Color Inkjet Printer Service Manual
Table Of Contents
- EPSON Stylus Photo R300/R310
- TROUBLESHOOTING
- DISASSEMBLY AND ASSEMBLY
- 2.1 Overview
- 2.2 Caution regarding assembling/disassembling the printer mechanism, a·Yl|Z6±¬¨–‹šÒq¿GZ~YçlçXX
- 2.3 Disassembly
- 2.3.1 Removing Paper Support Assy.
- 2.3.2 Removing Housing, Upper
- 2.3.3 Removing Housing, Middle
- 2.3.4 Removing Porous Pad, Paper Guide, Front
- 2.3.5 Removing Panel Board
- 2.3.6 Removing Stacker Assy.
- 2.3.7 Removing Main Board
- 2.3.8 Removing ASF Assy.
- 2.3.9 Removing Holder, Shaft Assy.
- 2.3.10 Removing CR Motor
- 2.3.11 Removing APG Assy.
- 2.3.12 Removing Print Head
- 2.3.13 Removing Carriage Unit
- 2.3.14 Removing Paper Guide, Upper
- 2.3.15 Removing Printer Mechanism/ Housing, Lower
- 2.3.16 Removing Power Supply Unit
- 2.3.17 Removing CDR Guide Assy.
- 2.3.18 Removing Ink System
- 2.3.19 Removing Paper Guide, Front/Roller EJ Assy.
- 2.3.20 Removing PF Motor
- ADJUSTMENT
- 3.1 Adjustment Items and Overview
- 3.2 Adjustment by using adjustment program
- 3.2.1 Market Setting
- 3.2.2 USB ID Input
- 3.2.3 Head ID Input
- 3.2.4 Head Angular Adjustment
- 3.2.5 Bi-d Adjustment
- 3.2.6 PW Sensor Adjustment
- 3.2.7 First Dot Adjustment
- 3.2.8 Offset Input for CR Motor Calorific Limitation
- 3.2.9 A4 Normal Paper Print
- 3.2.10 A4 Photo Quality Inkjet Paper Print
- 3.2.11 A4 Photo Paper/ Glossy Photo Paper print
- 3.3 Adjustment Except Adjustment Program
- MAINTENANCE
- APPENDIX
EPSON Stylus Photo R300/R310 Revision A
TROUBLESHOOTING Unit Level Troubleshooting 22
Table 1-9. Check Points for CD/DVD Tray Error to Each Phenomenon
Occurrence Timing
Position of CR
Phenomenon Detail
Faulty Part/
Part Name
Check Point Remedy
When printing
CDR/DVDR
-
An error occurs even though "CDR
Tray" is set when printing CDR/DVDR.
CDR Tray
1. Check if the contact point of "CDR Tray" with "CDR
Tray Sensor" is not cracked.
1. Replace "CDR Tray" with a new one.
CDR Tray Sensor
1. Check if "CDR Tray Sensor" is connected to CN6 on
"Main Board".
2. Check if "CDR Tray Sensor" is not damaged.
3. Check if "CDR Tray Sensor Connector Cable" is not cut
off.
1. Connect "CDR Tray Sensor" to CN6 on
"Main Board".
2. Replace "CDR Tray Sensor" with a new one.
3. Replace "CDR Tray Sensor" with a new one.
Main Board
1. Check if any device on "Main Board" is not damaged. 1. Replace "Main Board" with a new one.
Contact point
CDR Tray Sensor