Color Inkjet Printer Service Manual
Table Of Contents
- EPSON Stylus Photo R300/R310
- TROUBLESHOOTING
- DISASSEMBLY AND ASSEMBLY
- 2.1 Overview
- 2.2 Caution regarding assembling/disassembling the printer mechanism, a·Yl|Z6±¬¨–‹šÒq¿GZ~YçlçXX
- 2.3 Disassembly
- 2.3.1 Removing Paper Support Assy.
- 2.3.2 Removing Housing, Upper
- 2.3.3 Removing Housing, Middle
- 2.3.4 Removing Porous Pad, Paper Guide, Front
- 2.3.5 Removing Panel Board
- 2.3.6 Removing Stacker Assy.
- 2.3.7 Removing Main Board
- 2.3.8 Removing ASF Assy.
- 2.3.9 Removing Holder, Shaft Assy.
- 2.3.10 Removing CR Motor
- 2.3.11 Removing APG Assy.
- 2.3.12 Removing Print Head
- 2.3.13 Removing Carriage Unit
- 2.3.14 Removing Paper Guide, Upper
- 2.3.15 Removing Printer Mechanism/ Housing, Lower
- 2.3.16 Removing Power Supply Unit
- 2.3.17 Removing CDR Guide Assy.
- 2.3.18 Removing Ink System
- 2.3.19 Removing Paper Guide, Front/Roller EJ Assy.
- 2.3.20 Removing PF Motor
- ADJUSTMENT
- 3.1 Adjustment Items and Overview
- 3.2 Adjustment by using adjustment program
- 3.2.1 Market Setting
- 3.2.2 USB ID Input
- 3.2.3 Head ID Input
- 3.2.4 Head Angular Adjustment
- 3.2.5 Bi-d Adjustment
- 3.2.6 PW Sensor Adjustment
- 3.2.7 First Dot Adjustment
- 3.2.8 Offset Input for CR Motor Calorific Limitation
- 3.2.9 A4 Normal Paper Print
- 3.2.10 A4 Photo Quality Inkjet Paper Print
- 3.2.11 A4 Photo Paper/ Glossy Photo Paper print
- 3.3 Adjustment Except Adjustment Program
- MAINTENANCE
- APPENDIX
Stylus Photo R300/R310 Revision A
DISASSEMBLY AND ASSEMBLY Disassembly 64
2.3.15 Removing Printer Mechanism/
Housing, Lower
External View
Figure 2-38. Removing "Printer Mechanism"/"Housing, Lower" (1)
Figure 2-39. Removing "Printer Mechanism"/"Housing, Lower" (2)
Parts/Units which should be removed before removing "Printer
Mechanism"/"Housing, Lower"
Paper Support Assy./Housing, Upper/Housing, Middle/Main Board Unit/
ASF Assy./Holder, Shaft Assy.
Procedure for Removing
1. Move "Carriage Unit" to the centre of the printer.
2. Remove the screws (x3) which secure "Paper Guide, CDR".
3. Remove the screws (x5) which secure "Printer Mechanism".
4. Take off the acetate tape and release the connector of "Star Wheel/CDR
Sensor".
5. Cut off the wire band and release the connector cable.
6. Release the hooks (x4) which secure "Printer Mechanism". Then, hold the
both right and left upper edges of "Frame, Main" and remove "Printer
Mechanism" to upward.
C.B.P 3x8 (5-7kgf•cm)
C.B.S 3x6 (5-7kgf•cm)
Paper Guide, CDR
1 2
3
C.B.P 3x10 (6-8kgfcm)
C.B.S 3x6 (6-8kgf•cm)
1
2
Screw, Frame, Main (6-8kgf•cm)
4
C.B.P 3x10 (6-8kgf•cm)
Hook
(Under the tube)
3
5
Wire Band
Lever, ChangeCombination
Gear, 27.2, 19.2
Hooks
Hook
Acetate Tape
2 ± 1mm
Handling Position