Color Inkjet Printer Service Manual
Table Of Contents
- EPSON Stylus Photo R300/R310
- TROUBLESHOOTING
- DISASSEMBLY AND ASSEMBLY
- 2.1 Overview
- 2.2 Caution regarding assembling/disassembling the printer mechanism, a·Yl|Z6±¬¨–‹šÒq¿GZ~YçlçXX
- 2.3 Disassembly
- 2.3.1 Removing Paper Support Assy.
- 2.3.2 Removing Housing, Upper
- 2.3.3 Removing Housing, Middle
- 2.3.4 Removing Porous Pad, Paper Guide, Front
- 2.3.5 Removing Panel Board
- 2.3.6 Removing Stacker Assy.
- 2.3.7 Removing Main Board
- 2.3.8 Removing ASF Assy.
- 2.3.9 Removing Holder, Shaft Assy.
- 2.3.10 Removing CR Motor
- 2.3.11 Removing APG Assy.
- 2.3.12 Removing Print Head
- 2.3.13 Removing Carriage Unit
- 2.3.14 Removing Paper Guide, Upper
- 2.3.15 Removing Printer Mechanism/ Housing, Lower
- 2.3.16 Removing Power Supply Unit
- 2.3.17 Removing CDR Guide Assy.
- 2.3.18 Removing Ink System
- 2.3.19 Removing Paper Guide, Front/Roller EJ Assy.
- 2.3.20 Removing PF Motor
- ADJUSTMENT
- 3.1 Adjustment Items and Overview
- 3.2 Adjustment by using adjustment program
- 3.2.1 Market Setting
- 3.2.2 USB ID Input
- 3.2.3 Head ID Input
- 3.2.4 Head Angular Adjustment
- 3.2.5 Bi-d Adjustment
- 3.2.6 PW Sensor Adjustment
- 3.2.7 First Dot Adjustment
- 3.2.8 Offset Input for CR Motor Calorific Limitation
- 3.2.9 A4 Normal Paper Print
- 3.2.10 A4 Photo Quality Inkjet Paper Print
- 3.2.11 A4 Photo Paper/ Glossy Photo Paper print
- 3.3 Adjustment Except Adjustment Program
- MAINTENANCE
- APPENDIX
EPSON Stylus Photo R300/R310 Revision A
MAINTENANCE Overview 99
<Lubrication Point>
Specified points on "Holder,
Scale, Left" in the figure on the
left
<Lubrication Type>
G-63
<Lubrication Amount>
8 points (Adequate dose)
<Remarks>
Use a brush to apply it
<Lubrication Point>
Specified points on "Holder,
Scale, Right" in the figure on the
left
<Lubrication Type>
G-63
<Lubrication Amount>
8 points (Adequate dose)
<Remarks>
Use a brush to apply it
Holder, Scale, Left
Inside surface of hole
Both sides close to upper surface
Upper surface Upper surface
Upper surface
Upper surface
Inside surface of hole
Holder, Scale, Right
Upper surface
Both sides
Both sides
Upper surface
Upper surface
Inside surface of hole
<Lubrication Point>
"Pulley, Driven Assy."
<Lubrication Type>
G-26
<Lubrication Amount>
1mm x 4 points
<Remarks>
Use a syringe to apply it
<Lubrication Point>
1. Upper surface of curving area
of "Holder, Idle Roller"
2. Lower surface of curving area
of "Holder, Idle Roller"
<Lubrication Type>
1. G-26
2. G-26
<Lubrication Amount>
1. 2 points (Adequate dose)
2. 2 points (Adequate dose)
<Remarks>
Use a brush to apply it
Pulley, Driven Assy.
1
2