User guide

ManualsBrandsErgotron ManualsOffice FurnitureStyleView

1 of 23

StyleView® SV44 Cart

with LCD Arm and LiFe Power System

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Deutsch

Benutzerhandbuch - Nederlands

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

888-24-310-G-00 rev. C • 10/14

ENGLISH

User Guide

StyleView powered carts provide electrical AC power for

mobile point of care computing equipment in a healthcare

environment. The carts are not intended to power medical

products or devices. Outlets are provided to power

information technology equipment only such as computer

equipment and computer peripherals.

Features & Speci cations ............................................... 3 - 5

Dimensions ...........................................................................6

Set-up ............................................................................ 7 - 16

Adjustment ........................................................................ 14

Battery Charge/Discharge .................................................15

Auto-Lock Drawer ...............................................................16

Change Fuse (5 Amp) and Reset Circuit Breakers ............17

Change Power System Batteries ................................ 18 - 19

Cart Storage (long term/short term) .................................19

Ergonomics .........................................................................20

Maintenance & Safety ................................................ 20 - 23

For local customer care phone numbers visit: http://contact.ergotron.com

For the latest User Installation Guide and StyleLink Software Download please visit: www.ergotron.com

Summary of content (23 pages)

PAGE 1
User Guide StyleView® SV44 Cart with LCD Arm and LiFe Power System StyleView powered carts provide electrical AC power for mobile point of care computing equipment in a healthcare environment. The carts are not intended to power medical products or devices. Outlets are provided to power information technology equipment only such as computer equipment and computer peripherals. ENGLISH Features & Specifications ............................................... 3 - 5 Dimensions ..............................
PAGE 2
WARNING AVERTISSEMENT 14mm (9/16”) 29 °C 86 °F 10 °C 50 °F IMPACT HAZARD! MOVING PARTS CAN CRUSH AND CUT. Failure to heed this warning may result in serious personal injury or property damage! Minimize Lift Tension BEFORE: Removing Mounted Equipment, Shipping Cart, Storing Cart. DANGER D’IMPACT ! LES PARTIES EN MOUVEMENT PEUVENT ÉCRASER ET COUPER. Il existe un risque de blessure corporelle ou d’endommagement matériel en cas de non respect de cet avertissement.
PAGE 3
Features & Specifications 2 10 17 31 5 9 4/11 17 2a 18 13 16 6 8 7 19 12 14 15 888-24-310-G-00 rev. C • 10/14 ENGLISH 1. Height Adjustable LCD Mount attaches LCDs or tablet PC's with 75x75 or 100x100mm mounting interface 2. Worksurface 2a. Worksurface Lock and Release 3. User Interface for Power System 4. Secure Storage for Laptop, Thin Client or CPU 5. Front Handle 6. Height Adjustment Brake Handle 7. USB Hub connects keyboard and mouse USB cables 8.
PAGE 4
Features & Specifications Auto-Lock Drawer SV44-1212-1 1 Drawer*/16 compartments SV44-1222-1 2 Drawers*/32 compartments SV44-1242-1 4 Drawers*/28 compartments SV44-1262-1 6 Drawers*/24 compartments SV44-1292-1 9 Drawers*/36 compartments SV44-1212-2 SV44-1212-3 SV44-1212-B 1 Drawer*/16 compartments SV44-1222-2 SV44-1222-3 SV44-1222-B 2 Drawers*/32 compartments SV44-1242-2 SV44-1242-3 SV44-1242-B 4 Drawers*/28 compartments SV44-1262-2 SV44-1262-3 SV44-1262-B 6 Drawers*/24 compartments SV44-
PAGE 5
Features & Specifications Weight Capacity <14 lbs (6.4 kg) 0 lbs (0 kg) Open Worksurface and during transport <5 lbs (2.3 kg) Closed Worksurface <13 lbs (5.9 kg) CPU Compartment 7" 60˚ (178 mm) 20" 5˚ (508 mm) 12˚ <2 lbs (0.9 kg) see inset, below 180˚ 90˚ 90˚ CAUTION: If the combined LCD and CPU weight is greater than 27 lbs (12.2 kg) then the CPU must be mounted to the rear of the cart using the Universal CPU Holder accessory (ordered separately). ENGLISH Total weight capacity per drawer.
PAGE 6
4" - 11" (102-279 mm) 50.5" 3.27" (1283 mm) 13.4" (83 mm) 3.4" 7.4" (340 mm) (86 mm) (188 mm) 8.5" 40" (1016 mm) (216 mm) 2.5" (787 mm) 15.4" 31" - 51" (64mm) 31" (390 mm) (787-1295 mm) 3.7" (95 mm) 17.5" 23" - 43" 7"- 8.5" (178-216 mm) (445 mm) (584-1092 mm) 19.75" (502 mm) 22.38" (568 mm) 15.5" 13" (330 mm) 1.75" (44 mm) 17" (394 mm) 4" 18.3" (102 mm) (465 mm) (432 mm) CPU Compartment **< 4" * (102 mm) *< 17.63" **< 2.75" (448 mm) (70 mm) < 2.
PAGE 7
Set-up 1 Release Brake to move riser. CAUTION! Completely release brake engagement before raising or lowering the cart. Raising or lowering the cart with the brake partially engaged may cause product damage. ENGLISH 2a 1x 1x b 1x 1x 888-24-310-G-00 rev.
PAGE 8
Set-up c ENGLISH 1x 3a c b Connect Keyboard and Mouse to USB Hub USB (Type A) USB (Type A) NOTE: Bar Code Scanner should be connected directly to computer USB port. DO NOT connect Bar Code Scanner to the USB Hub. 8 of 23 888-24-310-G-00 rev.
PAGE 9
Set-up 4a 0˚ 1x 0˚ M4 x 5mm b 75x75mm / 100x100mm WARNING Impact Hazard! Moving Parts can Crush and Cut. 4x M4 x 10mm ENGLISH Raise monitor to top of vertical adjustment BEFORE removing. Failure to heed this warning may result in serious personal injury or property damage! 826-504 AVERTISSEMENT Danger d’impact ! Les parties en mouvement peuvent écraser et couper. Élevez l’écran au plus haut de l’ajustement vertical AVANT de le retirer.
PAGE 10
Set-up 5 a Plug in power cables. Route power cable down along tower. If you do not have power outlets located here, then follow steps 'a' - 'd' to route power cables. 1x 1x 6' (1.8 m) Power cables need to be 6' (1.8 m) long. ENGLISH WARNING! Connecting electrical equipment to the outlet effectively leads to creating a medical system and the result can be a reduced level of safety. b WARNING DO NOT OPERATE WITHOUT GUARD IN PLACE 822-447-00 WARNING! DO NOT OPERATE WITHOUT GUARD IN PLACE.
PAGE 11
Set-up 6 Place computer and AC power adaptors in compartment. Do not place power bricks near computer or compartment air vents. a 4x 2x a 4x 4x M4 x 10mm ENGLISH b b 1x c 1x Plug the following factory connected cables into your computer. USB: This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub, Keyboard Lights and Fan. (NOTE: Your computer must be turned on for the USB Hub, Keyboard Lights and Fan to function).
PAGE 12
Set-up d Placement of CPU's in Secure Storage Area: USFF (Ultra Small Form Factor) Thin Client DO NOT OBSTRUCT AIR VENTS! Obstructing air vents may cause overheating and result in equipment damage. e Center CPU in storage area. To increase space and improve airflow, power brick may be stored under the storage area. 1 2 ENGLISH If computer with cables is too wide, then follow these instructions. f 1x 7 12 of 23 888-24-310-G-00 rev.
PAGE 13
Set-up 8 1x 888-24-310-G-00 rev.
PAGE 14
Adjustment 10 a It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. Adjustments should move smoothly and easily through the full range of motion and stay where you set it.
PAGE 15
Battery Charge/Discharge 11 a Initial Power on/Charge Battery (takes aproximately 2.5 hours to charge) Plug Cart's Power Cord into wall outlet. b Turn on power system by holding power button down for 1 - 3 seconds. Do Not stretch coiled cord further than 8 feet (2.5 meters), damage to the cord may occur. c With cart's power cord plugged into the wall outlet, wait until cart is at 100% charge. (takes aproximately up to 2.5 hours to charge) 2.
PAGE 16
Auto-Lock Drawer 13 NOTE: User should change Master Personal Identification Number (PIN) upon receipt of cart. 1x Ensure that the main power system batteries are installed and functioning. The power does not need to be turned on at the power system user interface. Lost Master PIN Contact Ergotron Customer Care for instructions. All PINs may vary in length from 4 – 7 digits.
PAGE 17
How to Change Fuse 1 Turn off all mounted equipment. 2 3 Disconnect Power System from power source. Turn power system off by holding down the AC Outlet Power button for 1 - 3 seconds. Power light will shut off. 4 ENGLISH 5 5 Amp Fuse Recommended: Littelfuse 312005HXP FUSE RATING VOLTAGE 250V CURRENT 5A OPERATING SPEED FAST-ACTING BREAKING CAPACITY 200A @ 250VAC 10000A @125VAC 6 888-24-310-G-00 rev.
PAGE 18
How to Change Power System Battery WARNING: RISK OF ELECTRICAL DISCHARGE • Do NOT swap battery cables, doing so will cause arcing and trip the circuit breaker. • Do not remove or replace the batteries while cart is located in an oxygen rich or hazardous environment, arcing may occur and cause combustion. • Replace first battery before removing second battery to reduce the risk of cables touching terminals and causing arcing.
PAGE 19
How to Change Power System Battery 4 a 5 b c Follow Battery Charge/Discharge Initial Power on steps a, b, c. Cart Storage Instructions Storage - The battery needs to be fully charged before storing and the battery must be recharged a minimum of every 90 days. 50 °C 122 °F • The recommended cart storage temperature is 25°C (77°F). At this temperature, the battery’s age-related capacity loss is minimized.
PAGE 20
Ergonomics Working customize - to your size 1 Set top of monitor screen about one inch below eye level - Release brake and lift or lower riser as needed. 2 Tilt screen for comfortable viewing and to reduce eye and neck strain. 3 Pull keyboard tray forward and position mouse tray on right or left, as needed. 4 Work with elbows bent at about 90° to minimize muscle strain.
PAGE 21
Maintenance & Safety Cleaning and Maintenance The following procedures are not guaranteed to control infection. The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes. To avoid risk of electric shock, do not expose electrical components to water, cleaning solutions or other potentially corrosive liquids or substances. Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart.
PAGE 22
Maintenance & Safety Recommended Periodic Inspection and Maintenance Component Action How often By whom UI, Ethernet, USB cables Inspect for wear, pinching, bad connectors Monthly Any user Fan on side of CPU compartment Inspect for dust at intake, vacuum as required using a vacuum cleaner that DOES NOT generate ESD (Electrostatic Discharge) Monthly Any user Casters Inspect for wear and debris Monthly Any user Maximum Load Inspect to ensure that maximum recommended loads are not exceeded Da
PAGE 23
Maintenance & Safety Ergotron Electromagnetic Guidance and Manufacturer’s Declaration Guidance and Manufacturer’s Declaration – Electromagnetic Emissions The Powered Computer Cart is intended for use in the electromagnetic environment specified below. The customer or the user of the Powered Computer Cart should assure that it is used in such an environment.