Specifications

C
888-SV-22FN-00 rev C
3
Mounting Equipment
Autolock Drawer Tips
To Unlock Drawer - 3 methods
• Key - turn counter clockwise 1/8 turn
• Enter Master Code
• Enter Personal Code
To Program Personal Code
1 Enter Master Code
2 Press 3 and 5 simultaneously (while blinking)
3 Enter new code - any series of five numbers
To Erase Personal Code
1 Enter Master Code
2 Press 3 and 5 simultaneously (while blinking)
3 Press 1 and 2 on number pad at the same time
To Lock Drawer - 2 methods
• Press 1 and 2 on number
pad simultaneously
or
• Wait two minutes for
drawer to lock automatically
Autolock Drawer Troubleshooting
• Number pad numbers are dark
-Touch anywhere on number pad to activate back-light, (drawer remains locked until you
enter valid code)
-If touching number pad does not activate back-light, batteries may need to be replaced,
see instructions 4a.
• Number 4 on number pad is blinking = Low Voltage Warning
-Batteries may need to be replaced, see instructions 4a.
• Drawer won’t open when Personal Code is entered
-Test system by entering Master Code. If drawer doesn’t unlock,
replace batteries as instructed 4a.
Low Voltage Alert
Master Code
Master Code
New Code
Master Code
Personal Code
Manual Auto
a Lift riser to highest position and pull the key-
board/mouse tray out as far as it will go.
b Lock down lift brake.
a Apply double-sided tape to bottom of wrist rest and place on tray.
b Use hook & loop tape to  x keyboard on tray.
c Snap mouse pouch on right or left side of tray.
d Attach reference card to handle with cable tie.
5
6
Mount keyboard accessories & reference card
Route Cables
*
For optimum bonding, clean all surfaces with alcohol
wipe and allow to dry for one minute before applying tape.
Alcohol Prep
Sterile
888-24-039-00revA
2
1
3
5
4
6
1
6
3
5
2
Moving
stow - before you go
1 Look where you’re going: unlock
lift brake and lower riser for an unob-
structed view.
2 Tuck away open trays and return
mouse, scanner and other accessories
to their places.
3 Lock lift brake to keep riser down
and equipment secure while cart is in
motion.
4 Unlock both front casters.
5 Push cart from rear with elbows
bent at about 90° to maximize control
and minimize muscle strain.
6 Don’t run out!
Before moving, make sure cord is
unplugged from outlet and hooked
to basket for safe travel. Remember,
charge battery fully100% every day!
Working
customize - to your size
1 Set monitor screen about one
inch above eye level - unlock brake
to allow riser to lift or lower as shown
below.
2 Tilt screen for comfortable view-
ing and to reduce eye and neck strain.
3 Pullkeyboard tray forward and
position mouse tray and mouse pouch
on right or left, as needed.
4 Work withelbows bent at about
90° to minimize muscle strain.
5 If the riser moves up and down
with diffi culty, or if it drifts out of set
position, consult the product manual
for adjustment information.
6 Stay in charge!
Powered carts should be plugged into
outlet as often as possible to keep bat-
tery charged and computerrunning.*
Riser Lift Brake Operation
“A charged battery is a happy battery!”
4
Up = Unlocked Down = Locked
For more information on this or other
Ergotron products, visit our website:
www.ergotron.com
*
Power Cart Users: refer to the other side of this
card to learn how to respond to RUI messages about
the status of your battery charge!
a
b
c
d
*
Routing cables with the cart
components fully extended helps
ensure su cient slack for unrestricted
movement during use.
)