PowerLite® Home Cinema 5025UB User's Guide
Contents PowerLite Home Cinema 5025UB User's Guide ....................................................................................... 7 Introduction to Your Projector ................................................................................................................... 8 Projector Features................................................................................................................................ 8 Product Box Contents.....................................................
Using Basic Projector Features ............................................................................................................... Turning On the Projector .................................................................................................................... Turning Off the Projector .................................................................................................................... Viewing 3D Images ..................................................................
Installing a Security Cable ............................................................................................................. 61 Saving Settings to Memory and Using Saved Settings ...................................................................... 61 Adjusting the Menu Settings .................................................................................................................... Using the Projector's Menus..........................................................................
Solutions When Only a Partial Image Appears ............................................................................ Solutions When the Image is Not Rectangular ............................................................................ Solutions When the Image Contains Noise or Static ................................................................... Solutions When the Image is Fuzzy or Blurry ..............................................................................
PowerLite Home Cinema 5025UB User's Guide Welcome to the PowerLite Home Cinema 5025UB User's Guide.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive a component video signal, you need a compatible component cable. You can purchase one from Epson or an authorized Epson reseller. • To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller.
Option or part Part number Belkin PureAV HDMI audio video cable, 3 ft AV22300-03 Belkin Pro Series VGA/SVGA cable, 6 ft F3H982-06 Belkin Pro Series VGA/SVGA cable, 10 ft F3H982-10 Belkin Pro Series VGA/SVGA cable, 25 ft F3H982-25 Kensington security lock ELPSL01 Remote control 1598522 In addition to the accessories listed above, 1-year and 2-year extended service plans are available.
Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • epson.com/support (U.S) or epson.ca/support (Canada) View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24 hours a day. • If you still need help after checking this manual and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Projector Parts - Front/Top 1 Lamp cover 2 Horizontal and vertical lens shift dials 3 Exhaust vent 4 Remote receiver 5 Lens shutter 6 Lens 7 Air intake/air filter cover 8 Front adjustable foot 9 Control panel and lights 10 Focus ring 11 Zoom ring Parent topic: Projector Part Locations 13
Projector Parts - Rear 1 Cable clip holes 2 HDMI1 port 3 HDMI2 port 4 Component ports 5 Video port 6 PC port (VGA) 7 RS-232C port 8 Trigger out port 9 Service port 10 Remote receiver 11 AC input port Parent topic: Projector Part Locations Related tasks Installing a Security Cable Attaching and Removing the Cable Clips 14
Projector Parts - Base 1 Front adjustable feet 2 Mounting bracket holes 3 Cable cover attachment point 4 Air exhaust vent Parent topic: Projector Part Locations 15
Projector Parts - Control Panel 1 Status light 2 Lamp light 3 Temp light 4 Menu button (accesses projector menu system) 5 Control panel cover 16
6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Arrow buttons 8 Esc button (cancels/exits functions) 9 Enter button (selects options) 10 Source button (cycles through the list of sources) 11 Power button/light Parent topic: Projector Part Locations Related references Projector Light Status 17
Projector Parts - Remote Control 1 On button (turns on projector) 2 P-in-P button (controls the Picture-in-Picture mode for HDMI inputs) 3 Source buttons (select specific video input sources) 18
4 HDMI Link button (displays the settings menu for HDMI Link) Link Menu button (displays the main menu of the connected device) Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) 5 2D/3D button (cycles between 2D and 3D modes) 6 Arrow buttons (move though on-screen options) 7 Default button (returns selected setting to default value) 8 Menu button (accesses projector menu system) 9 Auto Iris button (optimizes the image based on brightness
Projector Memory Options - Memory Menu 20
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Front Rear Front Ceiling 22
Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Feature Settings - Settings Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 40 inches (101.6 cm) 57 to 121.7 inches 11 inches (28 cm) 35.0 inches (89 cm) 16.5 inches (42 cm) 52.4 inches (133 cm) 22 inches (56 cm) 70.1 inches (178 cm) 27.6 inches (70 cm) 87.4 inches (222 cm) 33.1 inches (84 cm) 105.1 inches (267 cm) 41.3 inches (105 cm) 131.1 inches (333 cm) 54.7 inches (139 cm) 174.
Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 100 inches (254 cm) 117.3 to 250.4 inches 22.4 inches (57 cm) 71.3 inches (181 cm) 26.8 inches (68 cm) 85.8 inches (218 cm) 33.5 inches (85 cm) 107.1 inches (272 cm) 40.6 inches (103 cm) 128.7 inches (327 cm) (298 to 636 cm) 120 inches (304.8 cm) 141.3 to 300.8 inches (359 to 764 cm) 150 inches (381 cm) 177.2 to 376.4 inches (450 to 956 cm) 180 inches (457.2 cm) 212.
Related references Projector Setup Settings - Extended Menu Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector. Connecting to an HDMI Video Source Attaching and Removing the Cable Clips Connecting to a Component Video Source Connecting to a Composite Video Source Parent topic: Projector Connections Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signal Menu Related tasks Attaching and Removing the Cable Clips Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the HDMI cables. 1. Plug in the HDMI cables. 2. Insert each guide into the cable clip holes near the HDMI port. 3. Attach the cable clips to the HDMI cables. Be sure to leave the clamps unlocked. 4.
2. Connect the other end to the projector's color-coded Component video input ports. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Extended menu. Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher.
Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p, 720p, or higher. See your game console documentation for instructions. Parent topic: Connecting to Video Sources Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector.
Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. 1. Connect the HDMI cable to your computer's HDMI output port. 2. Connect the other end to one of the projector's HDMI ports.
1 Video source 2 Surround sound speakers 3 Receiver 4 Video cable Parent topic: Projector Connections Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 3. Press the power button on the projector or the On button on the remote control to turn on the projector. The shutter opens and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue.
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Note: When using the Blank feature, the projector lamp is still on. To turn off the lamp, turn off the projector. 1.
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status light is on or flashing. Parent topic: Using Basic Projector Features Related tasks Shutting Off the Picture Temporarily Transporting the Projector Viewing 3D Images You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses (not included with your projector).
5. Slide the power switch on the 3D glasses to the On position. 6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the status light flashes green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing.
4. Slide the power switch on the 3D glasses to the On position. 5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off. Parent topic: Viewing 3D Images Charging the 3D Glasses Charge the glasses when the status light on the glasses flashes red to indicate a low battery.
1. Connect the smaller end of the charging cable to the port on the bridge of the glasses. Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable. 2. Do one of the following: • Plug the other end of the charging cable into a powered USB port on a computer or other device. • Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications: Input: 100-240V, ~0.
1 32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
If the projected image is unevenly rectangular, you need to adjust the image shape. Adjusting the Image Position Using Lens Shift Parent topic: Using Basic Projector Features Related concepts Image Shape Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.
2. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary. Note: You cannot move the image to both the horizontal and vertical maximum values. 1 Horizontal width × 47% 2 Vertical height × 96% Follow these guidelines when using lens shift to adjust your images: • When adjusting the image height, position the image lower than where you want it to be and then move it up using the vertical lens shift dial.
Parent topic: Adjusting the Image Height Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image.
2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2. To sharpen the image focus, rotate the projector’s focus ring.
Parent topic: Using Basic Projector Features Adjusting the Color Convergence (Panel Alignment) You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image. Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature.
• B to adjust the blue color convergence. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted. 8. Select the Pattern Color setting and press Enter. 9. Select the pattern you want to use and press Enter. 10. Select Start Adjustments and press Enter. You see this screen: 11. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box. 12.
You see this screen: 14. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any box on the screen that is misaligned and press Enter to adjust the color convergence. Repeat this step as necessary.
Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here. 1 32 feet (10 m) 2 ± 30° 3 60° 4 10° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
1. Make sure the connected image source you want to use is turned on. 2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Related concepts Projector Placement Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.
Available Image Aspect Ratios You can select the following image aspect ratios, depending on the input signal from your image source. Note: When the projector is in 3D mode, the aspect ratio is automatically set to Normal. Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal.
Related references Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode.
Color Mode Description B&W Cinema Best for black and white movies projected in a dark room 3D Images Color Mode Description 3D Dynamic Best for projecting in a bright room 3D Cinema Best for movies projected in a dark room 3D THX Best for projecting in a dark room Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1.
4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Using Picture in Picture You can use Picture in Picture mode to view two image sources simultaneously. Note: You can display only HDMI video sources when Picture in Picture mode is active. 1.
Available Picture in Picture Options You can adjust the following options by pressing the Menu button on the remote control while Picture in Picture mode is active: Setting Description Subscreen Size Adjusts the size of the sub-screen Subscreen Position Adjusts the location where the sub-screen is displayed Swap Main/Sub Switches the video source displayed on the main screen with the source displayed on the sub-screen Exit Picture in Picture Closes the sub-screen and resumes normal projection Pare
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture Temporarily Projector Security Features Saving Settings to Memory and Using Saved Settings Shutting Off the Picture Temporarily You can temporarily turn off the projected picture if you want to redirect your audience's attention during a presentation. Any video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1.
1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Lock Setting setting and press Enter. 4. Select one of these lock types and press Enter: • To lock the projector's power button, select Child Lock. To turn the projector on, you must press the power button for longer than three seconds. • To lock all buttons except the power button, select Control Panel Lock. You see a confirmation prompt. 5. Select Yes and press Enter. 6.
Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. Parent topic: Projector Security Features Saving Settings to Memory and Using Saved Settings You can save customized settings for each of your video inputs and then select the saved settings whenever you want to use them. 1. Turn on the projector and display an image. 2. Press the Menu button.
Note: A memory name that has already been used is indicated by a green mark. Saving over a previously saved memory overwrites the settings with your current settings. • Erase Memory: Erases the selected memory settings • Rename Memory: Renames a saved memory 5. Press Esc to exit.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Note: The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Skin Tone Varying levels available Makes fine adjustments to the color tone; higher values tint the image blue and lower values tint the image red Advanced Gamma Selects various detailed color settings RGB RGBCMY EPSON Super White Gamma: adjusts the gamma levels of the image RGB: adjusts the offset and gain for each color RGBCMY: adjusts the hue, saturation, and brightness for each color EPSON Super White: reduces over-exposure of whites in your image; can be set only w
Parent topic: Adjusting the Menu Settings Related concepts Color Mode Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. Note: The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description 3D Setup 3D Display Selects various 3D options 2D-to-3D Conversion 3D Display: enables 3D mode 3D Format 2D-to-3D Conversion: converts 2D images to 3D 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 3D Format: selects the 3D format 3D Depth: sets the depth for the 3D image Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: revers
Setting Options Description Deinterlacing Off Sets whether to convert interlaced-to-progressive signals for certain video image types Video Film/Auto Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Motion Detection 1 to 5 Selects how the image is converted to a progressive signal (Adjust this setting if you experience problems with still image quality or flickering video.
Setting Options Description Advanced Noise Reduction Noise Reduction: reduces flickering in analog images in three levels Setup Level Overscan HDMI Video Range Image Processing Setup Level: adjusts the level at which dark areas of the image are rendered black; leave this setting at 0% for most video equipment; check your video equipment specifications to verify the correct setting Overscan: changes the projected image ratio to make the edges visible by a selectable percentage or automatically HDMI Vi
Parent topic: Adjusting the Menu Settings Related concepts Image Aspect Ratio Related tasks Viewing 3D Images Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Power On Link Power Off Link Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports HDMI Link: enables or disables the HDMI Link function Power On Link: controls what happens when you turn on the projector or a linked device • PJ -> Device or Bidirectional: turns on the linked device when
Setting Options Description User Button 2D-to-3D Conversion Assigns a menu option to the User button on the remote control for one-touch access 3D Depth 3D Brightness Inverse 3D Glasses Power Consumption Info Picture in Picture See the list of available Picture in Adjusts the size and location of Picture options the sub-screen, swaps sources and exits Picture in Picture mode Parent topic: Adjusting the Menu Settings Related concepts Projector Security Features Projector Placement Related references
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation.
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Illumination Trigger Out High Altitude Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode: automatically places the projector in standby mode after an interval of inactivity Illumination: turns off the lights on the projector Trigger Out: outputs a DC 12V signal from the 3.
Setting Options Description Display Menu Position Selects various display options Menu Color Menu Position: adjusts the location where the menu is displayed Messages Display Background Startup Screen Standby Confirmation Menu Color: selects the color of the menu Messages: controls whether messages are displayed on the screen Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether the Epson logo appears when the projector starts up
Setting Options Description Panel Alignment Panel Alignment Corrects color misalignment in the projected image Select Color Pattern Color Start Adjustments Panel Alignment: enables adjustments for color convergence (the alignment of the red and blue colors in the projected image) Select Color: specifies the color convergence to correct Pattern Color: specifies the color pattern used during panel alignment Start Adjustments: starts the Panel Alignment feature Language Various languages available Se
Projector Memory Options - Memory Menu Your projector comes with 10 memory locations where you can save customized settings to obtain the best picture quality for each of your video inputs.
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Note: The information displayed depends on the currently selected input source. Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Information item Description Deep Color Displays Deep Color information Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Version Displays the firmware version of the projector Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Related tasks Replacing the Lamp Resetting the Lamp Timer Projector Reset Options - Reset Menu You can reset most of the pr
You cannot reset the following settings using the Reset All option: • PC Signal • Language • Lamp Hours • Memory settings Parent topic: Adjusting the Menu Settings 81
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Note: Unplug any charging cables from the glasses before cleaning them. Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector.
Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties. Cleaning the Air Filter Replacing the Air Filter Parent topic: Projector Maintenance Related references Projector Light Status Cleaning the Air Filter You need to clean the projector's air filter in the following situations: • The filter or vents get dusty. • You see a message telling you to clean it. 1. Turn off the projector and unplug the power cord. 2.
3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter. 6. Place the air filter back in the projector as shown. 7. Attach the air filter cover and press gently until it clicks into place.
• If the filter is a dark gray color You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1. Turn off the projector and unplug the power cord. 2. Press in on the inner edge of the air filter cover to release the latch, then pull to remove. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Attach the air filter cover and press gently until it clicks into place. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down until it locks into place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage.
Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands.
3. Insert the batteries with the + and – ends facing as shown. 4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Remove any equipment connected to the projector. • Center the lens position using the vertical and horizontal lens shift dials. • When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image Problems Solving Projector or Remote Control Operation Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on. If this does not solve the problem, check the following: • The lights on the projector may indicate what the problem is.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp light Temp light Status and solution Blue Flashing blue Off Off Warming up; wait for an image to appear Off Off Off Off Standby or sleep mode Blue Flashing blue Off Off Shutting down; when the Status light stops flashing, you can unplug the projector Flashing blue Varies Off Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem Off • Check the Lamp Hours in the Info menu to see if the lamp is burned out.
Related references Projector Setup Settings - Extended Menu Related tasks Cleaning the Air Filter Replacing the Lamp Replacing the Air Filter Solving Image Problems Check the solutions in these sections if you have any problems with projected images.
• For images projected with Windows Media Center, reduce the screen size from full screen mode. • For images projected from applications using Windows DirectX, turn off DirectX functions.
4. If necessary, check your video card settings and set the multiple display option to Mirror or Duplicate. Parent topic: Solutions When "No Signal" Message Appears Displaying From a Mac Laptop If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) 1. Open the System Preferences utility and select Displays. 2. Click the Arrangement tab. 3. Select the Mirror Displays checkbox.
Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When the Image is Not Rectangular If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. • If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape.
• If you connected an extension power cable, try projecting without it to see if it caused interference in the signal. Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens.
• Check your video source settings. • Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Advanced, and Color Saturation. • Make sure you selected the correct PC Signal or Video Signal setting on the Extended menu, if available for your image source. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.
• Make sure your screen size matches the Diagonal Screen Size setting on the Signal menu. • Avoid using the projector near wireless networks, microwave ovens, 2.4 GHz cordless phones, or other devices that use the 2.4 GHz frequency band. These devices can interfere with the signal between the projector and the 3D glasses. • If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the Signal menu.
• If the projector's lamp shuts off, the Status light is flashing blue, and the Temp light is orange, the projector has overheated and shut off. Check the solutions for this light status. • If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receiver setting is turned on in the projector's menu, if available.
Remote Control Operation Projector Feature Settings - Settings Menu Related tasks Replacing the Remote Control Batteries Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to common problems with your projector.
Parent topic: Solving Problems 111
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution 1920 × 1080 pixels Lens F=2.3 to 3.
Image size 30 inches (0.76 m) to 300 inches (7.62 m) (in native aspect ratio) Projection distance 34 inches (0.87 m) to 754 inches (19.15 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:9 (width-to-height) Focus adjustment Manual Zoom adjustment Manual (optical) Zoom ratio 1-2.
Remote Control Specifications Reception range 32 feet (10 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 5.51 inches (140 mm) Width 18.35 inches (466 mm) Depth 15.55 inches (395 mm) Weight 18.4 lb (8.4 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% 3.7 to 1.
Projector Environmental Specifications Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity (relative, noncondensing) Operating: 20 to 80% Operating altitude Up to 4921 feet (1500 m) Storage: 10 to 90% Up to 7500 feet (2286 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 60 1366 × 768 60/75/85 1280 × 800 70/75/85 1152 × 864 60 1280 × 960 60 1280 × 1024 60 1600 × 900 TV (NTSC) 60 720 × 480 TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 576 TV (NTSC4.
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 HDMI 3D Signals Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV (720p) 50/60 1280 × 720 Frame Packing Side by Side Top and Bottom HDTV (1080i) 50/60 1920 × 1080 Side by Side HDTV (1080p) 50/60 1920 × 1080 Side by Side 24 1920 × 1080
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
3D Safety Instructions Follow these 3D safety instructions when setting up and using the projector: • If you or any viewer experiences the following symptoms or other major discomfort from viewing 3D video images, immediately stop viewing and contact your health care provider: convulsions, eye or muscle twitching, loss of awareness, altered vision, involuntary movements, disorientation, eye strain, nausea/vomiting, dizziness, headaches, fatigue, or blurry/double vision that lasts longer than few seconds.
• People who are sleep deprived • People who are physically tired • People under the influence of drugs or alcohol • Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects • SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. • Do not use the device near any medical equipment or equipment that is automatically controlled, such as automatic doors or fire alarms.
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices Open Source Software License GNU GPL This projector product includes the open source software programs which apply the GNU General Public License Version 2 or later version ("GPL Programs").
EPSON original drivers Stonestreet One Drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (c) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9.
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs"). We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library.
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BSD License (Berkeley Software Distribution License) This projector product includes the open source software program "University of California, Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License". The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of BSD License programs busybox-1.13.
The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libjpeg programs libjpeg-6b License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows. Copyright (c) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software. For conditions of distribution and use, see the accompanying README file.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us. Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it.
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libpng programs libpng-1.2.49 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows. This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg" (88x31) and "pngnow.png" (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp@users.sourceforge.
jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code. If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types. "Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).
4. Redistribution.
8. Limitation of Liability.
The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of es-src-29-04-09 programs newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib". The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of newlib programs newlib 1.17.
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. (4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc.
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (12) SuperH, Inc. Copyright 2002 SuperH, Inc.
THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Copyright (c) 1984,2000 S.L. Moshier Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE PRODUCT LICENSED HEREUNDER. (26) Mike Barcroft Copyright (c) 2001 Mike Barcroft All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(35) - ARM Ltd (arm and thumb variant targets only) Copyright (c) 2009 ARM Ltd All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED.
MIT License This projector product includes the open source software program which applies the terms and conditions provided by owner of the copyright to the "MIT License". The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of MIT License programs jquery-1.7.2.min.js jquery-ui-1.8.20.custom.zip jquery.ui.touch-punch.js jquery.upload-1.0.2.min.
License terms of conditions of each program which are provided by owner of the copyright to the "TOPPERS/JSP" are as follows. TOPPERS/JSP Kernel Toyohashi Open Platform for Embedded Real-Time Systems/ Just Standard Profile Kernel Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of Technology, JAPAN Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory Graduate School of Information Science, Nagoya Univ., JAPAN.
Note: The TOPPERS License has been revised several times; what is shown above is the latest version that is to be applied to software made public hereafter. TINET This projector product includes the open source software program "TINET" which applies the terms and conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of TINET programs tinet-1.4.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (6) TINET and TOPPERS TINET (TCP/IP Protocol Stack) Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of Technology, JAPAN TINET (TCP/IP Protocol Stack) Copyright (C) 2001-2006 by Dep.
other rights or licenses are granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works, trade secrets or other intellectual property rights of Stonestreet One, LLC®. © 2000-2012 Stonestreet One, LLC® All Rights Reserved. Parent topic: Notices Copyright Notice All rights reserved.
11/14 CPD-42014 Parent topic: Copyright Notice 171
