PowerLite® 5510/5520W/5530U/5535U User's Guide
Contents PowerLite 5510/5520W/5530U/5535U User's Guide................................................................................ 11 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents................................................................
Connecting to a Component Video Source ............................................................................... Connecting to a Video Source for Sound .................................................................................. Connecting to an HDBaseT Transmitter ....................................................................................... Connecting to an External Computer Monitor................................................................................
Using Basic Projector Features ............................................................................................................... 80 Turning On the Projector .................................................................................................................... 80 Using the Home Screen................................................................................................................. 82 Turning Off the Projector .........................................................
Adjusting Projector Features ................................................................................................................. Shutting Off the Picture and Sound Temporarily .............................................................................. Stopping Video Action Temporarily .................................................................................................. Zooming Into and Out of Images ...............................................................................
Adjusting the Menu Settings .................................................................................................................. Using the Projector's Menus............................................................................................................. Image Quality Settings - Image Menu .............................................................................................. Input Signal Settings - Signal Menu..................................................................
Solutions When Only a Partial Image Appears ............................................................................ 194 Solutions When the Image is Not Rectangular ............................................................................ 194 Solutions When the Image Contains Noise or Static ................................................................... 195 Solutions When the Image is Fuzzy or Blurry ..............................................................................
Binding Arbitration and Class Waiver ............................................................................................... Trademarks ...................................................................................................................................... Copyright Notice............................................................................................................................... A Note Concerning Responsible Use of Copyrighted Materials...............................
PowerLite 5510/5520W/5530U/5535U User's Guide Welcome to the PowerLite 5510/5520W/5530U/5535U User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• Epson's Instant Off and Direct Power On features for quick setup and shut down • Support for Crestron RoomView network monitoring systems • Network message broadcast system to project timely messages to all networked projectors (Windows only) Note: The PowerLite 5530U/5535U is shown in most illustrations in this manual, unless noted otherwise.
Make sure your projector box included all of these parts: 1 Projector with lens cap 2 Cable cover 3 Remote control 4 Remote control batteries (two AA alkaline) 5 Power cord 6 VGA computer cable 7 Projector documentation CD 8 Projector software CD Parent topic: Projector Features 14
Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you to connect to the projector.
Note: If you still need help after checking this manual and the sources listed here, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help". Projector software Manual Description EasyMP Monitor (Windows only) EasyMP Monitor Operation Guide Lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or epson.
Option or part Part number Genuine Epson replacement lamp (ELPLP95) V13H010L95 Replacement air filter (ELPAF45) V13H134A45 Wireless LAN module (ELPAP10) V12H731P02 HDBaseT transmitter (ELPHD01) V12H547020 Remote control cable set (ELPKC28) V12H005C28 Epson DC-11 document camera (ELPDC11) V12H377020 Epson DC-13 document camera (ELPDC13) V12H757020 Epson DC-20 document camera (ELPDC20) V12H500020 Epson DC-21 document camera (ELPDC21) V12H758020 Wireless IR mouse receiver for remote control
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information.
Parent topic: Introduction to Your Projector Projector Parts - Front/Top 1 Exhaust vent 2 Focus ring 3 Projection lens 4 Zoom ring 5 Remote receivers 6 Status lights 7 Air filter cover/intake vent 8 Air filter cover latch 9 Wireless LAN module cover 10 Wireless LAN module light 19
11 Cable cover 12 Vertical lens shift dial 13 Lens shift dial lock 14 Horizontal lens shift dial 15 Lamp cover 16 Kensington security slot Parent topic: Projector Part Locations Projector Parts - Rear 1 AC input 2 Interface ports 3 Control panel 4 Speaker Parent topic: Projector Part Locations 20
Projector Parts - Interface Ports 1 Computer port 2 BNC ports 3 Monitor Out port 4 Audio Out port 5 RS-232C port 6 Cable clip slot 7 Remote port 8 Audio2 port 9 Audio1 port 10 Service port 11 HDMI2 port 12 HDMI1 port 13 HDBaseT port (PowerLite 5520W/5530U/5535U) 14 Network LAN port Parent topic: Projector Part Locations 21
Projector Parts - Base 1 Security cable attachment point 2 Rear feet 3 Screw hole for cable cover 4 Mounting bracket holes 5 Front adjustable foot Parent topic: Projector Part Locations 22
Projector Parts - Control Panel 1 Power button (turns on the projector) 2 Source Search button (searches for connected sources) 3 A/V Mute button (turns the video and audio on or off) 4 Left arrow button and displays the Control Panel Lock screen 5 Down arrow button and displays a test pattern 6 Enter button (selects options) 7 Right arrow button and displays the Info menu 8 Esc button (cancels/exits functions) 9 Up arrow button and displays screen adjustment options 10 Menu button (acce
Projector Parts - Remote Control 24
1 On button (turns on the projector) 2 Standby button (turns off the projector) 3 Source buttons (select an image source) 4 User1, User2, and User3 buttons (open menu assigned by user) 5 Aspect button (selects the image aspect ratio) 6 Auto button (automatically adjusts computer images) 7 Test Pattern button (displays a test pattern) 8 Freeze button (stops video action) 9 Menu button (accesses projector menu system) 10 Arrow buttons (move through on-screen options and move pointer) 11 E
28 Color Mode button (selects display modes) 29 Search button (searches for connected sources) 30 Light button (lights up the remote control buttons temporarily) 31 Indicator light (lights up when the remote control is in use) 32 Remote control signal emitter (emits remote control signals) Parent topic: Projector Part Locations 26
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Attaching and Removing the Cable Cover Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front ceiling Rear ceiling 28
Note: Be sure to leave at least 20 inches (50 cm) of space in front of the air exhaust and intake vents and, when setting up multiple projectors, 20 inches (50 cm) of space between the projectors. If you mount the projector to the ceiling, it can be installed at the following angles: • Vertically: Any angle up to ±30°. • Horizontally: Can be tilted within the range of the rear feet.
Parent topic: Projector Placement Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
PowerLite 5510 4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Wide to Tele 50 inches 50 to 103 inches Vertical lens shift from bottom to top (2) –32.7 to 2.7 inches (–83 to 7 cm) (127 to 261 cm) 80 inches 81 to 166 inches (206 to 421 cm) 100 inches 102 to 208 inches (258 to 527 cm) 150 inches 153 to 312 inches –52.3 to 4.3 inches (–133 to 11 cm) –65.3 to 5.
Projector Connections See these sections to connect the projector to a variety of projection sources. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
3. Connect the other end to a Computer port on the projector. 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
2. Connect the other end to one of the projector's HDMI ports. Note: The projector converts the digital audio signal sent from your computer into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers. Note: If you have problems hearing audio through the HDMI connection, you can use one of the projector's audio ports instead to play sound. Connect one end of an optional 3.
2. Connect the 5 BNC connectors to the projector's BNC ports. Parent topic: Connecting to Computer Sources Related references Additional Components Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it to the projector's HDMI port, you can still play sound through the projector's speaker system. Just connect an optional 3.5 mm stereo mini-jack audio cable as described here. 1.
2. Connect the other end to the Audio port that corresponds to the Computer or BNC port you are using. Parent topic: Connecting to Computer Sources Related references Additional Components Related tasks Connecting to an External Computer Monitor Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
2. Connect the other end to one of the projector's HDMI ports. Note: The projector converts the digital audio signal sent from your video source into a mono analog signal for the internal speaker or a stereo analog signal if you are connecting to external speakers. Note: If you have problems hearing audio through the HDMI connection, you can use one of the projector's audio ports instead to play sound. Connect one end of an optional 3.
2. Connect the BNC connectors to the projector's R/Cr/Pr, G/Y, B/Cb/Pb ports. Parent topic: Connecting to Video Sources Related references Additional Components Connecting to a Component Video Source If your video source has component video ports, you can connect it to the projector using an optional component-to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1.
2. Connect the VGA connector to a Computer port on the projector. 3. Tighten the screws on the VGA connector. If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Signal menu. Parent topic: Connecting to Video Sources Related references Additional Components Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports.
2. Connect the other end of the cable to the projector's Audio port that corresponds to the Computer or BNC port you are using for video. Parent topic: Connecting to Video Sources Related tasks Connecting to an External Computer Monitor Connecting to an HDBaseT Transmitter To send an HDMI or RS-232C signal over a long distance, you can connect the projector to an optional HDBaseT transmitter using a 100Base-TX network cable.
3. Connect the other end to the projector's HDBaseT port. Note: See the documentation that came with the HDBaseT transmitter for instructions on connecting it to your video device or computer. 4. Turn on the projector and HDBaseT transmitter. Note: To enable communication from the Ethernet and serial ports on the transmitter, select On as the Control Communications setting in the projector's Extended menu. Turning on this setting disables the projector's LAN, RS-232C, and Remote ports.
Note: Monitors that use a refresh rate less than 60 Hz may not be able to display images correctly. 1. Make sure your computer is connected to the projector's Computer or BNC port. 2. Connect the external monitor's cable to your projector's Monitor Out port. Note: If you do not see an image on the external monitor, you may need to change the Monitor Out setting in the Extended menu.
If you want to output audio from the external speakers when the projector is turned off, you need to select Communication On for the Standby Mode setting and Always On for the A/V Output setting in the projector's Extended menu. Note: The projector's built-in speaker system is disabled when you connect external speakers. 1. Make sure your computer or video source is connected to the projector with both audio and video cables as necessary. 2.
1. Bundle the cables together using a band or other fastener (not provided). Caution: Do not bundle the power cord to the other cables. Otherwise, a fire may occur. 2. Place the cable cover on the projector as shown, guiding the cables through the notch on the base of the cable cover.
3. Tighten the cable cover screw. To remove the cover, loosen the cover screw and pull the cover off of the projector. Parent topic: Setting Up the Projector Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
1. Remove the battery cover. 2. Insert the batteries with the + and – ends facing as shown.
3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Crestron RoomView Support Wired Network Projection You can project through a wired network.
2. Connect the other end of the cable to the projector's LAN port. Parent topic: Wired Network Projection Selecting Wired Network Settings Before you can project from computers on your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in Epson Web Control. (Default user name is EPSONREMOTE; default password is guest.) • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
8. If necessary, select IP Settings and press Enter. 9. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting. • If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter. 10.
Wireless Network Projection from a Mobile Device or Windows Computer (Screen Mirroring) Parent topic: Using the Projector on a Network Related references Additional Projector Software and Manuals Optional Equipment and Replacement Parts Installing the Wireless LAN Module To use the projector over a wireless network, install the optional Epson 802.11b/g/n wireless LAN module. Do not install any other type of wireless LAN module.
3. Loosen the screw securing the wireless LAN module cover, then remove the cover. 4. Insert the wireless LAN module into the port.
5. Replace the wireless LAN module cover and secure it using the screw you loosened. 6. Close the air filter cover. 7. Plug in and turn on the projector. Parent topic: Wireless Network Projection Related references Optional Equipment and Replacement Parts Using Quick Wireless Connection (Windows) You can create a Quick Wireless Connection USB Key to quickly connect the projector to a Windows computer wirelessly. Then you can project your presentation and remove the key when you are done.
2. Turn on the projector. 3. Press the LAN button on the remote control. You see the LAN standby screen. 4. Verify that an SSID and IP address are displayed. 5. Remove the wireless LAN module from the projector. 6. Insert the USB key into the same port used for the wireless LAN module. You see a projected message that the network information update is complete. 7. Remove the USB key. 8. Reinsert the wireless LAN module into the projector. 9. Insert the USB key into a USB port on your computer.
1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Make sure the Wireless LAN Power setting is set to On. 5. Select Network Configuration and press Enter. 6. Select the Basic menu and press Enter.
7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen in the Epson Web Control.
8. Select the Wireless LAN menu and press Enter. 9. Select the settings on the Wireless LAN menu as necessary for your network. 10. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. After you complete the wireless settings for your projector, you need to select the wireless network on your computer, or iOS or Android device.
Setting Options Description Search Access Point To Search View Search for available wireless network access points in Advanced connection mode SSID Up 32 alphanumeric characters Sets the SSID (network name) of the wireless LAN system the projector is connecting to Security Open Selects the type of wireless security used in the wireless network (some options are only available when the Connection Mode setting is set to Advanced) WPA2-PSK WPA/WPA2-PSK WPA2-EAP WPA/WPA2-EAP Passphrase Between 8 to
Setting Options Description SSID Display On Selects whether to display the SSID on the network standby screen Off IP Address Display On Selects whether to display the IP address on the network standby screen Off IPv6 Settings IPv6 Auto Configuration Selects the IPv6 settings when you connect the projector to the network using IPv6 Use Temporary Address Parent topic: Selecting Wireless Network Settings Manually Selecting Wireless Network Settings in Windows Before connecting to the projector, se
Setting Up Wireless Network Security You can set up security for your projector to use on the wireless network. Set up one of the following security options to match the settings used on your network: • WPA/WPA2-PSK security (Advanced connection mode) • WPA2-EAP security (Advanced connection mode) • WPA/WPA2-PSK security (Quick connection mode) • WPA/WPA2-EAP security (Advanced connection mode) Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button.
Related references Wireless LAN Menu Settings Using a QR Code to Connect a Mobile Device After you select the wireless network settings for your projector, you can display a QR code on the screen and use it to connect a mobile device using the Epson iProjection app. Note: Make sure you have installed the latest version of Epson iProjection on your device. Visit epson.com/iprojection (U.S.) or epson.ca/iprojection (Canada) for more information. 1. Press the Menu button. 2.
4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Press the LAN button on the remote control or select Display the QR Code in the projector's Network menu. (You can also press the Home button on the remote control and select Display the QR Code on the Home screen.) Your projector displays the QR code on the projection surface.
Screen Mirroring Restrictions Selecting Screen Mirroring Settings Connecting for Screen Mirroring with Miracast Connecting for Screen Mirroring with a Windows 8.x/10 Computer Parent topic: Wireless Network Projection Screen Mirroring Restrictions Note the following when using Screen Mirroring features (PowerLite 5520W/5530U/5535U): • You cannot project an interlaced image. • You cannot play audio with more than 3 channels.
2. Select the Network menu and press Enter. 3. Set the Screen Mirroring setting to On. 4. Select Screen Mirroring Settings and press Enter. 5. Select the Screen Mirroring Settings options as necessary. 6. When you finish selecting settings, select Set and follow the on-screen instructions to save your settings and exit the menus. 7. Press the Home button on the control panel or remote control.
Parent topic: Wireless Network Projection from a Mobile Device or Windows Computer (Screen Mirroring) Connecting for Screen Mirroring with Miracast If your mobile device supports Miracast, you can connect it to the projector wirelessly and project images and sound (PowerLite 5520W/5530U/5535U). 1. Select the Screen Mirroring settings on your projector as necessary. 2. Press the LAN button on the remote control to switch to the Screen Mirroring source. You see the Screen Mirroring standby screen. 3.
You see the Screen Mirroring standby screen. 3. Do one of the following: • Windows 10: Open Action Center and select Connect. • Windows 8.x: Select Devices > Project > Add a wireless display. 4. Select your projector's Display Name from the list. 5. If you see the PIN entry screen on your computer, enter the PIN code displayed on the Screen Mirroring standby screen or at the bottom right of the projected image. The projector displays the image from your computer or mobile device.
4. Select the Notifications menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server setting. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7. Select a number for the SMTP server Port Number setting, from 1 to 65535 (default is 25). 8. Enter the sender's email address for the From option. 9.
Parent topic: Using the Projector on a Network Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you receive an e-mail containing the following information: • The email address entered as the From setting • Epson Projector on the subject line • The name of the projector experiencing a problem • The IP address of the affected projector • Detailed information about the problem Note: If a critical problem causes a projector to
4. Select the Notifications menu and press Enter. 5. Turn on the SNMP setting. 6. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: To enter the IP address using the numeric keys on the remote control, press and hold the Num button. Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 7. Select the Others menu and press Enter.
8. If you want to use the Secure HTTP protocol to encrypt communication when using Web Control, turn on the Secure HTTP setting and import the web server certificate to the Web Server Cert. setting. 9. If available, select the Priority Gateway setting for your network. 10. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected. 11.
3. Type the projector's IP address into the browser's address box and press the computer's Enter key. You see the Web Control screen. 1 Select Basic Control to control the projector remotely. 2 Select OSD Control Pad to change the projector's menu settings. 3 Select Status Information to view the projector's status. 4 Select Advanced to open the advanced menu screen. 5 Select Test Pattern to display a test pattern 4. Select the option corresponding to the projector function you want to control.
Web Control Options Basic Control Note: If the Remote Password is set to On, you need to enter your user name and password. (The default username is EPSONREMOTE and the default password is guest).
OSD Control Pad 1 Returns to the Home screen 2 Displays the projector's setting menus 3 Use your finger or mouse to navigate the menus 4 Returns settings to their default values 5 Returns to the previous menu 6 Displays help topics Note: You cannot change some settings using Epson Web Control.
Test Pattern screen 1 Displays available test patterns; select to project a test pattern 2 Turns off test pattern display Status Information 1 Returns to the Home screen 2 Displays a list of monitored settings 3 Displays the setting status 76
4 Select to view different status information Parent topic: Controlling a Networked Projector Using a Web Browser Crestron RoomView Support If you are using the Crestron RoomView network monitoring and control system, you can set up your projector for use on the system. Crestron RoomView lets you control and monitor your projector using a web browser. Note: You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP Monitor when you use Crestron RoomView.
4. Select the Others menu and press Enter. 5. Set the Crestron RoomView setting to On to allow the projector to be detected. Note: Enabling Crestron RoomView disables the Epson Message Broadcasting feature in the EasyMP Monitor software. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Turn off the projector, then turn it on again to enable the setting.
You see this screen: 3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box. 4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons. You can scroll through button options at the bottom of the screen.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. The projector's On/Standby light turns blue. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 3. Press the power button on the projector or the On button on the remote control to turn on the projector.
• Press the Home button and select the source you want to project on the Home screen. Using the Home Screen Parent topic: Using Basic Projector Features Related references Projector Setup Settings - Extended Menu Projector Light Status Using the Home Screen You can select input sources and other frequently used options from the Home screen. 1. To display the Home screen, do one of the following: • Press the Home button on the remote control.
2 Display the QR code 3 Display the Help screen 4 Display the projector's menus 5 Select customizable menu options 6 Select to change the Power Consumption setting 7 Select to change the Color Mode Note: You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3. Press the Home button to hide the Home screen.
The projector beeps twice, the lamp turns off, and the Status light turns off. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary). 3. To transport or store the projector, make sure the Status light is off, then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status light is on or flashing blue.
6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
2. To sharpen the image focus, rotate the projector’s focus ring. Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Setting the Screen Type You can use the Screen Type setting to match the aspect ratio of the displayed image to the screen you are using. Note: This setting is unavailable when projecting images from a computer over a network. 1. Turn on the projector and display an image. 2. Press the Menu button. 3.
5. Select your screen's aspect ratio and press Enter. 6. Press the Menu button to exit. 7. Adjust the aspect ratio for the projected image, if necessary. Parent topic: Using Basic Projector Features Related concepts Image Aspect Ratio Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.
3. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary.
3 Maximum range: V × 58% Note: You cannot move the image upward when the lens is shifted horizontally all the way. PowerLite 5520W/5530U/5535U 1 Center of lens 2 Projected image when the lens is set to the home position 4. When you are finished, slide the lens shift dial lock as shown to lock the dials.
Adjusting the Image Position Using Screen Position You can adjust the image position if there are margins between the edge of the image and the projected screen frame. Note: You cannot adjust the screen position if the Screen Type setting is set to 16:10 for a WXGA/WUXGA projector model or 4:3 for a XGA projector model. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select Display > Screen > Screen Position. 5.
1. Turn on the projector. 2. Press the Test Pattern button on the remote control or the down arrow button on the control panel. 3. Press the left or right arrow button on the remote control or press Enter on the control panel to cycle through the available test patterns. 4. Adjust the image as necessary. 5. Press the Esc to clear the test pattern.
2. To adjust the image height, rotate the front foot to extend or retract it. 3. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
Correcting Image Shape with H/V Keystone You can use the projector's H/V Keystone setting to correct the shape of an image that is unevenly rectangular on the sides. Note: You cannot combine H/V Keystone correction with other image shape correction methods. 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.
3. Select the Settings menu and press Enter. 4. Select the Geometry Correction setting and press Enter. Note: You can also access the geometric adjustment screen by pressing the Geometry button on the remote control or the up arrow button on the control panel. 5. Select the H/V-Keystone setting and press Enter. Then press Enter again.
6. Use the arrow buttons on the projector or the remote control to select between vertical and horizontal keystone correction and to adjust the image shape as necessary.
7. When you are finished, press Esc. After correction, your image is slightly smaller. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. Note: You cannot combine Quick Corner correction with other image shape correction methods. 1. Turn on the projector and display an image.
3. Select the Settings menu and press Enter. 4. Select the Geometry Correction setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: Note: To reset your adjustments, press and hold the Esc button for at least 2 seconds to display a reset screen. Then select Yes.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Arc Correction You can use the projector's Arc Correction setting to adjust the curve or arc of the sides of your image.
4. Select the Geometry Correction setting and press Enter. 5. Select the Arc Correction setting and press Enter. Then press Enter again. You see the Arc Correction adjustment screen. Note: To reset your adjustments, press the Esc button for at least 2 seconds to display a reset screen, and select Yes. 6. Use the arrow buttons on the projector or the remote control to select the corner or side of the image you want to adjust. Then press Enter. 7.
1. Make sure the connected image source you want to use is turned on. 2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Search button on the remote control or the Source Search button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control.
3 Computer port source 4 Network port source (LAN, EasyMP Multi PC Projection, or Epson iProjection) 5 Screen Mirroring source (PowerLite 5520W/5530U/5535U) 6 BNC port source 7 HDBaseT port source (PowerLite 5520W/5530U/5535U) • Press the Home button on the remote control and select your image source.
Make sure that you aim the remote control at the projector's receivers within the angles listed here. 1 49 feet (15 m) 2 60° 3 30° 4 20° 5 10° 6 35° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio.
Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. Note: Set the Screen Type setting in the projector's Extended menu before changing the aspect ratio. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3.
Screen Type setting Available aspect ratios 4:3 Auto, Normal, 4:3, 6:9, Native* 16:9 Auto, Normal, Full, Zoom, H-Zoom, V-Zoom, Native 16:10 Auto, Normal, 16:9, Full, Zoom, H-Zoom, V-Zoom, Native *The image shape may differ depending on the resolution of the input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images in the same aspect ratio of the input signal. 4:3 Displays images at a 4:3 aspect ratio.
Parent topic: Using Basic Projector Features Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode.
Color Mode Description Multi-Projection Best for projecting from multiple projectors (reduces the color tone difference between images) * Available only when inputting RGB signals Note: The DICOM SIM Color Mode is for reference purposes only and should not be used to make medical diagnoses. Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1.
4. Select the Auto Iris setting and select High Speed. Note: Select Normal for quieter performance. You can turn Auto Iris on or off for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Controlling the Volume with the Volume Buttons The volume buttons control the projector’s internal speaker system or any external speakers you connected to the projector. You must adjust the volume separately for each connected input source. 1.
3. Select the Operation setting and press Enter. 4. Select the Date & Time setting and press Enter. You see a screen like this: 5. Select your date and time settings. Then select Set and press Enter to confirm your changes. 6. When you are finished, press the Menu button to exit.
Settings Options Description Daylight Saving Time Daylight Saving Time Adjusts the daylight saving time settings DST Start Daylight Saving Time: enables or disables daylight saving time DST End DST Adjustment (min) DST Start and DST End: sets the date and time to start or end daylight saving time DST Adjustment (min): sets the difference between standard and daylight saving time Internet Time Internet Time Internet Time Server Automatically adjusts the time through an Internet connection Interne
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
2. To turn the picture and sound back on, press the A/V Mute button again. Note: If you selected A/V Mute as the A/V Mute Release setting in the Extended menu, you can still control the projector while A/V Mute is enabled. Parent topic: Adjusting Projector Features Related references Projector Setup Settings - Extended Menu Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen.
Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2. Use the following buttons on the remote control to adjust the zoomed image: • Use the arrow buttons to position the crosshair in the image area you want to zoom into.
Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings. • Button lock security to block operation of the projector using the buttons on the control panel or remote control. • Security cabling to physically cable the projector in place.
Setting a Password To use password security, you must set a password. 1. Hold down the Freeze button on the remote control for about seconds or until you see this menu. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Press and hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5.
Parent topic: Password Security Types Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for about five seconds or until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On, press Enter again, and press Esc. 2.
Entering a Password to Use the Projector If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a password whenever you turn on the projector. You must enter the correct password to use the projector. 1. Press and hold down the Num button on the remote control while you enter the password using the numeric buttons. Note: The default password is 0000. The password screen closes. 2.
• If you enter an incorrect password three times in succession, you see a message telling you that the projector is locked. After the message is displayed for 5 minutes, the projector enters standby mode. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to enter the password. • If you continue to enter an incorrect password many times in succession, the projector displays a request code and a message to contact Epson Support.
2. Press the Menu button, select the Extended menu, and press Enter. 3. Select the User's Logo setting and press Enter. You see a prompt asking if you want to use the displayed image as a user's logo. 4. Select Yes and press Enter. You see a selection box overlaying your image. 5. Use the arrow buttons on the remote control or control panel to surround the image area you want to use as the User's Logo and press Enter. You see a prompt asking if you want to select this image area. 6.
You see the User's Logo zoom factor menu. 7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12. Select when you want to display the User's Logo screen: • To display it whenever there is no input signal, select Display Background and set it to Logo.
2. Select the Settings menu and press Enter. 3. Select Lock Setting and press Enter. 4. Select the Control Panel Lock setting and press Enter. Note: You can also press the left arrow button on the control panel to display the Control Panel Lock screen. 5. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 6. Select Yes and press Enter.
Locking the Remote Control Buttons You can lock some of the buttons on the remote control. To lock the remote control buttons shown here, press and hold the Home button on the remote control for approximately 5 seconds. (To unlock the buttons, press and hold the Home button again for approximately 5 seconds.) Note: If you lock the remote control buttons, you can still reset the Remote Receiver setting in the Settings menu to the default settings.
Installing a Security Cable You can install two types of security cables on the projector to deter theft. • Use the security slot on the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.
Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other. You can control the split screen feature using the remote control or the projector menus. Note: While you use the split screen feature, other projector features may not be available and some settings may be automatically applied to both images. Note: You cannot project from the same input source onto both sides (left and right) of the screen.
2. Press the Menu button. You see this screen: 3. To select an input source for the other image, select the Source setting, press Enter, select the input source, select Execute, and press Enter. (You can also change image sources, if necessary.) 4. To switch the images, select the Swap Screens setting and press Enter. 5. To change the image sizes, select the Screen Size setting, press Enter, select a sizing option, press Enter, and press Menu to exit.
Projector Identification System for Multiple Projector Control Matching the Image Colors Parent topic: Adjusting Projector Features Multiple Projector Adjustment Overview If you are combining images from multiple projectors, you can adjust the brightness and color tone difference between each image. Note: You can display a pattern to aid in adjusting the projected image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. 1.
Parent topic: Using Multiple Projectors Setting the Projector ID If you want to control multiple projectors from a remote control, give each projector a unique ID. 1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Multi-Projection setting and press Enter. 4. Select Projector ID and press Enter. 5. Press the left or right arrow buttons on the remote control to select the identification number you want to use for the projector. Then select Set and press Enter.
2. Set the remote control ID switch to On. 3. Hold down the ID button on the remote control while you press the numeric button that matches the projector's ID. Then release the buttons. Note: If you don't know the projector's ID, hold down the ID button and press the Home button to temporarily display the projector's ID on the screen. If the batteries are left out of the remote control for an extended period, the remote control ID returns to its default setting.
4. Select the Color Matching setting and press Enter. You see this screen: Note: Press Enter to toggle between the projected image and the adjustment screen. 5. Set the Adjustment Level setting to 1 and press Enter. 6. Set the remote control ID to match the second projector. 7. Access the Extended menu Color Matching setting on the second projector and set the Adjustment Level setting to 1. 8. Adjust the color tone settings for Red, Green, and Blue on both projectors in the same way. 9.
2. Press the Menu button. Note: You can also press the Memory button on the remote control to access the Memory menu directly. 3. Select the Settings menu and press Enter. 4. Select the Memory setting and press Enter. You see this screen: 5.
Parent topic: Adjusting Projector Features Adjusting the Color Tone (Color Uniformity) You can use the Color Uniformity feature to manually adjust the color tone balance in the projected image. 1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Display setting and press Enter. 4. Select the Color Uniformity setting and press Enter.
You see this screen: 5. Press Enter and select On. 6. Press Esc. 7. Select the Adjustment Level setting and press Enter. 8. Press the right and left arrow buttons to adjust the level, then press Esc. 9. Select the Start Adjustments setting and press Enter. 10. Select the area of the screen that you want to adjust and press Enter.
11. Select the color (Red, Green, or Blue) you want to adjust, and use the left arrow button to weaken the color tone and the right arrow button to strengthen the color tone. 12. Press Esc. 13. Repeat steps 10 and 11 for each area you want to adjust. 14. When you are finished, press the Menu button. Parent topic: Adjusting Projector Features Scheduling Projector Events You can save a projector command, such as turning the projector on or off or switching input sources, as an "event".
8. When you are finished, select Save and press Enter. 9. To schedule more events, repeat the previous steps as necessary. 10. Select Setup complete and select Yes to save your changes. Parent topic: Scheduling Projector Events Viewing Scheduled Events You can view any currently scheduled events. 1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Schedule Settings setting and press Enter.
1. Press the Menu button. 2. Select the Extended menu and press Enter. 3. Select the Schedule Settings setting and press Enter. You see a screen like this: 4. Press the left or right arrow buttons to highlight the date on the calendar containing the scheduled event you want to edit. 5. Press the up or down arrow buttons to highlight the event you want to edit, and press Esc. 6. Select one of the following: • On/Off: Enable or disable the selected event. • Edit: Edit the settings for the selected event.
Note: Copy the projector's settings before you adjust the projected image using the projector's Geometry Correction settings. Any saved User's Logo setting on the projector will transfer to the other projector. Caution: If the copy process fails due to a power failure, communication error, or for any other reason, Epson will not be responsible for any repair costs incurred.
2. Insert the flash drive into the wireless LAN module port. Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly. 3. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When the On/Standby and Status lights are blue, and the Lamp and Temp lights are orange, release the Esc button.
The lights flash to indicate that settings are transferring to the flash drive. When the lights stop flashing, the On/Standby light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5. Once the projector enters standby mode, remove the flash drive.
2. Insert the flash drive into the wireless LAN module port. Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be saved correctly. 3. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 4. When the On/Standby and Status lights turn blue and the Lamp and Temp lights turn orange, release the Menu button. The lights flash to indicate that settings are transferring to the projector.
Caution: Do not unplug the power cord or remove the flash drive while the lights are flashing. This could damage the projector. 5. Once the projector enters standby mode, remove the flash drive. Parent topic: Copying Menu Settings Between Projectors Related references Projector Light Status Saving Settings to a Computer You can save the projector settings you want to transfer to a computer. Your computer must be running one of the following operating systems: • Windows Vista • Windows 7 • Windows 8.
2. Connect a USB cable to your projector's Service port. 3. Connect the other end to any available USB port on your computer. 4. Press and hold the Esc button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When the On/Standby and Status lights are blue, and the Lamp and Temp lights are orange, release the Esc button. The projector shows up as a removable disk on your computer. 6. Open the removable disk and copy the pjconfdata.
The projector enters standby mode. Parent topic: Copying Menu Settings Between Projectors Related references Projector Light Status Transferring Settings From a Computer After saving projector settings to a computer, you can transfer them to another projector of the same model. Your computer must be running one of the following operating systems: • Windows Vista • Windows 7 • Windows 8.x • Windows 10 • OS X 10.5.8 • OS X 10.6.x • OS X 10.7.x • OS X 10.8.x • OS X 10.9.x • OS X 10.10.x • OS X 10.11.
2. Connect a USB cable to your projector's Service port. 3. Connect the other end to any available USB port on your computer. 4. Press and hold the Menu button on the control panel or remote control as you connect the power cord to the projector's power inlet. 5. When the On/Standby and Status lights turn blue and the Lamp and Temp lights turn orange, release the Menu button. The projector shows up as a removable disk on your computer. 6. Copy the pjconfdata.
• Mac: Drag the removable disk icon for your projector from the desktop into the trash. All the lights start flashing to indicate that the projector's settings are being updated. When the lights stop flashing, the On/Standby light turns blue and the projector enters standby mode. Caution: Do not unplug the power cord while the lights are flashing. This could damage the projector.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description White Balance Color Temp. Adjusts the overall tint of the image G-M Correction Customized Color Temp.
Setting Options Description Auto Iris Off Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Normal High Speed Normal: for standard brightness adjustment High Speed: to adjust brightness as soon as the scene changes Note: The Noise Reduction setting is not available if you have selected an interlaced (480i/576i/1080i) input signal.
Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Blanking Top Bottom Hides an area of the projected image that you select using the arrow buttons Left Right Advanced Video Range Sets the video range to match the setting of the device connected to the HDMI1, HDMI2, or HDBaseT (PowerLite 5520W/5530U/5535U) port Input Signal Specifies the signal type from input sources connected to the comput
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Power On Link Power Off Link Link Buffer Device Connections: lists the devices connected to the HDMI ports HDMI Link: enables or disables the HDMI Link function Power On Link: controls the projector or a linked device • PJ -> Device or Bidirectional: turns on the linked device when the projector is turned on •
Setting Options Description Power Consumption Normal Selects the brightness mode of the projector lamp ECO Normal: sets maximum lamp brightness ECO: reduces lamp brightness and fan noise, and saves power and lamp life Remote Receiver Front/Rear Front Limits reception of remote control signals by the selected receiver; Off turns off all receivers Rear Off User Button User1 Assigns a menu option to the User1, User2, and User3 buttons on the remote control for one-touch access User2 User3 Test Pat
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Select various options for the projector's Home screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear Ceiling Operation — See the Operation settings table in this topic A/V Settings A/V Output Selects various audio and video output settings Monitor Out Audio Settings A/V Output: select to output audio and video to an external monitor when the projector is in standby mode (Standby Mode must be turned on to use this setting) Monitor Out: select the
Setting Options Description Standby Mode Communication On Enable this setting to allow the following operations to occur when the projector is in standby mode: Communication Off • Monitor and control the projector over a network • Output audio and video to an external device (A/V Output must be set to Always On) • Communication from the HDBaseT port (Control Communications must be set to On) HDBaseT Control Communications (PowerLite 5520W/5530U/5535U) Extron XTP Selects the communication settings
Setting Options Description Multi-Projection Projector ID Select various options when projecting from multiple projectors Geometry Correction Color Mode Color Matching Color Uniformity RGBCMY Projector ID: sets the projector to a particular ID number which allows you to use a remote control to individually control projectors Geometry Correction: corrects image distortion Color Mode: adjusts the vividness of image colors for various image types and environments; select MultiProjection for all the proj
Setting Description Menu Position Selects the position of the projector menu displayed on the screen Message Position Selects the position of messages displayed on the screen Messages Controls whether messages are displayed on the screen Display Background Selects the screen color or logo to display when no signal is received Startup Screen Controls whether a special screen appears when the projector starts up A/V Mute Selects the screen color or logo to display when A/V Mute is turned on Stan
Setting Description Auto Power On If Computer or BNC is selected, the projector turns on when an input signal is detected from those ports A/V Mute Settings Adjusts the A/V Mute settings A/V Mute Timer: turns off the projector automatically if A/V Mute is enabled and 30 minutes of inactivity have passed A/V Mute Release: select A/V Mute if you want to use only the A/V Mute button to turn off A/V mute, or select Any Button to use any button to turn it off Advanced Remote Control Type: select Normal to
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Wireless LAN System Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code IPv6 Address Net.
Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Note: The lamp usage timer does not register any hours until you have used the projector for at least 10 hours. Available settings depend on the current input source.
Setting Options Description Projector Info Source Displays the name of the port to which the current input source is connected Input Signal Displays the input signal setting of the current input source Resolution Displays the resolution of the current input source Refresh Rate Displays the refresh rate of the current input source Sync Info Displays information that may be needed by a service technician Status Displays information about projector problems that may be needed by a service techni
Event ID Code List Parent topic: Adjusting the Menu Settings Event ID Code List If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the solution to the projector problem associated with the code. Event ID code Cause and solution 0020 Screen mirroring communication error occurred. Turn the projector off and then on again, or restart the network software. 0026 0032 0036 0037 0038 0021 Screen Mirroring did not start.
Event ID code Cause and solution 0433 Cannot display the transferred images. Restart the network software. 0434 Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0481 0482 0485 0483 04FE The network software quit unexpectedly. Check the network communication status, then turn the projector off and then on again. 0484 Communication with computer was disconnected. Restart the network software.
Event ID code Cause and solution 0920 The internal power supply that saves your clock settings is running low. Contact Epson for help. Parent topic: Projector Information Display - Info Menu Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All Config option on the Reset menu.
• Color Uniformity • Memory • Color Matching Parent topic: Adjusting the Menu Settings 169
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Related references Projector Light Status Cleaning the Air Filter You need to clean the projector's air filter in the following situations: • The filter or vents get dusty. • You see a message telling you to clean it. • The projector's Filter light flashes orange. 1. Turn off the projector, wait for the projector to beep, and unplug the power cord. 2. Slide the air filter cover latch and open the air filter cover.
3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter. 6. Place the air filter back in the projector as shown and push gently until it clicks into place. 7. Close the air filter cover.
Replacing the Air Filter You need to replace the air filter in the following situations: • After cleaning the air filter, you see a message telling you to clean or replace it • The air filter is torn or damaged You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1. Turn off the projector, wait for the projector to beep, and unplug the power cord. 2. Slide the air filter cover latch and open the air filter cover.
3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations. 4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover.
Related references Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover, and then remove the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. 4. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
5. Hold the lamp by its handle and gently pull it out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 6. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way.
Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 7. Push in the lamp firmly and tighten the screws to secure it. 8. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Related references Optional Equipment and Replacement Parts Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1. Turn on the projector. 2. Press the Menu button. 3.
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands.
3. Insert the batteries with the + and – ends facing as shown. 4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport, ship, or store the projector safely: • Remove any equipment connected to the projector. • Center the lens position using the vertical and horizontal lens shift dials. • Attach the protective lens pad that was included with the projector.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solving Network Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
On/Standby (power) light Status light Lamp light Temp light Filter light Status and solution Blue Blue Varies Off Off Normal operation. Blue Flashing blue Off Off Off Cooling down. All control panel buttons are disabled. Flashing blue Off Off Off Off Preparing for network monitoring or shutting down. Off Flashing blue Flashing orange Off Off Internal error. Turn off the projector, unplug it from the electrical outlet, and contact Epson for help.
On/Standby (power) light Status light Lamp light Temp light Filter light Status and solution Off Flashing blue Off Off Orange Lamp has a problem. • Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • If operating the projector at high altitude, turn on High Altitude Mode.
On/Standby (power) light Status light Lamp light Temp light Filter light Status and solution Flashing blue Varies Flashing orange Varies Varies High temperature warning. If the temperature gets too high, projection will automatically stop. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter.
Related tasks Turning Off the Projector Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Home button on the remote control. 3. Press the arrow buttons to select Help. 4. Press Enter. You see the Help menu. 5. Press the up and down arrow buttons to highlight the problem you want to solve. 6. Press Enter to view the solutions. 7.
Solutions When No Image Appears If no image appears, try the following solutions: • Press the A/V Mute button on the remote control to see if the image was temporarily turned off. • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources. • Press the projector's power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver. • Press the Menu button.
• Press the Home button on the remote control to select from a list of available sources (shown in black text). • Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary. • Check the connection from the projector to your video sources. • If you are projecting from a laptop computer, make sure it is set up to display on an external monitor. • If necessary, turn the projector and the connected computer or video source off and then on again.
Displaying From a Mac Laptop If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) 1. Open the System Preferences utility and select Displays. 2. Click the Arrangement tab. 3. Select the Mirror Displays checkbox.
Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal. • Make sure you selected the correct Screen Type setting for the screen you are using. • Try adjusting the image position using the Screen Position menu setting. • Press the Aspect button on the remote control to select a different image aspect ratio.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.
Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen, and directly in front of it. • Position the projector so the keystone adjustment angle is not so wide that it distorts the image. • Adjust the Sharpness setting to improve image quality.
• If the image has been progressively darkening, you may need to replace the projector lamp soon. Parent topic: Solving Image or Sound Problems Related concepts Projector Connections Projector Placement Projector Lamp Maintenance Related references Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Solutions to Sound Problems If there is no sound when you expect it or the volume is too low or high, try the following solutions: • Adjust the projector's volume settings.
Related references Projector Setup Settings - Extended Menu Related tasks Controlling the Volume with the Volume Buttons Connecting to a Computer for Sound Connecting to a Video Source for Sound Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Related references Projector Light Status Projector Feature Settings - Settings Menu Related tasks Turning On the Projector Unlocking the Projector's Buttons Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries.
Projector Feature Settings - Settings Menu Projector Setup Settings - Extended Menu Related tasks Installing Batteries in the Remote Control Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control. • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson.
• Connect no more than three devices that support HDMI Link at the same time. • If you have connected a speaker or receiver, set the output to PCM. Parent topic: Solving Projector or Remote Control Operation Problems Related references Projector Feature Settings - Settings Menu Solving Network Problems Check the solutions in these sections if you have problems using the projector on a network.
• For the password, enter the password set in the projector's Network menu. The default password is admin. • Make sure you have access to the network the projector is on. Note: The user ID and password are case sensitive.
projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).
Technical Specifications These sections list the technical specifications of your projector.
Brightness Normal Power Consumption mode: White light output 5500 lumens (ISO 21118 standard) Color light output 5500 lumens ECO Power Consumption mode: White light output 3700 lumens (ISO 21118 standard) Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.
Zoom ratio PowerLite 5510: (Tele-to-Wide) 1.0 to 2.0 PowerLite 5520W/5530U/5535U: 1.0 to 1.
Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 5.3 inches (134 mm) Width 18.6 inches (472 mm) Depth 12.6 inches (320 mm) Weight PowerLite 5510: 14.7 lb (6.7 kg) PowerLite 5520W/5530U/5535U: 15.2 lb (6.9 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% 4.4 to 1.
Power consumption Operating: (220 to 240 V) Normal Power Consumption mode: 411 W ECO Power Consumption mode: 309 W Standby: 2.33 W (Communication On), 0.
Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically. Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080i) 50/60 1920 × 1080 HDMI and HDBaseT*** input signals VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 WSXGA+** 60 1680 × 1050 UXGA 60 1600 × 1200 WUXGA**** 60 1920 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 7
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080p) 24/30 1920 × 1080 * Wide resolution only for PowerLite 5520W/5530U/5535U ** PowerLite 5520W/5530U/5535U only *** HDMI connection using HDBaseT transmitter for PowerLite 5520W/5530U/5535U only **** Compatible only with VESA CVT-RB (Reduced Blanking) input signal for PowerLite 5530U/5535U Parent topic: Technical Specifications 211
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Open Source Software License Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 20 inches (50 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature. • Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
No. 5 6 Symbol Approved Standards Description IEC60417 Caution, hot surface No.5041 To indicate that the marked item can be hot and should not be touched without taking care. IEC60417 Caution, risk of electric shock No.6042 To identify equipment that has risk of electric shock. ISO3864-B3.6 7 8 9 IEC60417 For indoor use only No.5957 To identify electrical equipment designed primarily for indoor use. IEC60417 Polarity of DC power connector No.
No. 12 Symbol Approved Standards Description — Positioning of cell To identify the battery holder itself and to identify the positioning of the cell(s) inside the battery holder. 13 14 15 16 17 18 IEC60417 Protective earth No.5019 To identify any terminal which is intended for connection to an external conductor for protection against electric shock in case of a fault, or the terminal of a protective earth electrode. IEC60417 Earth No.
No. Symbol 19 Approved Standards Description ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. 20 — Never look into the optical lens while the projector is on. 21 — To indicate that the marked item don’t place anything on projector. 22 ISO3864 Caution, laser radiation IEC60825-1 To indicate the equipment has a laser radiation part.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
If you desire to receive the source code of the GPL Programs, contact Epson. These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs The list of GPL Programs • busybox-1.21.0 • iptables-1.4.20 • linux-3.4.49 • patches • udhcp 0.9.8 • wireless_tools 29 • dbus-1.6.
Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail.
The list of LGPL Programs is as follows and the names of author are described in the source code of the LGPL Programs. LGPL Programs • glibc 2.17 • SDL-1.2.15 • SDL-Image • alsa-lib-1.0.27.2 • libdbus-c++-0.9.0 • grencode-3.4.2 • libnl-3.2.24 • libiconv-1.14 The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/. GNU LESSER GENERAL PUBLIC LICENSE Version 2.
change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in nonfree programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License.
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library.
The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of BSD License programs • tcpdump-4.2.1 • libpcap-1.2.1 License terms of conditions of each program which are provided by owner of the copyright to the "BSD License" are as follows. Copyright (c) The Regents of the University of California. All rights reserved. This code is derived from software contributed to Berkeley by Kenneth Almquist.
List of libjpeg programs • libjpeg-6b • libjpeg-8b License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows. Copyright (C) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software. For conditions of distribution and use, see the accompanying README file. This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us. Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as "the Independent JPEG Group's software".
List of libpng programs • libpng-1.2.49 • libpng-1.2.44 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows. This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg (88x31) and "pngnow.png" (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. Glenn Randers-Pehrson glennrp at users.sourceforge.
Jean-loup Gailly jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code. If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib". The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of newlib programs • newlib 1.17.0 License terms of conditions of each program which are provided by owner of the copyright to the "newlib" are as follows.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
(4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc. This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD. AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
Copyright 2002 SuperH, Inc. All rights reserved This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH. SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (14) Alexey Zelkin Copyright (c) 2000, 2001 Alexey Zelkin All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. (18) Citrus Project Copyright (c)1999 Citrus Project, All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Copyright (c) 2001 Mike Barcroft All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. iconv (Charset Conversion Library) v2.0 (28) Artem Bityuckiy (--enable-newlib-iconv) Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic Publishers. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (37) MIPS Technologies, Inc /* * Copyright (c) 2009 MIPS Technologies, Inc. * All rights reserved.
List of MIT License programs • jquery-1.7.2.min.js • jquery-ui-1.8.20 • jquery.ui.touch-punch.js • jquery.upload-1.0.2.min.js • jquery-1.11.3.min.js • jquery-ui-1.11.4 • expat-2.0.1 • jansson-2.4 License terms of conditions of each program which are provided by owner of the copyright to the "MIT License" are as follows. Copyright © 2012 jQuery Foundation and other contributors, http://jquery.com/ Copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
List of TOPPERS/JSP programs • jsp-1.4.3 License terms of conditions of each program which are provided by owner of the copyright to the "TOPPERS/JSP" are as follows. TOPPERS/JSP Kernel Toyohashi Open Platform for Embedded Real-Time Systems/Just Standard Profile Kernel Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of Technology, JAPAN Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory Graduate School of Information Science, Nagoya Univ., JAPAN.
Note: The TOPPERS License has been revised several times; what is shown above is the latest version that is to be applied to software made public hereafter. TINET This projector product includes the open source software program "TINET" which applies the terms and conditions provided by owner of the copyright to the "TINET". The "TINET" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of TINET programs • tinet-1.4.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (6) TINET and TOPPERS TINET (TCP/IP Protocol Stack) Copyright (C) 2001-2006 by Dep.
List of WPA Supplicant programs • wpa_supplicant-2.3 License terms of conditions of each program which are provided by owner of the copyright to the "WPA Supplicant" are as follows. Copyright (c) 2003-2014, Jouni Malinen and contributors All Rights Reserved. This program is licensed under the BSD license (the one with advertisement clause removed). If you are submitting changes to the project, please see CONTRIBUTIONS file for more instructions.
The "lighttpd" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of lighttpd programs • lighttpd-1.4.35 License terms of conditions of each program which are provided by owner of the copyright to the "lighttpd" are as follows. Copyright (c) 2004, Jan Kneschke, incremental All rights reserved.
License terms of conditions of each program which are provided by owner of the copyright to the "PCRE" are as follows. PCRE LICENCE ----------PCRE is a library of functions to support regular expressions whose syntax and semantics are as close as possible to those of the Perl 5 language. Release 8 of PCRE is distributed under the terms of the "BSD" licence, as specified below. The documentation for PCRE, supplied in the "doc" directory, is distributed under the same terms as the software itself.
Written by: Zoltan Herczeg Email local part: hzmester Emain domain: freemail.hu Copyright(c) 2009-2012 Zoltan Herczeg All rights reserved. THE C++ WRAPPER FUNCTIONS ----------Contributed by: Google Inc. Copyright (c) 2007-2012, Google Inc. All rights reserved.
FastCGI This projector product includes the open source software program "FastCGI" which applies the terms and conditions provided by owner of the copyright to the "FastCGI" The "FastCGI" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of FastCGI programs • fcgi-2.4.0 License terms of conditions of each program which are provided by owner of the copyright to the "FastCGI" are as follows.
List of OpenSSL programs • OpenSSL 1.0.2g • openssl-1.01t License terms of conditions of each program which are provided by owner of the copyright to the "openssl" are as follows. LICENSE ISSUES =========================================== The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
National Center for Supercomputing Applications University of Illinois at Urbana-Champaign http://www.ncsa.uiuc.
Copyright 1996-2002, 2006 by David Turner, Robert Wilhelm, and Werner Lemberg Introduction =========== The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license.
-------------Throughout this license, the terms `package', `FreeType Project', and `FreeType archive' refer to the set of files originally distributed by the authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project', be they named as alpha, beta or final release. `You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executable'.
These conditions apply to any software derived from or based on the FreeType Project, not just the unmodified files. If you use our work, you must acknowledge us. However, no fee need be paid to us. 3. Advertising -------------Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission.
Binding Arbitration and Class Waiver 1. DISPUTES, BINDING INDIVIDUAL ARBITRATION, AND WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS 1.1 Disputes. The terms of this Section 1 shall apply to all Disputes between you and Epson.
1.5 WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS. YOU AND EPSON AGREE THAT EACH PARTY MAY BRING DISPUTES AGAINST THE OTHER PARTY ONLY IN AN INDIVIDUAL CAPACITY, AND NOT AS A PLAINTIFF OR CLASS MEMBER IN ANY CLASS OR REPRESENTATIVE PROCEEDING, INCLUDING WITHOUT LIMITATION FEDERAL OR STATE CLASS ACTIONS, OR CLASS ARBITRATIONS. CLASS ACTION LAWSUITS, CLASS-WIDE ARBITRATIONS, PRIVATE ATTORNEY-GENERAL ACTIONS, AND ANY OTHER PROCEEDING WHERE SOMEONE ACTS IN A REPRESENTATIVE CAPACITY ARE NOT ALLOWED.
(iii) Send one copy of the Demand for Arbitration to the other party (same address as the Dispute Notice), or as otherwise agreed by the parties. b) Hearing Format. During the arbitration, the amount of any settlement offer made shall not be disclosed to the arbitrator until after the arbitrator determines the amount, if any, to which you or Epson is entitled. The discovery or exchange of non-privileged information relevant to the Dispute may be allowed during the arbitration. c) Arbitration Fees.
1.9 Severability. If any provision in this Section 1 is found to be unenforceable, that provision shall be severed with the remainder of this Agreement remaining in full force and effect. The foregoing shall not apply to the prohibition against class or representative actions as provided in Section 1.5. This means that if Section 1.5 is found to be unenforceable, the entire Section 1 (but only Section 1) shall be null and void.
accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
