manual

ManualsBrandsErgotron Manualschassis components97-718-009

888-97-296-G-00 rev. C • 02/13

1 of 6

6 - 18 lbs

(2.7-8.2 kg)

6 - 18 lbs

(2.7-8.2 kg)

+B=

36 lbs (4.1-16.3 kg)

ASSEMBLY INSTRUCTIONS

Instrucciones de instalación

Notice d’assemblage

Montageanleitungen

Installatie instructies

Manuali d’Istruzione

取扱い説明書

安装说明

설치 안내

Dual Monitor and Handle Kit

ABCD E

M4 x 7mm

10x

M6 x 14mm

M5 x 12mm

3 mm

M6 x 30mm

M4 x 10mm

ID: 6.5 mm

OD: 12 mm

THK: 1 mm

IMPORTANT! This product adds an additional 6 lbs (2.7 kg) to your mounting solution. Your mounting solution's

monitor weight capacity must be reduced by 6 lbs (2.7 kg) when using standard monitors less than or equal to

2.5" (64 mm) thick. Additional reduction will be required if monitors are greater than 2.5" (64 mm) thick.

4 mm

21"-24.5"

(533-622 mm)

21"-24.5"

(533-622 mm)

M4 x 12mm

Summary of content (6 pages)

PAGE 1
Dual Monitor and Handle Kit ASSEMBLY INSTRUCTIONS Instrucciones de instalación Notice d’assemblage Montageanleitungen Installatie instructies Manuali d’Istruzione 取扱い説明書安装说明 설치 안내 21"-24.5" (533-622 mm) 21"-24.5" (533-622 mm) A 6 - 18 lbs B 6 - 18 lbs A+B= 9-36 lbs (4.1-16.3 kg) (2.7-8.2 kg) (2.7-8.2 kg) IMPORTANT! This product adds an additional 6 lbs (2.7 kg) to your mounting solution. Your mounting solution's monitor weight capacity must be reduced by 6 lbs (2.
PAGE 2
1 There are 3 ways to mount this product. Based on what mounting solution you are attaching this product to, follow the appropriate mounting instructions. A. Attaching this product to a mounting solution with 100 x 100 mm mounting hole pattern. B. Attaching this product to a mounting solution with 200 x 100 mm mounting hole pattern. C. Attaching this product to a mounting solution with a 50 x 50 mm mounting hole pattern. A/B Make sure the 'Notch' is positioned at the top of the Bow.
PAGE 3
2 2x 1x 4 mm 2x ID: 6.5 mm OD: 12 mm THK: 1 mm M6 x 30mm 3 1.5˚ 6.5˚ 8x M4 x 7mm 8x M4 x 10mm Customer Supplied 888-97-296-G-00 rev.
PAGE 4
5 1x M4 x 7mm 1x M4 x 10mm 1x M4 x 7mm 1x M4 x 10mm Center total width of mounted equipment on stand. Centre la anchura total del equipo montado en el soporte. Centrez la largeur totale du matériel monté sur le montant. Zentrieren sie die Gesamtbreite der montierten Geräte auf dem Standfuß. Centreer de totale breedte van de gemonteerde apparatuur op de standaard. Larghezza totale centrale dell'attrezzatura montata sul sostegno.
PAGE 5
6 3x 7 888-97-296-G-00 rev.
PAGE 6
8 Adjustment · Ajuste · Réglage · Einstellung · Instellen · Regolazione · 調整 · · 조절 Important! Adjust your mounting solution to handle the added weight. You will need to adjust your product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. Your mounting solution should move smoothly and easily through the full range of motion and stay where you set it.