MF873-03 CMOS 4-BIT SINGLE CHIP MICROCOMPUTER S5U1C63000H1 Manual (S1C63 Family In-Circuit Emulator)
NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
The information of the product number change Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
CONTENTS CONTENTS CHAPTER 1 INTRODUCTION ____________________________________________ 1 CHAPTER 2 S5U1C63000H1 PACKAGE __________________________________ 2 2.1 2.2 2.3 2.4 2.5 CHAPTER 3 CONNECTION _____________________________________________ 7 3.1 3.2 3.3 3.4 CHAPTER General of Operation ................................................................................... 11 Break Function .............................................................................................
CONTENTS CHAPTER 8 TROUBLE SHOOTING ________________________________________ 21 CHAPTER 9 SPECIFICATIONS OF LCD63001 _______________________________ 22 9.1 Introduction .................................................................................................. 22 9.1.1 General description of LCD63001 ........................................................... 22 9.1.2 External view of LCD63001 ...................................................................... 22 9.2 Precautions on Using ..
CHAPTER 1: INTRODUCTION CHAPTER 1 INTRODUCTION S5U1C63000H1 (In-Circuit Emulator for S1C63 Family) is a hardware tool to effectively develop software for the S1C63 Family, 4-bit single chip microcomputers. In combination with the Peripheral Circuit Board (S5U1C63xxxP), it provides the development environment of the software using a personal computer as a host computer, which requires Windows Ver. 3.1 or later.
CHAPTER 2: S5U1C63000H1 PACKAGE CHAPTER 2 S5U1C63000H1 PACKAGE 2.1 Components This package is in common with all models of the S1C63 Family. After unpacking the S5U1C63000H1 package, check to see that all of the following components are included. Figure 2.1.1 shows the packing structure. (1) S5U1C63000H1 (main unit with LCD63001 board) .................................. 1 unit (2) RS232C cable (for IBM PC/AT) ....................................................................
CHAPTER 2: S5U1C63000H1 PACKAGE 2.2 Component Specifications Table 2.2.1 shows the specifications of the component in the S5U1C63000H1 package. Table 2.2.1 Specifications of S5U1C63000H1 components No. 1 2 3 4 Components Items Specifications Dimensions Weight 282 (W) × 177 (L) × 90 (H) Approx. 3.5 kg (main body) External color Cygnus white Input voltage DC 5 V Power consumption Board mounted 2 A, max.
CHAPTER 2: S5U1C63000H1 PACKAGE 2.4 Specifications of Operation Panels This section explains the operation of each switch. Figure 2.4.1 shows the external view of the panels. T OU OP ST O U T TR C BR IN K IN G N D TR G PO W ER SL EM P/ U H L PC T 1 PC 5 1 PC 4 1 PC 3 1 PC 2 1 PC 1 10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 PC 1 PC 0 12345678 ICE RS232C RUN ICE63 SEIKO EPSON CORP. (Front view) OFF ON POWER DC 5V (Rear view) (Front) (Rear) CB (Side view) Fig. 2.4.
CHAPTER 2: S5U1C63000H1 PACKAGE Table 2.4.1 shows the function of each component on the panels. Table 2.4.1 Function list of components No. 1 Position Side panel Indicated symbol CB Name Function Circuit breaker The breaker cuts off the power of S5U1C63000H1 system (ICE board, LCD board, PRC board and target board) at consumption current of 4 A or more. A small staff of the breaker comes up at the shut-off. The staff should be at the recessed position for normal operating status.
CHAPTER 2: S5U1C63000H1 PACKAGE 2.5 Setting the Dip Switch The S5U1C63000H1 works with a personal computer that runs MS-Windows Ver. 3.1 or later as a host. With a general computer that meets the condition, the serial transfer rate set at the factory (9600 bps) is good for use. In case the rate is changed, the transfer rate between the host computer can be changed by this switch. The switch also sets a self diagnostic function, which is equipped in the S5U1C63000H1, working or not working at the power on.
CHAPTER 3: CONNECTION CHAPTER 3 CONNECTION This chapter describes the connection between the S5U1C63000H1 and a host computer and the Peripheral Circuit Board (S5U1C63xxxP). 3.1 AC Cable The S5U1C63000H1 package includes a dedicated AC cable (3 poles type) and an AC adapter. The AC cable is connected into the AC inlet on the AC adapter. The common ground frame line should be used for connecting the S5U1C63000H1 and the host computer as shown in Figure 3.1.1.
CHAPTER 3: CONNECTION 3.4 Installing Peripheral Circuit Board (S5U1C63xxxP) By installing a Peripheral Circuir Board (to be separately sold) into a slot of the S5U1C63000H1, a debug system can be made corresponding to each device of the S1C63 Family. Figure 3.4.1 shows installing method of the Peripheral Circuir Board. The S5U1C63000H1 is equipped with a main control board and a LCD drive board. (1), (4) (2) Peripheral Circuit Board (2), (3) Fig. 3.4.
CHAPTER 4: GETTING STARTED CHAPTER 4 GETTING STARTED There are two operation modes in the S5U1C63000H1. One is ICE mode to be started with the debugger in connection with a host machine (the ICE/RUN switch on the front panel is set to ICE side) and the other one is free run mode to run a target program without a host machine (the ICE/RUN switch is set to RUN side). 4.
CHAPTER 4: GETTING STARTED ● Notes on free run mode (1) Any configuration information, various mask information and target program have not been written in the flash memory built into the S5U1C63000H1 at the time of ex-factory. Even though the S5U1C63000H1 enters in the free run mode without the data, it does not execute any target program and while the program counter on the front panel indicates the reset address of 110H.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 CHAPTER 5 OPERATION AND FUNCTION OF S5U1C63000H1 This chapter describes operations, functions in detail and restrictions in the emulation mode of the S5U1C63000H1. 5.1 General of Operation ICEcontrol processor Emulation control portion Emulation program memory RS-232C host interface Emulation data memory S1C63000 CPU Trace control portion Break control portion Target monitor portion To PRC board ICE firmware Flash memory Fig. 5.1.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 5.2 Break Function ● Forced break The debugger on the host machine can forced break the emulation. This function is useful when the program counter does not proceed by executing the SLP or HALT instruction in a single step process. ● Break commands Some break commands are available to set various breaking conditions. A break occurs when the break condition specified by the command and status of the S1C63000 CPU are met.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 ● TRCIN input terminal By connecting a signal line of the target system to this terminal, trace information is stored into the trace memory. "1" is written to the trace memory when it is not connected or the signal is at high level, and "0" is written to the trace memory when the signal is at low level. The signal is sampled at the rising edge of T4 state.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 5.6 Target Interrupt and Break When an interrupt in the target program and a break are simultaneously occurred, the target interrupt is prioritized. The break occurs after completing the stack operation of the interrupt. The program counter at the break shows the top address of the interrupt handler routine. When the target program is restarted, it executes from the top address of the interrupt handler routine.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 5.8 Trace Mode There are following three trace modes. (1) All bus cycle trace mode In this trace mode, all bus cycles are traced during run emulation and step emulation until a break occurs. (2) Specified PC range trace mode In this mode, bus cycles within the specified range (or outside the specified range) are traced during run emulation and step emulation until a break occurs.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 5.12 Self Diagnosis Function In the S5U1C63000H1, it is possible to select whether the self diagnosis at power on is executed or not. (1) No self diagnosis mode (DSW8: on, factory setting) When the DIP switch 8 on the front panel of the S5U1C63000H1 is set to on, the S5U1C63000H1 becomes ready to accept commands without the self diagnosis after power on.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 (2) Interrupt in standby mode In the standby mode, interrupt requests from the target system is reserved. The interrupt while the monitor program is being executed is accepted at the execution of the target program. For instance, when an interrupt request from the target system is generated while breaking, the interrupt is accepted immediately after the target program restarts if the interrupt is enabled in the S1C63000 CPU.
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H1 (7) Register (data) break The register (data) value after completion of the break operation may differ from the original setting register (data) condition for the break.
CHAPTER 6: NOTES ON USING CHAPTER 6 NOTES ON USING Pay attention to the following matters for proper use of the S5U1C63000H1. 6.1 Notes on Operations (1) Connection and disconnection between units Make sure that the S5U1C63000H1 and the personal computer are off when installing the Peripheral Circuir Board, connecting cables and disconnecting them. Specially, the connection of the target interface cable with the power on may make permanent destruction of IC’s inside due to its CMOS structure.
CHAPTER 7: MAINTENANCE AND WARRANTY CHAPTER 7 MAINTENANCE AND WARRANTY 7.1 Diagnosis Test The self diagnosis test is executed by setting SW8 of the DIP switch to OPEN and starting the debugger after power of the S5U1C63000H1 on. Debugger for E0C63 Ver x.xx Copyright(C) SEIKO EPSON CORP. 199x Connecting with ICE ............. DIAG test, please wait 5 min. .. done ← ➀ Parameter file name : xxxxxxxx.par Version : xx Chip name : xxxxx CPU version : x.x PRC board version : x.x LCD board version : x.
CHAPTER 8: TROUBLE SHOOTING CHAPTER 8 TROUBLE SHOOTING Following shows some hardware errors and their possible causes. ● A message of "connecting with ICE...failure" is displayed at the execution of the debugger (db63.exe).
CHAPTER 9: SPECIFICATIONS OF LCD63001 CHAPTER 9 SPECIFICATIONS OF LCD63001 9.1 Introduction 9.1.1 General description of LCD63001 The LCD63001 provides on a board the peripheral circuits (LCD driver) of the S1C63 Family microcomputers other than the core CPU. The board can work as an emulator corresponding to each model of the S1C63 Family by installing into the S5U1C63000H1 along with a S1C63 Family Peripheral Circuit Board (S5U1C63xxxP).
CHAPTER 9: SPECIFICATIONS OF LCD63001 9.2 Precautions on Using Follow the precautions described below to ensure that the LCD63001 board is used properly. Note, however, that some functions described here may not be available with some models. For details, refer to the technical hardware manual for each model. 9.2.1 Notes on operations Always be sure to power off all connected equipment before connecting or disconnecting the cable. 9.2.
CHAPTER 9: SPECIFICATIONS OF LCD63001 9.3 Connection with Target System Use the connection cables (100-pin/50-pin × 2 flat type, 34-pin flat type) supplied for the connection between the LCD63001 and target systems. mark I/O connection cable CN2-1 (50-pin) CN2-2 (50-pin) To target board CN3 (34-pin) To target board Fig. 9.3.
CHAPTER 9: SPECIFICATIONS OF LCD63001 ● Pin layout of connectors CN-2 connectors (100-pin/50-pin × 2 flat type) No. 1 CN2-1 connector Name Function COM0 COM0 No. 1 CN2-2 connector Name Function SEG42 SEG42 CN-3 connector (34-pin × 2 flat type) No.
CHAPTER 9: SPECIFICATIONS OF LCD63001 9.4 Product Specifications Following shows the specifications of the LCD63001 components. ● LCD63001 Dimension: Weight: Power supply: 254 mm (wide) × 144.8 mm (depth) × 13 mm (height) (including screws) Approx.
International Sales Operations AMERICA ASIA EPSON ELECTRONICS AMERICA, INC. EPSON (CHINA) CO., LTD. - HEADQUARTERS - 28F, Beijing Silver Tower 2# North RD DongSanHuan ChaoYang District, Beijing, CHINA Phone: 64106655 Fax: 64107319 1960 E. Grand Avenue EI Segundo, CA 90245, U.S.A. Phone: +1-310-955-5300 Fax: +1-310-955-5400 SHANGHAI BRANCH 4F, Bldg., 27, No.
In pursuit of “Saving” Technology, Epson electronic devices. Our lineup of semiconductors, liquid crystal displays and quartz devices assists in creating the products of our customers’ dreams. Epson IS energy savings.
S5U1C63000H1 Manual (S1C63 Family In-Circuit Emulator) ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epson.co.
