SweepMOP All-In-One Cordless Self-cleaning Sweeper + Mop Model - CSM 2100 OWNER’S MANUAL Read the instructions carefully and keep for future reference
Equator assembled and operated in accordance with the written instructions with the appliance. Equator Operation eg. Using the appliance without water, using dry sponge roller Maintenance eg. Failing to remove trash and wastewater Mishandling eg. Breakage, immersing electrical components in water For Customer Service: Equator Appliances 10216 Georgibelle Drive, Suite 900D Houston, TX 77043-5249 Appliance Desk Phone/Text: 1-800-776-3538 Email: service@ApplianceDesk.com Web: www.ApplianceDesk.
Safety Please follow the safety precautions listed below: This SweepMOP is not intended for use by children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Children should be supervised to ensure that they do not play with the appliance. Stop using the SweepMOP immediately and unplug it if there is an abnormality or malfunction, including the following: The power Adapter Plug or power adapter cord is abnormally hot. The machine emits a burnt smell.
Cordless SweepMOP Powehead Assembly Power Button Handle Self-Clean Button Buttons A - Connecting Point Connecting Rod Charge Indicator Roller Replacement Indicator B - Connecting Point Lever to open/close Cover Indicator Lights Sponge Roller Powerhead Column Powerhead Cover Powerhead Roller Lock Button Docking Station Water Tank Indicator Carrying Handle Charging Column Charging Port for Adapter Plug Waste Basket Mini Brush Front View Clean Water Inlet Back View
General Instructions To prevent malfunction, please observe the following: Place the SweepMOP in an environment below 32°F (0°C) or above 122°F (50°C). Place the SweepMOP in an area away from direct sunlight and heated surfaces. Use the SweepMOP on hard surface floors, but not on carpets, rough floors or on the wall. It also should not be used for polishing floors. It cannot remove large chunks of trash and these should be cleared before using the SweepMOP for normal cleaning.
Preparation for use Charge the appliance by attaching the Adapter Plug to the magnetic port at the back of the Docking Station and plugging the other end into a 110 volt electrical outlet. Stand in front of the Docking Station and place the assembled SweepMOP straight down onto the Docking Station and ensure it locks in place on top of the Charging Column. It will charge automatically, during which time the top Indicator light on the Handle will be orange.
Operating the SweepMOP Remove the SweepMOP (with the Roller installed in it) from the Docking Station. The Handle is normally in the standing upright position. Gently place your foot on the back end of the Powerhead and pull the Handle backwards, which allows you to operate the mop easily. You will hear a click, which is the release sound of the lock. Press the top orange button on the Handle to power on. You are now ready to use your SweepMOP. Simply push to sweep and pull to mop.
Self-Clean When you have completed sweeping and mopping the floor, the SweepMOP can be easily cleaned. First, add about a gallon of clean water to the Docking Station clean water tank through the water inlet opening on top (raise Docking Station Carrying Handle to access the opening flap). The Water Tank Indicator light on the left rear side of the Docking Station will be orange if the water tank is low or empty.
Maintenance Before cleaning the Docking Station, unplug the Adapter Plug to prevent electric shock. Regularly wipe the magnetic connector on the Adapter and the charging port of the Docking Station with a dry cloth to keep it dry and clean. It is recommended that you remove and clean these parts regularly: Roller: Open the Powerhead Cover, press the orange Roller Lock Button and lift out the Roller.
If the SweepMOP will not be used for a long period of time, please turn it off after fully charging and store in a cool dry place. Please charge it at least once every three months. Replacement Parts: Sponge Roller, Brush Roller, Scraper Technical Specifications SPECIFICATIONS Powerhead Assembly size (HxWxD) 45.3 x 10.2 x 7.6 (inch) Powerhead size (HxWxD) 2.5 x 10.2 x 7.6 (inch) Docking Station size (HxWxD) 7 x 12.3 x 10.
Troubleshooting Check if the Adapter Plug is connected to the power source. Does not charge Check if there is water or foreign object on the magnetic connector of the Adapter. Please wipe it dry and clean. Check if the charging connector below the Powerhead and the charging column on the Docking Station has water residue or is covered by a foreign object. SweepMOP does not start The battery is low. Please charge it. The Roller or Roller Brush is stuck.
SweepMOP Components Included All Components packed in this box for the SweepMOP are shown below. Remove and identify each part carefully before discarding the box and packing material.
