to VGA component video cable. BNC to VGA component video cable 2. Plug the BNC connectors into the projector’s B/Cb/Pb, G/Y, and R/Cr/Pr connectors as shown below. Depending on your computer’s video card, you may have to connect to the projector’s V Sync and H/C Sync connectors too. (See your computer documentation for more information.) B/Cb/Pb R/Cr/Pr G/Y 3.
Connecting to the DVI Port 1. Obtain a commercially available DVI digital video cable (either DVI to DVI or DVI to DFP; see page 15 for details about ordering a cable from Epson). 2. Connect the cable to the projector’s DVI port as shown. note Various types of DVI cables are offered on the market. Be sure to use only a cable with DVI to DVI or DVI to DFP connectors. 3. Connect the other end to your computer’s DVI port. 4.
Using the Macintosh Desktop Adapter If you have an older desktop Macintosh or PowerBook, the VGA cable may not fit when you try to connect it. If so, you’ll need to use the Macintosh desktop adapter to connect the VGA cable to your computer. This is available from Epson (see page 15). 1. To use the adapter, remove its cover as shown and set its DIP switches according to the resolution you want to use, such as 16-inch mode. See the instructions included with the adapter. 2.
Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter, you can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 30 feet away. The wireless mouse function is supported on systems with a USB port running Windows XP, 98SE, 2000, or Me, or Macintosh OS 8.6 to OS X 10.2 or later. 1. Obtain a commercially available standard USB cable. 2.
Connecting an External Monitor note If you want to connect an external monitor to the Monitor Out port, your computer must be connected to either the Computer or BNC ports. The Monitor Out port does not support a DVI connection. If you want to monitor your presentation close-up (on a monitor placed beside the projector) as well as on the screen, you can connect an external monitor.
Playing Sound Through the Projector You can play sound through the projector’s speaker system, or you can attach an external speaker system. (Attaching speakers to the projector instead of directly to the audio source lets you use the projector’s remote control to adjust the sound.) Connecting Audio Equipment to the Projector To play sound through the projector, follow these steps: 1. Obtain a commercially available stereo mini-jack or RCA-style audio cable.
Connecting External Speakers To connect speakers to the projector, follow these steps: 1. Obtain the appropriate cable to connect your speakers. Depending on your stereo system, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end, and pin jacks on the other end. For some speaker systems, you may have to purchase a special cable or use an adapter to connect to your speakers. 2.
1 Projecting Once you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
Turning On Your Equipment Make sure your projector and other equipment are set up as described in Chapter 1. Then follow the instructions below to start the projector and display an image. note To shut down the projector, see page 49. Shutting down the projector correctly prevents premature lamp failure and possible damage from overheating. If you turn on any connected computer or video equipment before starting the projector, this lets the projector automatically detect and display the image source.
4. Press the red P Power button on top of the projector—or press the P Power button on the remote control. (If this is your first time using the remote control, make sure the batteries are installed and the on/off switch on the side of the remote is turned on; see page 52.) Turn on remote Power button note If the Direct Power ON feature has been enabled, you don’t need to press the P Power button to turn the projector on. Just plug the projector into an electrical outlet.
Selecting the Image Source note To focus and adjust the image, see page 42. If a projected image fails to appear, see page 39 for help. Selecting the image source lets you switch between images input from different pieces of equipment connected to the projector (such as a computer or DVD player). If you don’t see the image you want, select it using the Source buttons either on the projector or the remote control.
What To Do If You See a Blank Screen If you see a blank screen or a blue screen with the No Signal message, try the following: ■ Make sure the cables are connected correctly, as described in Chapter 1. ■ Make sure the P Power light is green and not flashing and the lens cap is off. ■ If you’ve connected more than one computer and/or video source, you may need to press one of the Source buttons on the projector’s control panel or the remote control to select the correct source.
From the Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details. If you’re using Macintosh OS X: You may need to set up your system to display on the projector screen as well as the LCD screen.
If you’re using OS 8.6 to OS 9.x: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound. 2. Click the Arrange icon. Click here Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other. If the Arrange option isn’t available, you may need to select one of the Simulscan resolution settings: 1. Click the Monitor icon.
Adjusting the Image Once you see your image, you need to make certain adjustments: ■ To focus or zoom your image, see below. ■ If the image is too high or too low, you can reposition it. See page 43. ■ If the image isn’t square, see page 44. ■ If a computer image displays incorrectly, see page 47. If you need to fine-tune the image and/or sound, see Chapter 4. Focusing and Zooming Your Image Use the Focus ring on the projector to sharpen the image.
Adjusting the Height of Your Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1. Stand behind the projector. Press the blue foot release lever up and lift the front of the projector. 2. Once the image is positioned where you want it, release the lever to lock the foot in position. 3. If necessary, you can fine-tune the height by turning the projector’s rear feet.
Adjusting the Image Shape In most cases, you can maintain a square or rectangular image by placing the projector directly in front of the center of the screen with the base of the lens level with the bottom of the screen. Even if the projector is slightly tilted (within a range of 40° up or down), the projector has an automatic keystone correction function that detects and corrects vertical keystone distortion.
Using Keystone Correction To adjust your image when it is wider on one side, do the following: ■ Look at the shapes of the icons on the projector’s four Keystone buttons. Press the button whose icon is the mirror image of the shape of your screen image. Continue pressing the button until you are satisfied with the shape of the image. Keystone buttons ■ note The image will be slightly shorter after adjusting.
You see this screen: [ / ]:Adjust Adjust [ ] :Move next [ESC] :Return (Press 1 second to reset) note If you are not satisfied with the corrections made, press the ESC button for one second to reset the screen to its original shape. 5. Press the Enter button to select the corner you want to adjust. 6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape. 7. Repeat steps 5 and 6 as needed to adjust any remaining corners. 8.
Correcting Computer Images If you’re connected to a computer and the image doesn’t look right, press the Auto button on the remote control (or the Auto/Enter button on the projector’s control panel). This automatically resets the projector’s tracking, sync, resolution, and position settings.
Projecting Images Without a Screen Even if you don’t have a screen, you can project images onto surfaces like blackboards and colored walls without loss of image color. Your projector has a sensor that measures the conditions of the projection surface and automatically adjusts the colors and shading of your image. For example, if you’re projecting onto a surface near a window, your image appears clear and well-defined rather than faint.
Adjusting Color Corrections for a New Surface Adjust the correction values if you’re projecting on a new surface or in a new location. 1. Press the Wall Shot button on the remote control or projector while you’re projecting an image. Wait for the Wall Shot status screen. 2. Press the Wall Shot button until you see Wall Shot Readjustment on the status screen. You see a sequence of colors flash for about five seconds as the projector adjusts the color correction values for the new projection surface.
caution To avoid damaging the projector or lamp, never unplug the power cord when the P Power light is green or flashing orange. 3. Press the P Power button again. The power light flashes orange for about 30 seconds as the projector cools down. After the projector has cooled, the orange light stays on and the exhaust fan shuts off. If you want to turn the projector on again, wait until the orange light stops flashing. Then press the P Power button. 4.
1 Using the Remote Control T he remote control lets you access your projector’s features from anywhere in the room—up to 33 feet away. For example, you can turn the projector on and off, preview and switch between picture sources, turn off picture and sound, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings; see Chapter 4).
Activating and Using the Remote Control The remote control has an ON/OFF switch on its side, as shown. Before using the remote, make sure batteries are installed as described on page 54, then push up on the ON/OFF switch to turn it on. On/off switch note If a button is pressed longer than 60 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes.
Using the Navigation Buttons The remote control has various buttons that let you navigate the projector’s help and menu systems; they also let you use the drawing tools to highlight your presentation. If you’ve connected a computer, the buttons can be used in place of your computer’s mouse, letting you walk about freely while controlling your presentation.
Replacing the Batteries If the projector stops responding to the remote control, check the following: ■ Make sure the remote control’s ON/OFF switch (shown on page 52) is in the ON position. ■ Press the light button and check to see if the buttons on the remote control light up. (If you’re in a bright room, you may not be able to see them light.) caution If the buttons do not light up, replace the batteries as described below: When replacing batteries, take the following precautions: 1.
Controlling the Picture and Sound You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, display a picture-in-picture image, and adjust the volume. note You can use the projector’s menus to fine-tune the picture and sound quality as described in Chapter 4.
Previewing Picture Sources You can use the Preview function to help you select the image source. 1. Press Preview on the remote control. Preview button You see the currently selected source displayed in the main window, as shown. All other sources (including the currently selected source) are displayed in smaller preview windows on the right side and at the bottom. If no equipment is connected to a port, or if there is no incoming signal, the preview window for that source appears blank.
Turning Off the Picture and Sound You can use the A/V Mute button on the remote control to turn off the image and sound and darken your screen. (If you’ve connected an external monitor to the projector, it will continue displaying.) This feature is useful if you want to temporarily redirect your audience’s attention without the distraction of a bright screen. ■ To turn off the picture, press the A/V Mute button. The screen goes dark. ■ To turn the image back on, press the button again.
3. Continue pressing the E-Zoom area up to 4× . button to enlarge the selected 4. While the image is enlarged, you can: ■ Use the pointer button to pan about. ■ Press the E-Zoom button to zoom out. 5. When done, press the ESC button to return to the original size. Displaying a Picture-in-Picture Video note The Picture-in-Picture function does not work for RGB video images.
3. Once the window is located and sized the way you want it, press the Enter button; your video continues playing on the screen. Video window 4. When you’re finished viewing the Picture-in-Picture, press the P in P or pointer button again. The window disappears. Highlighting Your Presentation You can display a pointer to call out something on the screen, or draw straight or curved lines to emphasize particular points.
2. Use the pointer button on the remote control to position the pointer on the screen. 3. To draw a straight line, place the pointer where you want the line to begin and press Enter. Move the pointer to where you want the line to end, and press Enter again. 4. To draw a curved line, place the pointer at the start of the line, then press and hold the Enter button until it lights. Then use the pointer button to move the pointer and draw on the screen. Press ESC when done. 5.
2. For each of the three Pointer/Line icons, you can change the following settings: ■ Shape Lets you select one of the following pointer shapes: ■ Zoom Rate Changes the size of the pointer ■ Color Changes the color of the line you can draw using the pointer ■ Width Changes the line width 3. You can also change the Pointer Speed setting to adjust how fast the pointer tool moves across the screen. 4. When done, press ESC until you exit from the menu system.
Operating Your Computer with the Remote Control If you’ve connected a computer to the projector with a USB cable, as described on page 31, you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering PowerPoint and other slideshow-style presentations, since you won’t have to stand next to the computer to change slides. Use to move cursor Left-click ■ Use the pointer button to move the cursor on the screen.
Controlling Multiple Projectors If you’re using more than one projector, you can control all the projectors—or just selected ones—by using the projector ID system. To operate a projector, you have to set the remote control’s ID to match that of the projector. Or you can control all of the projectors simultaneously by setting the remote control’s ID to zero. Setting the Projector ID The projector’s default ID is 1. If you need to change it, follow these steps: 1. Press the Menu button on the remote control.
Setting the Remote Control ID The remote control’s default ID is zero. If you need to change it, follow these steps: 1. Press the ID button on the remote control. You see it light. 2. Press one of the numbered buttons on the remote control to select the desired ID (0 through 9). Select zero to control all projectors, or select a number to match the ID of the projector(s) you want to operate. Nine Zero The ID button’s light shuts off and the new ID is registered.
1 Fine-tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control (or the projector’s control panel) to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button. You see a menu screen similar to the one shown below (the settings may differ from those shown here, depending on the selected input source): Options Position Adjust : 0000 Tracking Sync.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to see a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting, then press Enter. + - ON OFF 5.
Adjusting the Image Quality You can use the Video menu to adjust the brightness, sharpness, color, tint, and contrast. If you’re projecting from a computer (but not through the DVI port), there are additional adjustments you can make (see page 69). Adjusting Images from Video Sources 1. Press the Menu button on the remote control, then select the Video menu. You see the Video menu screen. (The actual settings may vary, depending on the selected input source.
■ Color Adjusts the color intensity, from black-and-white to full color (not available for RGB video images). ■ Tint Adjusts the tint of the image (not available for RGB video images). ■ Sharpness Adjusts the sharpness of the image. Adjusting Computer Images You can also adjust brightness, contrast, and sharpness when you’re projecting a computer image. In addition, if you’re projecting an analog RGB image transmitted through the Computer or BNC port(s), you can make several other settings.
■ Sync Adjust this value if the image appears blurry or flickers. ■ Brightness Lightens or darkens the overall image. ■ Contrast Adjusts the difference between light and dark areas. Select Auto to let the projector adjust the contrast automatically, or select Manual to adjust the setting yourself. (Press Enter after you make the selection.) ■ Sharpness Adjusts the sharpness of the image.
Adjusting the Image Size, Shape, and Position Whether you’re projecting from a computer or video player, you can use these settings to adjust the size, shape, and position of the image. ■ Resize button Adjusts how an image fits into the display area. For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area.
Adjusting the Color The projector provides several ways for you to adjust the color: ■ Color Mode button (also in the Video menu) Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the Color Mode setting in the Video menu; you can save a different setting for each computer and/or video source.
Adjusting the Sound You can use the Audio menu to adjust the sound volume or treble/bass balance. 1. Press the Menu button on the remote control, then enter the Audio menu. note You can also adjust the volume using the remote control. You see the Audio menu screen: Video Audio Effect Setting User's Logo Advanced1 Advanced2 About Reset All [ ]: Select [ Computer/DVI Audio Input : Computer/DVI Volume Treble Bass Reset : : : 15 0 0 Computer DVI - + - + - + Execute ]: Enter [Menu]: Exit 2.
Customizing Projector Features You can use the menu system to change the video signal input at certain ports, turn sleep mode on or off, adjust the network settings, change the language, and customize several other features. Image Setup Options Use these settings to change how the projector processes incoming video signals. Several of these settings should normally be left at the factory default setting (except for the Computer and BNC Input settings).
■ Progressive (in the Advanced1 menu) This setting should normally be left at its default setting (Video or Film/Auto). Converts interlaced signals to progressive signals. When set to OFF, interlaced signals are processed without conversion (available for video signals only). ■ BNC Sync Termination (in the Advanced2 menu) This setting should normally be left Off (for TTL input). If an analog (75-ohm) terminator is required, as for a switcher, change the setting to ON.
Miscellaneous Setup Options ■ No-Signal Msg. (in the Setting menu) Selects a screen color or image to display when the projector is not receiving a signal. The logo setting displays an image that you previously transferred to the projector (see page 78). ■ Sleep mode (in the Setting menu) When sleep mode is on, the projector turns off the lamp if it has not received any input signals for 30 minutes. Turn sleep mode off if you want the lamp to remain on all the time (this is the default setting).
Using the Projector’s Security Features To prevent unauthorized use of the projector, you can do the following: ■ Create an identifying user logo that is displayed at startup and/or when the A/V Mute button is pressed ■ Assign a password; this can be disabled for a set period if you want to loan the projector to someone ■ Disable the projector’s buttons; this is useful, for example, if you’re projecting in a classroom and you want to ensure that no one touches the projector’s buttons while you’re using
Creating Your Own Screen Logo You can transfer any image on your computer to the projector, and then use it as the startup screen and/or the screen that is displayed when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. The projector considers this image the “User’s Logo.” Follow these steps to capture the image and transfer it to the projector: 1. Display the image you want to use on the projector.
7. When you see this screen, select a zoom rate (display size), and then press Enter. note If the User’s Logo Protect option has been set to ON, the No-Signal Msg. and A/V Mute settings cannot be changed. You need to turn the protect function off first. See page 81 for details. User's Logo Set the zoom rate. Zoom rate: 100% 200% 300% 8. When you see the message Save image as user’s logo?, select Yes and press Enter. Saving the logo takes about 15 seconds.
5. Select the screen(s) on which you want your image to appear: ■ Select No-Signal Msg. if you want to display your image (instead of a blank screen) when there is no video signal incoming from the currently selected source. Then select Logo. ■ Select A/V Mute if you want your image to appear when you press the A/V Mute button. Then select Logo and press Enter. 6. To display the logo as the startup screen, select the Setting menu. 7. Select No-Signal Msg. and press Enter.
The password will be displayed as ****. After you enter the last digit, a confirmation screen appears. Enter the password again. 5. After you finish setting the password, press the Esc button to return to the Password Protect menu. 6. Press the Num button on the remote control to turn off the numeric keypad. Make a note of the password and keep it in a safe place in case you forget it. Turning On Password Protect and User’s Logo Protect 1.
note If you lose the remote control, you will not be able to enter the password, so keep the remote control in a safe place at all times. 6. Press Menu to close the Password Protect menu. 7. Turn off the projector and unplug the power cord to enable password protection. When you turn the projector on again, you will need to enter a password. Follow the instructions in the next section.
If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 121. If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it. Disabling the Projector’s Buttons When you enable the Operation Lock function, all the projector’s buttons are disabled except for the P Power button. 1. Press the Menu button. 2.
Fine-tuning the Projector
1 Managing the Projector from a Remote Computer Y our projector’s Easy Management software lets you monitor and control your projector(s) from a remote computer in several ways: ■ Use EMP Monitor to see your projectors’ status, switch image sources, and control basic settings. ■ Use EMP NetworkManager to receive e-mail notifications alerting you to possible problems. ■ Use a network management utility running SNMP, such as HP OpenView,™ to manage your facility’s equipment from a pre-existing system.
Installing the Easy Management Software The projector software CD-ROM includes the software you need to use the projector’s EMP Monitor and EMP NetworkManager. System Requirements Before you install the software, make sure your computer meets these requirements: note The Easy Management software cannot be installed on Macintosh systems. ■ Microsoft® Windows 98 SE, XP, 2000, Me, or NT 4.
2. Click Install to install both EMP Monitor and EMP Network Manager. 3. Follow the on-screen instructions to install the software. 4. When you’re finished, click Exit. Once installed, you can access these programs from your computer’s Start menu. Connecting and Configuring the Projector note If you don’t want to install both programs, click Custom, select the program you want to install on the next screen, and click Install.
3. Press the Menu button on the remote control and select Network from the Advanced2 menu. Video Brightness Control : High Audio Effect Projector ID Network Setting COM Port Low :1 Set Select Network Set Advanced1 : RS-232C USB Auto setup : ON OFF BNC Sync Termination : ON OFF Advanced2 Reset User's Logo Execute About Reset All note If you’re a network administrator, you can use the SNMP option to enter a trap IP address.
■ To change the network addresses from the projector’s control panel, press the right and left arrow buttons to select the part of the address you want to enter, then use the up and down arrow buttons to increase or decrease the numeric value. Select the part of the address to change Increase or decrease the value When you finish changing an address in the network menu, press the Enter button (on the remote control) or the Auto/Enter button (on the projector). This stores the value. 6.
Opening and Closing EMP Monitor To start EMP Monitor, click Start > Programs or All Programs > EPSON Projector > EMP Monitor. If you’ve added the program to the Startup programs folder (see page 95), then it may already be open. If so, click the icon in the system tray on the lower-right corner of your screen to display the EMP Monitor window: Click here to start EMP Monitor To close EMP Monitor, right-click the program icon shown above, then select Exit.
2. Click Register projector as shown. You see this screen: Click here note 3. Click Auto detect to locate projectors currently operating on the network. Or click Manual registration and enter the projector’s name and network address. Any projectors found on the network are listed as shown below: If Auto detect fails to find the projector, your projector may not be connected or configured correctly for the network. See page 87. Click here 4.
You see this screen with a list of all registered projectors. note To delete a projector from the list, highlight the projector name, and click Delete. 5. Click Close.
Monitoring Your Projectors The EMP Monitor screen lets you monitor your projectors using the Status, Video Source, and Error icons shown below. This lets you see which projectors are currently being used, from which source (or port) they are projecting an image, and if a problem occurs. note To monitor a projector when it’s in standby mode (plugged in but not turned on), you must select Network ON as the Standby Mode setting in the projector’s menu system (see page 75). You can monitor up to 64 projectors.
The following table explains the meaning of the video source icons: Video source icons Computer, Computer1, or InputA Computer2 or InputB S-Video Video D4 (Digital) DVI or HDMI (Digital) The following table explains the meaning of the error icons (see Chapter 7 for recommended solutions to problems): Error icons Lamp replacement notification (the lamp is nearing the end of its life; see page 104) High-speed cooling in progress (the projector is getting too hot but continues to operate) Lamp out or lamp
Controlling Your Projectors The control buttons in the upper-right let you turn on and off the projectors and select video sources. (Hold the mouse pointer over a button to see a description of its meaning.) Make sure you’ve selected the projector you want to operate (with the mouse pointer) before clicking one of the buttons.
Using EMP NetworkManager You can use EMP NetworkManager to send out messages by e-mail, notifying you when a problem occurs with a projector. Before running EMP NetworkManager, make sure you’ve installed the software as described on page 86. Then follow the steps below to create e-mail settings for each projector you want to monitor. Selecting the Projectors to Monitor 1. To start EMP NetworkManager, click Start > Programs or All Programs > EPSON Projector > EMP NetworkManager.
3. Enter the projector’s IP address and click Add. The projector’s icon is added to the EMP NetworkManager screen. 4. Click Connect to connect the projector to the network. Setting a Password You can set a password to restrict access to each projector from EMP NetworkManager: 1. Right-click the icon of the projector whose password you want to set, then select Change Password. 2. Enter a password up to 14 characters in length. Creating the E-Mail Settings 1.
note The projector must be plugged in (projecting or in standby mode) for you to be able to connect to it. To access a projector in standby mode, you must select Network ON as the Standby Mode setting in the projector’s menu system (see page 75). Remember that when Standby Mode is set to Network ON, the exhaust fan continues to operate after the projector has cooled down. This is normal. 3. EMP NetworkManager connects to the projector, and you see this screen: 4.
6. Select ON for the Mail Notification setting. 7. Enter the IP address and port number of the SMTP server used for sending e-mail. (The port’s default setting is 25, but you can enter any number from 1 to 65535.) 8. Enter up to three e-mail addresses where you want the event notification messages to be sent. 9. Click the Setting a Notification Event button next to each address, then select the conditions under which you want a message to be sent. 10. Click OK, then click OK again on the next screen.
Managing the Projector from a Remote Computer
1 Maintaining the Projector Y our projector needs little maintenance. All you have to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. ■ Use a canister of compressed air to remove dust. ■ To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface. Remove the cap before cleaning Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.
Cleaning the Air Filters and Vents Clean the air filters and air vents after every 100 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. Follow these steps: 1. Turn off the projector and unplug the power cord. 2. To clean the intake vents, Epson recommends using a small vacuum cleaner designed for computers and other office equipment.
4. If the dirt is difficult to remove or a filter is broken, replace the filters as in the following section. Contact your dealer or call Epson at (800) 873-7766 in the United States to obtain new ones. In Canada, please call (800) 463-7766 for dealer referral. Replacing the Lamp and Air Filters note When you get a replacement lamp for your projector, new air filters are included. You should replace the filters when you replace the lamp.
4. Turn the projector over and remove the air filters at the side and bottom of the projector. . . . and here Slide the filter up here . . . 5. Insert the two new air filters. They should click into place. 6. Insert the screwdriver supplied with the spare lamp, or some other flat-tipped screwdriver, into the space beside the air vent. Gently slide the lamp cover until the arrow on the cover is aligned with the arrow on the projector. Then lift the cover off.
7. Loosen the two screws holding the lamp in place (you don’t need to remove them). 8. Grasp the wire handle as shown and pull the lamp straight out. note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. When you get a replacement lamp for your projector, new air filters are included. This is a good time to install them (see page 104). 9. Gently insert the new lamp. 10.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Plug the projector in and turn it on. 2. Press the Menu button on the remote control (or on the projector’s control panel). You see the main menu. 3. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight About, then press Enter.
Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent injury or damage: note ■ When hand-carrying the projector, you should use the handle to lift it only a short distance (for example, to set it on a table). ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
1 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or on the remote control. The following choices are available: ■ Problems with image ■ Problems with sound ■ Language change Follow these steps to get help: 1. Press the blue ? Help button on the projector. Help button on projector You see the Help menu: Help Menu No image appears on the screen. The image is unsteady.
Checking Projector Status If your projector isn’t working correctly, first turn it off, wait for it to cool (the P Power light stops flashing orange), and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
Status lights Light Status Description flashing red Rapid cooling in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises too high again. Make sure there is plenty of space around and under the projector for ventilation, and that the air filters and vents are clear. flashing orange red The projector is overheating, which turns the lamp off automatically. Wait until the cooling fan stops, then unplug the power cord.
The Power light is flashing orange and you cannot turn on the projector. The lamp is cooling down. Wait until the light turns off and then press the Power button to turn on the projector. The Power light does not come on. Make sure the power cord is connected securely both at the power outlet and the projector. If you have just replaced the lamp, make sure the cover is securely fastened.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the P Power light is green, not flashing, and the lens cap is off. ■ The projector may be in sleep mode. If the P Power light is orange, press the Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may still be cooling down. Wait until the P Power light stops flashing and remains orange; then press the Power button again.
If you’re using a PC notebook: ■ Hold down the Fn key on the keyboard and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your notebook’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
The message Not Supported is displayed. ■ Make sure the correct Input Signal is selected in the Setting menu (see page 74). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200), and the frequency is supported by the projector (see page 128). If necessary, change your computer’s resolution setting as described in the following section. Only part of the computer image is displayed. ■ Press the Auto button on the remote control.
The image isn’t square, but keystone-shaped. ■ If the top or bottom of the image is broader, press the Sync + or Sync – button on the projector until the image is square. ■ If the projector is angled toward the screen from the left or right, the image will be broader on one side. Center the projector in front of the middle of the screen, facing the screen squarely. If this doesn’t work, press the Tracking + or Tracking – button on the projection until the image is square.
■ Make sure the projector is within the recommended projection distance (2.5 to 36.5 feet). ■ Adjust the Sharpness setting on the Video menu (see Chapter 4). When you change video settings, you should be able to see the effect on the screen immediately. If you’re projecting from a computer, you may also need to adjust the tracking and sync as described in the next section. If you don’t like the new settings, you can always select Reset to return to the factory default settings.
3. Adjust the Sync setting to increase the sharpness of the image. The colors of the image are not right. ■ If you’re displaying a computer image, use the Color Mode option in the projector’s Video menu to adjust the color. If you’re displaying video, adjust the Color, Tint, and Color Mode settings on the Video menu. ■ Try changing the Color Adjustment setting on the Advanced1 menu. ■ Check your computer display settings to correct the color balance.
Solving Easy Management Problems You don’t see your projector in the EMP Monitor window. ■ Make sure that you’ve connected the projector to the network and configured it correctly; see page 87. Also, make sure you’ve registered the projector with EMP Monitor. See page 90. ■ Make sure that Standby Mode in the Advanced1 menu is set to Network ON. ■ If the computer you are using is running Windows XP, 2000, or NT 4.x, you must be logged in as the Administrator. ■ Try restarting your computer.
Where To Get Help Internet Support Visit Epson’s support website at http://support.epson.com and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Visit http://www.presentersonline.com to access tips, templates, and training for developing successful presentations.
Solving Problems
A Appendix A: Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
warning When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use any type of oil or lubricant. These may cause the projector casing to crack and the projector may fall, causing serious injury and serious damage to the projector. If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt it down to position the image on-screen. This causes the image to lose its square shape.
A Appendix B: Technical Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels Diagonal: 1.0 inch (25.4 mm) Lens F=1.7 to 2.3, f=28 to 37 mm Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 24 bit, 16.7 million colors Brightness 4000 lumens (High brightness mode) 3500 lumens (Low brightness mode) Contrast ratio 700:1 Image size 30 to 300 inches Projection distance 2.5 to 36.5 feet (0.
Projection Lamp note Turn off this product when not in use to prolong the life of the projector. Type UHE (Ultra High Efficiency) Power consumption 250 W Lamp life Up to 2000 hours (high brightness mode) Up to 3000 hours (low brightness mode) Part number V13H010L22 Remote Control Range 33 feet (10 meters) Batteries (2) Alkaline size AA Mouse Compatibility Supports USB Dimensions Height 4.6 inches (117 mm), feet retracted Width 16.5 inches (419 mm) Depth 12.8 inches (325 mm) Weight 12.
Environmental Temperature Operating: 41 to 104 °F (5 to 40 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Operating altitude 0 to 7,500 ft (0 to 2,286 m) Safety United States FCC 47CFR Part 15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No. 60950 CE Marking Directive 73/23/EEC Directive 89/336/EEC EN 55022, EN 55024 Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. As noted below, some images are automatically resized to display in one of the projector’s “native” formats (such as XGA).
Mode Refresh Rate (Hz) Resolution UXGA—60 UXGA—65 UXGA—70 UXGA—75 UXGA—80 UXGA—85 60 65 70 75 80 85 1600 × 1600 × 1600 × 1600 × 1600 × 1600 × MAC13 MAC16 MAC19 MAC21 67 75 75 75 640 × 480* 832 × 624* 1024 × 768 1152 × 870* NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM 60 60 50 50 60 60 50 — — — — — — — HDTV (720p) HDTV (1080i) 60 60 1024 × 576* 1024 × 576* SDTV (480i) SDTV (480p) SDTV (625i) SDTV (625p) 60 60 50 50 1024 × 1024 × 1024 × 1024 × *The 1200* 1200* 1200* 1200* 1200* 1200* 768 76
Appendix B: Technical Specifications
A Appendix C: Notices This appendix includes safety instructions and other important information about your Epson PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
■ Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. ■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Epson America, Inc. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID.
Appendix C: Notices
Index A C A/V Mute, 57, 78 to 80, 114 About menu, 107, 113 Accessories, 15, 121 Adapter, Macintosh, 14, 15, 30 Air filter cleaning, 103 to 104 ordering, 15 replacing, 104 to 106 Alerts, email, 96 to 99 Anti-theft device, 15, 19 Aspect ratio, 125 Audio adjusting volume, 47, 73 cable, 10, 34 connecting equipment, 33 to 34 menu, 73 problems, troubleshooting, 119 turning off (using A/V Mute), 57 Auto button, 47 Cables BNC, 23, 25, 28 component-to-VGA, 15 composite (RCA), 20 to 21 DVI, 15, 29 illustrations, 1
D H Declaration of Conformity, 134 Default password, 77 Default settings, restoring, 67 Desktop adapter, Macintosh, 14, 15, 30 Direct Power ON, 76 Distance from projector to screen, 18, 125 Documentation, 11 DVD player, connecting, 20 to 25 DVI cable, 15, 29 DVI port, connecting to, 29 HDTV formats, supported, 129 Height of image, adjusting, 43 Help system, using, 110 Help, Epson, 11, 121 HP OpenView, 85 E Easy Management configuring the projector, 87 to 89 monitoring the projector, 89 to 95 problems, 1
Language setting, 76 Lens cleaning, 102 ordering, 15 specifications, 125 Lights, status, 111 to 113 Logo creating, 78 to 79 displaying, 79 to 82 M Macintosh desktop adapter, 14, 15, 30 Manuals, 11 Menus About, 107, 113 Audio, 73 default settings, restoring, 67 User’s Logo, 78 to 79 using, 66 to 67 Video, 68 to 70 Monitor, connecting external, 32 Monitoring projector EMP Monitor, 89 to 95 HP OpenView, 85 receiving e-mail alerts, 96 to 99 Mouse connecting cable for remote, 31 using remote control as, 62 N N
Projecting without screen, 48 to 49 Projection distance, 18, 125 Projection lamp, see Lamp Projector carrying case, 15, 108 cleaning, 102 connections, see Connecting projector disabling buttons, 83 distance from screen, 18, 125 ID, setting, 63 installing, 123 to 124 lamp specifications, 126 monitoring remotely, 85 to 99 multiple projectors, controlling, 63 to 64 options, 15 password protection, 77, 80 to 83 positioning, 18 to 19 resolution, 125 security features, 77 to 83 specifications, 125 to 127 transpor
Sound adjusting, 47, 73 troubleshooting, 119 Source previewing, 56 selecting, 38, 55 to 56, 74 to 75 viewing, 113 Speaker, specifications, 125 Speakers, connecting, 34 Specifications brightness, 125 dimensions, 126 electrical, 126 environmental, 127 general, 125 lamp, 126 lens, 125 remote control, 126 resolution, 125 safety, 127 Standby Mode setting, 75, 93, 95, 98 Startup screen creating, 78 to 79 displaying, 79 to 82 user’s logo, see User’s Logo Status lights, 111 to 113 Support, Epson, 11, 121 S-Video ca
W Wall Shot, 48 to 49 Warning lights, 111 to 113 Warranty, 12, 136 to 137 Wireless, mouse, 31, 62 Z Zoom ratio, 125 Zooming image, 42, 57 to 58 144 Index
Front/Top Focus ring Zoom ring Temperature light Lamp light Remote Control Power light Control panel Page up and down Change slides in PowerPoint Air exhaust vent E-Zoom button Enlarges section of image Remote control receiver A/V buttons Control image and sound Foot release lever Air filter Adjustable foot Handle Light button Illuminates remote control buttons Enter and ESC Use as mouse buttons or to make menu selections Lens cover Menu button Activates menu system Back USB port Control port f
Front/Top Focus ring Zoom ring Temperature light Lamp light Remote Control Power light Control panel Page up and down Change slides in PowerPoint Air exhaust vent E-Zoom button Enlarges section of image Remote control receiver A/V buttons Control image and sound Foot release lever Air filter Adjustable foot Handle Light button Illuminates remote control buttons Enter and ESC Use as mouse buttons or to make menu selections Lens cover Menu button Activates menu system Back USB port Control port f
