Color Inkjet Printer Service Manual
Table Of Contents
- EPSON Stylus Photo R300/R310
- TROUBLESHOOTING
- DISASSEMBLY AND ASSEMBLY
- 2.1 Overview
- 2.2 Caution regarding assembling/disassembling the printer mechanism, a·Yl|Z6±¬¨–‹šÒq¿GZ~YçlçXX
- 2.3 Disassembly
- 2.3.1 Removing Paper Support Assy.
- 2.3.2 Removing Housing, Upper
- 2.3.3 Removing Housing, Middle
- 2.3.4 Removing Porous Pad, Paper Guide, Front
- 2.3.5 Removing Panel Board
- 2.3.6 Removing Stacker Assy.
- 2.3.7 Removing Main Board
- 2.3.8 Removing ASF Assy.
- 2.3.9 Removing Holder, Shaft Assy.
- 2.3.10 Removing CR Motor
- 2.3.11 Removing APG Assy.
- 2.3.12 Removing Print Head
- 2.3.13 Removing Carriage Unit
- 2.3.14 Removing Paper Guide, Upper
- 2.3.15 Removing Printer Mechanism/ Housing, Lower
- 2.3.16 Removing Power Supply Unit
- 2.3.17 Removing CDR Guide Assy.
- 2.3.18 Removing Ink System
- 2.3.19 Removing Paper Guide, Front/Roller EJ Assy.
- 2.3.20 Removing PF Motor
- ADJUSTMENT
- 3.1 Adjustment Items and Overview
- 3.2 Adjustment by using adjustment program
- 3.2.1 Market Setting
- 3.2.2 USB ID Input
- 3.2.3 Head ID Input
- 3.2.4 Head Angular Adjustment
- 3.2.5 Bi-d Adjustment
- 3.2.6 PW Sensor Adjustment
- 3.2.7 First Dot Adjustment
- 3.2.8 Offset Input for CR Motor Calorific Limitation
- 3.2.9 A4 Normal Paper Print
- 3.2.10 A4 Photo Quality Inkjet Paper Print
- 3.2.11 A4 Photo Paper/ Glossy Photo Paper print
- 3.3 Adjustment Except Adjustment Program
- MAINTENANCE
- APPENDIX
Stylus Photo R300/R310 Revision A
DISASSEMBLY AND ASSEMBLY Disassembly 44
2.3.5 Removing Panel Board
External View
Figure 2-12. Removing "Panel Board"
Parts/Units which should be removed before removing "Panel Board"
Paper Support Assy./Housing, Upper
Procedure for Removing
1. Remove the screws (x4) which secure "Board Assy., Panel". Then, remove
"Board Assy., Panel".
2. Remove the screw which secures "Panel Board". Then, remove "Panel Board"
from "Shield Plate, LCD".
3. Take off the two-sided tapes (x2) which secure "Cover, LCD" from the back
of "Housing, Upper". Then, remove "Cover, LCD".
Cover, LCD
Two-sided
Tapes
Switch
Line Mark
Board Assy., Panel
C.B.P 3x8 (4-6kgf•cm)
1
2
3
4
Shield Plate, LCD
C.B.S 3x8 (4-6kgf•cm)
Panel Board
LCD Panel
Rib and
Adjusting Hole
C A U T I O N
Do not damage "LCD Panel".
When removing "Panel Board Unit", the switch may detach and
drop. If this occurs, reinstall it referring the figure.
When looking at back side of "Housing, Upper", make sure that
the line mark of "Housing, Upper" securely comes to the position
shown in the figure.
Match the rib of "Shield Plate, LCD" and the positioning hole of
"Panel Board".
Screw "Board Assy., Panel" in the order as shown in the figure.