User guide

ManualsBrandsErgotron ManualsOffice FurnitureStyleView

1/29

StyleView® SV44 Telemedicine Cart

with Back-to-Back LCD and Power System

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Deutsch

Benutzerhandbuch - Nederlands

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

ENGLISH

888-24-319-G-00 rev. C • 12/14

StyleView powered carts provide electrical AC power for mobile point of

care computing equipment in a healthcare environment. The carts are not

intended to power medical products or devices. Outlets are provided to

power information technology equipment only such as computer equipment,

computer peripherals, and teleconferencing system equipment.

Components / Tools Needed ................................................................................... 2

Features & Speci cations ................................................................................................. 3 - 4

Dimensions .............................................................................................................................5

Set-up .............................................................................................................................. 6 - 21

Battery Charge/Discharge .....................................................................................................7

Adjustment .................................................................................................................... 19-20

Auto-Lock Drawer .................................................................................................................21

Change Fuse (5 Amp) and Reset Circuit Breakers ..............................................................22

Change Power System Batteries ...................................................................................23 - 24

Cart Storage (long term/short term) ...................................................................................25

Ergonomics ...........................................................................................................................26

Maintenance & Safety ...................................................................................................26 - 29

For local customer care phone numbers visit: http://contact.ergotron.com

For the latest User Installation Guide and StyleLink Software Download please visit: www.ergotron.com

User Guide

Summary of content (29 pages)

PAGE 1
User Guide StyleView® SV44 Telemedicine Cart with Back-to-Back LCD and Power System ENGLISH StyleView powered carts provide electrical AC power for mobile point of care computing equipment in a healthcare environment. The carts are not intended to power medical products or devices. Outlets are provided to power information technology equipment only such as computer equipment, computer peripherals, and teleconferencing system equipment. Components / Tools Needed ..........................................
PAGE 2
Components A D 3x 1x 1x 1x 1x 1x 2x 1x 1x M4 x 8mm 2x M4 x 12mm 2x 8x 1x 6 M4 x 8mm 1x 4x 4x 3mm 1x 12x 4 4mm 1x 1x 3 5 C 1x 1x 1 2 B 1x 1x 7 M4 x 10mm 4x ENGLISH M4 x 10mm Camera Shelf A 1 B C D 1x 1x 2 1x 1x M4 x 14mm 2x 1x 1x M4 x 6mm M4 x 25mm 4x 3 CPU Holder A B 2x 1 C 4x 8x Rear LCD Mount A B C 1x 1 4x D M4 x 10mm 4x 1x M4 x 10mm 3/32" 4x #8-32 Tools Needed 1/2" 10mm 1/2" 14mm (9/16") 2/29 888-24-319-G-00 rev.
PAGE 3
Features & Specifications WARNING AVERTISSEMENT 14mm (9/16”) 2 IMPACT HAZARD! MOVING PARTS CAN CRUSH AND CUT. Failure to heed this warning may result in serious personal injury or property damage! Minimize Lift Tension BEFORE: Removing Mounted Equipment, Shipping Cart, Storing Cart. DANGER D’IMPACT ! LES PARTIES EN MOUVEMENT PEUVENT ÉCRASER ET COUPER. Il existe un risque de blessure corporelle ou d’endommagement matériel en cas de non respect de cet avertissement.
PAGE 4
Features & Specifications IMPORTANT! This product will need tension adjustments once installation is complete. Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments. Any time equipment is added or changed on this product resulting in a different mounted weight, you should repeat the adjustment steps to ensure safe and optimum operation. This product should move smoothly and easily through the full range of motion and stay where you set it.
PAGE 5
Dimensions 14.63" (372 mm) 7" - 12" (178-305 mm) 13.4" 50.5" 3.27" (1283 mm) 3.4" (83 mm) 43" (1092 mm) 8.5" 2.5" (216 mm) (64mm) 15.4" 31" - 51" (390 mm) (787-1295 mm) (340 mm) (86 mm) 7.4" 31" (188 mm) (787 mm) 3.7" 2.9" (74 mm) 19.75" (95 mm) (502 mm) 17.5" (445 mm) 23" - 43" (584-1092 mm) 22.38" (568 mm) 13" (330 mm) 15.5" 1.75" (44 mm) 17" (394 mm) 4" (102 mm) 18.3" (432 mm) CPU Compartment *< 17.63" **< 4" (465 mm) **< 2.75" (448 mm) (102 mm) (70 mm) < 2.
PAGE 6
Set-up 1 Release Brake to move riser. CAUTION! Completely release brake engagement before raising or lowering the cart. Raising or lowering the cart with the brake partially engaged may cause product damage. ENGLISH 2a b c d 3 a b c 6/29 888-24-319-G-00 rev.
PAGE 7
Battery Charge/Discharge Set-up 4 a Initial Power on/Charge Battery (takes approximately 7 hours to charge) Plug Cart's Power Cord into wall outlet. b Turn on power system by holding power button down for 1 - 3 seconds. Do Not stretch coiled cord further than 8 feet (2.5 meters), damage to the cord may occur. c With cart's power cord plugged into the wall outlet, wait until cart is at 100% charge. (takes aproximately up to 7 hours to charge) 7 hrs 8hrs 07.
PAGE 8
Set-up 5a 1x 1x b 1x ENGLISH 1x c 1x 8/29 888-24-319-G-00 rev.
PAGE 9
Set-up 6a c b Connect Keyboard and Mouse to USB Hub USB (Type A) USB (Type A) NOTE: Bar Code Scanner should be connected directly to computer USB port. DO NOT connect Bar Code Scanner to the USB Hub. 4mm b 888-24-319-G-00 rev.
PAGE 10
Set-up 8 a 0˚ 0˚ 1x WARNING AVERTISSEMENT M4 x 5mm b 75x75mm / 100x100mm 1. 2. 4x 3. M4 x 10mm IMPACT HAZARD! MOVING PARTS CAN CRUSH AND CUT. Failure to heed this warning may result in serious personal injury or property damage! Raise monitor to top of vertical adjustment BEFORE removing. DO NOT remove Stop Screw without monitor attached. Doing so will cause monitor pivot to shoot up rapidly and may cause personal injury. DANGER D’IMPACT ! LES PARTIES EN MOUVEMENT PEUVENT ÉCRASER ET COUPER.
PAGE 11
Set-up 10 c d 1x M4 x 14mm 11 3 Mounting Options a b b ENGLISH a c d 888-24-319-G-00 rev.
PAGE 12
Set-up 11 To increase space and improve airflow, power brick may be stored under the storage area. 1x 2x M4 x 12mm a 2x b d ENGLISH c 12 Plug in power cables. WARNING! Connecting electrical equipment to the outlet effectively leads to creating a medical system and the result can be a reduced level of safety. 12/29 888-24-319-G-00 rev.
PAGE 13
Set-up 13 Place computer and AC power adaptors in compartment. Do not place power bricks near computer or compartment air vents. a 4x 2x a 4x 4x 4x M4 x 10mm ENGLISH b 1x 888-24-319-G-00 rev.
PAGE 14
Set-up c Plug the following factory connected cables into your computer. USB: This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub, Keyboard Lights and Fan. (NOTE: Your computer must be turned on for the USB Hub, Keyboard Lights and Fan to function). Optional StyleLink: This USB cable runs from the power system to your computer for StyleLink Software. For more info on StyleLink visit: http://4support.ergotron.com.
PAGE 15
Set-up 14 a 4x c 8x e ENGLISH d b 2x f g 1x 888-24-319-G-00 rev.
PAGE 16
Set-up 15 ENGLISH 16 75 mm ! M4 x 10 mm If your monitor uses a screw size other than M4 x 10mm, DO NOT use the M4 x 10mm screws or knob provided as they could result in damage to the monitor. M4 x 10 mm 4x 100 mm 4x #8-32 3/32" M4 x 10 mm M4 x 10 mm 4x 16/29 888-24-319-G-00 rev.
PAGE 17
Set-up 17 Tilt Motion Tilt monitor up and down through entire pivot range of motion. If it does not stay in place or movement in one direction is stiff, pivot needs adjustment - see below. Adjust until monitor stays in place and tilting forces, up or down, are equal.
PAGE 18
Set-up 19 Portrait/Landscape Rotate monitor from Portrait to Landscape through entire range of motion. If it does not stay in place or movement in one direction is stiff, tension needs adjustment - see below. Adjust until monitor stays in place and tension, portrait to landscape, is equal. Adjust Portrait/Landscape To Increase Tension: Turn screw clockwise. To Decrease Tension: Turn screw counterclockwise. 21 ENGLISH 1/2" 20 1x 1x 21 18/29 Keyboard Light 1. Turn Computer on. 2.
PAGE 19
Adjustment 22 a It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. Adjustments should move smoothly and easily through the full range of motion and stay where you set it.
PAGE 20
Adjustment c Lift – Up and down Follow these instructions to tighten or loosen tension. 10mm To Stop Independent LCD Lift For heavier Displays or when using a Tablet PC, you can keep the LCD Lift from moving out of position, by installing this screw into one of the three holes on the back of the riser depending on the desired height. 1x With Independent LCD Lift: 6-14 lbs (2.7-6.4 kg) Without Independent LCD Lift: 20 lbs (9 kg) ENGLISH M4 x 8mm WARNING AVERTISSEMENT 1. d 2.
PAGE 21
Auto-Lock Drawer NOTE: User should change Master Personal Identification Number (PIN) upon receipt of cart. Ensure that the main power system batteries are installed and functioning. The power does not need to be turned on at the power system user interface. 23 1x Lost Master PIN Contact Ergotron Customer Care for instructions. CAUTION: Open only one drawer at a time. Do Not push cart when drawers are open. Failure to follow these instructions may cause the cart to be unstable.
PAGE 22
How to Change Fuse and Reset Circuit Breakers 1 2 Turn off all mounted equipment. Disconnect Power System and Multiple Socket Outlet from power source. 3 Turn power system off by holding down the AC Outlet Power button for 1 - 3 seconds. Power light will shut off. ENGLISH 4 5 5 Amp Fuse Recommended: Littelfuse 312005HXP Before reseting circuit breakers, contact Ergotron to determine cause of trip.
PAGE 23
How to Change Power System Batteries WARNING: RISK OF ELECTRICAL DISCHARGE • Do NOT swap battery cables, doing so will cause arcing and trip the circuit breaker. • Do not remove or replace the batteries while cart is located in an oxygen rich or hazardous environment, arcing may occur and cause combustion. • Replace first battery before removing second battery to reduce the risk of cables touching terminals and causing arcing.
PAGE 24
How to Change Power System Batteries 4 Caution: Replace only one battery at a time. Do NOT swap battery cables, doing so will cause sparking and trip the circuit breakers. a b c Black Red Caution: Remove Black (-) before removing Red (+). d LEAD Recycle battery or contact Ergotron for proper battery disposal guidelines. e BATTERY f g Black h Red Caution: Connect Red (+) before connecting Black (-). ENGLISH 5 a b 6 24/29 Follow Battery Charge/Discharge Initial Power on steps a, b, c.
PAGE 25
Cart Storage Instructions Short Term Storage - If the Power System will be idle for up to 3 months, the battery should be fully charged before storage. Long Term Storage - If the Power System will be idle for 3 months or more, the battery should be removed from the cart and recharged during storage. Short Term Storage - If the Power System will be idle for up to 3 months, the battery should be fully charged before storage. 1 Turn off all mounted equipment.
PAGE 26
Ergonomics Moving Working stow - before you go customize - to your size 1 Set top of monitor screen about one inch below eye level - Release brake and lift or lower riser as needed. 1 During normal movement, release brake and lower worksurface to lowest position for optimal stability and unobstructed view. 2 Tuck away open trays and return mouse, scanner and other accessories to their places. 2 Tilt screen for comfortable viewing and to reduce eye and neck strain.
PAGE 27
Maintenance & Safety Cleaning and Maintenance The following procedures are not guaranteed to control infection. The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes. To avoid risk of electric shock, do not expose electrical components to water, cleaning solutions or other potentially corrosive liquids or substances. Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart.
PAGE 28
Maintenance & Safety Recommended Periodic Inspection and Maintenance Component Action How often By whom UI, Ethernet, USB cables Inspect for wear, pinching, bad connectors Monthly Any user Casters Inspect for wear and debris Monthly Any user Maximum Load Inspect to ensure that maximum recommended loads are not exceeded Daily Any user Power System SLA batteries Replace lead acid batteries1,2 It is recommended that a discharge test be conducted when cart is first purchased to determine runti
PAGE 29
Maintenance & Safety Ergotron Electromagnetic Guidance and Manufacturer’s Declaration Guidance and Manufacturer’s Declaration – Electromagnetic Emissions The Powered Computer Cart is intended for use in the electromagnetic environment specified below. The customer or the user of the Powered Computer Cart should assure that it is used in such an environment.