PowerLite® Home Cinema 5030UB/5030UBe User's Guide
Contents PowerLite Home Cinema 5030UB/5030UBe User's Guide ....................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents.....................................................................
Installing Batteries in the Remote Control .......................................................................................... 33 Using Basic Projector Features ............................................................................................................... Turning On the Projector .................................................................................................................... Turning Off the Projector ................................................................
Unlocking the Projector's Buttons ............................................................................................. 65 Installing a Security Cable ............................................................................................................. 65 Saving Settings to Memory and Using Saved Settings ...................................................................... 65 Using WirelessHD ..................................................................................................
Solving Problems .................................................................................................................................... 107 Projection Problem Tips ................................................................................................................... 107 Projector Light Status ....................................................................................................................... 107 Solving Image Problems ............................................
3D Safety Instructions ................................................................................................................. Restriction of Use ........................................................................................................................ FCC Compliance Statement............................................................................................................. Trademarks ..........................................................................................
PowerLite Home Cinema 5030UB/5030UBe User's Guide Welcome to the PowerLite Home Cinema 5030UB/5030UBe User's Guide.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• 2.1× optical zoom ratio for improved zooming capability Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
5 Projector documentation CD 6 3D glasses (2 pairs) 7 WirelessHD Transmitter (PowerLite Home Cinema 5030UBe) 8 WirelessHD Transmitter AC adapter (PowerLite Home Cinema 5030UBe) Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive a component video signal, you need a compatible component cable. You can purchase one from Epson or an authorized Epson reseller.
Epson offers the following optional accessories and replacement parts for your projector: Option or part Part number Genuine Epson replacement lamp (ELPLP69) V13H010L69 Replacement air filter V13H134A39 RF 3D glasses (ELPGS03) V12H548006 Projector ceiling mount CHF1000 Belkin PureAV HDMI audio video cable, 6 ft AV22300-06 Belkin PureAV HDMI audio video cable, 12 ft AV22300-12 Belkin PureAV HDMI audio video cable, 3 ft AV22300-03 Belkin Pro Series VGA/SVGA cable, 6 ft F3H982-06 Belkin Pro S
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • epson.
Projector Parts - Front/Top 1 Lamp cover 2 Horizontal and vertical lens shift dials 3 Exhaust vent 4 Remote receiver 5 Lens shutter 6 Lens 7 Air intake/air filter cover 8 Front adjustable foot 9 Control panel and lights 10 Focus ring 11 Zoom ring Parent topic: Projector Part Locations 15
Projector Parts - Rear 1 Cable clip holes 2 HDMI1 port 3 HDMI2 port 4 Component ports 5 Video port 6 PC port (VGA) 7 RS-232C port 8 Trigger out port 9 Service port 10 Remote receiver 11 AC input port Parent topic: Projector Part Locations Related tasks Installing a Security Cable Attaching and Removing the Cable Clips 16
Projector Parts - Base 1 Front adjustable feet 2 Mounting bracket holes 3 Cable cover attachment point 4 Air exhaust vent Caution: The air exhaust vent cools the WirelessHD receiver. If you mount the projector on the ceiling, make sure dust does not block the vent or the WirelessHD receiver can overheat.
Projector Parts - Control Panel 1 Status light 2 Lamp light 3 Temp light 4 Menu button (accesses projector menu system) 5 Control panel cover 18
6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Arrow buttons 8 Esc button (cancels/exits functions) 9 Enter button (selects options) 10 Source button (cycles through the list of sources) 11 Power button/light Parent topic: Projector Part Locations Related references Projector Light Status 19
Projector Parts - Remote Control 1 On button (turns on projector) 2 P-in-P button (controls the Picture-in-Picture mode for HDMI inputs) 3 Source buttons (select specific video input sources) 20
4 HDMI Link button (displays the settings menu for HDMI Link) Link Menu button (displays the main menu of the connected device) Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) 5 2D/3D button (cycles between 2D and 3D modes) 6 Arrow buttons (move though on-screen options) 7 Default button (returns selected setting to default value) 8 Menu button (accesses projector menu system) 9 Auto Iris button (optimizes the image based on brightness
Projector Memory Options - Memory Menu 22
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling 24
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Feature Settings - Settings Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 40 inches (101.6 cm) 57 to 121.7 inches 11 inches (28 cm) 35.0 inches (89 cm) 16.5 inches (42 cm) 52.4 inches (133 cm) 22 inches (56 cm) 70.1 inches (178 cm) 27.6 inches (70 cm) 87.4 inches (222 cm) 33.1 inches (84 cm) 105.1 inches (267 cm) 41.3 inches (105 cm) 131.1 inches (333 cm) 54.7 inches (139 cm) 174.8 inches (444 cm) (144 to 309 cm) 60 inches (152.4 cm) 85.8 to 183.
Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 100 inches (254 cm) 117.3 to 250.4 inches 22.4 inches (57 cm) 71.3 inches (181 cm) 26.8 inches (68 cm) 85.8 inches (218 cm) 33.5 inches (85 cm) 107.1 inches (272 cm) 40.6 inches (103 cm) 128.7 inches (327 cm) (298 to 636 cm) 120 inches (304.8 cm) 141.3 to 300.8 inches (359 to 764 cm) 150 inches (381 cm) 177.2 to 376.4 inches (450 to 956 cm) 180 inches (457.2 cm) 212.
Related references Projector Setup Settings - Extended Menu Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
Note: When an audio/video source that meets the HDMI CEC standard is connected to the projector's HDMI port, you can use the projector's remote control to control certain features of the linked device by pressing the HDMI Link button on the remote control and setting HDMI Link to On.
1. Connect the MHL cable or adapter to your device's Micro-USB port. 2. If you are using an MHL adapter, connect it to an MHL-compatible HDMI cable. 3. Connect the other end of the cable to the WirelessHD Transmitter's HDMI 5 / MHL (IN) port. Parent topic: Connecting to Video Sources Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component video cable.
You can also select the Fast Image Processing setting to reduce lag time. Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signal Menu Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port. 2. Connect the other end to the projector's Video port.
2. Connect the VGA computer cable to your computer's monitor port. 3. Connect the other end to a PC port on the projector. 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Connecting to a Computer for HDMI Video If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
1 Video source 2 Surround sound 3 Receiver 4 Video cable Parent topic: Projector Connections Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
1. Open the battery cover. 2. Insert the batteries with the + and – ends facing as shown.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 3. Press the power button on the projector or the On button on the remote control to turn on the projector. The shutter opens and the Status light flashes blue as the projector warms up. Once the projector is warmed up, the Status light stops flashing and turns blue.
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Note: When using the Blank feature, the projector lamp is still on. To turn off the lamp, turn off the projector. 1.
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status light is on or flashing. Parent topic: Using Basic Projector Features Related tasks Shutting Off the Picture Temporarily Transporting the Projector Viewing 3D Images You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses. You can purchase Epson RF 3D glasses from an Epson authorized reseller.
5. Slide the power switch on the 3D glasses to the On position. 6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the indicator light flashes green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing.
4. Slide the power switch on the 3D glasses to the On position. 5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off. Parent topic: Viewing 3D Images Charging the 3D Glasses Charge the glasses when the status light on the glasses flashes red to indicate a low battery.
1. Connect the smaller end of the charging cable to the port on the bridge of the glasses. Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable. 2. Do one of the following: • Plug the other end of the charging cable into a powered USB port on a computer or other device. • Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications: Input: 100-240V, ~0.
1 32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
If the projected image is unevenly rectangular, you need to adjust the image shape. Adjusting the Image Position Using Lens Shift Parent topic: Using Basic Projector Features Related concepts Image Shape Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.
1 Horizontal height × 47% 2 Vertical height × 96% Follow these guidelines when using lens shift to adjust your images: • When adjusting the image height, position the image lower than where you want it to be and then move it up using the vertical lens shift dial. This will help prevent the image from moving down after adjustment. • Keeping the vertical and horizontal lens shift dials in their center positions produces the clearest picture.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Resizing the Image With the Zoom Ring 1. Turn on the projector and display an image.
2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2. To sharpen the image focus, rotate the projector’s focus ring.
Parent topic: Using Basic Projector Features Adjusting the Color Convergence (Panel Alignment) You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image. Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature.
• B to adjust the blue color convergence. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted. 8. Select the Pattern Color setting and press Enter. 9. Select the pattern you want to use and press Enter. 10. Select Start Adjustments and press Enter. You see this screen: 11. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box. 12.
14. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any box on the screen that is misaligned and press Enter to adjust the color convergence. Repeat this step as necessary.
Vertical 1 32 feet (10 m) 2 ± 30° 3 60° 4 10° 53
Horizontal 1 32 feet (10 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries. Parent topic: Using Basic Projector Features Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1.
2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
• Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen. • Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind a translucent screen.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image.
Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode. A list of available Color Modes appears. 4.
Color Mode Description 3D Dynamic Best for projecting in a bright room 3D Cinema Best for movies projected in a dark room 3D THX Best for projecting in a dark room Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button.
• Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Using Picture in Picture You can use the Picture in Picture mode to view two image sources simultaneously. Note: You can only display HDMI or WirelessHD video sources when Picture in Picture mode is active. 1. Turn on the projector and switch to the HDMI or WirelessHD image source you want to use. 2.
Setting Description Subscreen Size Adjusts the size of the sub-screen Subscreen Position Adjusts the location where the sub-screen is displayed Subscreen Source Selects which source appears in the sub-screen (PowerLite Home Cinema 5030UBe) Swap Main/Sub Switches the video source displayed on the main screen with the source displayed on the sub-screen Exit Picture in Picture Closes the sub-screen and resumes normal projection Parent topic: Using Picture in Picture 62
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture Temporarily Projector Security Features Saving Settings to Memory and Using Saved Settings Shutting Off the Picture Temporarily You can temporarily turn off the projected picture if you want to redirect your audience's attention during a presentation. Any video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1.
Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Lock Setting setting and press Enter. 4. Select one of these lock types and press Enter: • To lock the projector's power button, select Child Lock.
Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them. Parent topic: Locking the Projector's Buttons Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson.
5. Select one of the following options: • Load Memory: Overwrites your current settings with saved settings • Save Memory: Saves your current settings to memory (10 memories with different names are available) Note: A memory name that is being used is indicated by a green mark. Saving over a previously saved memory overwrites the settings with your current settings.
Using WirelessHD You can use the included WirelessHD transmitter to wirelessly stream HD content from a video device to the projector (PowerLite Home Cinema 5030UBe).
2. Connect HDMI cables to your video devices and to the HDMI input ports on the side and back of the WirelessHD transmitter. Note: You can connect an MHL-compatible smartphone or tablet to the HDMI 5 / MHL (IN) port on the WirelessHD Transmitter. 3. To use the WirelessHD transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and to the HDMI output port on the back of the transmitter.
3. Press the WirelessHD button on the remote control. The WiHD light on the transmitter lights up and your projector displays WirelessHD content. Note: If the WirelessHD connection fails, press the Setup button on the bottom of the WirelessHD transmitter and try again. Parent topic: Using WirelessHD Switching WirelessHD Sources If you have connected multiple HDMI input sources to your WirelessHD transmitter, you can use the projector remote control to switch between sources. 1.
2. Press the Input button repeatedly to highlight different input sources. 3. When you have highlighted the source you want to switch to, release the Input button. The display automatically switches to the highlighted source after a few seconds.
• Press and hold the P-in-P button on the remote control to switch the sources shown in the main display and the sub-screen. 3. When you are finished watching Picture-in-Picture, press the P-in-P button on the remote control to resume normal projection.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Skin Tone Varying levels available Makes fine adjustments to the color tone; higher values tint the image blue and lower values tint the image red Advanced Gamma Selects various detailed color settings RGB RGBCMY EPSON Super White Gamma: adjusts the gamma levels of the image RGB: adjusts the offset and gain for each color RGBCMY: adjusts the hue, saturation, and brightness for each color EPSON Super White: reduces over-exposure of whites in your image; can be set only w
Parent topic: Adjusting the Menu Settings Related concepts Color Mode Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description 3D Setup 3D Display Selects various 3D options 2D-to-3D Conversion 3D Display: enables 3D mode 3D Format 2D-to-3D Conversion: converts 2D images to 3D 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 3D Format: selects the 3D format 3D Depth: sets the depth for the 3D image Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: revers
Setting Options Description Deinterlacing Off Sets whether to convert interlaced-to-progressive signals for certain video image types Video Film/Auto Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Motion Detection 1 to 5 Selects how the image is converted to a progressive signal (Adjust this setting if you experience problems with still image quality or flickering video.
Setting Options Description Advanced Noise Reduction Noise Reduction: reduces flickering in analog images in three levels Setup Level Overscan HDMI Video Range Image Processing Setup Level: adjusts the level at which dark areas of the image are rendered black; leave this setting at 0% for most video equipment; check your video equipment specifications to verify the correct setting Overscan: changes the projected image ratio to make the edges visible by a selectable percentage or automatically HDMI Vi
Parent topic: Adjusting the Menu Settings Related concepts Image Aspect Ratio Related tasks Viewing 3D Images Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Power On Link Power Off Link Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports HDMI Link: enables or disables the HDMI Link function Power On Link: controls what happens when you turn on the projector or a linked device • PJ -> Device or Bidirectional: turns on the linked device when
Setting Options Description WirelessHD Device Connections (PowerLite Home Cinema 5030UBe) WirelessHD Device Connections: displays a list of available WirelessHD devices Reception WiHD Mode WirelessHD: controls whether the projector receives WirelessHD signals Reception: displays the strength of the WirelessHD signal WiHD Mode: adjusts the WirelessHD signal strength and range • Normal: use this default setting in most situations • Full: uses the maximum video bandwidth at all times • Dynamic: provid
Setting Options Description User Button 2D-to-3D Conversion Assigns a menu option to the User button on the remote control for one-touch access 3D Depth 3D Brightness Inverse 3D Glasses Power Consumption Info Picture in Picture See the list of available Picture in Adjusts the size and location of Picture options the sub-screen, swaps sources and exits Picture in Picture mode Parent topic: Adjusting the Menu Settings Related concepts Projector Security Features Projector Placement Related references
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Illumination Trigger Out High Altitude Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode: automatically turns off the projector after an interval of inactivity Illumination: turns off the lights on the projector Trigger Out: outputs a DC 12V signal from the 3.
Setting Options Description Display Menu Position Selects various display options Menu Color Menu Position: adjusts the location where the menu is displayed Messages Display Background Startup Screen Standby Confirmation Menu Color: selects the color of the menu Messages: controls whether messages are displayed on the screen Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts u
Setting Options Description Panel Alignment Panel Alignment Corrects color misalignment in the projected image Select Color Pattern Color Start Adjustments Panel Alignment: enables adjustments for color convergence (the alignment of the red and blue colors in the projected image) Select Color: specifies the color convergence to correct Pattern Color: specifies the color pattern used during panel alignment Start Adjustments: starts the Panel Alignment feature Language Various languages available Se
Setting Description Load Memory Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to load it Save Memory Saves the current projector settings to the projector's memory Erase Memory Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to erase it Rename Memory Displays the list of customized settings entries that you have created; select an entry and pr
Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Information item Description Version Displays the firmware version of the projector Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Related tasks Replacing the Lamp Resetting the Lamp Timer Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All option on the Reset menu.
Parent topic: Adjusting the Menu Settings 90
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector.
Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties. Cleaning the Air Filter Replacing the Air Filter Parent topic: Projector Maintenance Related references Projector Light Status Cleaning the Air Filter You need to clean the projector's air filter in the following situations: • The filter or vents get dusty. • You see a message telling you to clean it. 1. Turn off the projector and unplug the power cord. 2.
3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter. 6. Place the air filter back in the projector as shown. 7. Close the air filter cover.
• If the filter is a dark gray color You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1. Turn off the projector and unplug the power cord. 2. Press in on the inner edge of the air filter cover to release the latch, then pull to remove. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down until it locks into place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage.
Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands.
3. Insert the batteries with the + and – ends facing as shown. 4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport or ship the projector safely: • Remove any equipment connected to the projector. • When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image Problems Solving Projector or Remote Control Operation Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on. If this does not solve the problem, check the following: • The lights on the projector may indicate what the problem is.
1 Status light 2 Lamp light 3 Temp light 4 Power light Power light Status light Lamp light Temp light Status and solution Blue Blue Off Off Normal operation Blue Flashing blue Off Off Warming up; wait for an image to appear Off Off Off Off Standby or sleep mode 108
Power light Status light Lamp light Temp light Status and solution Blue Flashing blue Off Off Shutting down; when the Status light stops flashing, you can unplug the projector Flashing blue Varies Off Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too hot Off Flashing blue Off Orange Projector has overheated and turned
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem Off • Check to see if the lamp is burned out, broken, or installed incorrectly; reseat or replace the lamp as necessary • Clean or replace the air filter • If operating the projector at high altitude, turn on High Altitude Mode • If the problem persists, unplug the projector and contact Epson for help Flashing blue Varies Flashing orange Off Replace the lamp soon to avoid damage; do no
Related tasks Cleaning the Air Filter Replacing the Lamp Replacing the Air Filter Solving Image Problems Check the solutions in these sections if you have any problems with projected images.
• For images projected from applications using Windows DirectX, turn off DirectX functions. Parent topic: Solving Image Problems Related references Image Quality Settings - Image Menu Projector Setup Settings - Extended Menu Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press the source button on the projector repeatedly to cycle through the available sources. Wait a few seconds for an image to appear.
Parent topic: Solutions When "No Signal" Message Appears Displaying From a Mac Laptop If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) 1. Open the System Preferences utility and select Displays. 2. Select the Display or Color LCD option, if necessary. 3. Click the Arrange or Arrangement tab. 4. Select the Mirror Displays checkbox.
Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When the Image is Not Rectangular If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. • If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape.
• If you connected an extension power cable, try projecting without it to see if it caused interference in the signal. Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens.
• Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Advanced, and/or Color Saturation. • Make sure you selected the correct PC Signal or Video Signal setting on the Extended menu, if available for your image source. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.
• If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the Signal menu. Return the setting to its original value if changing it does not solve the problem.
Related references Projector Feature Settings - Settings Menu Related tasks Connecting the WirelessHD Transmitter Switching WirelessHD Sources Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Replacing the Remote Control Batteries Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries. • Make sure you are operating the remote control within the reception angle and range of the projector. • Make sure the projector is not warming up or shutting down.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada). Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution 1920 × 1080 pixels Lens F=2.3 to 3.
Image size 30 inches (0.76 m) to 300 inches (7.62 m) (in native aspect ratio) Projection distance 34 inches (0.87 m) to 754 inches (19.15 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:9 (width-to-height) Focus adjustment Manual Zoom adjustment Manual (optical) Zoom ratio 1-2.
Remote Control Specifications Reception range 32 feet (10 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 5.51 inches (140 mm) Width 18.35 inches (466 mm) Depth 15.55 inches (395 mm) Weight PowerLite Home Cinema 5030UB: 18.4 lb (8.4 kg) PowerLite Home Cinema 5030UBe: 18.9 lb (8.
Projector Environmental Specifications Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity (relative, noncondensing) Operating: 20 to 80% Operating altitude Up to 4921 feet (1500 m) Storage: 10 to 90% Up to 7500 feet (2286 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 60 1366 × 768 60/75/85 1280 × 800 70/75/85 1152 × 864 60 1280 × 960 60 1280 × 1024 60 1600 × 900 TV (NTSC) 60 720 × 480 TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 576 TV (NTSC4.
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 MHL input signals (PowerLite Home Cinema 5030UBe) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 HDMI 3D Signals Display format Refresh rate (in Hz) Resoluti
Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV750p (720p) 50/60 1280 × 720 Side by Side Top and Bottom HDTV1125i (1080i) 50/60 1920 × 1080 Side by Side HDTV1125p (1080p) 50/60 1920 × 1080 — 24 1920 × 1080 Side by Side Top and Bottom Parent topic: Technical Specifications 127
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
muscle twitching, loss of awareness, altered vision, involuntary movements, disorientation, eye strain, nausea/vomiting, dizziness, headaches, fatigue, or blurry/double vision that lasts longer than few seconds. Do not engage in any potentially hazardous activity (such as driving a vehicle or operating machinery) until your symptoms have completely gone away.
• Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects • SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. • Do not leave the 3D glasses or any parts supplied with the glasses within reach of children. They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor immediately.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment.
This projector product includes the open source software programs which apply the GNU General Public License Version 2 or later version ("GPL Programs"). We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's Guide.
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail.
The list of LGPL Programs is as follows and the names of author are described in the source code of the LGPL Programs. LGPL Programs glibc-2.8 SDL-1.2.13 SDL-Image The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright ©) 1991, 1999 Free Software Foundation, Inc.
source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library".
a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5.
and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.
Copyright (c) This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
2. You can use this software for whatever you want. You don't have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code. In legalese: The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose.
It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant and with the following additions to the disclaimer: There is no warranty against interference with your enjoyment of the library or against infringement.
Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc.
zlib-1.1.4 License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows. Copyright notice: (c) 1995-1998 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work. 2. Grant of Copyright License.
Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License. 5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.
that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives. Copyright [yyyy] [name of copyright owner] Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.
Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses.
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. ----------The author of this software is David M. Gay.
5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W. Sandmann This file may be freely distributed as long as the author's name remains. (6) Eric Backus (C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software. (7) Sun Microsystems Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved. Developed at SunPro, a Sun Microsystems, Inc. business.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
USA (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
DISCLAIMED.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (19) Todd C. Miller Copyright (c) 1998 Todd C. Miller All rights reserved.
Intel hereby grants you permission to copy, modify, and distribute this software and its documentation. Intel grants this permission provided that the above copyright notice appears in all copies and that both the copyright notice and this permission notice appear in supporting documentation.
(27) Konstantin Chuguev (--enable-newlib-iconv) Copyright (c) 1999, 2000 Konstantin Chuguev. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (30) - Alex Tatmanjants (targets using libc/posix) Copyright (c) 1995 Alex Tatmanjants at Electronni Visti IA, Kiev, Ukraine. All rights reserved.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Copyright (c) 2009 CodeSourcery, Inc. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
* * Neither the name of MIPS Technologies Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. TOPPERS/JSP This projector product includes the open source software program "TOPPERS/JSP" which applies the terms and conditions provided by owner of the copyright to the "TOPPERS/JSP".
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.). (b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided otherwise. (4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
This product includes software developed by the University of California, Berkeley and its contributors. 4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software. This software is something that is provided with no guarantee. The above copyright holder and the TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of its application.
A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law. Parent topic: Copyright Notice Copyright Attribution © 2014 Epson America, Inc.
