WorkFit-D < 65 lbs. (29.5 kg) 888-24-205-G-01 rev.
Hazard Symbols Review Symbol These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation.
WARNING! Stop screws are pre-installed in this product to secure it in the compressed position during shipping and installation. DO NOT REMOVE THESE SCREWS UNTIL INSTRUCTED TO DO SO IN THESE INSTRUCTIONS. Make sure these screws are in place before starting installation. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury.
Components 1x 1x 1x 2x 1x 2x 17x # 12-14 Wood Screw M5 x 6 mm 16x 3x 3x M2.9 x 8 mm Tools Needed 14mm 1/4” 888-24-205-G-01 rev.
Set-up Steps 1 Front Edge of Worksurface Place the worksurface on a clean floor with the top side facing down. Carefully position the leg with the hand brake on the right end of the worksurface. Place the other leg on the left end. Rear Edge of Worksurface NOTE: The brake cable is attached to both legs. Take care when removing the legs from the packaging to avoid damaging or pulling the brake cable from the legs. 2 Set the right leg (with hand brake) upright on the worksurface.
WARNING Set-up Steps 4 Keep Brake Cables Away from Sync Rod and Crossbars During Installation! Failure to keep the brake cables away from sync rod and crossbars may restrict lift motion and may cause equipment damage or personal injury! Refer to instruction manual for more information. Set the left leg (without hand brake) upright on the worksurface. Attach the left end of the rod to the left leg. 5 777-24-038-G-00 Partially insert 9 of the provided #12-14 wood screws in the left leg and worksurface.
Set-up Steps 8 3x 3x Capture the brake cable in the cable clip as illustrated, then use a Phillips screwdriver to attach the cable clips to bottom of work surface with the provided M2.9 x 8 mm screws. M2.9 x 8 mm WARNING Keep Brake Cables Away from Sync Rod and Crossbars During Installation! Failure to keep the brake cables away from sync rod and crossbars may restrict lift motion and may cause equipment damage or personal injury! Refer to instruction manual for more information.
Set-up Steps 10 Set the desk upright onto its legs. CAUTION! LIFT HAZARD! Two persons are required for this step. Failure to follow this warning may result in equipment damage and or personal injury. 11 Adjust the riser on each leg and check with a level to make sure the work surface is even. Spin Left to Raise. Spin Right to Lower. 888-24-205-G-01 rev.
Set-up Steps 12 Install all equipment before removing the 4 brake stop screws. CAUTION! Make sure you leave 20” (508mm) of slack in all cables to allow the worksurface to raise up it’s full 20” (508mm). Failure to allow enough slack in cables may cause cables to get pulled, equipment to fall off desk and may result in product damage and or personal injury.
Adjustment Step 13 IMPORTANT! This product will need tension adjustments once installation is complete. Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments. Any time equipment is added or changed on this product resulting in a different mounted weight, you should repeat the adjustment steps to ensure safe and optimum operation. This product should move smoothly and easily through the full range of motion and stay where you set it.
Adjustment Step 14 Release the hand brake (on the right leg) and move the worksurface up to highest level. Push aside the cover located behind each leg to access the adjustment point. Maintain equal amount of tension on both legs by alternating the tension adjustment from one leg to the other using a 14mm socket wrench. NOTE: The covers on the legs will not open unless the worksurface has been lifted to it’s full height. The worksurface will not lower unless the covers have been completely closed.
Set Your Workstation to Work For YOU! Configure su estación de trabajo para que trabaje para USTED. Ajustez votre station de travail en fonction de VOS besoins ! Richten Sie Ihren Arbeitsplatz so ein, dass er für SIE arbeitet! Stel uw werkstation zo in dat het voor U werkt! Approntare la stazione di lavoro nella posizione ergonomica ottimale.
