User guide

ManualsBrandsErgotron ManualsOffice FurnitureStyleView

1/24

StyleView® SV44 Cart

with Laptop Mount

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Deutsch

Benutzerhandbuch - Nederlands

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

888-24-300-G-00 rev. B • 10/14

ENGLISH

Features & Speci cations ............................................... 3 - 5

Set-up ............................................................................ 6 - 16

Adjustment ........................................................................ 14

Battery Charge/Discharge .................................................15

Auto-Lock Drawer ...............................................................16

Change Fuse (5 Amp) and Reset Circuit Breakers ............17

Change Power System Batteries ................................ 18 - 19

Cart Storage (long term/short term) .................................20

Ergonomics .........................................................................21

Maintenance & Safety ................................................ 21 - 24

StyleView powered carts provide electrical AC power for

mobile point of care computing equipment in a healthcare

environment. The carts are not intended to power medical

products or devices. Outlets are provided to power

information technology equipment only such as computer

equipment and computer peripherals.

For local customer care phone numbers visit: http://contact.ergotron.com

For the latest User Installation Guide and StyleLink Software Download please visit: www.ergotron.com

User Guide

Summary of content (24 pages)

PAGE 1
User Guide StyleView® SV44 Cart with Laptop Mount StyleView powered carts provide electrical AC power for mobile point of care computing equipment in a healthcare environment. The carts are not intended to power medical products or devices. Outlets are provided to power information technology equipment only such as computer equipment and computer peripherals. ENGLISH Features & Specifications ............................................... 3 - 5 Set-up ...................................................
PAGE 2
WARNING AVERTISSEMENT 14mm (9/16”) 10 °C 50 °F -20 °C - 4 °F 50 °C 122 °F Relative Humidity 5-95% rH Range Relative Humidity 5-95% rH Range Operational Storage IMPACT HAZARD! MOVING PARTS CAN CRUSH AND CUT. Failure to heed this warning may result in serious personal injury or property damage! Minimize Lift Tension BEFORE: Removing Mounted Equipment, Shipping Cart, Storing Cart. 29 °C 86 °F LEAD BATTERY This Class A digital apparatus complies with Canadian ICES-003.
PAGE 3
Features & Specifications 2 13 1 9 17 16 5 4 8 3/10 7 18 17 6 15 11 14 19 12 888-24-300-G-00 rev.
PAGE 4
ENGLISH Features & Specifications Part Number Auto-Lock Drawer SV44-1111-1 1 Drawer*/16 compartments SV44-1121-1 2 Drawers*/32 compartments SV44-1141-1 4 Drawers*/28 compartments SV44-1161-1 6 Drawers*/24 compartments SV44-1191-1 9 Drawers*/36 compartments SV44-1111-2 SV44-1111-3 SV44-1111-B 1 Drawer*/16 compartments SV44-1121-2 SV44-1121-3 SV44-1121-B 2 Drawers*/32 compartments SV44-1141-2 SV44-1141-3 SV44-1141-B 4 Drawers*/28 compartments SV44-1161-2 SV44-1161-3 SV44-1161-B 6 Drawers*/
PAGE 5
Features & Specifications Weight Capacity 20" Worksurface <5 lbs (2.3 kg) Laptop Compartment <10 lbs (4.5 kg) (508 mm) 12˚ <2 lbs (0.9 kg) see inset, below Total weight capacity per drawer. < 2 lbs (1 kg) <0.25 lbs (0.1 kg) Total weight capacity per drawer. ENGLISH Dimensions 50.5" 31" - 51" (1283 mm) (787-1295 mm) 13.4" 3.27" (340 mm) (83 mm) 3.4" (86 mm) 7.4" 2" (188 mm) (50 mm) 8.5" (216 mm) 2.5" 15.4" (64 mm) 40" (1016 mm) (390 mm) 17.2" 19.6" (438 mm) 3.7" (95 mm) 30.
PAGE 6
Set-up 1a Release Brake to move riser. CAUTION! Completely release brake engagement before raising or lowering the cart. Raising or lowering the cart with the brake partially engaged may cause product damage. ENGLISH b c 2a 6/24 d b c 888-24-300-G-00 rev.
PAGE 7
Set-up 3 Plug in power cables. If you do not have power outlets located here, then follow steps 'a' - 'd' to route power cables. a ENGLISH WARNING! Connecting electrical equipment to the outlet effectively leads to creating a medical system and the result can be a reduced level of safety. Route power cable down along tower. b-d 6' (1.8 m) 4 888-24-300-G-00 rev. B • 10/14 Power cables need to be 6' (1.8 m) long.
PAGE 8
Set-up b c 1x 1x WARNING! Connecting electrical equipment to the outlet effectively leads to creating a medical system and the result can be a reduced level of safety. ENGLISH d 4a b b 8/24 c 888-24-300-G-00 rev.
PAGE 9
Set-up 5a 1x 1x b 1x 1x 6a 1x ENGLISH b Connect Keyboard and Mouse to USB Hub USB (Type A) USB (Type A) NOTE: Bar Code Scanner should be connected directly to computer USB port. DO NOT connect Bar Code Scanner to the USB Hub. 888-24-300-G-00 rev.
PAGE 10
Set-up 7 Set up laptop boosters so the screen fits through the slot in the worksurface and the bottom of the screen is visible when the worksurface is attached. ENGLISH 822-470-00 10/24 888-24-300-G-00 rev.
PAGE 11
Set-up 8a 2x b Plug the following factory connected cables into your computer. USB: This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub and Keyboard Lights. (NOTE: Your computer must be turned on for the USB Hub and Keyboard Lights to function). Optional StyleLink: This USB cable runs from the power system to your computer for StyleLink Software. For more info on StyleLink visit: http://4support. ergotron.com . ENGLISH 1x 888-24-300-G-00 rev.
PAGE 12
Set-up 9 DO NOT OBSTRUCT AIR VENTS! Obstructing air vents may cause overheating and result in equipment damage. If computer with cables are too wide, then follow these instructions. 2 3 ENGLISH 1 4 5 10 12/24 888-24-300-G-00 rev.
PAGE 13
Set-up 11 1x a b c 1x 2 3 4 ENGLISH 1 12 a b 1x 888-24-300-G-00 rev.
PAGE 14
Adjustment 13 It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. Adjustments should move smoothly and easily through the full range of motion and stay where you set it.
PAGE 15
Battery Charge/Discharge 14 a Initial Power on/Charge Battery (takes aproximately 7 hours to charge) Plug Cart's Power Cord into wall outlet. b Turn on power system by holding power button down for 1 - 3 seconds. c With cart's power cord plugged into the wall outlet, wait until cart is at 100% charge. (takes aproximately up to 7 hours to charge) 7hrs Do Not stretch coiled cord further than 8 feet (2.5 meters), damage to the cord may occur.
PAGE 16
Auto-Lock Drawer 16 NOTE: User should change Master Personal Identification Number (PIN) upon receipt of cart. 1x Ensure that the main power system batteries are installed and functioning. The power does not need to be turned on at the power system user interface. Lost Master PIN Contact Ergotron Customer Care for instructions. All PINs may vary in length from 4 – 7 digits.
PAGE 17
How to Change Fuse and Reset Circuit Breakers 1 2 Turn off all mounted equipment. Disconnect Power System from power source. 3 Turn power system off by holding down the AC Outlet Power button for 1 - 3 seconds. Power light will shut off. 4 ENGLISH 5 5 Amp Fuse Recommended: Littelfuse 312005HXP Before reseting circuit breakers, contact Ergotron to determine cause of trip.
PAGE 18
How to Change Power System Batteries WARNING: RISK OF ELECTRICAL DISCHARGE • Do NOT swap battery cables, doing so will cause arcing and trip the circuit breaker. • Do not remove or replace the batteries while cart is located in an oxygen rich or hazardous environment, arcing may occur and cause combustion. • Replace first battery before removing second battery to reduce the risk of cables touching terminals and causing arcing.
PAGE 19
How to Change Power System Batteries 4 Caution: Do NOT swap battery cables, doing so will cause sparking and trip the circuit breaker. a b c Black Red Caution: Remove Black (-) before removing Red (+). d LEAD Recycle battery or contact Ergotron for proper battery disposal guidelines. e BATTERY f g Black h Red Caution: Connect Red (+) before connecting Black (-). 5 a ENGLISH b 6 Follow Battery Charge/Discharge Initial Power On steps a, b, c. 888-24-300-G-00 rev.
PAGE 20
Cart Storage Instructions Short Term Storage - If the Power System will be idle for up to 3 months, the battery should be fully charged before storage. Long Term Storage - If the Power System will be idle for 3 months or more, the battery should be removed from the cart and recharged during storage. Short Term Storage - If the Power System will be idle for up to 3 months, the battery should be fully charged before storage. 1 Turn off all mounted equipment.
PAGE 21
Ergonomics Working Moving customize - to your size stow - before you go 1 Set top of monitor screen about one inch below eye level - Release brake and lift or lower riser as needed. 1 During normal movement, release brake and lower worksurface to lowest position for optimal stability and unobstructed view. 2 Tilt screen for comfortable viewing and to reduce eye and neck strain. 2 Tuck away open trays and return mouse, scanner and other accessories to their places.
PAGE 22
Maintenance & Safety Cleaning and Maintenance The following procedures are not guaranteed to control infection. The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes. To avoid risk of electric shock, do not expose electrical components to water, cleaning solutions or other potentially corrosive liquids or substances. Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart.
PAGE 23
Maintenance & Safety Recommended Periodic Inspection and Maintenance Component Action How often By whom UI, Ethernet, USB cables Inspect for wear, pinching, bad connectors Monthly Any user Casters Inspect for wear and debris Monthly Any user Maximum Load Inspect to ensure that maximum recommended loads are not exceeded Daily Any user Power System SLA batteries Replace lead acid batteries1,2 It is recommended that a discharge test be conducted when cart is first purchased to determine runti
PAGE 24
Ergotron Electromagnetic Guidance and Manufacturer’s Declaration Guidance and Manufacturer’s Declaration – Electromagnetic Emissions The Powered Computer Cart is intended for use in the electromagnetic environment specified below. The customer or the user of the Powered Computer Cart should assure that it is used in such an environment. Emissions Test Compliance Electromagnetic environment – guidance RF Emissions CISPR 11 Group 1 The Powered Computer Cart uses RF energy only for its internal function.