PowerLite® Home Cinema 2000/2030 User's Guide Downloaded From projector-manual.
Downloaded From projector-manual.
Contents PowerLite Home Cinema 2000/2030 User's Guide.................................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents..............................................................
Connecting to External Speakers .................................................................................................. Connecting to External USB Devices ............................................................................................ USB Device Projection.............................................................................................................. Connecting a USB Device or Camera to the Projector..............................................................
Changing the Projection Mode Using the Menus........................................................................... Image Aspect Ratio ............................................................................................................................ Changing the Image Aspect Ratio ................................................................................................. Available Image Aspect Ratios ........................................................................................
Cleaning the 3D Glasses ............................................................................................................... 93 Cleaning the Projector Case.......................................................................................................... 93 Air Filter and Vent Maintenance .................................................................................................... 94 Cleaning the Air Filter and Vents...................................................................
Remote Control Specifications ......................................................................................................... Projector Dimension Specifications.................................................................................................. Projector Electrical Specifications .................................................................................................... Projector Environmental Specifications....................................................................
Downloaded From projector-manual.
PowerLite Home Cinema 2000/2030 User's Guide Welcome to the PowerLite Home Cinema 2000/2030 User's Guide. 9 Downloaded From projector-manual.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Easy-to-use setup and operation features • Real-time, automatic vertical keystone correction and horizontal keystone correction slider for flexible projector placement • Epson's Instant Off and Direct Power On features for quick setup and shut down • 1.
5 Projector documentation CD Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You can purchase one from Epson or an authorized Epson reseller. • To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller.
Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).
In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for details. Register your product online using the projector CD or at this site: epson.com/webreg Registering also lets you receive special updates on new accessories, products, and services.
Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Control panel 2 Horizontal keystone slider 3 Zoom ring 4 Focus ring 5 Kensington security lock slot 6 Air filter cover 7 Air filter intake 8 Remote receiver 9 Lens 10 Front adjustable foot 11 Foot adjust lever 15 Downloaded From projector-manual.
12 A/V Mute slide (lens cover) 13 Exhaust vent 14 A/V Mute slide lever 15 Lamp cover Parent topic: Projector Part Locations Related references Projector Light Status Related tasks Installing a Security Cable Projector Parts - Rear 1 HDMI 1 / MHL port 2 HDMI 2 port 3 PC port (VGA) 4 Video port 16 Downloaded From projector-manual.
5 Audio Out port 6 Service port 7 USB Type A port 8 Audio ports 9 RS-232C port 10 Remote receiver 11 AC input port Parent topic: Projector Part Locations Projector Parts - Base 1 Front adjustable foot 2 Rear feet 3 Security cable attachment point 17 Downloaded From projector-manual.
4 Mounting bracket holes Parent topic: Projector Part Locations Projector Parts - Control Panel 1 Power button/light 2 Source button (cycles through the list of sources) 3 Menu button (accesses projector menu system) 4 Enter button (selects options) 5 Esc button (cancels/exits functions) 6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Volume control buttons, horizontal keystone adjustment buttons (adjusts screen shape), and arrow buttons 8 Temp light 9 L
Projector Parts - Remote Control 1 Power button 2 Source buttons 3 HDMI Link button (displays the settings menu for HDMI Link), Link Menu button (displays the main menu of the connected device); and control buttons (control playback and other features of connected A/V devices that support the HDMI CEC standard) 19 Downloaded From projector-manual.
4 Menu button (accesses projector menu system) 5 Arrow buttons (move through on-screen options) 6 User button (customizable for different functions) 7 Color Mode button (selects display modes) 8 2D/3D button (cycles between 2D and 3D modes) 9 3D Format button (changes the 3D format) 10 Slideshow button (changes to the image source connected to the USB Type A port) 11 RGBCMY button (adjusts hue, saturation, and brightness for each RGBCMY color) 12 Mute button (turns off sound only) 13 Volu
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling 22 Downloaded From projector-manual.
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Feature Settings - Settings Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
16:9 Aspect Ratio Image or Screen Screen or image size Projection distance Wide to Tele 1 50 inches (126 cm) 53 to 64 inches (135 to 162 cm) 2 80 inches (203 cm) 85 to 103 inches (217 to 261 cm) 3 100 inches (254 cm) 107 to 129 inches (272 to 327 cm) 4 150 inches (381 cm) 161 to 194 inches (410 to 492 cm) 4:3 Aspect Ratio Image or Screen Screen or image size Projection distance Wide to Tele 1 50 inches (126 cm) 65 to 78 inches (165 to 199 cm) 2 80 inches (203 cm) 105 to 126 inches (266 to 320
Screen or image size Projection distance Wide to Tele 1 50 inches (126 cm) 57 to 69 inches (146 to 176 cm) 2 80 inches (203 cm) 93 to 111 inches (235 to 283 cm) 3 100 inches (254 cm) 116 to 139 inches (294 to 354 cm) 4 150 inches (381 cm) 175 to 210 inches (443 to 533 cm) Parent topic: Projector Placement Projector Connections You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound.
Connecting to External Speakers Connecting to External USB Devices Parent topic: Setting Up the Projector Related references Projector Setup Settings - Extended Menu Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
commands, set your game console's output format to a progressive signal of 480p or 720p. See your game console documentation for instructions. You can also select the Fast setting using the Fast/Fine button on the remote control to reduce lag time.
Parent topic: Connecting to Video Sources Related tasks Connecting to External Speakers Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1.
Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port. 2. Connect the other end to the projector's Video port.
2. Connect the other end of the cable to the projector's Audio port or ports. Note: To add additional sound, connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI connection provides the best image quality, if available). You can also connect speakers to any video source that has its own speaker connections.
3. Connect the other end to a PC port on the projector. 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Parent topic: Connecting to Computer Sources Related tasks Connecting to External Speakers Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it using the projector's HDMI port, you can still play sound through the projector's speaker system. Connect an optional stereo mini-jack adapter cable (with one 3.5 mm mini-plug and two RCA plugs). 1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port.
4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Parent topic: Projector Connections Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
• Formatted in FAT or FAT32 • Self-powered by their own AC power supplies (bus-powered hard drives are not recommended) • Avoid using hard drives with multiple partitions You can project slide shows from image files on a connected USB device or memory card reader.
2. Press the Slideshow button on the remote control. 3. Press the button again to cycle through other USB sources, if available. Parent topic: Connecting to External USB Devices Disconnecting a USB Device or Camera From the Projector When you finish presenting with a connected USB device or camera, you must prepare to disconnect the device from the projector. 1. If the device has a power button, turn off and unplug the device. 2. Disconnect the USB device or camera from the projector.
2. Insert the batteries with the + and – ends facing as shown. 3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Setting Up the Projector Related references Remote Control Specifications 36 Downloaded From projector-manual.
Opening the Lens Cover 1. To open the projector's lens cover, slide the A/V Mute slide lever until it clicks into the open position. 2. To cover the lens or temporarily turn off the projected picture and sound, slide the A/V Mute slide cover closed. Note: The lamp remains on in ECO mode while the lens cover is closed. Parent topic: Setting Up the Projector 37 Downloaded From projector-manual.
Wireless Network Projection You can send images to your projector through a wireless network. To do this, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection. Note: The wireless LAN module is not included with your projector. You can connect the projector to your wireless network by configuring the connection manually using the projector's Network menus.
The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network. Parent topic: Wireless Network Projection Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 39 Downloaded From projector-manual.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the Projector Name setting and enter a name up to 16 alphanumeric characters long to identify the projector over the network. Note: Use the displayed keyboard to enter the name. Press the arrow buttons on the remote control to highlight characters and press Enter to select them. 40 Downloaded From projector-manual.
7. Select the Wireless LAN menu and press Enter. 8. Select the settings on the Wireless LAN menu as necessary for your network. Note: Some items may be unavailable if Quick or Advanced connection mode is selected. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. After you complete the wireless settings for your projector, you need to select the wireless network on your computer.
Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you quickly connect to one computer, smartphone, or tablet Advanced: lets you connect a wireless network access point Channel 1ch In Quick connection mode, selects the frequency band (channel) used by the wireless LAN 6ch 11ch SSID Up to 32 alphanumeric characters (no spaces) Sets the SSID (network name) of the wireless LAN system the projector is connecting to Search Access Point —
Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1. To access your wireless utility software, double-click the network icon on the Windows taskbar. 2. Do one of the following: • If your projector is set up on an existing network (Advanced mode), select the network name (SSID). • If your projector is configured for Quick mode, select the projector's SSID. 3. Click Connect.
4. Select the Security menu and press Enter. 5. Select the security settings as necessary to match your network settings. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Open the projector's lens cover. 2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. The projector's power light turns blue. This indicates that the projector is receiving power. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the remote control to turn on the projector. 46 Downloaded From projector-manual.
The projector beeps and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children. If you do not see a projected image right away, try the following: • Verify the lens cover is open all the way. • Turn on the connected computer or video device.
2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). Caution: Do not turn the projector on immediately after turning it off. Turning the projector on and off frequently may shorten the life of the lamp. 3.
Parent topic: Using Basic Projector Features Viewing 3D Images You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses (not included with your projector). You can purchase Epson RF 3D glasses from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales). 1.
6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses will enter standby mode and the indicator light will flash green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing.
5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off. Parent topic: Viewing 3D Images Charging the 3D Glasses Charge the glasses when the status light on the glasses flashes red to indicate a low battery. 1.
The glasses are fully charged when the status light on the glasses stays green. Parent topic: Viewing 3D Images 3D Viewing Range When you view 3D images, make sure you are positioned within the viewing range shown here. 1 32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Related concepts Image Shape Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Adjust the slider until the image is evenly rectangular. After correction, your image is slightly smaller.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen. 3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus.
Resizing the Image With the Zoom Ring 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image.
2. To sharpen the image focus, rotate the projector’s focus ring. Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here. 58 Downloaded From projector-manual.
1 19.7 feet (6 m) 2 ± 15° 1 19.7 feet (6 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
2. For video image sources, insert a DVD or other video media and press its play button (if necessary). 3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
• Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen. • Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind a translucent screen.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Note: The Auto aspect ratio setting is available only for HDMI image sources.
3. Press the Color Mode button on the remote control to change the Color Mode. A list of available Color Modes appears. 4. To cycle through all the available Color Modes for your input signal, press the up or down arrow buttons repeatedly. Press Enter to select a Color Mode.
Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button. 3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment.
1. Turn on the projector and start a presentation that includes audio. 2. To lower or raise the volume, press the Volume buttons on the remote control or these buttons on the control panel. A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, use the projector menus.
Note: For best results, place your files on media that is formatted in FAT16/32. File contents File type (extension) Details Image .
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional images in a folder, highlight Next page or Previous page and press Enter. 3.
Related tasks Connecting a USB Device or Camera to the Projector Disconnecting a USB Device or Camera From the Projector Slideshow Display Options You can select these display options when using the projector's Slideshow feature.
Setting Options Description Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variety of effects Parent topic: Starting a Slide Show 70 Downloaded From projector-manual.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Projector Security Features Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1.
Locking the Projector's Buttons Installing a Security Cable Parent topic: Adjusting Projector Features Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Lock Setting setting and press Enter. 4.
Related references Projector Feature Settings - Settings Menu Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them. Parent topic: Locking the Projector's Buttons Related references Projector Feature Settings - Settings Menu Installing a Security Cable You can install two types of security cables on the projector to deter theft.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
7. When you finish changing settings on a menu, press Esc. 8. Press Menu or Esc to exit the menus. Parent topic: Adjusting the Menu Settings Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Tint Varying levels available Adjusts the balance of green to magenta tones in the image Sharpness Varying levels available Adjusts the sharpness or softness of image details Color Temp.
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source. 78 Downloaded From projector-manual.
Setting Options Description 3D Setup 3D Display Selects various 3D options 3D Format 3D Display: enables 3D mode 3D Depth 3D Format: selects the 3D format Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 3D Depth: sets the depth for the 3D image Diagonal Screen Size : Select the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: reverses the images projected for the left and right eyes (enable only i
Setting Options Description Position Up, down, left, right Adjusts the image location on the screen Auto Setup On Automatically optimizes computer image quality (when On) Off Noise Reduction Off Reduces flickering in analog images in three levels 1 2 3 Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 2% 4% 6% 8% 80 Downloaded From projector-manual.
Setting Options Description HDMI Video Range Auto Sets the video range to match the setting of the device connected to the HDMI input port Normal Expanded Auto: detects the video range automatically Normal: normally for images from a device other than a computer; can also be selected if the black areas of the image are too bright Expanded: normally for images from a computer; can also be selected if the image is too dark Note: Can only be set when Epson Super White (located in the Advanced setting un
Setting Options Description Keystone H/V-Keystone Adjusts image shape to rectangular (horizontally and vertically) Auto V-Keystone H-Keystone Adjuster H/V Keystone: lets you manually correct horizontal and vertical sides Auto V-Keystone: enables or disables automatic vertical keystone adjustment H-Keystone Adjuster: enables or disables manual horizontal keystone adjustment using the slider on the projector Volume Varying levels available 82 Downloaded From projector-manual.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options; allows the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Audio Out Device Power On Link Power Off Link Device Connections: lists the devices connected to the HDMI 1 and HDMI 2 ports HDMI Link: enables or disables the HDMI Link function Audio Out Device: selects whether to output audio from the internal speakers or a connected audio/video system Power On Link:controls th
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear/Ceiling User Button 3D Format 3D Depth Assigns a menu option to the User button on the remote control for one-touch access 3D Brightness Inverse 3D Glasses Power Consumption Info Parent topic: Adjusting the Menu Settings Related references Projector Setup and Installation Options Related tasks Correcting Image Shape with the Horizontal Keystone Slide
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Illumination High Altitude Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode: automatically turns off the projector after an interval of inactivity Illumination: turns off the lights on the projector High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) 85 Downloaded From projector-manual.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up Input Signal Video Signal PC Signal Video Signal: Specifies the signal type from input sources connected to the Video port or select Auto to detect
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Wireless LAN system Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Network Configuration Accesses additional network menus Parent topic: Adjusting the Menu Settings 87 Downloaded From projector-manual.
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. The information displayed depends on the currently selected input source. Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Information item Description Deep Color Displays Deep Color information Video Signal Displays the video signal format of the current input source Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Version Displays the firmware version of the projector Event ID Displays the application error log Event ID Code List Parent topic: Adjusting the Menu Settings Related references Optional Equipment and R
Event ID code Cause and solution 0484 Communication with computer was disconnected. Restart the EasyMP Network Projection program. 0483 The EasyMP Network Projection program quit unexpectedly. Check the network communication status, then turn the projector off and then on again. 04FE 0479 A projector system error has occurred. Turn the projector off and then on again. 04FF 0891 Cannot find an access point with the same SSID. Set your computer, access point, and projector to the same SSID.
You cannot reset the following settings using the Reset All option: • PC Signal • Language • Lamp Hours • All settings in the Network menu Parent topic: Adjusting the Menu Settings 91 Downloaded From projector-manual.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector. Caution: Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a flammable residue. Parent topic: Projector Maintenance Air Filter and Vent Maintenance Regular filter maintenance is important to maintaining your projector.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Caution: Do not use canned air. The gases may leave a flammable residue or push dust and debris into the projector's optics or other sensitive areas. 3. If dust is difficult to remove or the air filter is damaged, replace the air filter.
2. Carefully open the air filter cover. 3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations. 96 Downloaded From projector-manual.
4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 99 Downloaded From projector-manual.
6. Grasp the raised section of the lamp and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 100 Downloaded From projector-manual.
8. Push in the lamp firmly and tighten the screws to secure it. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. 101 Downloaded From projector-manual.
Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Specifications Transporting the Projector The projector contains precision parts, some of which are glass.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
1 Power light 2 Status light 3 Lamp light 4 Temp (temperature) light Power light Status light Lamp light Temp light Status and solution Blue Blue Off Off Normal operation. Blue Flashing blue Off Off Warming up. Wait for an image to appear. Blue Off Off Off Standby or sleep mode. Blue Flashing blue Off Off Shutting down. (When the Status light stops flashing, you can unplug the projector.) 106 Downloaded From projector-manual.
Power light Status light Lamp light Temp light Status and solution Blue Varies Off Flashing orange Projector is too hot. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter. • Make sure the environmental temperature is not too hot. Off Flashing blue Off Orange Projector has overheated and turned off. Leave it turned off to cool down.
Power light Status light Lamp light Temp light Status and solution Flashing blue Varies Flashing orange Off Replace the lamp soon to avoid damage. Do not continue using the projector. Off Flashing blue Off Flashing orange A fan or sensor has a problem. Turn the projector off, unplug it, and contact Epson for help. Off Flashing blue Flashing orange Flashing orange Auto Iris error. Turn the projector off, unplug it, and contact Epson for help.
Solutions When the Image is Not Rectangular Solutions When the Image Contains Noise or Static Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect Solutions When a 3D Image Does Not Display Correctly Solutions to Sound Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens cover is open all the way or off.
Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press the Source button on the projector repeatedly to cycle through the available sources. Wait a few seconds for an image to appear. • Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary. • Check the connection from the projector to your video sources.
2. Select the Display or Color LCD option, if necessary. 3. Click the Arrange or Arrangement tab. 4. Select the Mirror Displays checkbox. Parent topic: Solutions When "No Signal" Message Appears Solutions When "Not Supported" Message Appears If the "Not Supported" message appears, try the following solutions: • Make sure the correct input signal is selected on the Extended menu. • Make sure the computer's display resolution does not exceed the projector's resolution and frequency limit.
• If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape. • Turn on automatic keystone adjustments using the projector's menus. • Adjust the position of the projector's horizontal keystone slider.
Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen. • Position the projector so the keystone adjustment angle is not so wide that it distorts the image.
• Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables. • If you are using the ECO Power Consumption setting, try selecting Normal in the projector's menus. Note: At high altitudes or locations subject to high temperatures, the image may become darker and you may not be able to adjust the Power Consumption setting. • Position the projector close enough to the screen.
• Avoid using the projector near wireless networks, microwave ovens, 2.4 GHz cordless phones, or other devices that use the 2.4 GHz frequency band. These devices can interfere with the signal between the projector and the 3D glasses. • If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the Signal menu. Return the setting to its original value if changing it does not solve the problem.
Related concepts Projector Connections Related tasks Controlling the Volume with the Volume Buttons Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries. • Make sure you are operating the remote control within the reception angle and range of the projector. • Make sure the projector is not warming up or shutting down.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada). Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution 1920 × 1080 pixels Lens F=1.58 to 1.
PowerLite Home Cinema 2030: Normal Power Consumption mode: White light output: 2000 lumens (ISO 21118 standard) Color light output: 2000 lumens ECO Power Consumption mode: White light output: 1400 lumens (ISO 21118 standard) Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.
Keystone correction angle Vertical: ± 30° (manual or Auto Keystone) Horizontal: ± 30° (manual) USB Type Mini-B port compatibility USB 1.1 and 2.0 compliant for service and firmware updating USB Type A port compatibility One USB 1.1 and 2.
Width 11.69 inches (297 mm) Depth 9.72 inches (247 mm) Weight 6.2 lb (2.8 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% 2.9 to 1.3 A Power consumption Operating: (100 to 120 V) Normal Power Consumption mode: 300 W ECO Power Consumption mode: 224 W Standby: 0.28 W Power consumption Operating: (220 to 240 V) Normal Power Consumption mode: 287 W ECO Power Consumption mode: 217 W Standby: 0.
Operating altitude Up to 4921 feet (1500 m) Up to 9843 feet (3000 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) SXGA 60 1280 × 960 60 1280 × 1024 60 1600 × 900 TV (NTSC) 60 720 × 480 TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 576 TV (NTSC4.
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 HDMI 3D Signals Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV750p (720p) 50/60 1280 × 720 Frame Packing Side by Side Top and Bottom HDTV1125i (1080i) 50/60 1920 × 1080 Side by Side HDTV1125p (1080p) 50/60 1920 × 1080 Side by Side 24 1920
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 12° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
3D Safety Instructions Follow these 3D safety instructions when setting up and using the projector: • If you or any viewer experiences the following symptoms or other major discomfort from viewing 3D video images, immediately stop viewing and contact your health care provider: convulsions, eye or muscle twitching, loss of awareness, altered vision, involuntary movements, disorientation, eye strain, nausea/vomiting, dizziness, headaches, fatigue, or blurry/double vision that lasts longer than few seconds.
• People who are sleep deprived • People who are physically tired • People under the influence of drugs or alcohol • Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects • SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. • Do not use the device near any medical equipment or equipment that is automatically controlled, such as automatic doors or fire alarms.
medical equipment related to direct medical care, please make your own judgment on this product's suitability after a full evaluation. Parent topic: Important Safety Instructions FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Accolade® and PrivateLine® are registered trademarks; DuetTM and SizeWiseTM are trademarks; and Epson StoreSM and Extra CareSM are service marks of Epson America, Inc. Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
linux-2.6.27 patches udhcp 0.9.8 uvc rev.219 wireless_tools 29 EPSON original drivers Stonestreet One Drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (c) 1989, 1991 Free Software Foundation, Inc.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs").
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library.
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BSD License (Berkeley Software Distribution License) This projector product includes the open source software program "University of California, Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License". The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of BSD License programs busybox-1.13.
The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libjpeg programs libjpeg-6b License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows. Copyright (c) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software. For conditions of distribution and use, see the accompanying README file.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us. Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it.
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libpng programs libpng-1.2.49 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows. This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg" (88x31) and "pngnow.png" (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp@users.sourceforge.
jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code. If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types. "Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).
4. Redistribution.
8. Limitation of Liability.
The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of es-src-29-04-09 programs aes-src-29-04-09 License terms of conditions of each program which are provided by owner of the copyright to the "aessrc-29-04-09" are as follows. Copyright (c) 1998-2008, Brian Gladman, Worcester, UK. All rights reserved.
(1) Red Hat Incorporated Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W. Sandmann This file may be freely distributed as long as the author's name remains. (6) Eric Backus (C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software. (7) Sun Microsystems Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
(11) Christopher G. Demetriou Copyright (c) 2001 Christopher G. Demetriou All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
San Jose CA 95134 USA (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms. This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. (23) Intel (i960) Copyright (c) 1993 Intel Corporation Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.
DISCLAIMED.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Copyright (c) 2001 Daniel Eischen . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (36) - CodeSourcery, Inc. Copyright (c) 2009 CodeSourcery, Inc. All rights reserved.
* * * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * * Neither the name of MIPS Technologies Inc.
of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.). (3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.). (3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc., following conditions shall be satisfied. (a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. This information is subject to change without notice.
