RP-300-H Receipt Printer User’s Manual All specifications are subject to change without notice
TABLE OF CONTENTS 1. Parts Identifications 3 2. Setting up the printer 4 2.1 Unpacking 4 2.2 Connecting the cables 5 2.3 Loading the roll paper 9 2.4 Dip switch setting 11 3. Control panel and other functions 18 3.1 Control panel 18 3.2 Error Indicating 18 4. Self Test 19 5. Hexadecimal Dump 20 6. Specifications 21 6.1. General Specifications 21 6.2. Auto Cutter Specifications 23 6.3. Interface 23 6.4. Electrical Characteristics 23 6.5. Environmental Requirements 24 6.6.
RP-300-H User’s Manual 1.
RP-300-H User’s Manual 2. Setting Up the Printer 2-1. Unpacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.
RP-300-H User’s Manual 2-2. Connecting the Cables You can connect up the cables required for printing to the printer. They all connect to the connector panel on the back of the printer, which is shown below : Before connecting any of the cables, make sure that both the printer and the computer are turned off.
RP-300-H User’s Manual 2-2-1.
RP-300-H User’s Manual - Centronics Parallel interface PIN SIGNAL I/O 1 STROBEInput 2~9 DATA0~7 Input/Output 10 ACKOutput 11 BUSY Output 12 PE Output 13 SELECT Output 14 AUTO FEEDInput 15 GROUND 16 GROUND 17 NC 18 LOGIC-H 19~30 GROUND 31 INITInput 32 ERROROutput 33 GROUND 34 NC 35 +5V 36 SELLECT INInput DESCRIPTION Synchronize signal Data received Data bit Transmitted 0 ~7 Data receiving completed.
RP-300-H User’s Manual 2-2-2. Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 1.0A for 510ms or less when not printing. PIN 1 2 3 4 5 6 SIGNAL Signal GND Drawer kick-out drive signal 1 Drawer open/close signal +24V Drawer kick-out drive signal 2 Signal GND DESCRIPTION Output Input Output - Caution : To avoid an overcurrent, the resistance of the drawer kick-out solenoid must be 24 Ω or more.
RP-300-H User’s Manual 2-3. Loading the Roll Paper Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. (Turn off power switch) 1. Make sure that the printer is not receiving data; Otherwise, data may be lost. 2. Open the paper roll cover by pushing down the cover-open button. 3. Remove the used paper roll core if there is one inside. 4. Insert new paper roll as shown.
RP-300-H User’s Manual 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper, as shown. Then, close the cover. 7. Tear off the paper as shown.
RP-300-H User’s Manual 2-4. Dip Switch Setting The printer is set up at the factory to be appropriate for almost all users. On the other hand, offers some more settings for users with special requirements. It has DIP switches that allow you to change communication setting, such as handshaking and parity check, as well as print density. Your printer has two sets of DIP switches. The functions of the switches are shown in the following tables. ♦Note : Power off.
RP-300-H User’s Manual 2-4-2. Parallel Interface Specification DIP Switch Set 1 Functions SW FUNCTIONS 2 Hexadecimal 5 Bi-Parallel mode ON HEXDUMP DISABLED Print Density (DIP-SW2) Print Density Low Power Normal Normal Dark OFF NORMAL ENABLED SW-1 ON OFF ON OFF DEFAULT OFF OFF SW-2 ON ON OFF OFF 2-4-3.
RP-300-H User’s Manual 2-4-4.
RP-300-H User’s Manual 2-4-5. Wi-fi Specification DIP Switch Set 1 Function SW FUNCTION 2 Hexadecimal Print Density (DIP-SW2) Print Density Low Power Normal Normal Dark ON HEXDUMP OFF NORMAL SW-1 ON OFF ON OFF DEFAULT OFF SW-2 ON ON OFF OFF 2-4-6.
RP-300-H User’s Manual DIP Switch Set 2 Functions Cutter SW 3 FUNCTIONS Cutter ON FULL CUT Emulation FUNCTIONS Epson (TM-88) Paper low detect (*1) SW 6 OFF PARTIAL CUT SW-4 OFF FUNCTIONS Paper Low Remarks Only Epson mode SW-5 OFF ON Detect OFF Do not Detect (*1) The detecting function of [Paper Low] is an option. Please set Dip Switch (2-6) [OFF] if you don't need any option. If Dip Switch is [ON] without any special option purpose. Printer detects [Paper is Low] and it could cause error.
RP-300-H User’s Manual ♣CAUTION: Turn off the printer while removing the DIP switch cover to prevent an electric short, which can damage the printer. 1. Make sure the printer is turned off. 2. Remove the screw from the DIP switch cover. Then, take off the DIP switch cover as shown in the illustration below. G 3. Set the switches using a pointed tool, such as tweezers or a small screwdriver. 4. Replace the DIP switch cover. Then, secure it with the screw.
RP-300-H User’s Manual ♣CAUTION: When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming. 1. Make sure the printer is turned off. 2. Remove the screw from the DIP switch cover. Then, take off the DIP switch cover as shown in the illustration below. G 3. Turn screw with drivers to a direction until paper is released from the cutter.
RP-300-H User’s Manual 3. Control panel and other functions. 3-1. Control panel You can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you to monitor the printer’s status. Control Panel ڭڠڲڪګ ڭڪڭڭڠ ڭڠګڜګ ڟڠڠڡ Button The button can be disabled by the ESC c 5 command. Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed paper continuously. 3-2.
RP-300-H User’s Manual 4. Self Test The self-test lets you know if your printer is operating properly. It checks the control circuits, printer mechanisms, print quality, ROM version and DIP switch settings. This test is independent of any other equipment or software. Running the self test 1. Make sure the printer is turned off and the printer cover is closed properly. 2. While holding down the FEED button, turn on the printer using the switch on the front of the printer to begin the self-test.
RP-300-H User’s Manual 5. Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hex dump functions, the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands. To use the hex dump feature, follow these steps: 1. After you make sure that the printer is off and Dip s/w 1-2 is ON, turn on the printer. 2.
RP-300-H User’s Manual 6. Specifications Appendix A : Specifications 6-1. General Specifications (1) Printing Method Direct line thermal printing. (2) Print speed 200mm/sec. (3) Dot density 180 / 180 (0.142mm / 0.142mm dot) 180DPI(Hor/Ver) (4) Printing Width Max 72mm (512dots) 180DPI (5) Number of print columns. No. of columns Font “A” Font “B” 42 56 180DPI (6) Roll paper Refer to chapter 2 for details on the recommended roll Paper. Paper width : 50mm~82.5mm Roll diameter : Max.
RP-300-H User’s Manual 22
RP-300-H User’s Manual 6-2. Auto Cutter Specifications (1) Cutting Frequency Max. 30 cuts per minute (2) Thickness of paper 0.06 ~ 0.09 mm (3) Cutter Life 1.0 million cuttings (if the paper thickness is between 65 and100µm) 6-3. Interface RS232C Serial Interface, Centronics Parallel Interface(IEEE1284), USB Interface USB COMBO Interface, Ethernet Interface(10Mbps), Wi-fi(802.11b) 6-4. Electrical Characteristics (1) Input Voltage DC 24V ± 10% (2) Current Consumption Operating: Approx. 1.
RP-300-H User’s Manual ♠Important! When connecting or disconnecting the power supply from the printer, be sure that the following cautions are observed. (1) Use a power supply (Limited Power Supply) of DC 24V·10% and more than 2.5A. (2) Be careful about installin gthe printer in an area where there is noise. (3) Take the appropriate measure to protect against electrostatic AC line noise, etc. 6-5.
RP-300-H User’s Manual 7. Command List No.
RP-300-H User’s Manual No. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 1 2 3 4 5 6 7 8 9 10 11 26 Command ESC p ESC t ESC { FS p FS q GS ! GS $ GS * GS / GS B GS H GS I GS L GS P GS V GS W GSGନ GS a GS f GS h GS k GS r GS v 0 GS w < Add > ESC i ESC m FS ! FS & FS FS .
RP-300-H User’s Manual 27
RP-300-H User’s Manual ♣⊼ᛣџ䷙: ⿏䰸DIP switch㪟ᄤࠡ ䷜ܜᇛprinter䳏⑤䮰ᥝ ҹⷁ⫳ⱐܡ䏃ᇢ㟈printer➦↔. 1. ⺎ܜ䁡printer䳏⑤⺎ᆺ䮰䭝 2. ⿏䰸DIP switch㪟ᄤϞП㶎㍆ ݡᇛ㪟ᄤᠧ䭟 བ೪⼎ G 3.Փ⫼ᇪൟᎹ 䀁ᅮswitches, 䃌བ䩋ᄤᇣ㶎㍆䍋ᄤ 4.
RP-300-H User’s Manual ♣⊼ᛣџ䷙: ⭊߫ॄ㋭ߛࡆ䏇㛿वԣᰖ ৃ㛑ᰃ㹿Ϟッ㪟ᄤवԣ ℸ。⢔⊕ϟ 䂟䞡㻛ᇛ䳏⑤䭟 䮰ᭌ བᵰᬙ䱰ҡ⛵⊩ᥦ䰸 䂟ձᕾҹϟℹ倳ᥦ䰸ᬙ䱰 1. ⺎䁡printer䳏⑤⺎ᆺ䮰䭝 2.
Rev. 2.
