Neo-Flex Mobile Media Center, LD with Portrait/Landscape rotation User's Guide Guía del usuario Manuel de l’utilisateur A B C 1x D E 1x 1x 4x 4x 1 M10 x 60mm 2 3 1x 1x 1x 4x 1x 1x 1x 1x 4 2x 1x M3.5 x 6mm 8x 1x 2x M6x8mm 4x 8x M5x8mm 4x 2x M3 x 37mm A A Attach Display ATORNILLE MONITOR FIXER L’ECRAN Attach Display ATORNILLE MONITOR FIXER L’ECRAN 4x M6x20mm 2x 25 - 36 lbs 25 - 50 lbs (11.3 - 16 kg) (11.3 - 22.
Holds displays with the following VESA mounting hole pattern: • 75 x 75 mm • 100 x 100 mm • 200 x 100 mm • 200 x 200 mm 20" Holds displays with the following VESA mounting hole pattern: • 200 x 200 mm • 400 x 200 mm • 400 x 400 mm • 600 x 200 mm • 600 x 400 mm 25 - 36 lbs 25 - 50 lbs (11.3 - 16 kg) (11.3 - 22.7 kg) <30 lbs <30 lbs (15 kg) (15 kg) -25˚ <5 lbs <5 lbs (2.2 kg) (2.
.2” 3.69” (80 mm) (93.7 mm) 38.4"-58.4" 38.4"-58.4" (974 - 1484 mm) (974 - 1484 mm) 64" 64" (1633 mm) (1633 mm) 9.8" 9.8" (249 mm) (249 mm) 5" 5" (127 mm) (127 mm) 16.8" 9.8" 16.8" (427 mm) 9.8" (250 mm) (427 mm) (250 mm) 29.4" 4.9" (746 mm) (124 mm) 29.4" 4.9" (746 mm) (124 mm) 17" 17" (432 mm) (432 mm) 22" 22" (559 mm) (559 mm) 42" 42" (1067 mm) (1067 mm) 23.6” (600 mm) 15.7” (400 mm) 7.87” (200 mm) 15.7” (400 mm) 17.7” 7.87” (450 mm) (200 mm) 24.
1a 1x 1x 15mm (5/8") b 4x 1x 4x 2 8x 1x 1x M3.5 x 6mm CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment. Cuidado:: No sobreapriete los tornilllos, pues podría causar un daño al equipo. Attention: ne forcez pas le serrage de la vis, cela pourrait endommager l’écran et/ou les attaches. 888-24-073-M-01 rev.
3a 2x 2x M3 x 37mm b c 2x 2x M3 x 37mm 6x 2x 4a 2x b c 888-24-073-M-01 rev.
5 4x M6x8mm 6 25 - 36 lbs (11.3 - 16 kg) 25 - 50 lbs (11.3 - 22.7 kg) 8 6 4x 7 8 1x M5 x 8mm M6 x 8mm 888-24-073-M-01 rev.
25 - 36 lbs (11.3 - 16 kg) 75x75mm 100x100mm 9 200x100mm 1 4x 200x200mm M4 x 6mm 1 4x M4 x 6mm 2 4x M4 x 6mm 3 6x 4x M4 x 12mm 2 4x 4x M6 x 14mm 6mm 6x 6mm M6 x 14mm Continue to Step 10 on page 15... 15 888-24-073-M-01 rev.
4x 2x 4x 25 - 50 lbs (11.3 - 22.7 kg) M8 x 14mm 13mm (17/32") 6 4x 200 mm M5 x 16mm 4x 200 mm 400 mm 400 mm 600 mm 600 mm 888-24-073-M-01 rev.
7a * * If a stand is already attached to your display, remove it according to display manufacturer directions. Place the display on a clean, flat, padded surface or, if you prefer, lean the display against a stable, vertical surface. Choosing Display Bracket Fasteners Notice that several sizes of screws and spacers have been provided for mounting the Tilt Mount brackets to your large display.
7b Ø b Hole Diameter Four sets of display bracket screws have been provided, each of a different diameter: 4mm, 5mm, 6mm, and 8mm. Compare the screws with the diameter of the mounting holes at the back of your display to find the same size. NOTE: Washer A is provided for use with the 4mm and 5mm screws while Washer B works with 6mm and 8mm screws. c b DIAMETRO DE LOS ORIFICIOS Se incluyen 4 juegos de tornillos para el soporte del monitor, con diferentes diámetros: 4mm, 5mm, 6mm. y 8mm.
7d Compare this measurement Compare this measurement to the recommended screw (based on display back type and diameter), taking into consideration the need for a minimum amount of thread engagement (the minimum thread engagement is the same as the diameter of the screw, for instance, the minimum thread engagement for an 8mm diameter screw is 8mm).
MM MM MM 7e Test Fasteners It is important that you test the chosen fastener combination to be sure it is the right size for your display: partially thread the screw into the display by hand with the correct combination of washers and spacers (do not fully insert and do not tighten screw at this time). If you feel resistance, remove the screw immediately and check to see if a screw with a better matching size has been provided.
7f TOP Arriba Haut y1 = y2 x < 600mm ATTACH BRACKETS TO DISPLAY f Place Display Brackets (with pre-determined fasteners) on back of display: (y) The display brackets should be centered vertically on the back of the display - the distance between the top of the bracket (y1) and the top of the display should be the same as the distance between the bottom of the bracket (y2) and the bottom of the display.
8a 2x b M4 x 16mm 9 1x 90˚ 1 2 888-24-073-M-01 rev.
25 - 36 lbs (11.3 - 16 kg) 10 25 - 50 lbs (11.3 - 22.7 kg) It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. Adjustments should move smoothly and easily through the full range of motion and stay where you set it.
11 1x a 1x M5x8mm b c 4x 2x NOTE: Leave enough slack in cables to allow full range of motion. No deje el cable excesivamente tenso Laisser du mou dans le câble d 1x 888-24-073-M-01 rev.
WARNING WARNING STORED ENERGY HAZARD! DO NOT OPEN TOWER OR REMOVE SAFETY GUARD! A primary mechanism within the tower is under tension and can be hazardous to people exposed to it under certain extreme conditions. DO NOT open the tower; DO NOT attempt to service the cart/stand. DO NOT remove safety guards or labels designed to protect or inform of possible hazards. Only Ergotron-approved installers may service or otherwise modify cart/stand.