® ® EPSON PowerLite Cinema 200 Home Theater Projector User’s Guide
Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON product. EPSON is not responsible for any use of this information as applied to other products.
Contents Introduction 7 Registration and Warranty Projector Parts Projection Controls Optional Accessories Using This Manual Getting More Information 7 8 9 10 11 11 Setting Up the Projector 13 Choosing a Location Connecting the Cables Other Connections Displaying and Adjusting the Image Focusing and Zooming the Image Inverting and Mirroring the Image Selecting the Input Signal Setting Positioning the Image Performing Keystone Correction 13 15 16 17 17 18 18 19 19 Basic Operation 21 Turning On the
Making Adjustments 27 Using the Menu System Changing How the Menu Displays Adjusting the Image Quality Brightness and Contrast Settings Sharpness and Picture Quality Settings Color Settings Adjustments for Computer Images Saving and Resetting Menu Selections Creating Memory Settings Resetting the Projector Customizing Projector Features Image Sizing Screen Options Other Setup Options 27 28 29 29 30 31 32 33 33 34 35 35 36 36 Using Cinema Color Editor 39 Setting Up Your Computer System Requirements
Maintenance 49 Cleaning the Lens Cleaning the Projector Case Changing the Remote Control’s Batteries Cleaning and Replacing the Air Filter Replacing the Lamp Resetting the Lamp Usage Timer Storing the Projector Transporting the Projector 49 49 50 51 52 53 54 54 Problem Solving 55 What To Do When the Lights Flash Checking the Projector Status Solving Picture Problems Solving Remote Control Problems Where To Get Help 55 56 57 60 61 Specifications 63 General Lamp Remote Control Dimensions Electrical
Notices 69 Important Safety Information Remote Control Information FCC Compliance Statement Declaration of Conformity Epson America, Inc.
Introduction The EPSON® PowerLite® Cinema 200 projector lets you enjoy theater-quality images in the relaxing environment of your own home.
Projector Parts Vertical lens shift knob Control panel Horizontal lens shift knob Lamp cover Lens cover Ventilation slots Infrared receiver Adjustable foot S-Video port Input B (computer VGA port) Input A (component video) Control (RS-232C) port USB port Infrared receiver D4 port (used mainly in Japan) Trigger out port Kensington® lock port AC power inlet 8 Video port (composite video)
Projection Controls Menu navigation buttons Focus button Menu button Displays the on-screen menu Source button Switches the video input source Indicator lights Power button Aspect button Changes the picture’s aspect ratio Zoom button Esc button Exits the current menu item Keystone correction buttons Corrects the shape of a non-rectangular image On/Off buttons Menu button Displays the projector’s menus Memory button Recalls custom picture settings Color Mode button Optimizes viewing for different ligh
Optional Accessories EPSON provides the following optional accessories for the projector: Product Part number Replacement lamp (ELPLP28) V13H010L28 Air filter replacement (ELPAF04) V13H134A04 Ceiling mount ELPHB01 Kensington security lock ELPSL01 Projection screens: 50-inch portable screen 60-inch portable pop-up screen 80-inch portable pop-up screen ELPSC06 ELPSC07 ELPSC08 Macintosh® adapter set (includes monitor adapter and desktop adapter) ELPAP01 S-video cable ELPSV01 You can purchase ma
Using This Manual This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information. Please follow these guidelines as you read through the manual: Warnings: Must be followed carefully to avoid bodily injury. Cautions: Must be observed to avoid damage to your equipment. Notes: Contain important information about your projector.
Setting Up the Projector Follow the instructions in this section to choose a location for the projector, connect the cables, and display and adjust the image. Choosing a Location You can install the projector for various viewing setups, as shown below. Front/Ceiling Front Rear/Ceiling Rear If you install the projector in a rear or overhead position, you’ll need to flip and/or mirror the image by selecting the correct Projection option (see page 18).
If you place the projector off to the side, aim it straight ahead (rather than at the center of the screen), then use the horizontal lens shift knob to center the image. Do not place the projector farther to the left or right than the edge of the screen, or you will not be able to project a square (or rectangular) image. Vertical lens shift knob Horizontal lens shift knob The maximum size of the image is determined by the distance from the projector’s lens to the screen.
Connecting the Cables You can connect the projector to any type of video equipment, such as a VCR, DVD player, HDTV tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple® Macintosh system.
Connect your video or computer equipment to these ports: Connect a computer to this port (D4 used mainly in Japan) Connect video equipment to one of these ports If you connect to the Input A port, be sure to select the correct Input Signal setting for your equipment, or the image may not display properly (see page 18). Other Connections ■ Power cable Plug the power cable into the projector and a grounded electrical outlet.
■ Trigger out port This port outputs a 12-volt DC signal when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use. Connect to it using a 3.5-mm mini jack cable, as shown. Displaying and Adjusting the Image Make sure your video or computer equipment is turned on, then turn on the projector as described on page 21.
Inverting and Mirroring the Image If the image is displayed upside-down or backward, select the correct Projection option: 1. Press the Menu button on the remote control. 2. Use the menu navigation buttons to open the Setting menu, then open the Screen menu, and then select Projection. Menu button 3. Choose from these options: ■ Front if the projector is located in front of the screen (for example, on a table). ■ Front/Ceiling if the projector is located in front of the screen and mounted overhead.
Positioning the Image If the image is not centered on the screen, use the horizontal and vertical lens shift knobs to adjust its position. Note: You can display a test pattern to facilitate adjustment. Press the Pattern button on the remote control, then select Cross-hatching.
Basic Operation Make sure the projector is set up as described on page 13, then follow the instructions below to turn it on and display an image. Turning On the Projector 1. Remove the lens cap. 2. Press the On button on the remote control, or press the Power button on the projector. Turn on the projector Note: If this is your first time using the remote control, make sure batteries are installed as described on page 50.
Turning the Projector Off To turn off the projector, press the Off button on the remote control (or press the Power button on the projector twice). Let the projector cool while the Ppower light flashes red (about 30 seconds). Once the light stops flashing and stays on, it’s safe to unplug the projector. Caution: Turn the projector off when not in use. Continuous 24-hour-a-day use may reduce its overall life.
Choosing the Aspect Ratio Composite and S-video signals are sized automatically to fit on your screen when Auto is selected as the Aspect setting. If you’re viewing a component video signal, you may need to change the size of the image (or aspect ratio) by pressing the Aspect button on the remote control. ■ If your video source is connected to the projector’s Video or S-Video port, select Auto to automatically display your image in the correct size.
Choosing the Color Mode You can change the Color Mode to automatically adjust brightness, contrast, and color, letting you quickly optimize the projected image for various lighting environments. You can also select a different color mode for each input source—which is useful if you view different types of images from different sources. (For example, you might set the S-Video source to Living Room if it’s usually used for watching movies, and then set the Video source to Dynamic for playing video games.
Locking the Projector The projector includes various Lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision. To access the Lock settings, follow these steps: 1. Press the Menu button on the remote control. 2. Use the menu navigation buttons to open the Setting menu, then open the Operation menu, and then select Lock Setting. Menu button 3.
Making Adjustments You can use the projector’s on-screen menus to adjust the image quality, such as the brightness, contrast, sharpness, and color. You can also change how the menus display, sleep mode settings, and other projector features. Using the Menu System You can access the menu system either from the remote control or by using the buttons on the projector’s control panel. With the menu system, you can adjust any of the settings described in this chapter.
Changing How the Menu Displays Use these options to control how the menu displays on the screen. ■ Language Setting ! Language Select from nine languages to use in the menu system. ■ Menu Position Setting ! On-Screen Display ! Menu Position Use the arrow buttons to choose a position on the screen for displaying the menu. ■ Navigation Bar Setting ! On-Screen Display ! Navigation Bar Select whether to display the navigation bar, which prompts you on which buttons to push to choose menu options.
Adjusting the Image Quality Before fine-tuning the image using these adjustments, make sure you have already selected the best Color Mode for your picture and viewing environment, as described on page 24. The Color Mode adjusts various settings to approximately correct levels, simplifying your adjustment of the picture. Most image quality settings are saved independently for each input source (Video, S-Video, Input A, Input B).
■ White Level/Black Level Image ! Picture Quality ! Input Adjustment ! White Level/Black Level Adjust the White Level so that details in the brightest parts of the image are not washed out. Then adjust the Black Level so that shadow-level details are still visible in the darkest parts of the image. If you cannot access the White Level and Black Level settings, highlight Input button, then choose White Adjustment (the first item in the menu list) and press the Level/Black Level in the sub-menu.
Color Settings If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the last two settings. Note: You can also make color adjustments by attaching a PC or laptop to the projector and using the Cinema Color Editor software. See page 39.
Adjustments for Computer Images In addition to the settings described above, you can adjust the Tracking and Sync settings for analog RGB computer images. Normally, these settings are adjusted automatically by the projector. If you notice that the image is blurry or contains dark vertical bands, you may need to adjust the settings yourself. ■ Auto Setup Image ! Auto Setup Leave this setting on so that the projector automatically adjusts the tracking, sync, and position of the image.
Saving and Resetting Menu Selections Once you’ve adjusted the picture settings, you can save them as a group using the Memory feature. This lets you easily recall them, and switch from one group of settings to another. You can save up to six groups of settings. If necessary, you can use the projector’s reset options to restore its factory-default settings. You can clear all the settings, or just the settings in a specific menu.
Resetting the Projector If the image quality isn’t what you expect, one or more settings may be adjusted improperly. If necessary, you can restore the projector to its factory-default (original) settings. To restore the settings in a specific menu (such as the Image or Setting menu), open that menu, select Reset, and confirm as needed. The example below shows how to reset the Image menu: Open the Image menu . . . . . .
Customizing Projector Features Use the settings in this section to adjust the image size and position, suppress on-screen text, and select basic setup options. Image Sizing Before adjusting any of these settings, make sure you have already selected an appropriate aspect ratio for the type of picture you’re viewing (see page 23). ■ Output Scaling Setting ! Advanced ! Output Scaling For standard video formats, this setting lets you see the edges of the image that are not normally visible in the picture.
Screen Options ■ Message Setting ! On-Screen Display ! Message Turn this setting off if you want to prevent on-screen messages from appearing (such as the no-signal message, or the identifying text that appears when you switch between image sources or color modes). ■ Background Color Setting ! On-Screen Display ! Background Color Changes the screen that’s used when the projector is not receiving a signal or when you press the Blank button to temporarily stop projection.
■ Input Signal Setting ! Input Signal Adjust these settings for the type of equipment connected to the projector: Video Signal: Leave this setting on Auto so the projector can automatically interpret the picture (only affects images displayed through the Video or S-Video port). Input A: Change this setting to match the type of equipment connected to the Input A port. If necessary, check the label on your equipment to match the setting.
Using Cinema Color Editor You can use the Cinema Color Editor software that came with your projector to adjust each color in the picture individually. You can also use the software to operate the projector in place of your remote control, letting you switch image sources, adjust the picture’s aspect ratio, or change image quality settings. Once you’ve adjusted the picture to your liking, you can save your settings so you can easily recall them for future use.
Installing the Software Follow these steps to install the software: 1. Insert the Cinema Color Editor CD-ROM in your computer. 2. Turn off any anti-virus software that may be running, then click Continue. 3. Read the license agreement and click Agree. You see this screen: Not shown for Macintosh 4. Click Install and follow the on-screen instructions to perform the installation.
Connecting to the Computer Follow these steps to connect to your computer: 1. Connect the projector to your computer using either a USB cable (included with your projector) or an RS-232C (serial) cable. Note: You can use any standard (commercially available) USB or serial cable. Connect either a USB or RS-232C (serial) cable 2. Turn on the projector. 3. Make sure the projector’s COM Port setting is correct for the type of cable you’re using (see page 37).
Using Cinema Color Editor To start Cinema Color Editor, follow these steps: 1. Make sure the projector is connected and turned on, as described on the previous page. 2. Windows: Click Start, Programs, EPSON Projector, and then Cinema Color Editor. Macintosh: From the Applications folder on your hard drive, open the CCEditor folder and double-click Cinema Color Editor. You see this screen: Select your projector . . . . . . and click Connect 3.
Remote Control Operations You can use Cinema Color Editor to change the image source, adjust the aspect ratio, or turn the power off—just as you would from the remote control. 1. Click the Remote Control tab. Select Remote Control Turn off the power Change the image source (see page 22) Adjust the aspect ratio (see page 23) 2. Click one of the buttons for the options shown above.
Adjusting the Picture Quality You can use Cinema Color Editor in place of the projector’s menu system to adjust the image. 1. Click the Picture Quality tab. First, select Picture Quality Then click one of these buttons to access additional settings 2. Click one of the buttons shown above to access additional settings.
Adjusting the Color You can use the Color Adjustment settings to fine-tune the color of the image. If you select RGB as the color mode, you can adjust the offset, gamma, and gain for each signal color (red, green, and blue). Or select RGBCMY to adjust the hue and saturation for each of six colors. 1. Select Picture Quality, then click Adjustment of image. 1. Select Picture Quality 2. Click Adjustment of image 3. Select the color mode 4. Click Adjust 2.
Saving and Recalling Picture Settings Once you’ve adjusted the picture using Cinema Color Editor, you can save your settings in the projector’s memory. Then you can use the remote control (or Cinema Color Editor) to easily recall them for future use. To save your settings on the projector: 1. Select Picture Quality, then click Memory management and choose Register. 1. Select Picture Quality 3. Click Register 2. Click Memory management 2.
To use a memory setting you’ve saved on the projector: Access the projector’s memory settings either from the remote control (see page 33) or by using Cinema Color Editor as follows: 1. Select Picture Quality, then click Memory management and choose Select. 1. Select Picture Quality 3. Click Select 2. Click Memory management 2. Click the tab where the setting you want to use is stored (Standard or Advance). 1. Select Standard or Advance 2. Select the setting you want to use 3. Click Select 3.
Managing Your Settings In addition to your projector’s twelve memory settings (six standard and six advanced), you can store any number of settings on your computer’s hard drive. You can also use Cinema Color Editor to rename or delete memory settings stored on your projector. To save or recall settings on your computer: In Cinema Color Editor, open the File menu, then choose one of the following: ■ Save setting to store the current Cinema Color Editor settings on your computer’s hard drive.
Maintenance Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also need to clean the air filter periodically to prevent overheating. Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
Changing the Remote Control’s Batteries The remote control uses two AA batteries. If you suspect they are weak, take the remote control to a darkened room and press the illumination button. If the buttons on the remote control do not glow red, replace the batteries as described below. Warning: Keep batteries away from children. If a battery should be swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover. 2. Remove the old batteries and insert the new AA batteries as shown.
Cleaning and Replacing the Air Filter Clean the air filter on the bottom of the projector after every 100 hours of use. If it’s not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. 1. Turn off the projector and wait for the P power light to stop flashing. 2. Unplug the power cord and disconnect any cables. 3. Turn the projector over.
Replacing the Lamp The projection lamp lasts for up to 1700 hours (in low brightness mode) or 3000 hours (in high brightness mode). You can use the Info menu to check how long it’s been in use (see page 56). It’s time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate. ■ The projector’s warning light flashes red at half-second intervals. ■ The message Replace the lamp appears on the screen when you start projecting.
5. Loosen the two screws securing the lamp. 6. Grasp the lamp as shown and pull it straight out. 7. Gently insert the new lamp and tighten its screws. Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 8. Replace the cover and tighten its screws. (The projector won’t work if the lamp cover is open or loose.) 9. Reset the lamp usage timer, as described in the next section.
Storing the Projector If you need to store the projector for an extended time, do the following: ■ Make sure the temperature and humidity of the storage area are within the recommended range for the projector (14 to 140 °F [-10 to 60 °C] and 10 to 90% relative humidity). ■ Attach the lens cover and retract the feet. ■ Remove the batteries from the remote control. ■ Pack the projector in its original packaging or equivalent.
Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector isn’t working correctly, first turn it off, let it cool, and unplug it. Then plug the power cord back in and turn on the projector.
The warning light is flashing orange. High-speed cooling is in progress. If the projector gets too hot again, projection stops automatically. Make sure there is plenty of space around and under the projector for ventilation. Clean or replace the air filter if necessary (see page 51). The warning light is red. The projector is too hot, which turns off the lamp automatically. Let it cool for five minutes, then turn it back on.
Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected, then wait a moment for the P power light to turn orange before pressing the Power button. ■ If you’ve set the Key Lock, the control panel buttons are disabled; you must use the remote control to turn on the projector (see page 25). ■ If you’ve set the Child Lock, use the remote control or press and hold the Power button on the projector for at least 3 seconds to turn it on (see page 25).
utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the setting varies from computer to computer; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display or enabled. See your computer manual or online help for details. If you’re using a Macintosh with OS X: 1. Select System Preferences from the Apple menu and click Displays. 2. Click Detect Displays. 3.
The picture is upside-down or reversed. Change the Projection setting in the menu system (see page 36). Only part of the picture is displayed, or the picture is distorted. ■ Press the Aspect button to select a different aspect ratio (see page 23). ■ If the Aspect is set to Zoom, you may need to use the Zoom Caption option to see the top or bottom section of the screen (so that subtitles are visible). See page 35. ■ Check the Output Scaling to make sure it’s adjusted correctly (see page 35).
The picture is blurry. ■ Make sure the Input Signal is set correctly for your video equipment (see page 37). ■ There may be dirt on the lens. Clean the lens as described on page 49. ■ Adjust the focus (see page 17). ■ Make sure the lens is not fogged by condensation. If you’ve just moved the projector from a cold environment, wait a couple of minutes before using it. ■ Adjust the Sharpness setting (see page 30).
Where To Get Help EPSON provides technical assistance 24 hours a day at http://support.epson.com. Here you can access troubleshooting information, download product documentation, and receive technical advice through e-mail. To use the EPSON PrivateLine Support service, call (800) 637-7661 and enter the PIN on the EPSON PrivateLine Support card that came with your projector. This is the fastest way of speaking to a live representative, and it’s free.
Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.7 inch (18 mm) wide Lens F=2.1 to 2.8, f=21.4 to 31.7 mm Resolution (native format) 1280 × 720 pixels, 720p Brightness 1300 ANSI lumens maximum (Dynamic/Living Room color mode) Color reproduction 24 bit, 16.8 million colors Contrast ratio 800:1 Image size 30 to 300 inches (0.76 to 7.6 m) Projection distance 2.9 to 37 feet (0.9 to 11.3 m) Zoom ratio 1:1.
Dimensions Height 4.5 inches (114 mm) Width 17.3 inches (440 mm) Depth 12.6 inches (320 mm) Weight 11.8 lb. (5.3 kg) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 3.0 A 200 to 240 VAC, 1.4 A Power consumption Operating: 270 W max. Standby: 0.
Compatible Video Formats The projector supports analog video in NTSC, PAL, and SECAM formats, and it automatically adjusts to the incoming signal. It can receive these formats as composite video, S-video, or component video—which it accepts through the Video, S-Video, and Input A (Component) ports, respectively. The projector also supports digital video (SDTV, HDTV) and various monitor display formats.
Aspect Ratio Settings Images can be automatically resized to display at the projector’s native resolution (1280 × 720) when the Aspect setting is set to Auto. If necessary, you can select a different Aspect setting to optimize the image (see page 23). The resolution at which the image displays for a given setting depends on the currently active picture source, as listed below.
Computer monitor formats (analog RGB) Aspect setting Format Normal Zoom Squeeze Through Squeeze Through VGA 960 × 720 1280 × 720 1280 × 720 640 × 480 853 × 480 VESA 960 × 720 1280 × 720 1280 × 720 640 × 480 853 × 480 SVGA 960 × 720 1280 × 720 1280 × 720 800 × 600 1066 × 600 XGA 960 × 720 1280 × 720 1280 × 720 — — SXGA 960 × 720 1280 × 720 1280 × 720 — — MAC13” MAC16” MAC19” MAC21” 960 × 720 960 × 720 960 × 720 954 × 720 1280 × 720 1280 × 720 1280 × 720 1280 × 720 1280
Notices Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■ Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
■ Don’t place the projector where the cord can be walked on. This may result in fraying or damage to the plug. ■ Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners. ■ This product includes a lamp component that contains mercury. Please consult your state and local regulations regarding proper disposal or recycling, and do not place in the trash.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Declaration of Conformity According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: EPSON AMERICA, INC. 3840 Kilroy Airport Way MS 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
repair or replace on an exchange basis the defective unit, without charge for parts or labor. When warranty service involves the exchange of the product or of a part, the item replaced becomes EPSON property. The exchanged product or part may be new or previously repaired to the EPSON standard of quality, or, at EPSON’s option, may be another model of like kind and quality.
Index A Accessories, 10, 61 Air filter cleaning and replacing, 51 ordering, 10 Anti-theft device, 8, 10 Aspect button, 9, 23, 59 Aspect ratio, selecting, 23, 66 to 67 B Background Color setting, 36 Batteries, changing, 50 Black level, 30 Blank button, 9, 22 Blurry picture, 60 Brightness setting, 29 specification, 63 C Cables, connecting, 15 to 17 Child lock, 25 Cinema Color Editor setting up, 39 to 41 using, 42 to 48 Cleaning air filter, 51 lens and projector case, 49 Color adjusting, 31, 44 to 45 problem
H M Help, 61 Home Service, 7 Macintosh desktop adapter, 10 Memory button, 9, 33 Memory settings creating, 33, 46 deleting, 34, 48 renaming, 48 using, 33, 47 Menu button, 9, 27 Menus available settings, 28 to 37 customizing, 28 using, 27 Message setting, 36 Moving projector, 54 I Image adjusting, 17 to 19, 29 to 32, 44 to 45 changing aspect ratio, 23, 66 to 67 positioning, 19, 35 resizing, 23, 35 selecting source, 22 upside-down or backwards, 18 Image problems, 57 to 60 Info menu, 56 Input Signal setting
Projector checking status, 56 cleaning, 49 control panel, 9 dimensions, 64 feet, 19 lights, 55 to 56 locking, 8, 10, 25 menus, 28 to 37 parts, 8 positioning, 13 to 14 resetting menu options, 34 storing, 54 transporting, 54 turning on and off, 21 to 22, 57 Source buttons, 9 Source, selecting image, 22 Specifications compatible video formats, 65 electrical, 64 environmental, 64 general, 63 lamp, 63 remote control, 63 Squeeze mode, 23 Startup screen, selecting, 36 Static, 59 Storing projector, 54 Support, see
Z Zoom adjustment, 17 Zoom Caption setting, 23, 35 Zoom setting, 23 78
