English User’s Manual M00061301EN
English No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions.
English Important Safety Information This section presents important information intended to ensure safe and effective use of this product. Read this section carefully and store it in an accessible location. Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. WARNING: Warnings must be followed carefully to avoid serious bodily injury.
English Be sure to set this equipment on a firm, stable, horizontal surface. The product may break or cause injury if it falls. Do not use in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage or fire. Do not place heavy objects on top of this product. Never stand or lean on this product. Equipment may fall or collapse, causing breakage and possible injury. To ensure safety, unplug this product before leaving it unused for an extended period.
English Part Names Status LED Paper ejection guide Error Replace Ink Check Paper Paper Jam Release lever Ink cartridge slot Roll paper cover Control Panel Status LED: green/orange The green LED lights when there is no error. The orange LED flashes when there is an error. (Power) LED: green Lights when the power is on. Flashes when the printer is initializing, cleaning, printing, or during an error state. Error LED: orange Lights when the printer is in the error state.
English Power button Press the Power button for 3 seconds or more to reset the printer. After the reset, paper feeding and autocutting are performed. Note: For 30 seconds after a reset, the printer and host cannot communicate. After resetting, the printer is in the same state as when the power is turned on. Setup Follow in order the steps below to set up the printer. 1. Installing the printer. (See page 7.) 2. Connecting the Interface Cable. (See page 8.) 3. Installing/Replacing the Roll Paper.
English Installing the Printer CAUTION: Do not place the printer in a dusty place. Make sure no cables or other objects are caught under the printer. Do not put objects heavier than 700 g {1.5 lb} (two paper rolls) on the printer. Do not put beverages or vases on the printer. Do not tilt the printer during initial ink filling, printing, or head cleaning. Otherwise, ink may leak out of the printer. ❏ You must place the printer horizontally (back to front: ±10°, right to left: ±10°).
English Connecting the Interface Cable WARNING: Should a fault ever occur in the AC adapter, immediately turn off the power to the printer and remove the AC cable from the outlet. Unplug the power cable of the AC adapter from the outlet before you plug/ unplug the AC adapter into the printer. CAUTION: Direct connection to an aerial LAN cable located outside may cause induced lightning to damage devices. When you use such cables, connect via devices that protect against surges.
English 4. Insert the connector of the AC cable to the inlet of the AC adapter. 5. Connect the DC cable of the AC adapter to the power connector of the printer. 6. Connect the other side of the USB/Ethernet cable to a host computer/ network hub. Plug the AC cable into the outlet. 7. Installing/Replacing the Roll Paper CAUTION: Do not touch the autocutter blade when you open the roll paper cover. Otherwise, you may be injured. 1. 2. Turn on the printer and make sure the (Power) LED lights.
English CAUTION: Do not touch the release lever during printing, paper feeding, or cleaning. Do not touch the gears on the roll paper cover when you open it. 3. 4. Remove the paper roll core if any. Load the roll paper in the orientation shown below. 5. Pull out the paper end to the paper exit, and then close the roll paper cover. 6. When the roll paper cover is closed, roll paper is automatically fed about 10 cm {3.9"}, and then autocutting is performed.
English Note: After loading the roll paper, head cleaning may start automatically. Wait for cleaning to be completed. Installing/Replacing the Ink Cartridge CAUTION: When you start to use the printer, it takes about 7 minutes for initial ink filling. Never open the covers, press the Power button, or turn the printer off during initial ink filling (while the (Power) LED is flashing). Otherwise, initial ink filling will be performed again from the beginning. This wastes ink.
English 1. 2. 3. 4. Turn on the printer and make sure that the (Power) LED lights. Load the roll paper. (See “Installing/Replacing the Roll Paper” on page 9.) Remove the used cartridge, if there is one. Insert the new ink cartridge into the ink cartridge slot until it stops. When install the ink cartridge for the first time, use the STARTER CARTRIDGE included with the printer. When the ink cartridge is installed for the first time, the (Power) LED starts flashing, and ink charging starts.
English 2. 3. For a 32bit OS, double-click on the icon “c71d32_xxxx.exe.” For a 64bit OS, double-click on the icon “c71d64_xxxx.exe.” Complete the installation by following the instructions displayed. For Ethernet Interface Model 1. 2. 3. 4. 5. 6. Make sure the printer is turned on. Set the IP address to the printer by using EPSON TMNet WinConfig. Click [Start] - [Control Panel] - [Printer] (or [Printers and Faxes]). From the menu, click [File] - [Add Printer]. Click [Add a local printer].
English Follow the steps below to perform head cleaning. (You can also use the printer driver for head cleaning. For details, see the printer driver help.) 1. Turn on the printer. 2. Press the Cleaning button for 3 seconds or more. Head cleaning starts, and the (Power) LED starts flashing. When head cleaning finishes, the (Power) LED stays on. CAUTION: Do not do not turn off the printer or open the roll paper cover while the (Power) LED is flashing.
English Current consumptio n Ready Mean: Approx. 30 W Sleep Mean: Approx.
English ifupdown-0.6.8 kernel-2.6.18 lsp-arm-versatile926ejs-2.6.18_pro500 module-init-tools-3.2pre1 mount-2.12 netbase-4.29 psmisc-21.5 readline-libs-5.0 sysvinit-2.86 udev-0.093 util-linux-2.12 GNU LGPL This printer product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version (“LGPL Programs”). The list of LGPL Programs: uclibc-0.9.29 libusb-libs-0.1.12 zeroconf 0.6.
The list of Sun RPC Programs: English netkit-inetd-0.17 portmap-5beta TCP Wrappers License This printer product includes the open source software program “libwrap-libs7.6” which applies the terms and conditions provided by owner of the copyright to the “TCP Wrappers”. libncurses License This printer product includes the open source software program “libncurses-5.4” which applies the terms and conditions provided by owner of the copyright to the “libncurses”.
English WEEE (Waste Electrical and Electronic Equipment) Directive This information only applies to customers in the European Union, according to Directive 2012/19/EU OF T HE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 04 July 2012 on waste electrical and electronic equipment (WEEE) and legislation transposing and implementing it into various national legal systems, and to customers in countries in Europe, Middle East and Africa (EMEA) where they have implemented equivalent regulations.
English Norsk Eesti Det er krysset over merket av beholderen på hjul som vises på produktet, som angir at dette produktet ikke skal kastes sammen med vanlig husholdningsavfall. Hold dette produktet atskilt fra annet avfall slik at det kan resirkuleres på en miljømessig forsvarlig måte og dermed forhindre eventuell skade på miljø eller helse. Hvis du vil ha mer informasjon om hvor produktet kan leveres inn, kontakter du kommunale myndigheter eller forhandleren der du kjøpte dette produktet.
English Română Eticheta arătând un coş de gunoi tăiat cu două linii încrucişate, care poate fi găsită pe produs, indică faptul că acesta nu trebuie aruncat la gunoi laolaltă cu gunoiul menajer. Pentru a evita posibila degradare a mediului înconjurător sau a sănătăţii umane, colectaţi separat acest produs de gunoiul menajer pentru a vă asigura că poate fi reciclat într-un mod ecologic.
