Color Inkjet Printer Service Manual
Table Of Contents
- EPSON Stylus Photo R300/R310
- TROUBLESHOOTING
- DISASSEMBLY AND ASSEMBLY
- 2.1 Overview
- 2.2 Caution regarding assembling/disassembling the printer mechanism, a·Yl|Z6±¬¨–‹šÒq¿GZ~YçlçXX
- 2.3 Disassembly
- 2.3.1 Removing Paper Support Assy.
- 2.3.2 Removing Housing, Upper
- 2.3.3 Removing Housing, Middle
- 2.3.4 Removing Porous Pad, Paper Guide, Front
- 2.3.5 Removing Panel Board
- 2.3.6 Removing Stacker Assy.
- 2.3.7 Removing Main Board
- 2.3.8 Removing ASF Assy.
- 2.3.9 Removing Holder, Shaft Assy.
- 2.3.10 Removing CR Motor
- 2.3.11 Removing APG Assy.
- 2.3.12 Removing Print Head
- 2.3.13 Removing Carriage Unit
- 2.3.14 Removing Paper Guide, Upper
- 2.3.15 Removing Printer Mechanism/ Housing, Lower
- 2.3.16 Removing Power Supply Unit
- 2.3.17 Removing CDR Guide Assy.
- 2.3.18 Removing Ink System
- 2.3.19 Removing Paper Guide, Front/Roller EJ Assy.
- 2.3.20 Removing PF Motor
- ADJUSTMENT
- 3.1 Adjustment Items and Overview
- 3.2 Adjustment by using adjustment program
- 3.2.1 Market Setting
- 3.2.2 USB ID Input
- 3.2.3 Head ID Input
- 3.2.4 Head Angular Adjustment
- 3.2.5 Bi-d Adjustment
- 3.2.6 PW Sensor Adjustment
- 3.2.7 First Dot Adjustment
- 3.2.8 Offset Input for CR Motor Calorific Limitation
- 3.2.9 A4 Normal Paper Print
- 3.2.10 A4 Photo Quality Inkjet Paper Print
- 3.2.11 A4 Photo Paper/ Glossy Photo Paper print
- 3.3 Adjustment Except Adjustment Program
- MAINTENANCE
- APPENDIX
Stylus Photo R300/R310 Revision A
DISASSEMBLY AND ASSEMBLY Overview 32
2.1 Overview
This section describes procedures for disassembling the main components of Stylus
Photo R300/R310. Unless otherwise specified, disassembly units or components can be
reassembled by reversing the disassembly procedure.
"WARNING" indicates procedures which may result in damage, injury or involving
human lives if you don't take extra care.
"CAUTION" indicates precautions for any disassembly or assembly procedures.
"CHECK POINT" indicates points to be checked.
"REASSEMBLY" indicates reassembling procedures which are different from the
reverse order of the disassembling.
"ADJUSTMENT REQUIRED" indicates required adjustments after the assembly and
the disassembly.
Read precautions described in the next section before starting.
2.1.1 Precautions
Before starting the disassembling/reassembling work of this product, always read the
descriptions under the following headings "WARNING" and "CAUTION" carefully.
W A R N I N G
Disconnect the power cable before disassembling or assembling
the printer.
If you need to work on the printer with power applied, strictly
follow the instructions in this manual.
Wear protective goggles to protect your eyes from ink. If ink gets
in your eye, flush the eye with fresh water and see a doctor
immediately.
Always wear gloves for disassembly and reassembly to avoid
injury from sharp metal edges.
To protect sensitive microprocessors and circuitry, use static
discharge equipment, such as anti-static wrist straps, when
accessing internal components.
Never touch the ink or wasted ink with bare hands. If ink comes
into contact with your skin, wash it off with soap and water
immediately. If you have a skin irritation, consult a physician.
When reassembling the waste ink pads and tray, always make
sure that the waste ink tube is fitted correctly in the specified
place. Fitting the ink tube in other than the specified position can
cause ink leakage.
W A R N I N G
Avant de commencer, assure vous que l’imprimante soit eteinte
et que le cordon d’alimentation soit debranche.
Veillez a jeter les piles usagees selon le reglement local.
C A U T I O N
Risque d’explosion si la pile est remplacée incorrectment. Ne
remplacer que par une pile du même type ou d’un type équivalent
recommandé par le fabricant. Eliminer les piles déchargées selon
les lois et les règles de sécurité en vigueur.
C A U T I O N
When transporting the printer after installing the ink cartridge,
be sure to pack the printer for transportation without removing
the ink cartridge.
Use only recommended tools for disassembling, assembling or
adjusting the printer. (Refer to Table 2-1 "Tool List".)
Observe the specified torque when tightening screws.
Use the specified lubricants and adhesives. (Refer to Chapter 4
for details.)
Make the specified adjustments when you disassemble the
printer. (Refer to Chapter 3 for details.)