PowerLite® W16SK User's Guide
Contents PowerLite W16SK User's Guide ................................................................................................................. 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Additional Components ..............................................
Connecting to an External Computer Monitor................................................................................ Connecting to External Speakers .................................................................................................. Installing Batteries in the Remote Control .......................................................................................... Opening the Lens Covers.....................................................................................................
Entering a Password to Use the Projector................................................................................. Locking the Projector's Buttons ..................................................................................................... Unlocking the Projector's Buttons ............................................................................................. Installing a Security Cable ....................................................................................................
Using the Projector Help Displays .................................................................................................... Solving Image or Sound Problems ................................................................................................... Solutions When No Image Appears............................................................................................. Solutions When "No Signal" Message Appears...........................................................................
3D Safety Instructions ................................................................................................................. Restriction of Use ........................................................................................................................ Trademarks ...................................................................................................................................... Open Source Software License.............................................................
PowerLite W16SK User's Guide Welcome to the PowerLite W16SK User's Guide.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Parent topic: Introduction to Your Projector Additional Components Depending on how you plan to use the projector, you will need to obtain the following additional components: • To receive a composite video signal, you need three RCA-style video or A/V cables and a splitter that supports composite video signals. See your local computer or electronics dealer for purchase information.
Related references Optional Equipment and Replacement Parts Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Warranty and Registration Information Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty that came with your projector. In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.
Related tasks Using the Projector Help Displays Projector Part Locations Check the projector part illustrations to learn about the parts on your projector. Projector Parts - Front/Top Projector Parts - Rear Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control Parent topic: Introduction to Your Projector Projector Parts - Front/Top Note: The parts listed here are available on both projectors.
1 Exhaust vent 2 Commander projector 3 Lamp cover 4 Control panel 5 Projector status lights 6 Security cable attachment point and Kensington security lock slot 15
7 Speaker 8 Air filter cover and intake vent 9 Stacking mount connector 10 Stacking mount 11 Stacking mount angle adjustment 12 Zoom ring 13 Focus ring 14 Screen Fit sensor 15 Remote receiver 16 Polarizing filter 17 Receiver projector 18 Front adjustable foot 19 A/V Mute slide lever Parent topic: Projector Part Locations Related references Projector Light Status Related tasks Installing a Security Cable 16
Projector Parts - Rear 1 Audio ports 2 S-Video port 3 USB-A/document camera port (used on the commander projector for connection to the receiver projector; port is not functional on the receiver projector when the projectors are being used together in a stacked configuration) 4 USB-B port (used on the receiver projector for connection to the commander projector; port is not functional on the commander projector when the projectors are being used together in a stacked configuration) 17
5 HDMI port 6 Computer1 port 7 Monitor Out/Computer2 port 8 Audio Out port 9 Commander projector 10 Receiver projector 11 Remote receiver 12 RS-232C port (port is not functional on the receiver projector when the projectors are being used together in a stacked configuration) 13 AC input port 14 Video port Parent topic: Projector Part Locations 18
Projector Parts - Base 1 Front adjustable foot 2 Mounting bracket holes 3 Security cable attachment point 4 Rear adjustable feet Parent topic: Projector Part Locations 19
Projector Parts - Control Panel 1 Power button 2 Source Search button (searches for connected sources) 3 Enter button (selects options) 4 Arrow buttons 5 Help button (accesses projector help information) 6 Esc button (cancels/exits functions) 7 Volume control buttons and arrow buttons 8 Menu button (accesses projector menu system) 20
9 Screen Fit button (superimposes projector images) 10 Focus Help button (button is not functional when the projectors are being used together in a stacked configuration) Parent topic: Projector Part Locations 21
Projector Parts - Remote Control 1 Power button 22
2 Computer button (cycles through connected computer sources) 3 Video button (cycles through connected video sources) 4 Screen Fit button (superimposes projector images) 5 Numeric buttons (enter numbers) 6 Auto button (automatically adjusts position, tracking, and sync settings) 7 Aspect button (selects the image aspect ratio) 8 Num button (when held down, switches numeric buttons to number function) 9 Menu button (accesses projector menu system) 10 Arrow buttons (move through on-screen opt
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Covers Projector Placement You can place the projector on almost any flat surface to project your presentation. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling 25
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
16:10 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Screw hole number (2) Minimum to Maximum 80 inches (203 cm) 97 to 106 inches 4 (248 to 270 cm) 100 inches (254 cm) 122 to 133 inches 3 (310 to 338 cm) 120 inches (305 cm) 147 to 160 inches 2 (373 to 407 cm) 150 inches (381 cm) 184 to 200 inches 1 (467 to 509 cm) 4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Screw hole number (2) Minimum to Maximum 80 inches (203 cm) 110 to 121 i
Screen or image size Projection distance (1) Screw hole number (2) Minimum to Maximum 80 inches (203 cm) 100 to 109 inches 4 (255 to 278 cm) 100 inches (254 cm) 125 to 137 inches 3 (319 to 348 cm) 120 inches (305 cm) 151 to 165 inches 2 (383 to 418 cm) 150 inches (381 cm) 189 to 206 inches 1 (479 to 523 cm) Parent topic: Projector Placement Projector Connections You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images,
Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your game console documentation for instructions.
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your game console documentation for instructions.
Parent topic: Connecting to Video Sources Related tasks Connecting to a Video Source for Sound Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using optional RCAstyle video or A/V cables and a splitter that supports composite video signals. Note: If your video source has two composite video ports, you may not need a splitter. 1. Connect a cable with the yellow connector to your video source's yellow video output port.
Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports. Connect the projector to the video source using an RCA audio cable. 1. Connect the audio cable to your video source's audio-out ports. 2. Connect the other end of the cable to the Audio ports on either one of the projectors.
2. Connect a VGA computer cable to your computer's monitor port. Then connect the other end of the cable to the commander projector's Computer1 port. 3. Connect a VGA computer cable between the commander projector's Computer2 port and the receiver projector's Computer1 port. 4. Change the Monitor Out Port setting in the projector's Extended menu to Monitor Out. 5. Tighten the screws on the VGA connectors.
3. Connect a VGA computer cable between each projector's Computer port and the splitter. Note: If you choose the Computer2 ports, you may need to change the Monitor Out Port setting in the projector's Extended menu. 4. Tighten the screws on the VGA connectors.
2. Connect an HDMI cable between each projector's HDMI port and the splitter. Note: The projector will convert the digital audio signal sent from your computer into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers.
Parent topic: Connecting to Computer Sources Connecting to an External Computer Monitor If you connected the projector to a computer using a Computer port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible. Note: Monitors that use a refresh rate less than 60 Hz may not be able to display images correctly. 1. Make sure your computer is connected to the projector's Computer port.
1. Make sure your computer or video source is connected to the projector with both audio and video cables as necessary. 2. Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pinjack cable, or another type of cable or adapter. 3. Connect one end of the cable to your external speakers as necessary. 4. Connect the stereo mini-jack end of the cable to the Audio Out port on either one of the projectors.
1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Opening the Lens Covers 1. To open the projectors' lens covers, slide each projector's A/V Mute slide lever. 2. To cover the lenses or temporarily turn off the projected picture and sound, slide the A/V Mute slide covers closed.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Open the projectors' lens covers. 2. Connect the power cords to the projectors' power inlets.
3. Plug the power cords into an electrical outlet. The projectors' power lights turn orange. This indicates that the product is receiving power, but is not yet turned on (it is in standby mode). Note: With Direct Power On turned on, the product turns on as soon as you plug it in. 4. Press the power button on the commander projector or the remote control to turn on the product. The projectors beep and the power lights flash green as the product warms up.
2. Press the power button again. (To leave it on, press any other button.) The projectors beep twice, the lamps turn off, and the power lights turns orange. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the product for transport right away (if necessary). Caution: Do not turn the projector on immediately after turning it off. Turning the projector on and off frequently may shorten the life of the lamp. 3.
4. Close the projectors' lens covers. Parent topic: Using Basic Projector Features Viewing 3D Images You can view 3D images using your projector. 1. Connect a 3D-compatible video device to the projector using compatible HDMI cables. You may also need a splitter that supports 3D signals. 2. Turn on the video device, then turn on the projector. 3. Begin playback from the video device. Note: Make sure you set the video device to play content in 3D mode.
4. Press the 2D/3D button on the remote control to activate 3D mode, if necessary. 5. Put on your passive 3D glasses.
1 30º Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
3. If the image is tilted, rotate the rear feet to adjust their height. After you adjust the image, you must reapply the Screen Fit feature to correctly superimpose the projectors' images. See your Setup Guide for instructions. Parent topic: Using Basic Projector Features Resizing the Image With the Zoom Rings 1. Turn on the product and display an image. 2. To enlarge or reduce the image size, rotate the projectors' zoom rings.
After you resize the image using the zoom rings, you must reapply the Screen Fit feature to correctly superimpose the projectors' images. See your Setup Guide for instructions. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Rings 1. Turn on the product and display an image. 2. To sharpen the image focus, rotate the projectors' focus rings.
1 19.7 feet (6 m) 2 ± 30º 3 ± 15º Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
2. For video image sources, insert a DVD or other video media and press its play button (if necessary). 3. Do one of the following: • Press the Source Search button on the projector or remote control until you see the image from the source you want. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
2 Video and HDMI sources Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
The image disappears briefly and reappears flipped top-to-bottom. 3. To change projection back to the original mode, hold down the A/V Mute button for five seconds again. Parent topic: Projection Modes Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4.
Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Available Image Aspect Ratios You can select the following image aspect ratios, depending on the input signal from your image source. Note: When the projector is in 3D mode, the aspect ratio is automatically set to Normal. Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal.
Related references Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode.
Color Mode Description Photo Best for still images projected in a bright room Sports Best for television images in a bright room (video, S-Video, or composite video input only) sRGB Best for standard sRGB computer displays Blackboard Best for presentations onto a green chalkboard (adjusts the colors accordingly) Whiteboard Best for presentations onto a whiteboard (adjusts the colors accordingly) 3D Images Color Mode Description Dynamic Best for video games in a bright room 3D Presentation B
3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and select On. Note: You can turn Auto Iris on or off for each Color Mode that supports the feature. You cannot change the Auto Iris setting when you are using a Closed Caption setting. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Controlling the Volume with the Volume Buttons You can use the Volume buttons on the projector or the remote control to adjust the volume as you project a presentation with audio.
2. To lower or raise the volume, press the Volume buttons on the remote control or these buttons on the control panel. A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, you can set the volume using a projector menu.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Stopping Video Action Temporarily Zooming Into and Out of Images Projector Security Features Using the Projectors Individually Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation.
1. Press the Freeze button on the remote control to stop the video action. Note: The superimposed images may slip out of sync while the video action is stopped. 2. To restart the video action in progress, press Freeze again. Parent topic: Adjusting Projector Features Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 1. Press the E-Zoom + button on the remote control.
• To zoom out of the image, press the E-Zoom – button as necessary. • To return to the original image size, press Esc. Parent topic: Adjusting Projector Features Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings.
3. After the projector warms up, hold down the Freeze button on the remote control until you see the Password Protect menu. This takes about five seconds. 4. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 5. Select Yes and press Enter. 6. Hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 7. Enter the password again.
9. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, press Enter again, and press Esc. 10. To prevent changes to the User's Logo screen or related display settings, select User's Logo Protect, press Enter, select On, press Enter again, and press Esc. 11. Press the power button on the remote control. The commander projector turns off. 12. Wait a few moments, then press the power button on the projector or the remote control.
1. Hold down the Num button on the remote control while you enter the password using the numeric buttons. The password screen closes. 2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support.
2. Select the Settings menu and press Enter. 3. Select the Control Panel Lock setting and press Enter. 4. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 5. Select Yes and press Enter.
• Use the security cable attachment points on the projectors to attach wire cables and secure them to a room fixture or heavy furniture. Parent topic: Projector Security Features Related references Optional Equipment and Replacement Parts Using the Projectors Individually You can use either projector individually if necessary. You can leave them stacked together or remove them from their stacking mounts.
When the projector is in this mode, it functions like a PowerLite W16 projector, but without the following PowerLite W16 features: • 3D • Projection from an external USB device • Automatic vertical and horizontal keystone correction • Screen Fit • Focus Help See the PowerLite W16 User's Guide for instructions when using the projector in this mode.
7. Press Menu or Esc to exit the menus. 8. Turn off the product. 9. Unplug the power cords. 10. Disconnect the USB cable. 11. Remove the stacking mount angle adjustment screws (on both sides). 12. Loosen the stacking mount connector screws (on both sides).
13. Separate the commander and receiver projectors.
14. Remove the stacking mounts from the projectors.
When the projector's Stack Mode setting is set to Off, it functions like a PowerLite W16 projector, but without 3D capabilities. See the PowerLite W16 User's Guide for instructions when using the projector with stack mode deactivated. Restacking the Projectors Parent topic: Using the Projectors Individually Restacking the Projectors You can restack the projectors after separating them and set them up for use together again. Note: This procedure requires you to turn each projector on and off individually.
1. Turn on one of the projectors using the power button on the control panel. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Operation setting and press Enter. 5. Select the Stack Mode setting and press Enter. 6. Do one of the following: • If you are using the commander projector, select Commander and press Enter. The commander projector has a 1 label on the bottom. • If you are using the receiver projector, select Receiver and press Enter.
11. See the Setup Guide to continue the stacking process.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
To change settings for an input source, make sure the source is connected and select that source.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Progressive Off Sets whether to convert interlaced-to-progressive signals for certain video image types Video Film/Auto Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Noise Reduction Off Reduces flickering in analog images in two levels NR1 NR2 HDMI Video Range Normal Expanded Auto Sets the video range to match the setting of the device connected to the HDMI input port Auto: detects the video ran
Setting Options Description Video Signal Auto Specifies the signal type from the input sources connected to the video ports Various video standards Auto: detects signals automatically Aspect See the list of available aspect ratios Sets the aspect ratio (width-toheight ratio) for the selected input source Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Parent topic: Adjusting the Menu Settings Related references Avai
Setting Options Description Adjust Commander Pos.
Setting Options Description User Button Power Consumption Assigns a menu option to the User button on the remote control for one-touch access Info Progressive Closed Caption Resolution Parent topic: Adjusting the Menu Settings Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation.
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen A/V Mute Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and se
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode Timer Lens Cover Timer High Altitude Mode Monitor Out Port Stack Mode Sleep Mode: automatically turns off the projector after an interval of inactivity Sleep Mode Timer: sets the interval for Sleep Mode Lens Cover Timer: automatically turns off the projector after 30 minutes if the lens cover is closed High Al
First select either the commander projector or receiver projector in the menu and press Enter. You see a menu like this: Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
Information item Description Status Displays information about projector problems that may be needed by a service technician Serial Number Displays the projector's serial number Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Projector Lamp Specifications Projector Reset Options - Reset Menu You can reset the projectors' lamp usage timers to zero when you replace the lamps using the Reset Lamp Hours options.
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove dust or smudges, gently wipe the lens with lens-cleaning paper. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it.
Cleaning the 3D Glasses To remove dust, dirt, smudges, or fingerprints from the glasses, use a soft, dry, lint-free cloth. Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap.
If regular maintenance is not performed, your Epson projector will notify you when the temperature inside the projector has reached a high level. Do not wait until this warning appears to maintain your projector filter as prolonged exposure to high temperatures may reduce the life of your projector or lamp. Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove an air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Caution: Do not use canned air. The gases may leave a residue or push dust and debris into the projector's optics or other sensitive areas. 3. If dust is difficult to remove or an air filter is damaged, replace the air filter.
Note: Along with the message, you will also see an indicator like this. Projector 1 represents the commander and projector 2 represents the receiver. The green arrow points to the projector that the message is referring to. You can replace the air filter while the projector is mounted to the ceiling, if necessary. The illustrations here show the projector placed on a table.
2. Place your finger into the groove at the top of the air filter cover and pull to open the cover.
3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The product keeps track of the number of hours the lamps are used and displays this information in the product's menu system.
Replacing the Lamp Resetting the Lamp Timer Parent topic: Projector Maintenance Related references Projector Information Display - Info Menu Optional Equipment and Replacement Parts Projector Lamp Specifications Replacing the Lamp Before you replace the lamp, let the product cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the product is mounted to the ceiling, if necessary.
3. If you need to replace the lamp in the receiver projector, remove the stacking mount angle adjustment screws on both sides (and note which screw hole number you used). Then tilt the commander projector back so that you can access the receiver projector's lamp. Warning: If the projector is installed on the ceiling, make sure to secure the commander projector so that it does not fall out of the stacking mount. If the projector falls, it may injure you or damage the projector.
4. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. If the projector is installed on the ceiling, stand to the side of the lamp cover and not underneath it; pieces of glass could fall into your eyes or mouth when you open the lamp cover. 5. Slide the lamp cover out and lift it off.
6. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 7. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
8. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down until it locks into place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 9. Push in the lamp firmly and tighten the screws to secure it.
10. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. 11. If you replaced the receiver projector's lamp, tilt the commander projector forward and reattach the stacking mount angle adjustment screws. Warning: When you tilt the commander projector forward, be careful not to pinch your fingers in the mounts. Reset the lamp timer to zero to keep track of the new lamp’s usage.
2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select the Reset Lamp Hours option for the projector in which you replaced the lamp and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries.
1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Operation Transporting the Projector The projector contains precision parts, some of which are glass.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Where to Get Help Projection Problem Tips If the product is not working properly, try turning it off and unplugging the projectors. Then plug them back in and turn the product on.
1 Power light 2 Lamp light 3 Temperature light Power light Lamp light Temperature light Status and solution Green Off Off Normal operation. Flashing green Off Off Warming up. Wait for an image to appear. Orange Off Off Standby or sleep mode. Flashing orange Off Off Shutting down. (When the light remains orange, you can unplug the projector.) Flashing red Flashing orange Projector is too hot.
Power light Lamp light Temperature light Status and solution Red Off Red Projector has overheated and turned off. Leave it turned off to cool down. Once the temperature light turns off and the power light turns orange (after about five minutes), try the suggestions below: • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter. • If operating the projector at high altitude, turn on High Altitude Mode.
Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Where to Get Help Related tasks Cleaning the Air Filter and Vents Replacing the Air Filter Replacing the Lamp Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Help button on the projector or the remote control. You see the Help menu. 3.
Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect Solutions When a 3D Image Does Not Display Correctly Solutions When No Image Appears on an External Monitor Solutions to Sound Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens covers are open. • Press the A/V Mute button on the remote control to see if the image was temporarily turned off.
Related references Projector Setup Settings - Extended Menu Input Signal Settings - Signal Menu Projector Feature Settings - Settings Menu Related tasks Unlocking the Projector's Buttons Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press the Source Search button and wait a few seconds for an image to appear. • Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary.
Displaying From a Mac Laptop If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) 1. Open the System Preferences utility and select Displays. 2. Select the VGA Display or Color LCD option, if necessary. 3. Click the Arrange or Arrangement tab. 4. Select the Mirror Displays checkbox.
Related references Supported Video Display Formats Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector.
• If you are projecting from a computer, press the Auto button on the remote control to automatically adjust the tracking and sync. • Repeat the Screen Fit process to superimpose the projectors' images. See your Setup Guide for instructions. • If you are projecting from a computer, use a lower resolution.
Solutions When a 3D Image Does Not Display Correctly If a 3D image does not display correctly, try the following solutions: • Press the 2D/3D button on the remote control to switch to 3D mode, if necessary. You can also activate 3D mode by setting the 3D Display setting on the Signal menu to On. • Make sure your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information. • Make sure you are using HDMI cables that support 3D signals.
• Make sure you set the Monitor Out Port setting to Monitor Out. Parent topic: Solving Image or Sound Problems Related references Projector Setup Settings - Extended Menu Solutions to Sound Problems If there is no sound when you expect it or the volume is too low, try the following solutions: • Adjust the projector's volume settings. • Press the A/V Mute button on the remote control to resume video and audio if they were temporarily stopped.
Solutions to Projector Power or Shut-Off Problems If the product does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cords are securely connected to the product and to a working electrical outlet. • The product's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the product. • The power cords may be defective. Disconnect the cords and contact Epson.
Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries. • Make sure you are operating the remote control within the reception angle and range of the projector. • Make sure the projector is not warming up or shutting down.
Parent topic: Solving Projector or Remote Control Operation Problems Related references Where to Get Help Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Parent topic: Solving Problems Related tasks Using the Projector Help Displays 122
Technical Specifications These sections list the technical specifications of your projector.
Optical aspect ratio 16:10 (width-to-height) Focus adjustment Manual Zoom adjustment Manual (optical) Zoom ratio 1:1.2 (Minimum-to-Maximum) Internal sound system 2 W monaural (for each projector) Noise level 39 dB (Normal Power Consumption mode) 32 dB (ECO Power Consumption mode) Keystone correction angle Vertical: ± 15º (normal screen); ± 10º (silver screen) Horizontal: ± 15º (normal screen); ± 10º (silver screen) USB Type B port compatibility USB 1.1 and 2.
Remote Control Specifications Reception range 19.7 feet (6 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Note: These specifications apply to the product when the projectors are stacked. Height (excluding feet) 7.76 inches (197 mm) Width 14.6 inches (372 mm) Depth 13.8 inches (350 mm) Weight 17.4 lb (7.
Power consumption Operating: (220 to 240 V) Normal Power Consumption mode: 277 W ECO Power Consumption mode: 230 W Standby: 0.40 W (Communication Off), 3.
Projector Safety and Approvals Specifications United States Stacked configuration: FCC Part 15B Class A (DoC) UL60950-1 2nd edition (cTUVus Mark) Single projector configuration: FCC Part 15B Class B (DoC) UL60950-1 2nd edition (cTUVus Mark) Canada Stacked configuration: ICES-003 Class A CSA-C22.2 No. 60950-1-07 (cTUVus Mark) Single projector configuration: ICES-003 Class B CSA-C22.2 No.
Display format Refresh rate (in Hz) Resolution (in pixels) XGA 60/70/75/85 1024 × 768 WXGA 60/75/85 1280 × 800 60 1280 × 768 60 1366 × 768 60/75/85 1440 × 900 60 1600 × 900 70/75/85 1152 × 864 60/75/85 1280 × 960 60/75/85 1280 × 1024 SXGA+ 60/75 1400 × 1050 UXGA 60 1600 × 1200 WSXGA+* 60 1680 × 1050 MAC13" 67 640 × 480 MAC16" 75 832 × 624 MAC19" 75 1024 × 768 59 1024 × 768 75 1152 × 870 TV (NTSC) 60 720 × 480 TV (PAL) 50/60 720 × 576 TV (SECAM) 50 720 × 5
Display format Refresh rate (in Hz) Resolution (in pixels) VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 WSXGA+ 60 1680 × 1050 SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 HDMI input signals
Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV1125p (1080p) 24 1920 × 1080 Frame Packing Top and Bottom 50/60 1920 × 1080 Parent topic: Technical Specifications 130 Side by Side
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to www.epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
3D Safety Instructions Follow these 3D safety instructions when setting up and using the projector: • If you or any viewer experiences the following symptoms or other major discomfort from viewing 3D video images, immediately stop viewing and contact your health care provider: convulsions, eye or muscle twitching, loss of awareness, altered vision, involuntary movements, disorientation, eye strain, nausea/vomiting, dizziness, headaches, fatigue, or blurry/double vision that lasts longer than few seconds.
People who are sleep deprived People who are physically tired People under the influence of drugs or alcohol Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. • Do not leave the 3D glasses or any parts supplied with the glasses within reach of children. They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor immediately.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices Open Source Software License GNU GPL This projector product includes the open source software programs which apply the GNU General Public License Version 2 or later version ("GPL Programs").
• EPSON original drivers • Stonestreet One Drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9.
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs").
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6.
with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. libjpeg This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg".
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation. (2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent JPEG Group".
"The Graphics Interchange Format(c) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated." libpng This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng". The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of libpng progra libpng-1.2.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors: Tom Lane Glenn Randers-Pehrson Willem van Schaik libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source. 3. This Copyright notice may not be removed or altered from any source or altered source distribution. The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. 3. This notice may not be removed or altered from any source distribution. Jean-loup Gailly jloup@gzip.org Mark Adler madler@alumni.caltech.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib".
* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved. Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (12) SuperH, Inc. Copyright 2002 SuperH, Inc.
3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Author: S. L. Moshier. Copyright (c) 1984,2000 S.L. Moshier Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
results of the use of, the software and documentation in terms of correctness, accuracy, reliability, currentness, or otherwise; and you rely on the software, documentation and results solely at your own risk. IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE PRODUCT LICENSED HEREUNDER.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(32) - Andrey A. Chernov (targets using libc/posix) Copyright (C) 1996 by Andrey A. Chernov, Moscow, Russia. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (35) - ARM Ltd (arm and thumb variant targets only) Copyright (c) 2009 ARM Ltd All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
* Neither the name of CodeSourcery nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY CODESOURCERY, INC. "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED.
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. /* Parent topic: Notices Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
1/13 CPD-38063 Parent topic: Copyright Notice 179