EPSON® USB/Parallel Adapter User’s Guide for the EPSON Stylus COLOR 440, EPSON Stylus COLOR 640, EPSON Stylus COLOR 600 and EPSON Stylus Photo EX IMPORTANT: To use the USB/Parallel Adapter with your Apple® iMac™, you must download and install the iMac Update 1.0 from Apple at http://swupdates.info.apple.com.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. Copyright © 1998 by Epson America, Inc.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces.
Contents Introduction Setting Up the Printer Getting Started on an iMac Connecting the Cable Installing the Printer Software Getting Started on a Windows 98 System Connecting the Cable Installing the Printer Software Setting Up Your System to Print to the EPSON Stylus COLOR 600 Appendix A: Using Monitor3 with Your iMac Setting Up Monitor3 Monitoring Print Jobs with Monitor3 Appendix B: Specifications USB/Parallel Adapter Specifications System Requirements v 7 8 8 10 13 15 16 19 27 29 29 30 33 33 34
Introduction The EPSON USB/Parallel Adapter allows you to use smart cable technology to connect your EPSON printer to your Apple iMac or Windows® 98 computer. It supports the following printers: EPSON Stylus® COLOR 600, EPSON Stylus COLOR 440, EPSON Stylus COLOR 640, and EPSON Stylus Photo EX. To use the EPSON USB/Parallel Adapter with your computer and EPSON printer, you’ll need to: ◗ Install iMac Update 1.
Setting Up the Printer If you’ve been using your EPSON printer with your computer, the printer is probably set up already. If so, turn it off and disconnect it from the previous computer. Then go to the section explaining how to connect the cable to your system. If you’re setting up a new printer, see the documentation that came with your printer for instructions on unpacking, installing ink cartridges, and loading paper.
For instructions on using the printer software, see the following: ◗ If you have an EPSON Stylus COLOR 440 or EPSON Stylus COLOR 640, locate the electronic EPSON Stylus COLOR 440/640 Driver Software Guide for Macintosh in the Manual directory on your USB Printer Software CD-ROM. Copy the manual to your hard drive and view it using Adobe® Acrobat Reader 3.01. (If you don’t have Acrobat Reader on your computer, you can install it using the Acrobat Reader 3.01 Installer on your USB Printer Software CD-ROM.
Connecting the Cable You can connect the USB/Parallel Adapter directly to a USB port on your iMac or to a USB hub connected to a port on the iMac. If you have any printing problems when the printer is connected via a USB hub, try connecting the printer directly to the USB port on the iMac instead. 1 To connect the adapter to the USB port on the side of the iMac, first open the port door. Hold the adapter’s USB connector so the icon faces up and connect it to the available USB port.
To connect the adapter to one of the USB ports on the iMac keyboard, hold the adapter’s USB connector so the icon faces away from you and connect it to the USB port. available USB port optional USB hub OR USB/Parallel adapter If you’re using a USB hub, plug it into the USB port on the iMac keyboard, then connect the adapter to an available USB port on the hub.
2 Connect the adapter’s parallel connector to the parallel port on the back of the printer, then secure it with the wire clips. parallel connector 3 Now follow the instructions in the next section to install the printer driver software from the USB/Parallel Adapter CD-ROM.
Installing the Printer Software IMPORTANT: You can’t use the adapter with the printer driver software that came with your printer. You must use the printer driver software that came on the USB Printer Software CD-ROM. Before you begin this procedure, you must install the iMac Update 1.0 from Apple at http://swupdates.info.apple.com. Contact Apple Computer if you have any problems installing this update.
8 Click the printer icon for your printer. Note: The printer icons are labeled SC 600 (EPSON Stylus COLOR 600), SC 440 (EPSON Stylus COLOR 440), SC 640 (EPSON Stylus COLOR 640), and SPEX (EPSON Stylus Photo EX.) 9 Click the USB Port icon (if you’ve connected more than one EPSON printer, the port is numbered). 10 Turn on background printing, if you want to use it. Then close the Chooser.
Getting Started on a Windows 98 System The instructions on the next few pages explain how to connect the USB/ Parallel Adapter cable to your Windows 98 system and how to install the printer software. If you’re connecting to an EPSON Stylus COLOR 600 printer, you’ll also find instructions on how to set up your system to use Windows Print Manager. For instructions on using the printer software, see the documentation that came with your printer.
Connecting the Cable You can connect the USB/Parallel Adapter directly to a USB port on your computer, or you can connect it to a USB hub connected to a port on your computer. If you have any printing problems when the printer is connected via a USB hub, try connecting your printer directly to the USB port on the computer instead. 1 Locate an available USB port on your computer (your USB ports may be in a different location than shown in the illustration on page 17).
OR optional USB hub 17 USB/Parallel adapter
3 Connect the adapter’s parallel connector to the parallel port on the back of the printer, then secure it with the wire clips. parallel connector 4 Now follow the instructions in the next section to install the printer driver software.
Installing the Printer Software The steps you follow to install the USB printer driver software depend on whether you’ve already installed a printer driver for your printer, or whether you’re performing a new installation. If you’ve already installed a printer driver, follow the steps below. If not, follow the steps on page 24. Note: The USB printer driver software works best with a Windows 98 system that has not been upgraded from Windows 95.
4 Click the View tab. Under Hidden files, select Show all files. Click Apply to save the setting, then click OK to close the Folder Options dialog box. 5 Open the Inf folder, then locate and select the INF file corresponding to your installed printer driver: EPSONEPIIFE2J.INF EPSONEPS600.INF EPSONEPIIFE3P.INF EPSONEPIIFE3O.INF EPSON Stylus Photo EX EPSON Stylus COLOR 600 EPSON Stylus COLOR 440 EPSON Stylus COLOR 640 6 Click Delete to delete the old printer driver. Close Windows Explorer.
4 Select Specify a location, then click Browse to locate the USB printer software. The software is located in the following folders on the CD-ROM: Stylus Photo EX, Stylus COLOR 600, Stylus COLOR 440, and Stylus COLOR 640.
5 Click Next. The Add New Hardware Wizard now displays EPSON USB Conversion Cable. 6 Click Next. The installer copies the USB printer files to your system. At the final screen, click Finish.
Windows 98 detects your printer and displays a screen similar to the following: 7 Click Next to install your printer driver. At the next screen, select Search for the best driver for your device and click Next. 8 Follow the on-screen instructions to install your printer driver. Be sure to click the Yes radio button to set your printer as the Windows default printer. At the last screen, click Finish. 9 When you see a message that installation is complete, click OK.
If you’re performing a new installation Don’t install the printer driver software that came with your printer. You can’t use this driver software with your USB/Parallel adapter. However, you can use the USB printer software to connect the printer to your computer via the parallel port, if you want. Note: If you install the printer driver software by mistake, see page 19 for instructions on deleting the driver’s INF file.
2 Follow the instructions to begin installation of your printer software. When you see a screen similar to the following, click Cancel to cancel printer driver installation. 3 Continue with the instructions to install your creative software applications. Note: The installer for the EPSON Stylus Photo EX installs the creative software before it installs the printer driver software. 4 When you’ve finished installing the creative software, restart your system. 5 Remove your printer driver CD-ROM.
Checking your installation To verify that your USB software installed properly, check the Device Manager. Click Start, point to Settings, and click Control Panel. Then click System and click the Device Manager tab. You should see the device EPSON USB Conversion Cable Devices listed. Click the + next to the device; you should see EPSON USB Conversion Cable (EPXUSB1:) listed too.
Setting Up Your System to Print to the EPSON Stylus COLOR 600 The EPSON Stylus COLOR 600 printer driver software requires that you use the Windows Print Manager when printing to the USB/Parallel Adapter. Follow these steps to enable the Windows Print Manager: 1 Click Start, point to Programs, Epson, and select Spool Manager4. 2 In the EPSON Spool Manager window, select the EPSON Stylus COLOR 600 icon. 3 From the Queue menu, select Setup. The Queue Setup dialog box appears.
4 Select Use Print Manager, then click OK to close the Queue Setup dialog box. 5 Close the Spool Manager window.
Appendix A: Using Monitor3 with Your iMac The Monitor3 utility lets you continue to work on your iMac while your document is printing (though printing and processing may be slower). The Monitor3 dialog box lets you check on your print jobs and cancel, pause, or restart them. See the next section to turn on background printing and increase the memory allocation for Monitor3. Setting Up Monitor3 1 Open the Chooser from the Apple menu and select the icon for your printer (SC 600, SC 440, SC 640, or SPEX).
Monitoring Print Jobs with Monitor3 While you’re printing, click the EPSON Monitor3 icon on the Application menu at the right end of the menu bar.
To set priorities for jobs waiting to print, click the job, then click the Show details arrow at the bottom of the window. Priority list box Settings selected for the highlighted print job Note: If you see a stop sign icon and the message “Print queue on hold” in the EPSON Monitor3 dialog box, select Start print queue from the Printer menu to release the queue and resume printing.
The Priority list becomes active. Click the arrow and select one of the following settings: ◗ Normal prints the job in the order it is received ◗ Urgent moves the job before any Normal priority jobs in the print queue ◗ Hold holds the job in the print queue until you’re ready to release it for printing by clicking the restart icon ◗ Print Time opens this dialog box so you can set a specific day and time for printing.
Appendix B: Specifications USB/Parallel Adapter Specifications USB connector: USB series A; compliant with USB Specification Revision 1.0 Parallel connector: IEEE-1284-B; Compatibility, Nibble, and ECP mode supported Cable: 2-meter, 5-conductor, insulated, shielded, USB compliant Temperature: Operating: Non-operating: Storage: Operating humidity: 32 to 158 °F (0 to 70 °C) –4 to 212 °F (–20 to 100 °C) –67 to 257 °F (–55 to 125 °C) 10 to 80% relative humidity, no condensation Input voltage: 4.
System Requirements Macintosh Computer: Apple iMac Operating system: Macintosh OS 8.1 with iMac Update 1.
Windows Computer: An IBM® compatible PC with at least a 486/ 66 MHZ processor (Pentium® processor recommended) Operating system: Windows 98 Memory: At least 16MB of RAM (32MB recommended) Storage: At least 50MB or free hard disk space for storing images (100MB recommended) Display: VGA, Super VGA, or better display adapter and monitor CD-ROM drive: Double-speed CD-ROM drive (quad-speed or faster recommended) for installing the printer software Printer cable: EPSON USB/Parallel Adapter cable 35
36