TV Wall Mount Instruction Manual V1.0 Model: EBMT5 Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact at JKO2YU@outlook.
IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at JKO2YU@outlook.com CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
Tools Needed (Not lncluded) Stud Finder 5/32in. (4mm) Wood Drill Awl Tape Measure 3/8in. (10mm) Concrete Drill Pencil Hammer Drill Philips Screwdriver 3/8in. (10mm) 5/16 in. (8mm) Socket Wrench Wrench Supplied Parts and Hardware Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts.
TV Bolts (Only one bolt size fits your TV.) Note: The bolts are shown in accordance with the actual size D M6x15mm D1 x4 M6x35mm D2 x4 E M8x25mm E1 F M8x50mm E2 x4 x4 M4x30mm x4 F Supplied Parts and Hardware for Step 2 Bubble Level x1 Wall Plate 01 x1 Note: The lag screw is shown in accordance with the actual size A1 x4 Lag Screw ST6.3x60 mm A2 x4 Washer D6 A3 Wall x4 Anchor ø10x60mm CAUTION! These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.
Step 1 Secure the TV Brackets to TV Select TV Bolts Only one bolt size fits your TV. M4 M6 M8 Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV. Too Short Too Long Correct Correct Note: If necessary, the spacers can be used in multi-layer. If the installation fails after trying various methods, please contact customer service at JKO2YU@outlook.com.
Option B (For Round Back TV) D2/E2/F C2 (If needed) B1/B2/C1 Alternate Spacer Setups Note: Keep the arrow up Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY.
Step 2 Attach the Wall Plate [01] to Wall For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Step 2A Wood Stud Option WARNING: Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate [01]. X DO NOT USE ANCHOR [A3] FOR THIS STEP Ensure the wall plate is securely fastened to the wall before continuing to the next step.
2A-2 Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the holes. 01 2A-3 Drill 4 pilot holes using a 5/32 in.(4mm) diameter drill bit. Make sure the depth is not less than 2 23/64 in.(60mm). 2 23/64 in. (60mm) ø5/32 in. (4mm) 2A-4 Install the wall plate [01] using lag screws [A1] and washers [A2]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate [01] . 01 A1 A2 3/8 in.
Step 2B Solid Concrete or Concrete Block Option WARNING: Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate [01]. Ensure the wall plate is securely fastened to the wall before continuing to the next step. ● ● ● ● ● Mount the wall plate [01] directly onto the concrete surface Anything covering the wall must not exceed 5/8 in.
2B-3 01 A3 Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3] are seated flush with the concrete surface. A1 A2 Install wall plate using lag screws [A1] and washers [A2]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the wall plate. DO NOT over-tighten the lag screws [A1]. 3/8 in. (10mm) Socket Wrench Step 3 Secure the TV onto the Wall Plate 1. Hang the TV with TV brackets onto wall plate [01]. 2.
Step 4 Tilt Adjustment 1. Loosen the both tilt nuts [S] slightly. 2. Adjust TV to your desired tilt angle. 3. Retighten both tilt nuts [S] to fix the tilt angle. Note: Please do not over-loosen the nuts to prevent the TV from falling down.
Thank you again for choosing this product! All of us do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. If you have any questions please don't hesitate to contact us at JKO2YU@outlook.
