User’s Guide NPD4829-01 EN
SC-F7000 Series User’s Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers.
SC-F7000 Series User’s Guide Contents Contents Saving Optimal Settings for the Current Media (Print Media Settings). . . . . . . . . . . . . . . . . . . . . Parameters Stored in Media Setting Banks. . . . Saving Settings. . . . . . . . . . . . . . . . . . . . . . . . Correcting Print Misalignment (Head Alignment). . . . . . . . . . . . . . . . . . . . . . . . . . . . . Feed Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . Using a Test Pattern. . . . . . . . . . . . . . . . . . . .
SC-F7000 Series User’s Guide Contents When a Maintenance Call/Service Call Occurs. . . Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . You cannot print (because the printer does not work). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The printer sounds like it is printing, but nothing prints. . . . . . . . . . . . . . . . . . . . . . . . . The prints are not what you expected. . . . . . . . Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Others. . . . . .
SC-F7000 Series User’s Guide Introduction ❏ Use only the power cord that comes with this product. Use of another cord may result in fire or electric shock. Introduction ❏ Do not use a damaged or frayed power cord. Important Safety Instructions ❏ If you use an extension cord with this product, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating.
SC-F7000 Series User’s Guide Introduction ❏ This device has two power systems. There is a risk of electric shock unless the two power cables are unplugged during the maintenance. Illustrations The illustrations in this manual may differ slightly from the actual objects they are intended to represent. When handling the ink packs Operating System Versions ❏ Keep ink packs out of the reach of children and do not drink. In this documentation, the following abbreviations are used.
SC-F7000 Series User’s Guide Introduction Printer Parts Front A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Around the Print Head” on page 54 B Eject guide Media is ejected along this guide. C Roll core holder Place the used roll core for media take-up on these holders. There are two holders: one on the left and one on the right.
SC-F7000 Series User’s Guide Introduction F Roll support Rest media temporarily on these supports when removing the take-up roll. There are two supports: one on the left and one on the right. G Auto switch Use this switch to select the auto take-up direction. Choose Off to disable auto take-up. H Manual switch Use this switch to select the manual take-up direction. The selected option takes effect when the Auto switch is in the Off position. I Casters There are two casters on each leg.
SC-F7000 Series User’s Guide Introduction U Maintenance cover (right) Open this cover to perform maintenance around the print head. Normally closed when using the printer. U “Maintenance Around the Print Head” on page 53 V Media loading lever After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media prior to removal. W Alert lamp This lamp lights or flashes when an error occurs.
SC-F7000 Series User’s Guide Introduction Slider LAN port A Slider Attach the chip unit included with the ink pack before refilling the ink. U “Chip Unit Replacement and Ink Refills” on page 61 A RJ-45 connector Connects the LAN cable. Use a shielded twisted pair cable (category 5 or higher). B Ink inlet cover Open this cover to refill the ink tank with ink. B Data lamp (orange) Indicates the network connection status and data receive status by flashing and/or turning on.
SC-F7000 Series User’s Guide Introduction Inside Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. A Print head The print head prints by moving left and right while emitting ink. Cleaning may be required depending on the status.
SC-F7000 Series User’s Guide Introduction F Wiper cleaner The wiper cleaner removes ink from the wiper. It is a consumable; replacement may be required depending on the status. U “Replacing the Wiper and Wiper Cleaner” on page 59 G Caps Except during printing, these caps cover the print head nozzles to prevent them drying out. Cleaning may be required depending on the status. U “How to Clean” on page 53 H Wiper The wiper removes ink from the print head nozzles.
SC-F7000 Series User’s Guide Introduction D Lift lever If the media to be mounted on the roll holders seems heavy, use these levers to raise the media effortlessly to the level of the roll holders. There are two lift levers: one on the left and one on the right. E Loading guide Media is loaded along this guide. F Roll support Rest media on these supports before placing it on the roll holders. There are two supports: one on the left and one on the right.
SC-F7000 Series User’s Guide Introduction D Display Displays the printer’s status, menus, error messages, and so on. U “Understanding the Display” on page 15 Control panel E Menu button Press this button to display menus. U “Using the Control Panel Menu” on page 66 F y button (back button) Press this button to exit to the previous menu when options are displayed.
SC-F7000 Series User’s Guide Introduction Pressing this button displays the Maintenance menu, which contains such items as Nozzle Check, Cleaning, Head Maintenance, and Waste Ink Counter. This button is disabled during printing. U “The Maintenance Menu” on page 75 ❏ If a media setting bank number created with this printer is selected as the print media, the number (from 1 to 30) will be displayed. When RIP Settings is selected, 0 will be displayed. ❏ The selected platen gap is shown as follows. : 1.
SC-F7000 Series User’s Guide Introduction BK : Black Y : Yellow M : Magenta C : Cyan Features This wide-format color ink jet printer supports roll media 1626 mm (64 inches) in width. The main features of this printer are described below. Realizing High Productivity D Waste ink bottle status Displays the approximate amount of space available in the waste ink bottle. The display changes as shown below when the waste ink bottle is nearly full or an error occurs.
SC-F7000 Series User’s Guide Introduction E-Mail Error/Warning Notification The EpsonNet Config with Web Browser system built into the printer’s network interface offers e-mail notification. Once configured for e-mail notification, the printer will send errors and warnings to selected e-mail addresses, ensuring peace of mind when the printer is left unmanned during overnight operation and in other similar situations.
SC-F7000 Series User’s Guide Introduction ❏ Do not bend or tug the waste ink tube. Ink could spill inside or around the printer. ❏ As well as being expended during printing, ink is used during head cleaning and other maintenance required to keep the print head in working order. ❏ We recommend performing maintenance on the following components as required. Failure to perform appropriate maintenance will shorten print head life.
SC-F7000 Series User’s Guide Introduction ❏ Close all covers before placing the printer in storage. If you are not using the printer for a long time, put an anti-static cloth or cover on the printer to prevent dust. The print head nozzles are very small, and they can become clogged easily if fine dust gets on the print head, and you may not be able to print properly. Handling Media Note the following when handling or storing media. Media that are in poor condition will not produce good quality prints.
SC-F7000 Series User’s Guide Introduction ❏ To prevent discoloration, display and store prints as instructed in the documentation supplied with the media.
SC-F7000 Series User’s Guide Introduction Using the Supplied Software Contents of the Software Disc The following applications are available on the supplied software disc. Install as required. For information about these applications, see the Network Guide (pdf) or the on-line help for the application in question. Note: ❏ The supplied disc does not contain printer drivers. A software RIP is required for printing.
SC-F7000 Series User’s Guide Introduction Uninstalling Software Starting EPSON LFP Remote Panel 2 c ❏Important: Log in to an “Computer administrator” Launch EPSON LFP Remote Panel 2 after confirming that the printer displays Ready. A The application can be launched using either of the following two methods. ❏ ❏ B account (an account with administrators privileges). Double-click the EPSON LFP Remote Panel 2 icon on the desktop.
SC-F7000 Series User’s Guide Basic Operations When the Standard Media Feeding Unit Is Installed Basic Operations This section describes how to load media when the standard media feeding unit is installed. Loading and Exchanging Media !Caution: Because the media is heavy, it should not be carried by one person. When loading or removing the media, use at least two persons.
SC-F7000 Series User’s Guide Basic Operations C D Place media on the roll support oriented according to how it is rolled (see below) and position it as indicated by the mark on the label. Raise the lift lever on the left side of the printer to lift the media into position, then firmly insert the roll holder. If the roll of media has the outer diameter which is less than 140 mm, lift it up by your hands, and set it to the roll holder.
SC-F7000 Series User’s Guide Basic Operations F H Raise the lift lever on the right side of the printer to lift the media into position, then firmly insert the roll holder. Rotate the handle until part A in the illustration below is fully inserted. If the roll of media has the outer diameter which is less than 140 mm, lift it up by your hands, and set it to the roll holder as described in Step 4.
SC-F7000 Series User’s Guide Basic Operations Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. L Go to the front of the printer and open the front cover. M Hold the center of the media and raise the media loading lever. N Pull the media straight forward until the edge has past the label on the bottom side of the eject guide.
SC-F7000 Series User’s Guide Basic Operations P For information on loading the media into the auto take-up reel unit, see: U “Using the Auto Take-up Reel Unit” on page 35 Attach the media holding plates at either side of the media. First, position the plates so that the edges of the media are in the centers of the round holes. Next, adjust the position until the white line is visible in the square window and push the plates down to lock them in place and keep them from lifting.
SC-F7000 Series User’s Guide Basic Operations c ❏Important: Do not use the media holding plates with media that is more than 0.4 mm thick. The media holding plates could touch and damage the print head. Q ❏ Move the media holding plates to the left and right edges of the platen when they are not in use. ❏ Do not use the media holding plates if the sides of the printed media are smudged or torn. ❏ Leave left and right margins of over 10 mm when using the media holding plates.
SC-F7000 Series User’s Guide Basic Operations Printable Side In If the label does not have the loading position, mark it on the label as instructed in the Setup Guide supplied with the optional heavy roll media system. D Align the media and the roll holders. E Fully insert the left roll holder. Next, tighten the roll holder screw to fix the roll holder in place. F Fully insert the right roll holder. Next, tighten the roll holder screw to fix the roll holder in place. G Remove the lifter.
SC-F7000 Series User’s Guide Basic Operations H J Rotate the handle until part A in the illustration below is fully inserted. Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In Important: c Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder.
SC-F7000 Series User’s Guide Basic Operations N Pull the media straight forward until the edge has past the label on the bottom side of the eject guide. Keep the right edge of the media parallel with the scale markings on the two labels on the eject guide. L Go to the front of the printer and open the front cover. M Hold the center of the media and raise the media loading lever. O Lower the media loading lever to hold the media in place. To print immediately, proceed to Step 16.
SC-F7000 Series User’s Guide Basic Operations c ❏Important: Do not use the media holding plates with Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the media slightly. P media that is more than 0.4 mm thick. The media holding plates could touch and damage the print head. Be sure, however, to stop rewinding before the leading edge of the media is past the cutter groove (on the pressure roller side).
SC-F7000 Series User’s Guide Basic Operations ❏ Remaining Setup A On: The printer displays the amount of media remaining. Off: The printer does not display the amount of media remaining. Select an option. To print at current settings: Use the d/u buttons to select Keep Settings Above and press the Z button. Proceed to Step 6.
SC-F7000 Series User’s Guide Basic Operations You can print the amount of media remaining on the leading edge of the roll before it is removed from the printer and then enter this number the next time the media is loaded for accurate information on the amount remaining. !Caution: When cutting media, be careful not to cut your fingers or hands with the cutter or other blades.
SC-F7000 Series User’s Guide Basic Operations C Removing Media Remove the media holding plates. You can now remove the media from the roll holders. To remove the media, reverse the steps you followed to load it. Using the Auto Take-up Reel Unit Media Loading and Take Up D The auto take-up reel unit automatically takes up media as it is printed, improving the efficiency of unmanned operation. Cut the media with the cutter. Pass the blade of the cutter down the cutting groove.
SC-F7000 Series User’s Guide Basic Operations !Caution: ❏ Be sure that your hands or hair do not get C Align the right roll core holder with the right edge of the media and tighten the locking screw. D Insert the roll core onto the right holder. E Insert the left holder into the roll core. caught in the auto take-up reel unit while it is in operation. Failure to observe this precaution could result in injury.
SC-F7000 Series User’s Guide Basic Operations Important: c Stop when part A is no longer visible. The take-up reel unit may not function as expected if the holder is inserted too far. F Tighten the roll core holder locking screw to fix the roll core holder in place. B Press the d button in the control panel to feed enough media for a single wrap around the roll core. C Flip the Auto switch to Off and press the Manual to wrap the media once around switch to the roll core.
SC-F7000 Series User’s Guide Basic Operations D Flip the Auto switch to F . Confirm that the media is attached without deformation. As shown in the identified sections in the illustration below, if the tensions of the left and right edges of the media are different, the media cannot be taken up correctly. If there is slack on one side, repeat from Step 1. Note: As shown in the illustration below, you can confirm differences in tension by lightly tapping on both edges of the media.
SC-F7000 Series User’s Guide Basic Operations When attaching on the left and right, attach using tape while pulling the media straight down. Important: c Confirm that edges of media taken up on the roll core are not misaligned. If the edges are misaligned, the media that follows cannot be taken up correctly. When the edges are misaligned, press the Manual switch to the side, rewind the media, remove the tape, and then repeat from Step 1.
SC-F7000 Series User’s Guide Basic Operations E G Lower the tensioner. Press the d button to feed the media until the take up roll core begins to turn. Important: c The auto take-up reel unit will not function if the tensioner is raised. Removing the Take-up Roll The procedure for removing media varies depending on whether you are using the installed auto take-up reel unit or the optional auto take-up reel unit for heavy media. F Confirm that the media is attached without deformation.
SC-F7000 Series User’s Guide Basic Operations C Loosen the left roll core holder locking screw and remove the roll core holder from the roll. G D Lower the roll onto the roll support. Using the Optional Heavy Roll Auto Take-up Reel Unit Lower the roll onto the roll support. This section explains how to remove media from the take-up reel using a lifter. The following types of lifter can be used. ❏ Fork or platform thickness: 28 mm or less ❏ Fork or platform can be lowered to approx.
SC-F7000 Series User’s Guide Basic Operations B Perform head cleaning if parts of the pattern are faint or missing. Insert the lifter between the media and the auto take-up reel unit and adjust the height to support the take-up roll.
SC-F7000 Series User’s Guide Basic Operations ❏ Feed Speed Setting Name Name the media setting bank. Using distinctive names makes it easier to select banks for use. For more information on these items, see U “The Media Setup Menu” on page 70. Saving Settings Follow the steps below to save media settings. A Select Setting Name and press the Z button. B Use the d/u buttons to display letters and symbols. When the desired character is displayed, press the r button to select the next entry position.
SC-F7000 Series User’s Guide Basic Operations D Head Alignment Select Head Alignment to realign the print head when print results seem grainy or out of focus. Press the y button to return to the customize settings menu. Head Movement For Head Alignment, you need to check the pattern and enter the optimum adjustment value for alignment. Choose the range in which the print head moves during printing.
SC-F7000 Series User’s Guide Basic Operations D Tension Measurement Periodically is recommended in most circumstances. Choose Off if slack develops in the media or other printing problems occur. A Use the d/u buttons to select Tension Measurement and press the Z button. B Use the d/u buttons to select the desired setting and press the Z button. C Select the desired option and press the Z button. Exiting the Menus Press W to exit the menus.
SC-F7000 Series User’s Guide Basic Operations D Use the d/u buttons to select a media setting bank number between 1 and 30 and then press the Z button. I When C1 is displayed in the control panel, use the d/u buttons to select the number recorded in Step 8 and press the Z button. Note that any settings already saved in the printer will be overwritten. J Select the numbers for all colors and press Z. E Use the d/u buttons to select Head Alignment and press the Z button.
SC-F7000 Series User’s Guide Basic Operations Using a Test Pattern H The printer will print a test pattern. I Measure the distance between the “+” symbols. J Pattern length is displayed in the control panel. Using the d/u buttons, enter the value recorded in Step 10 and press the Z button. Buttons that are used in the following settings A After confirming that the printer is ready, press the Menu button. The settings menu will be displayed. B Select Media Setup and press the Z button.
SC-F7000 Series User’s Guide Basic Operations Printable area Performing Feed Adjustment During Printing The gray area in the illustration below shows the printable area. The arrow indicates the feed direction. Buttons that are used in the following settings The positions of items A to B are as follows: A (right edge of media) Varies with the option selected for Media Size Check. On selected for Media Size Check: The right edge of the media.
SC-F7000 Series User’s Guide Basic Operations 300-1626mm 3-25mm*1 3-825mm*2 5mm 5mm B A 1 The value selected for Side Margin(Left) in the setup menu. The default value is 5 mm. Choose a Side Margin(Left) over 10 mm when using media holding plates. 2 The total of the values selected for Print Start Position and Side Margin(Right) in the setup menu. The default value is 5 mm. Choose a Print Start Position or Side Margin(Right) over 10 mm when using media holding plates.
SC-F7000 Series User’s Guide Maintenance Maintenance E Clean the pressure rollers. F Clean the media holding plates and platen. Remove particles of paper and dust from the pressure rollers using a soft-bristled brush. Daily Maintenance To maintain print quality, perform the following inspection and cleaning before starting work each day. Cleaning the Platen, Pressure Rollers, and Media Holding Plates !Caution: Be careful not to trap your hands or fingers when opening or closing the front cover.
SC-F7000 Series User’s Guide Maintenance Checking for clogged nozzles B Select Nozzle Check and press the Z button. We recommend that you check the nozzles for clogs each time you print to ensure quality results. C A nozzle pattern will be printed. Ways to Check for Clogs There are two ways to check for clogs. When printing is complete, the media will automatically be fed to a position where the pattern is clearly visible. ❏ Print Nozzle Pattern Cut the media if necessary.
SC-F7000 Series User’s Guide Maintenance There is no need to clean the head if the print result does not contain faint areas or other color problems. Buttons that are used in the following settings You can also clean the head while printing is paused. Note, however, that hues in the printout may change when printing is resumed. Head Cleaning Level Choose from three levels of head cleaning. Select Execute (Light) first.
SC-F7000 Series User’s Guide Maintenance F ❏ A clean room wiper (available in the market) Head cleaning will be performed. A lint-free (non-woven) cleaning cloth. Use to clean around the print head. The menu will close when cleaning is complete. Print a nozzle pattern and inspect the results to determine whether the problem has been resolved.
SC-F7000 Series User’s Guide Maintenance D Clean the parts in the following order. Open the maintenance covers at each end. (1) Print head (2) Wiper (3) Caps (4) Wiper rail Cleaning Around the Print Head Moving the Print Head Inspect the area around the print head and remove any ink stains as described below. This section describes how to position the print head for part cleaning. A c BeImportant: sure to follow the steps below when positioning the print head.
SC-F7000 Series User’s Guide Maintenance B If there is ink on the attachment points, remove the wiper for cleaning. Proceed to Step 2. Ink spatters on the base of the print head can be removed using a clean room wiper (available in the market). c ❏Important: Be sure not to touch the nozzle surface during cleaning. Failure to observe this precaution could damage the print head. ❏ The parts shown below are sensors. Be careful not to touch this area with your hands or clean room wiper.
SC-F7000 Series User’s Guide Maintenance C Clean the front and back of the wiper with a cleaning stick. D Clean the bottom of the wiper with a cleaning stick. F Return the wiper when cleaning is complete. G Clean the area around the outside of the caps with a cleaning stick. Place on the attachment point and press down until you hear a click. Important: c Do not touch the insides of the caps. Failure to observe this precaution could deform the affected parts.
SC-F7000 Series User’s Guide Maintenance A B D When Press Z after cleaning. is displayed on the control panel and the Z button is pressed, the wiper moves to the back. Return the wiper cleaner that was removed in Step 2 to its original position. Place on the attachment point and press down until you hear a click. Remove the wiper cleaner. Grasp the cleaner as shown and lift it from the printer. E Close both maintenance covers and press the Z button.
SC-F7000 Series User’s Guide Maintenance Replacing the Waste Ink Bottle !Caution: ❏ Store waste ink in a location out of reach of children. ❏ Wear protective eyewear and gloves when replacing waste ink bottle. A Remove the waste ink bottle from the waste ink bottle holder. B Insert the waste ink tube into the mouth of the new waste ink bottle and place the waste ink bottle in the holder.
SC-F7000 Series User’s Guide Maintenance C Press the Z button. D Check again to confirm that a fresh waste ink bottle is correctly placed and then press the Z button to reset the waste ink counter. E Remove the wiper cleaner. F Insert a new wiper cleaner. Grasp the cleaner as shown and lift it from the printer. Replacing the Wiper and Wiper Cleaner Replace the wiper cleaner and wiper if the printout is faint or smudged, or segments are missing even after cleaning.
SC-F7000 Series User’s Guide Maintenance G Remove the wiper. H Insert new wiper. K Holding the wiper by the attachment point, tilt it left and lift it out. Remove the cap on the wiping part of the wiper. Place on the attachment point and press down until you hear a click. I Press the Z button when the replacement procedure is complete. J Close the maintenance cover and press the Z button. 60 The menus will close when the print head returns to its normal position.
SC-F7000 Series User’s Guide Maintenance Chip Unit Replacement and Ink Refills !Caution: ❏ Store ink packs in a location out of reach of children. ❏ Time Period for Chip Unit Replacements and Ink Refills Wear protective eyewear and gloves when refilling ink. Be sure to read the Material Safety Data Sheet (MSDS) before using ink packs. You can download it at your local Epson Web site. If the message Chip unit expended.
SC-F7000 Series User’s Guide Maintenance A If the message Chip unit expended. is displayed on the control panel screen, check the remaining ink in the ink tank via the scale on the ink pack. B Lift the lock lever for the slider of the chip unit you intend to replace. C Insert a finger into the depression on the top of the slider and pull straight outward.
SC-F7000 Series User’s Guide Maintenance E Attach the chip unit supplied with the new ink pack to the slider. G Shake the new ink pack as shown in the illustration horizontally for approximately 5 cm left and right for 5 seconds approximately 15 times. H Open the slider ink inlet cover. I Remove the ink inlet cap from the ink tank. Check to confirm that the color of the label on the slider matches the color of the label on the chip unit when installing.
SC-F7000 Series User’s Guide Maintenance J Tear off the ink pack spout opening. Important: c Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink tanks. This can cause messages from the remaining ink warning system to not be displayed properly. K L Put the ink inlet cap back on the ink tank. M Close the slider ink inlet cover. Fill the ink tank with the ink from the ink pack.
SC-F7000 Series User’s Guide Maintenance Parts That Are Periodically Replaced The following parts require periodic replacement. The time until the following parts need to be replaced depends on the conditions of use. ❏ Print head ❏ Carriage encoder ❏ Ink holder ❏ Damper kit ❏ Pump cap ❏ Ink supply tank The part life varies with operating conditions. Base the decision to replace the print head on the quality of the print results.
SC-F7000 Series User’s Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The menus are used as shown below.
SC-F7000 Series User’s Guide Using the Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Menu Item Media Setup Media Remaining U “The Media Setup Menu” on page 70 Parameter Remaining Setup On, Off Length 5.0 to 999.
SC-F7000 Series User’s Guide Using the Control Panel Menu Menu Item Parameter Drying Drying Time Per Pass Printer Setup U “Printer Setup Menu” on page 73 0 to 10 sec Media Suction 0 to 10 Head Movement Data Width, Printer Full Width Multi-Strike Printing Off, 2 to 8 Roll Type Printable Side Out, Printable Side In Tension Measurement Periodically, Every Page, Off Media Tension 0 to 40 Feed Speed 1 to 2 Print Media List Print Side Margin(Right) 3 to 25 mm (0.12 to 1.
SC-F7000 Series User’s Guide Using the Control Panel Menu Menu Item Parameter Print Logs Print Job Log Sheet Print Show Total Prints XXXXXX m2 (XXXXXX ft2) Print Status Sheet Print Firmware Version XXXXXXX,X_XX,XXXX U “The Print Logs Menu” on page 75 Printer Status U “The Printer Status Menu” on page 76 Network Setup U “The Network Setup Menu” on page 76 IP Address Setting Auto - Panel IP: 000.000.000.000 – 255.255.255.255 SM: 000.000.000.000 – 255.255.255.255 DG: 000.000.000.000 – 255.
SC-F7000 Series User’s Guide Using the Control Panel Menu Details of the Menu The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button. indicates default settings. Media Remaining Item Parameter Explanation Remaining Setup On Off Choose On to display and record, or Off to not display and not record, the amount of media remaining. Length, Remaining Alert, and Print Remaining Length options are available when On is selected.
SC-F7000 Series User’s Guide Using the Control Panel Menu RIP Settings Item Parameter Explanation Platen Gap 1.5 Change Platen Gap (the gap between the print head and the media) for the media setting bank selected in the software RIP. 2.0 2.5 The default setting of 1.5 is recommended in most situations. Choose 2.0 if printout is scratched or smudged. Select 2.5 only if print results are still smudged when 2.0 is selected.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Feed Adjustment Manual Use this option if banding (horizontal banding, lines, or strips of uneven color) persists after head cleaning and head alignment have been performed. Visually inspects the printed pattern and enter the adjustment value by hand. U “Feed Adjustment” on page 46 Platen Gap 1.5 2.0 2.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Tension Measurement Periodically Every Page Choose Periodically or Every Page to have the printer automatically monitor and adjust media tension during printing for optimal results, Off to disable automatic tension adjustment. Off Periodically is recommended in most circumstances.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Print Start Position 0 to 800 mm (0.00 to 32.00 inch) Adjust this parameter if you want to print from the near center of the media or if you want to shift the printed area left from the Side Margin(Right) setting. The area between the right edge of the media and Print Start Position is left blank.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Sleep Mode 15 to 240 minutes The printer will enter sleep mode if no errors have occurred, no print jobs have been received, and no actions are performed on the control panel for an extended period of time. This setting selects the amount of time until the printer enters sleep mode. Restore Settings Yes Select Yes to restore all items in the Printer Setup menu to their default settings.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Show Total Prints XXXXXX m2 (XXXXXX ft2) Displays the total area of media printed (to a maximum of six digits). The Printer Status Menu These items track printer use and settings. Item Parameter Explanation Print Status Sheet Print Print a status sheet showing current printer settings. Use this option to view a variety of information about the printer on a single sheet.
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Language Japanese Select the language used in the control panel display. English French Italian German Portuguese Spanish Dutch Russian Korean Chinese Unit: Length m Choose the units of length used in the control panel display and when printing test patterns. ft/in Alert Sound Setting On Off Alert Lamp Setting On Enable (On) or disable (Off) the buzzer that sounds when an error occurs.
SC-F7000 Series User’s Guide Problem Solver Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages What to do Prepare empty waste ink bottle. The waste ink bottle is getting full. Ready a new waste ink bottle. U “Options and Consumable Products” on page 85 Chip Unit Error Chip unit not recognized. Reattach or replace. ❏ Remove and reinsert the chip unit. If the same error still occurs, replace with a new chip unit.
SC-F7000 Series User’s Guide Problem Solver Messages What to do Media Size Error Load correct size media. The media currently loaded is not the correct width. Raise the media loading lever and remove the media. The narrowest width supported by the printer is 300 mm. Be sure the media is at least 300 mm wide. If this message is displayed even though the media is the correct width, the printer may print if Off is selected for Media Size Check.
SC-F7000 Series User’s Guide Problem Solver You cannot print under the network environment. Troubleshooting You cannot print (because the printer does not work) o Ask your network administrator for the network settings. The printer does not turn on. o o Is there any problem with the electrical outlet? The printer has an error. Make sure your outlet works by connecting the power cable for another electric product. o The printer is not communicating with the computer.
SC-F7000 Series User’s Guide Problem Solver Test Pattern Does Not Print Correctly o o Are you using an old ink pack? The print quality declines when an old ink pack is used. Use a new ink pack. Use all the ink in the ink pack before the date printed on ink pack. Perform head cleaning. The nozzles may be clogged. Print a test pattern again after performing head cleaning.
SC-F7000 Series User’s Guide Problem Solver o Is the media wide enough for the print data? o Although printing normally stops if the print image is wider than the media, data will be printed beyond the edges of the media if Off is selected for Media Size Check in the setup menu. Choose On for Media Size Check in the setup menu. Is the print head scuffing the printed surface? Smear caused by the print head scuffing the media can be prevented by adjusting the Platen Gap to suit the media.
SC-F7000 Series User’s Guide Problem Solver Printing does not stop when the roll ends o Important: c Cease use of the printer if the media holding plates are deformed. Continued use could damage the pressure rollers or print head. Is Off selected for Tension Measurement? Periodically is recommended in most circumstances. Contact your dealer or Epson Support. U “Tension Measurement” on page 45 D Removing Jammed Media If the print head is over the media, move it away from the jam.
SC-F7000 Series User’s Guide Problem Solver H Remove any media that remains inside the printer. I Turn on the power to the printer and perform a nozzle check. Check the printed check pattern, and if there are any clogs, perform head cleaning. U “Checking for clogged nozzles” on page 51 c IfImportant: the printer is left off for an extended period, the print head will be left uncapped and dry out, and will not print properly when printing resumes.
SC-F7000 Series User’s Guide Appendix Appendix Options and Consumable Products The following options and consumable products are available for use with your printer.(as of September 2012) For the latest information, see the Epson Web site. Important: c Refilling the ink tank with an ink pack not specified in this manual can damage the printer. Epson is not responsible for any damages or injuries incurred through the use of unspecified Epson genuine ink packs, even if the printer is still within warranty.
SC-F7000 Series User’s Guide Appendix Supported Media Moving and Transporting the Printer The following media can be used with the printer. This section describes how to move and transport the product. Print quality is greatly affected by the type and quality of media used. Choose a media suited to the task at hand. For information on use, refer to the documentation supplied with the media or contact the manufacturer.
SC-F7000 Series User’s Guide Appendix E F Unlock the stand. Transport Release the caster locks on the left and right legs and fully raise the adjusters. Before transporting the printer, contact your dealer or Epson Support. Move the printer. Important: c Use the casters on the dedicated printer stand to move the printer indoors a short distance over a level floor. They can not be used for transport. Post-Move Setup After moving the printer, follow the steps below to ready it for use.
SC-F7000 Series User’s Guide Appendix System Requirements Printer Specifications Operating Temperature/Humidity Range Consult the documentation for your software RIP.
SC-F7000 Series User’s Guide Appendix Important: c The ink will freeze if stored for a long period of time at -20°C or below. If the ink is frozen, store for at least 4 hours at room temperature (25°C) before using.(With no condensation.) Standards and Approvals Safety UL 60950-1 CSA C22.2 No.
SC-F7000 Series User’s Guide Where To Get Help Where To Get Help Contacting Epson Support Technical Support Web Site Before Contacting Epson If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting information in your product documentation, contact Epson support services for assistance. If Epson support for your area is not listed below, contact the dealer where you purchased your product.
SC-F7000 Series User’s Guide Where To Get Help Help for Users in North America Help for Users in Europe Epson provides the technical support services listed below. Check your Pan-European Warranty Document for information on how to contact Epson support. Internet Support Help for Users in Australia Visit Epson’s support website at http://epson.com/ support and select your product for solutions to common problems.
SC-F7000 Series User’s Guide Where To Get Help ❏ Sales enquiries and product information We encourage you to have all the relevant information on hand when you ring. The more information you prepare, the faster we can help solve the problem. This information includes your Epson product documentation, type of computer, operating system, application programs, and any information you feel is required.
SC-F7000 Series User’s Guide Where To Get Help Bandung Lippo Center 8th floor Jl. Gatot Subroto No.2 Bandung Technical Support Hotline You can also contact our technical staff at the following telephone and fax numbers: Phone/Fax: (62) 22-7303766 Surabaya Hitech Mall lt IIB No. 12 Jl. Kusuma Bangsa 116 – 118 Surabaya Phone: (62) 31-5355035 Fax: (62)31-5477837 Yogyakarta Hotel Natour Garuda Jl. Malioboro No.
SC-F7000 Series User’s Guide Where To Get Help World Wide Web (http://www.epson.co.in) Information on product specifications, drivers for download, and products enquiry are available. Epson India Head Office - Bangalore Phone: 080-30515000 Fax: 30515005 Trunk Line: (63-2) 706 2609 Fax: (63-2) 706 2665 Helpdesk Direct Line: (63-2) 706 2625 E-mail: epchelpdesk@epc.epson.com.ph World Wide Web (http://www.epson.com.
SC-F7000 Series User’s Guide Software License Terms Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version (“Bonjour Programs”). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.2 or its latest version until five (5) years after the discontinuation of same model of this printer product.
SC-F7000 Series User’s Guide Software License Terms 1.6 “Modifications” mean any addition to, deletion from, and/or change to, the substance and/or structure of the Original Code, any previous Modifications, the combination of Original Code and any previous Modifications, and/ or any respective portions thereof.
SC-F7000 Series User’s Guide Software License Terms 2.3 Distribution of Executable Versions. In addition, if You Externally Deploy Covered Code (Original Code and/or Modifications) in object code, executable form only, You must include a prominent notice, in the code itself as well as in related documentation, stating that Source Code of the Covered Code is available under the terms of this License with information on how and where to obtain such Source Code. 2.4 Third Party Rights.
SC-F7000 Series User’s Guide Software License Terms 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies. You expressly acknowledge and agree that use of the Covered Code, or any portion thereof, is at Your sole and entire risk.
SC-F7000 Series User’s Guide Software License Terms (c) automatically without notice from Apple if You, at any time during the term of this License, commence an action for patent infringement against Apple; provided that Apple did not first commence an action for patent infringement against You in that instance. 12.2 Effect of Termination. Upon termination, You agree to immediately stop any further use, reproduction, modification, sublicensing and distribution of the Covered Code.
SC-F7000 Series User’s Guide Software License Terms EXHIBIT A. “Portions Copyright (c) 1999-2003 Apple Computer, Inc. All Rights Reserved. This file contains Original Code and/or Modifications of Original Code as defined in and that are subject to the Apple Public Source License Version 2.0 (the ‘License’). You may not use this file except in compliance with the License. Please obtain a copy of the License at http://www.opensource.apple.com/apsl/ and read it before using this file.
SC-F7000 Series User’s Guide Software License Terms 3. Altered versions--including, but not limited to, ports to new operating systems, existing ports with new graphical interfaces, versions with modified or added functionality, and dynamic, shared, or static library versions not from Info-ZIP--must be plainly marked as such and must not be misrepresented as being the original source or, if binaries, compiled from the original source.
