TM-T88II_eng_um.
TM-T88II_eng_um.book Page ii Thursday, August 29, 2002 6:11 PM Printer Parts and Labels Printer cover Control panel POWER PO WE R ER RO R P OU APE R FE T ED ERROR PAPER OUT FEED FEED Cutter cover Cover open button Caution Labels Labels CAUTION: Thermal head is hot. Label inside cutter section ATTENTION: La téte thermique est chaude. Label inside printer cover VORSICHT: Der Thermalkopf ist heiß. Caution label above for the drawer kick-out connector.
TM-T88II_eng_um.book Page i Thursday, August 29, 2002 6:11 PM Quick Reference This Quick Reference will direct you to key areas of this User’s Manual. For a complete listing of topics, see the Contents. Printer Parts and Labels Setting Up the Printer inside front cover page 1-1 How to set up the printer. Installing and Replacing Paper page 1-7 How to load or change the paper roll. Solving Problems page 3-1 How to correct problems.
TM-T88II_eng_um.book Page ii Thursday, August 29, 2002 6:11 PM All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
TM-T88II_eng_um.book Page iii Thursday, August 29, 2002 6:11 PM EMC and Safety Standards Applied Product Name: TM-T88II Model Name: M129B The following standards are applied only to the printers that are so labeled. (EMC is tested using the EPSON PS-170 power supply) Europe: CE Marking Safety: EN60950 North America: EMI: FCC/ICES-003 Class A Safety: UL 1950/CSA C22.2 No.
TM-T88II_eng_um.book Page iv Thursday, August 29, 2002 6:11 PM CE Marking The printer conforms to the following Directives and Norms Directive 89/336/EEC EN 55022 Class B EN 55024 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-11 Directive 90/384/EEC EN45501 FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
TM-T88II_eng_um.book Page v Thursday, August 29, 2002 6:11 PM GEREÄUSCHPEGEL Gemäß der Dritten Verordnung zum Gerätesicherheitsgesetz (Maschinenlärminformations- Verordnung-3. GSGV) ist der arbeitsplatzbezogene Geräusch-Emissionswert kleiner als 70 dB(A) (basierend auf ISO 7779).
TM-T88II_eng_um.book Page vi Thursday, August 29, 2002 6:11 PM About This Manual Setting Up and Using ❏ Chapter 1 contains information on unpacking the printer and setting it up. ❏ Chapter 2 contains information on using the printer. ❏ Chapter 3 contains troubleshooting information. Reference ❏ Chapter 4 contains specifications. ❏ Appendix A tells how to change the DIP switch and paper near end settings.
TM-T88II_eng_um.book Page vii Thursday, August 29, 2002 6:11 PM Introduction Features TM-T88II Series printers are high-quality POS printers that can print on a paper roll. The printers have the following features: Printing ❏ High-speed printing: 28.4 lines/second (4.23mm (1/6”) feed) maximum. ❏ Low-noise thermal printing. ❏ High reliability due to a stable mechanism. Application Software ❏ Command protocol is based on the ESC/POS® standard. ❏ Various layouts are possible by using page mode.
TM-T88II_eng_um.book Page viii Thursday, August 29, 2002 6:11 PM Options and Accessories ❏ EPSON power supply unit, PS-170. ❏ Affixing tapes (model: DF-10). ❏ RS-485 interface board can be installed as a dealer option. ❏ Wall hanging bracket set (WH-10).
TM-T88II_eng_um.book Page ix Thursday, August 29, 2002 6:11 PM Contents Chapter 1 Setting Up the Printer Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Connecting the Cables and Grounding the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Connecting the Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Grounding the Printer . . . . . . . . . . . . . . .
TM-T88II_eng_um.book Page x Thursday, August 29, 2002 6:11 PM Appendix A DIP Switch and Paper Near End Settings Setting the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP switch functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the Paper Near End Detector . . . . . . . . . .
TM-T88II_eng_um.book Page 1 Thursday, August 29, 2002 6:11 PM Chapter 1 Setting Up the Printer Unpacking The illustration below shows the items included for the standard specification printer.
TM-T88II_eng_um.book Page 2 Thursday, August 29, 2002 6:11 PM Connecting the Cables and Grounding the Printer You can connect up to four cables to the printer. They all connect to the connector panel on the back of the printer, which is shown below: FG FG DK DC24V Power supply Interface (The shape of the interface connector is different from the illustration if the printer has a parallel interface.) Drawer kick-out Grounding screw Note: There is a caution label above the drawer kick-out connector.
TM-T88II_eng_um.book Page 3 Thursday, August 29, 2002 6:11 PM 2. If the printer has a serial interface, tighten the screws on both sides of the cable connector. If the printer has a parallel interface, squeeze the wire clips on the printer together until they lock in place on both sides of the connector. 3. Attach the other end of the cable to the computer. Connecting the Drawer WARNING: Use a drawer that matches the printer specifications.
TM-T88II_eng_um.book Page 4 Thursday, August 29, 2002 6:11 PM CAUTION: Do not connect a telephone line to the drawer kick-out connector; otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick-out connector on the back of the printer next to the power supply connector. Anschließen der Schublade WARNUNG: Eine für den Drucker geeignete Schublade verwenden. Bei Verwendung einer falschen Schublade kann diese oder der Drucker beschädigt werden.
TM-T88II_eng_um.book Page 5 Thursday, August 29, 2002 6:11 PM Das Kabel der Schublade an die Schnappsteckerbuchse hinten am Drucker neben dem Netßzanschluß anschließen. Grounding the Printer You need a ground wire to ground your printer. Make sure the wire is AWG 18 or equivalent. 1. Be sure the printer is turned off. 2. Connect the ground wire to the printer using one of the FG screws on the back of the printer, as shown.
TM-T88II_eng_um.book Page 6 Thursday, August 29, 2002 6:11 PM WARNING: Make sure you use the EPSON PS-170 power supply or equivalent. Using an incorrect power supply may cause fire or electrical shock. CAUTION: When connecting or disconnecting the power supply from the printer, make sure the power supply is not plugged into an electrical outlet. Otherwise you may damage the power supply or the printer.
TM-T88II_eng_um.book Page 7 Thursday, August 29, 2002 6:11 PM Installing or Replacing the Paper Roll Note: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core, because the printer cannot detect the paper end correctly. 1. Make sure the printer is not receiving data; otherwise, data may be lost. 2. Open the paper roll cover by pressing the cover-open button.
TM-T88II_eng_um.book Page 8 Thursday, August 29, 2002 6:11 PM 4. Insert the paper roll as shown. PO WE ER R RO R P OU AP E R FE T ED 5. Be sure to note the correct direction that the paper comes off the roll.
TM-T88II_eng_um.book Page 9 Thursday, August 29, 2002 6:11 PM 6. Pull out a small amount of paper, as shown. Then close the cover. PO WE ER R RO R P OU APE R FE T ED 7. Tear off the paper as shown.
TM-T88II_eng_um.book Page 10 Thursday, August 29, 2002 6:11 PM Using the Power Switch Cover WARNING: If an accident occurs when the power switch cover is attached, unplug the power supply cord from the outlet immediately. Continued use may lead to fire or shock. You can use the enclosed power switch cover to make sure the power switch is not pressed accidentally. If you want to use this cover, install it as shown in the illustration below.
TM-T88II_eng_um.book Page 11 Thursday, August 29, 2002 6:11 PM 2. While holding down the FEED button, turn on the printer using the switch on the front of the printer to begin the self test. The self test prints the printer settings and then prints the following, cuts the paper, and pauses. (The PAPER OUT light blinks.) Self test printing. Please press the PAPER FEED button. 3. Press the FEED button to continue printing. The printer prints a pattern using the built-in character set. 4.
TM-T88II_eng_um.book Page 12 Thursday, August 29, 2002 6:11 PM Adjustments and Settings TM-T88II Series printers are set up at the factory to be appropriate for almost all users. There are, however, some settings for users with special requirements. Your printer has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density. TM-T88II Series printers also have a near-end sensor for the paper. This can warn you when the paper is almost out.
TM-T88II_eng_um.book Page 1 Thursday, August 29, 2002 6:11 PM Chapter 2 Using the Printer Operating the Control Panel You can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you monitor the printer’s status. Control Panel POWER ERROR PAPER OUT FEED Button The button can be disabled by the ESC c 5 command. Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed paper continuously.
TM-T88II_eng_um.book Page 2 Thursday, August 29, 2002 6:11 PM Panel lights POWER The POWER light is on whenever the printer is on. ERROR This indicates an error. See Chapter 3 for information on what to do when this light comes on. PAPER OUT This light indicates the near end of the paper roll. Install a new paper roll, and the printer will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution standby state when the macro execution command is used.
TM-T88II_eng_um.book Page 1 Thursday, August 29, 2002 6:11 PM Chapter 3 Troubleshooting Troubleshooting This chapter gives solutions to some printer problems you may have. General problems The lights on the control panel do not come on. Make sure the power supply cables are correctly plugged into the printer, the power unit, and into the power outlet. Make sure power is supplied to the power outlet. If the outlet is controlled by a switch or timer, use another outlet.
TM-T88II_eng_um.book Page 2 Thursday, August 29, 2002 6:11 PM If there is no paper jam and the printer has been printing for quite a while, the print head may be overheated. If the print head is overheated, the printer will resume printing when the head has cooled (usually within two or three minutes). If there is no paper jam and the print head is not overheated, turn off the printer and turn it back on after about 10 seconds. If the ERROR light is still flashing, contact a qualified service person.
TM-T88II_eng_um.book Page 3 Thursday, August 29, 2002 6:11 PM Cleaning the print head CAUTION: After printing, the print head can be very hot. Be careful not to touch it. Also let it cool before you clean it. Do not damage the print head by touching it with your fingers or any hard object. 1. Open the printer cover. 2. Clean the thermal element of the print head with a cotton swab moistened with an alcohol solvent (ethanol, methanol, or IPA).
TM-T88II_eng_um.book Page 4 Thursday, August 29, 2002 6:11 PM To clear a paper jam, follow the steps below: 1. Turn the printer off and press the cover open button to open the cover. 2. Remove the jammed paper, put the roll back in the printer, and close the cover. 3. If paper is caught in the automatic cutter and the printer cover cannot be opened, open the cutter cover as shown below.
TM-T88II_eng_um.book Page 5 Thursday, August 29, 2002 6:11 PM 4. Then turn the knob until you see in the opening, as shown in the illustration below. This returns the cutter blade to the normal position. Also notice that there is a label near the cutter to assist you. ADJUSTMENT: TURN KNOB UNTIL YOU SEE TRIANGLE IN OPENING PO WE ER R RO R P OU APE R FE T ED 5. Close the cutter cover. 6. Open the printer cover. 7. Remove the jammed paper. Auto cutter problems The auto cutter is jammed.
TM-T88II_eng_um.book Page 6 Thursday, August 29, 2002 6:11 PM If the auto cutter does not return to its normal position by itself, follow the steps below to correct the problem: 1. Pull the cutter cover toward you so that you can rotate the cutter motor knob. PO ER P O AP FE UT ER FEED ED RO WE R R 2. Following the instructions on the label, rotate the knob until the appears in the hole. ADJUSTMENT: TURN KNOB UNTIL YOU SEE TRIANGLE IN OPENING 3. Close the cutter cover.
TM-T88II_eng_um.book Page 7 Thursday, August 29, 2002 6:11 PM Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hex dump function, the printer prints all commands and other data in hexadecimal format, along with a guide section to help you find specific commands. To use the hex dump feature, follow these steps: 1. After you make sure the printer is off, open the cover. 2.
TM-T88II_eng_um.
TM-T88II_eng_um.book Page 1 Thursday, August 29, 2002 6:11 PM Chapter 4 Reference Information Printing Specifications Printing method: Thermal line printing Dot density: 180 dpi × 180 dpi [the number of dots per 25.4 mm (1”)] Printing direction: Unidirectional with friction feed Printing width: 72 mm (2.83”), 512 dot positions For 58 mm paper width: 50.
TM-T88II_eng_um.book Page 2 Thursday, August 29, 2002 Printing speed — when a ladder bar code is printed: 6:11 PM Approximately 42 mm/ second (approximately 1.7’’/ second) Notes: Printing speed may be slower, depending on the data transmission speed and the combination of control commands. There may be variations in printing after switching the mode of the printing speed. To prevent this for logo printing, it is recommended that you use a downloaded bit image.
TM-T88II_eng_um.book Page 3 Thursday, August 29, 2002 Standard WxH in mm (") 6:11 PM Double-height Double-width Double-width/ Double-height CPL WxH in mm (") CPL WxH in mm (") CPL WxH in mm (") CPL Font A 12 x 24 1.41 x 3.39 (0.06” x .13”) 42 1.41 x 6.77 (0.06” x .27”) 42 2.82 x 3.39 (0.11” x .13”) 21 2.82 x 6.77 (0.11” x .27”) 21 Font B 9 x 17 0.99 x 2.40 (0.04” x .09”) 56 0.99 x 4.80 (0.04” x .19”) 56 1.98 x 2.40 (0.08” x .09”) 28 1.98 x 4.80 (0.08” x .
TM-T88II_eng_um.book Page 4 Thursday, August 29, 2002 Specified thermal paper roll: 6:11 PM NTP080-80 NTP058-80 (for 58 mm paper width) In Japan: Nakagawa, Seisakujo In U.S.A.: Nakagawa Mfg. (USA) Inc. In Europe: Nakagawa Mfg. (Europe) GmbH In Southeast Asia: N.A.K. Mfg. (Malaysia) SDN BHD [Original paper: TF50KS-E Nippon Paper Industries Co., Ltd.,] The following paper can be used instead of the specified paper above: Original paper: PD 160R (Oji Paper Mfg. Co. Ltd.
TM-T88II_eng_um.book Page 5 Thursday, August 29, 2002 6:11 PM Reliability Life: Mechanism: 15,000,000 lines Thermal head: 100 million pulses, 100 km Auto cutter: 1,500,000 cuts (End of Life is defined to have reached the end of its life when it reaches the beginning of the Wearout Period.) MTBF: 360,000 hours (Failure is defined as Random Failure occurring at the time of the Random Failure Period.
TM-T88II_eng_um.
TM-T88II_eng_um.book Page 1 Thursday, August 29, 2002 6:11 PM Appendix A DIP Switch and Paper Near End Settings Although the factory settings are best for almost all uses, if you have special requirements, you can change the DIP switch or paper near end settings. Setting the DIP Switches DIP switch functions Your printer has two sets of DIP switches. The functions of the switches are shown in the following tables.
TM-T88II_eng_um.
TM-T88II_eng_um.book Page 3 Thursday, August 29, 2002 6:11 PM Print Density Selection Print Density SW 2-3 SW 2-4 1 Low power consumption mode ON ON 2 (Normal) OFF OFF 3 ON OFF 4 (Dark) OFF ON Notes: • With the optional RS-485 interface, DIP switches 2-7 and 2-8 are disabled. • Changes in DIP switch settings (excluding switches 2-7 and 2-8 interface reset signals) are recognized only when the printer power is turned on or when the printer is reset by using the interface.
TM-T88II_eng_um.
TM-T88II_eng_um.book Page 5 Thursday, August 29, 2002 6:11 PM Notes: • Changes in DIP switch settings (excluding switch 2-8 interface reset signal) are recognized only when printer power is turned on or when the printer is reset using the interface. If the DIP switch setting is changed after printer power is turned on, the change does not take effect until the printer is turned on again or is reset.
TM-T88II_eng_um.book Page 6 Thursday, August 29, 2002 6:11 PM Changing the DIP switch settings If you need to change settings, follow the steps below to make your changes: CAUTION: Turn off the printer before removing the DIP switch cover to prevent an electric short, which can damage the printer. 1. Make sure the printer is turned off. 2. Remove the screw from the DIP switch cover. Then take off the DIP switch cover, as shown in the illustration below. DSW1 DSW2 3.
TM-T88II_eng_um.book Page 7 Thursday, August 29, 2002 6:11 PM Adjusting the Paper Near End Detector The paper near end detector detects when paper is almost gone by measuring the diameter of the paper roll. The detector has two settings. Because of variations in paper roll cores, it is not possible for the detector to measure the exact length of the paper left on the roll when the detector is triggered.
TM-T88II_eng_um.book Page ii Thursday, August 29, 2002 6:11 PM Printed in China 1999.