® PowerLite Home Cinema 8350/8700 UB Home Theater Projector User’s Guide
Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.
Contents Introduction Projector Parts Remote Control Optional Accessories Registration and Warranty Using This Manual Setting Up the Projector Choosing a Location Installing the Projector Connecting the Cables Connecting Video and Computer Equipment Making Other Connections Installing Batteries in the Remote Control Turning the Projector On and Off Turning On the Projector Turning Off the Projector Selecting the Image Source Positioning the Image Making Basic Adjustments Focusing and Zooming Choosing the
Making Detailed Adjustments Using the Menu System Changing How the Menus Display Adjusting the Picture Quality Input Brightness Settings Sharpness and Picture Quality Settings Color Settings Adjustments for Computer Images Selecting Memory Settings and Resetting the Projector Selecting Memory Settings Creating Memory Settings Renaming Memory Settings Deleting Saved Memory Settings Resetting the Projector Customizing Projector Features Image Sizing Screen Options Other Setup Options Maintenance Cleaning the
Where to Get Help 64 Specifications 65 65 65 66 66 66 67 67 67 69 General Lamp Remote Control Dimensions Electrical Environmental Safety Compatible Video Formats ESC/VP21 Command Codes Notices Important Safety Information FCC Compliance Statement Declaration of Conformity Epson America, Inc.
Introduction The PowerLite® Home Cinema 8350/8700 UB projector lets you enjoy theater-quality images in the relaxing environment of your own home.
Projector Parts Front Control panel (top) Vertical lens shift dial Lamp cover Control panel (side) Zoom ring Ventilation slots Infrared receiver Horizontal lens shift dial Adjustable foot Focus ring Lens cover Back Infrared receiver Component video port Control (RS-232C) port PC port S-Video port HDMI ports Lamp cover release Trigger out port Kensington® lock port Main power switch Air intake (filter) Video port Cable holder AC power inlet Introduction 7
Bottom Mounting bracket attachment points Optional cable cover attachment points (brass colored) Projector Control Panel Top control panel Side control panel Menu navigation button Power button Source button Switches the video input source Warning lights 8 Introduction Menu button Displays the menus Enter button Selects menu items or opens the line menu Esc button Exits the current menu item
Remote Control Power button Turns projector on or off Default button Restores default settings when menu is displayed Menu navigation buttons Memory button Recalls custom picture settings RGBCMY button Adjusts the hue, saturation, and brightness for each color Gamma button Adjusts the gamma values of the screen display Pattern button Displays test patterns to adjust the image Illumination button Lights the remote control buttons for easy viewing Source buttons Switch between equipment connected to the
Optional Accessories Epson provides the following optional accessories for the projector: Product Part number Replacement lamp V13H010L49 Air filter replacement V13H134A21 Kensington security lock (anti-theft device) ELPSL01 Cable cover V12H003002 Projector mount ELPHB550 Anamorphic lens kit (Home Cinema 8700 UB only) ELPALK2 In addition to the accessories listed above, 1-year and 2-year extended service plans are available.
Using This Manual This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information. Please follow these guidelines as you read through the manual: WARNING: Must be followed carefully to avoid bodily injury. Caution: Must be observed to avoid damage to your equipment. Note: Contains important information about your projector.
Setting Up the Projector Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image. Choosing a Location You can install the projector for the viewing setups shown below, as well as rear projection.
Ideally, keep the projector level and place it at a height so its lens is centered between the top and bottom of the screen, as shown below. If this is not possible, use the lens shift dials to reposition the image. As a rule of thumb, you can use lens shift to move the image up or down by nearly its full height, and left or right by about one-half its width (for details, see page 25).
The size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may differ. Use these tables as a guide for projector placement: 16:9 aspect ratio Diagonal image size Projection distance (width × height) Offset A Offset B Horizontal Offset 2.8 to 6.2 feet 0.87 to 1.88 m 30 in. (26 × 15 in.) 76.2 cm (66 × 37 cm) 6.8 in. 17 cm 21.5 in. 55 cm –11.5 to 11.5 in. –29 to 29 cm 3.8 to 8.3 feet 1.
4:3 aspect ratio (continued) Diagonal image size Projection distance (width × height) Offset A Offset B Horizontal Offset 14.4 to 30.7 feet 4.40 to 9.36 m 120 in. (94 × 71 in.) 305 cm (240 × 180 cm) 33.0 in. 85 cm 105.0 in. 268 cm –56.5 to 56.5 in. –143 to 143 cm 18 to 38.4 feet 5.51 to 11.71 m 150 in. (118 × 91 in.) 381 cm (300 × 230 cm) 41.7 in. 106 cm 131.7 in. 334 cm –70.6 to 70.6 in. –179 to 179 cm 24.2 to 51.3 feet 7.36 to 15.62 m 200 in. (161 × 118 in.) 508 cm (410 × 300 cm) 55.6 in.
Installing the Projector To install the projector, you first need to determine the location, based on the size of your screen (maximum diagonal image size). Use the tables on page 14 as a guide to positioning the projector. To suspend the projector from a ceiling, you will need the optional projector mount designed for the projector. See page 10 for ordering information. Follow the instructions included with the mount to install the projector.
The following illustrations show the dimensions of the projector: Center of lens 5.4 in. 36 mm 0.5 in. 2.3 mm 2.8 in. 72 mm 5.8 in. 148.3 mm 0.2 in. 4.5 mm 5.2 in. 131 mm 17.7 in. 450 mm 11.8 in. 300 mm 3.0 in. 75 mm 5.9 in. 150 mm 2.2 in. 56 mm 1.8 in. 45 mm 5.3 in. 134.7 mm 6.3 in. 160 mm 15.3 in. 389.
Connecting the Cables Connecting Video and Computer Equipment You can connect the projector to many types of video equipment, such as a Blu-ray Disc™/DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple® Macintosh® system. For details on compatible video formats, see page 67.
For best results, connect your video equipment to the HDMI port, if possible. If your equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): Component (for component video), S-Video, or Video (for composite video).
Making Other Connections Connect the power cable and other cables described below, depending on how you plan to use the projector. ■ Plug the power cable into the projector and a grounded electrical outlet. ■ The Trigger out port outputs a 12-volt DC signal when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use.
Installing Batteries in the Remote Control The remote control uses two AA batteries. WARNING: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover. 2. Insert two new AA batteries as shown. 3. Insert the tab on the cover and press it down until it clicks into place. Aim the remote control at the screen, or at the front or back of the projector. Make sure you are within 30 feet of the projector.
4. Press the Ppower button on the remote control or projector. Remote control Projector Note: To prevent children from turning on the projector, you can use the Child Lock feature. See page 32 for details. If you’ll be using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure. See page 49 for details. The projector takes about 30 seconds to warm up and display an image.
Selecting the Image Source The source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a Blu-ray Disc/DVD player, cable or satellite box, or video game console). Press the Source button on the remote control that corresponds to the port to which your video source is connected. If you press the source button on the projector, you see a list of available sources.
Positioning the Image If the image is not centered on the screen, use the horizontal and vertical lens shift dials to adjust its position. Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position. Horizontal lens shift dial Vertical lens shift dial Note: You can display a test pattern to help adjust the image position by pressing the Pattern button on the remote control. Press the Esc button to turn off the test pattern.
The image cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the width of the image.
Making Basic Adjustments Follow the instructions in this chapter to make basic adjustments to the image shape, size, color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33. Focusing and Zooming Use the focus ring to sharpen the image. Use the zoom ring to reduce or enlarge the image.
Choosing the Aspect Ratio In many cases, video signals are automatically resized to fit on your screen when Auto is selected as the Aspect setting. You may need to change the size of the image (or aspect ratio) for certain image types by pressing the Aspect button on the remote control. Aspect button Select one of these settings: ■ Normal for standard TV broadcasts, computer images, or images with a 4:3 aspect ratio. ■ Full for images recorded in squeeze mode.
Choosing the Color Mode You can change the Color Mode to automatically adjust brightness, contrast, and color, letting you quickly optimize the projected image for various lighting environments. You can also select a different color mode for each input source—which is useful if you view different types of images from different sources.
Advanced Color Adjustments To further customize the color and image quality, you can adjust the gamma and individual RGBCMY color tones using the RGBCMY and Gamma buttons on the remote control. (Not available when x.v.Color is selected as the Color Mode.) RGBCMY Gamma Note: You can fine-tune these and other color and image quality settings using the projector’s menu system (see page 33). You can also save combinations of picture settings with the Memory feature for easy recall (see page 43).
Adjusting the Gamma Setting You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas. Gamma presets make minor adjustments to mid-tone values. The larger the gamma preset, the lower the midtone values. Changing these settings affects contrast which can be seen as a blur in bright areas.
Adjusting RGBCMY Use this feature to adjust the hue, saturation, and brightness for each of the red (R), green (G), blue (B), cyan (C), magenta (M), and yellow (Y) color components. 1. Press the RBGCMY button. You see the following displayed on the screen: 2. Use the u or d button on the remote control to select the color you want to adjust, and press the Enter button. 3. Select the Hue, Saturation, or Brightness for that color, and use the l or r button to make the adjustment. 4.
Locking the Projector The projector includes two lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision. To access the lock settings, follow these steps: Menu navigation buttons 1. Press the Menu button on the remote control. 2. Use the menu navigation buttons to open the Settings menu. 3.
Making Detailed Adjustments You can use the projector’s on-screen menus to make detailed adjustments to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features. Using the Menu System You can access the menu system either from the remote control or the buttons on the projector’s control panel. You can access the full menu or a line menu that lets you change selected settings.
3. Press the u, d, l, or r button to change settings as necessary. You may have to press the Enter button to confirm your choice. 4. When you’re finished, press the Esc button to return to the previous menu or press the Menu button to exit the menu system. To display one of the line menus, press the Enter button. You see a display like this at the bottom of the image: 1.
Changing How the Menus Display Use these options to control how the menus display. ■ Language Settings > Language Select from 21 languages to use in the menu system. ■ Menu Position Settings > Display > Menu Position Use the arrow buttons to choose a position on the screen for displaying the menu. ■ Menu Color Settings > Display > Menu Color Select a color scheme for displaying the menus.
■ Brightness Image > Brightness Adjust the brightness so it’s suitable for your viewing conditions. For example, if you’re projecting in a brightly lit room or onto an especially large screen, you may need to increase the brightness. Decrease the brightness for dark rooms or small screens; this also reduces power consumption and fan noise, and helps to prolong the life of the lamp. ■ Contrast Image > Contrast This setting adjusts the difference between bright and dark areas.
■ HDMI Video Range Signal > Advanced > HDMI Video Range Note: This setting can be used only when HDMI 1 or HDMI 2 is selected as the image source (see page 23). This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). If your video equipment has an HDMI port and you’ve connected it to the projector using an HDMI cable, set the level of the projector to match that of the video equipment.
■ Progressive Signal > Progressive Converts interlaced to progressive signals. The projector uses 3D DigiScan™ HD Circuitry Processing for video-sourced images. For film-sourced images, you can select from 2-2, 2-3, or 4-4 pulldown detection, depending on your model. Leave the setting on Film/Auto for viewing movies on a player that produces interlaced output. Select Video for watching videos captured with a video camera.
■ Block NR (Home Cinema 8700 UB only) Signal > Advanced > Block NR Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28) or with a signal input through the PC port. This setting reduces block noise that can appear when projecting MPEG images that have been compressed at a low bit rate.
Color Settings If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the remaining settings. Most color settings are stored separately for each image source and color mode.
■ RGB Image > Advanced > RGB Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). Use the RGB settings to fine-tune the color of the image. You can adjust the offset and gain for each signal color (red, green, and blue). Use Offset to adjust darker shades and Gain for the lightest shades. ■ RGBCMY Image > Advanced > RGBCMY Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28).
■ Color Gamut (Home Cinema 8700 UB only) Image > Advanced > Color Gamut Note: The Color Gamut setting can only be used when the Color Mode is set to THX (see page 28). You can select from three different color gamut settings according to the source material and locale. Select SMPTE-C for standard definition (USA, Canada, and other regions using NTSC), EBU (PAL) for Europe, or HDTV (all regions).
■ Tracking Signal > Tracking Adjust the tracking to eliminate vertical bands. It is easiest to adjust the tracking when the image contains a lot of fine detail (such as black text on a white background). ■ Sync. Signal > Sync. Adjust the synchronization to eliminate blurriness. For best results, make sure the tracking is properly adjusted first.
Creating Memory Settings Memory settings can be used to store most of the picture quality settings on page 37 and color settings on page 40. Before saving them to memory, adjust the settings to the desired levels. 1. Press the Memory button on the remote control. 2. Select Save Memory. 3. Select the memory name you want to use, then press the Enter button to save your settings. Note: Saved settings are indicated by a green highlight next to the memory name.
Deleting Saved Memory Settings You can clear all your memory settings at once. 1. Press the Menu button on the remote control. 2. Open the Reset menu, then select Reset Memory. 3. Select Yes, then press the Enter button to delete the memory settings. Note: You can delete memory settings one at a time with the Erase Memory setting under the Memory menu. Resetting the Projector If the image quality isn’t what you expect, one or more settings may be adjusted improperly.
3. Do one of the following: ■ Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero. You should reset the lamp timer only when you install a new projector lamp. See page 56 for more information. ■ Select Reset Memory to clear all memory settings. ■ Select Reset All to return all projector settings to their original defaults (except Component, Save Memory, Language, and Lamp Hours).
■ Zoom Caption Pos. Signal > Zoom Caption Pos. Lets you adjust the shape and position of the image so that subtitles are visible (available only if the aspect ratio has been set to Zoom). Use Zoom Size to adjust the proportions of the image, and Zoom Caption Pos. to move the image up or down. Adjust overscan before changing the zoom position.
■ Video Signal Settings > Input Signal > Video Signal Leave this setting on Auto so the projector can automatically interpret the format, such as NTSC or PAL (for standard TV formats). ■ Component Settings > Input Signal > Component Change this setting to match the type of equipment connected to the Component port. For component video, select Auto to let the projector automatically interpret the signal; or select YCbCr or YPbPr to manually select your video equipment’s signal.
■ Control Panel Lock Settings > Control Panel Lock Lets you disable all the buttons on the projector’s control panel to prevent the image from being accidentally changed once it is adjusted. See page 32 for more information. ■ High Altitude Mode Settings > High Altitude Mode Adjusts the speed of the fan so it can properly cool the projector at higher altitudes. Turn this setting on if you are using the projector at an altitude of 4921 feet (1500 meters) or higher.
Maintenance Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also may need to clean the air filter to prevent overheating. WARNING: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Projector Case Before you clean the case, turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case and dry it with a dry cloth. Caution: Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case.
7. Gently tap both sides of the air filter against a hard surface four or five times to remove loose dust from the air filter. Note: Do not tap the filter too hard. This can cause it to bend or break. 8. Use a small vacuum cleaner that is designed for computers and other office equipment to remove any remaining dust from the surface of the filter. If you don’t have one, gently clean the filter using a very soft brush (such as a clean artist’s paintbrush).
Replacing the Lamp The projection lamp lasts for up to 4000 hours. You can use the Info menu to check how long it’s been in use (see page 56). It’s time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate. ■ The projector’s lamp light flashes red at half-second intervals. ■ The message Replace the lamp appears on the screen when you start projecting. Lamp light Note: Lamp life results will vary depending on mode selected, environmental conditions, and usage.
5. Insert the screwdriver that came with the lamp (or a similar tool) into the slot on the back of the projector to release the lamp cover. Then lift up the cover to remove it. 6. Loosen the two screws securing the lamp (they don’t come all the way out). 7. Grasp the lamp as shown and pull it straight out. WARNING: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
8. Gently insert the new lamp and tighten its screws. Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.) 10. Reset the lamp usage timer, as described on page 56.
Resetting the Lamp Usage Timer After replacing the lamp, plug the projector back in, turn on the power switch on the back, and press the Ppower button. Then follow these steps to reset the lamp usage timer: 1. Press the Menu button on the projector or remote control. 2. Use the menu navigation buttons to open the Reset menu, then select Reset Lamp Hours. 3. When you see a confirmation prompt, highlight Yes and press the Enter button. 4. When you’re finished, press the Menu button to exit.
Storing the Projector If you need to store the projector for an extended time, do the following: ■ Make sure the temperature of the storage area is within 14 to 140 °F (–10 to 60 °C). ■ Attach the lens cover and retract the feet. ■ Remove the batteries from the remote control. ■ Pack the projector in its original packaging or equivalent. Transporting the Projector Note: Epson shall not be liable for any damages incurred during transportation. The projector contains many glass and precision parts.
Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector isn’t working correctly, first press the P power button, let the projector cool down, turn off the power switch on the back, and unplug the power cord.
Lights indicating a problem Light state Cause and solution All lights are off The projector is not receiving power. Make sure the power switch on the back of the projector is turned on and the power cord is connected securely at both ends. The temperature light flashes orange and the power light is flashing The temperature light is red High-speed cooling is in progress. If the temperature rises further, projection will stop automatically.
Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected and the power switch in back of the projector is turned on. Then wait a moment for the Ppower light to come on before pressing the Ppower button. ■ If you’ve set the Control Panel Lock, the control panel buttons are disabled; you must use the remote control to turn on the projector (see page 32).
You’re using a computer and no picture appears on the screen. If you’re using a Windows® laptop: ■ Press the function key that lets you display on an external monitor. It’s often labeled with an icon such as , but it may also be labeled CRT/LCD. You may have to hold down the Fn key while pressing it. Check your laptop’s manual or online help. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
The picture isn’t rectangular. ■ If the image looks like or , the projector has been placed off to one side of the screen and angled toward it. Face the projector straight ahead (instead of at the center of the screen), then use the horizontal lens shift dial to center the image (see page 24). ■ If the image looks like or , make sure the projector is not tilted up or down. The picture contains static or noise.
■ Fine-tune the colors with the settings listed on page 40. ■ If the picture looks dark, you may need to replace the lamp. Check the lamp usage timer to see how long the lamp has been in use (see page 56). Replace the lamp if it’s close to the end of its service life (see page 53). Solving Remote Control Problems The projector doesn’t respond to remote control commands.
Where to Get Help Internet Support Epson provides technical assistance 24 hours a day at epson.com/support (U.S.) or epson.ca/support (Canada). Here you can access troubleshooting information, download product documentation, and receive technical advice through e-mail. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector.
Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.74 inch (18 mm) wide Lens F=2.0 to 3.
Remote Control Range Approximately 30 feet (9 m) Batteries AA × 2 Dimensions Height 5.4 inches (136 mm), not including adjustable feet Width 17.7 inches (450 mm) Depth 14.2 inches (360 mm); not including lens protrusion Weight 16.1 lb (7.3 kg) (Home Cinema 8350) 16.5 lb (7.5 kg) (Home Cinema 8700 UB) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC: 3.1 A (Home Cinema 8350) 3.3 A (Home Cinema 8700 UB) 200 to 240 VAC: 1.3 A (Home Cinema 8350) 1.
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Operating altitude Up to 7500 feet (2286 meters); over 4921 feet (1500 meters), enable High Altitude mode in the Settings menu (see page 49) Safety United States FCC Part 15B Class B (DoC) UL60950-1 Canada ICES-003 Class B CSA C22.2 No. 60950-1 Pixelworks DNX™ ICs are used in this projector.
Component video Format/ Signal Refresh rate (Hz) Resolution SDTV 480i 576i 480p 576p 60 50 60 50 720 × 480 720 × 576 720 × 480 720 × 576 HDTV 720p 1080i 1080p 50/60 50/60 50/60 1280 × 720 1920 × 1080 1920 × 1080 Analog RGB (computer display) Signal Refresh rate (Hz) Resolution VGA 60/72/75/85 640 × 480 SVGA 56/60/72/ 75/85 800 × 600 XGA 60/70/75/85 1024 × 768 SXGA 70/75/85 60/75/85 60/75/85 1152 × 864 1280 × 960 1280 × 1024 WXGA 60 60 60/75/85 1280 × 768 1360 × 768 1280 × 800 MAC1
ESC/VP21 Command Codes You can use an AV controller with a 9-pin null modem serial cable to control the projector. You can download the complete ESC/VP 21 Communication Manual for home theater projectors from the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada).
Item Aspect ratio Command Normal ASPECT 00 Full ASPECT 40 Zoom ASPECT 50 Wide ASPECT 70 Anamorphic Wide (Home Cinema 8700 UB) ASPECT 80 70 Specifications
Notices Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■ Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
■ The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. ■ Allow the lamp to cool for one hour before replacing it. ■ Unplug the projector during lightning storms or when not in use for extended periods. ■ Don’t place the projector or remote control on top of heat-producing equipment. ■ If you use the projector in a country other than where you purchased it, use the correct power cord for that country.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Declaration of Conformity According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: Epson America, Inc. 3840 Kilroy Airport Way MS 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
parts assume the remaining warranty period of the product covered by this limited warranty. If Epson replaces the lamp as part of the warranty service, the replacement lamp carries the limited 90-day warranty stated above. What This Warranty Does Not Cover: This warranty covers only normal use in the United States, Canada or Puerto Rico. Twenty-four hours per day or other excessive continual use is not considered normal use. This warranty does not cover consumables such as filters.
Index Numerics 2-2 Pull-down, 39 4-4 Pull-down, 39 A Abs. Color Temp.
Epson accessories, 10, 64 Home Service, 10 PrivateLine Support, 11, 64 technical support, 11, 64 warranty, 10, 74 to 75 EPSON Super White setting, 36 ESC/VP21 command codes, 69 F FCC Compliance Statement, 73 Filter, see Air filter Flickering, 38, 62 Focus ring, 26 Frame Interpolation, 39 Image adjusting, 29 to 31, 35 to 43 changing aspect ratio, 27 inverting, 16, 47 positioning, 24 to 25, 46 resizing, 27, 46 selecting source, 23 size, 14 to 15 Image menu, 45 Image problems, 60 to 63 Image Size Calculator,
Memory settings creating, 44 renaming, 44 using, 43 Menu button, 9, 33 Menus available settings, 35 to 49 customizing display, 35 line menu, 9 using, 33 to 35 Message setting, 47 Mosquito NR, 38 Motion Detection, 38 Mounting projector, 16 Moving projector, 57 N No image, 60 to 61 Noise Reduction, 38 O Offset, color, 41 Overscan, 46 P Pattern button, 9, 24, 40 Picture problems, 60 to 63 Pixelworks, 67 Positioning image, 24 to 25, 46 Positioning projector, 12 to 15 Power Consumption setting, 37 PrivateLine
Skin Tone setting, 40 Sleep mode, 48 Source buttons, 8, 9 Source, selecting image, 23 Specifications compatible video formats, 67 to 68 dimensions, 66 electrical, 66 environmental, 67 general, 65 lamp, 65 remote control, 66 Startup screen, selecting, 47 Static, 62 Storing projector, 57 Super-resolution, 42 Support, 11, 64 S-Video connection, 18 Sync (Synchronization) setting, 42 Wide setting, 27 X x.v.Color setting, 28 Z Zoom Caption Pos.
