User Manual

Wireless SOHO
Installation and Operation Manual
27
2.10.2 LWS-BS Date and Time
The Base Date and Time can be set and adjusted by the User.. In the event of a power failure, the system
will retain Date and Time including Database with internal Lithium Battery. All wireless keysets registered
to the Base Station will automatically adjust Date and Time according to the Base Station value after
pressing Talk key or Speaker button.
To set the Date & Time:
1. With the LWS-BS in idle state, press the [Menu] button.
2. Select 1. CONFIGURATION > 1. DATE / TIME.
3. In this menu, set the Date and Time by entering the desired values using the keypad and scrolling
with the navigation arrow keys.
4. When finished, press the [SAVE] soft key or press the [OK] button Navigation key and a
confirmation tone will be heard.
¾ Date and Time of Wireless Keysets (LWS-WK) and Wireless Handsets (GDC-400H and GDC-
450H), are automatically updated by the LWS-BS after pressing Talk key or Speaker button
so there is no need to set the date and time on these.
2.11 Terminal Registration and Termination
The LWS-BS controls the functional service and registration related to the LWS-WK and GDC-400H/450H
including a registration function. Each LWS-WK and GDC-400H/450H must be registered to the LWS-BS (Base
Station)
before use.
2.11.1 Registering the GDC-400H/450H / LWS-WK to LWS-BS
Only one Wireless Handset or Keyset can be registered at a time.
2.11.1.1 Enabling Registrations
To enable a registration, the below procedure must be performed on the LWS-BS.
1. Press [Menu] button.
2. Press [Digit 1] (CONFIGURATION submenu), or
Select [1. CONFIGURATION] using the Navigation up/down key and then press [OK] soft but
ton or Navigation ‘OK’ key.
3. Press [Digit 4] (STATION REGISTRATION submenu), or
Select [4. STATION REGISTRATION] using the Navigation up/down key and then press [OK]
soft button or Navigation ‘OK’ key.
4. Press [Digit 1] (REGISTER STATION submenu), or
Select [1. REGISTER STATION] using the Navigation up/down key and then press [OK] soft
button or Navigation ‘OK’ key.
5. Select the phone type using the Navigation left/right key (GDC-4XX or LWS-WK)
6.
Press Navigation [OK] button or [OK] soft key.
7. Proceed to instructions below - “Registering GDC-400H/450H to the LWS-BS” or “Registering
Note:
Wireless SOHO
Installation and Operation Manual
28
LWS-WK to the LWS-BS.
8. When the registration is completed, below message is shown on the LCD of the LWS-BS.
STATION: 10X
SUBSCRIBED: SUCCESS
2.11.1.2 Registering GDC-400H/450H to the LWS-BS
To register to the LWS-BS, the below procedure must be performed on the GDC-400H/450H.
1. Press [Menu] ( , ) button to display the menu.
2. Highlight [Phone Register] in the menu using the Navigation ( ) button.
3. Press [OK] ( , ) button; then the Phone Register menu will be displayed.
4. Select [LWS Subscription] using the up and down arrows of the Navigation ( ) button
and press [OK] ( , ) button.
5. Display [Searching.1].
6. The system [RFPI : eg. 01234567890123] will be displayed when a system is found.
The RFPI of your system is available from your System Administrator, or perhaps the attend-
ant.
7. Press [OK] ( , ) button; in a few seconds, a confirmation tone will be heard at the
GDC-400H/450H.
8. If the registration fails, repeat the procedure from Step 1 to 7 at the LWS-BS and Step 1 to
7 from the GDC-400H/450H.
¾ : [Menu], [OK] button on GDC-400H
¾ : [Menu], [OK] button on GDC-450H
¾ RFPI : Radio Fixed Part Identity
¾ Seven Wireless Handsets and/or Keysets can be registered to one LWS-BS.
2.11.1.3 Registering LWS-WK to the LWS-BS
To register to the LWS-BS, below procedure is performed on the LWS-WK.
1. Press [Menu] button to display the menu.
2. Highlight [Phone Register] using the Navigation up/down key, and then press [OK] soft button or
Navigation ‘OK’ key.
3. Select [Subscription] using the Navigation up/down key, and then press [OK] soft button or
Navigation ‘OK’ key.
4. Display [Searching..1].
5. The system [RFPI : eg. 01234567890123] will be displayed when a system is found.
6. The RFPI of your system is available from your System Administrator, or perhaps the attendant.
7. Press [OK] soft button or ‘Navigation ‘OK’ key. In a few seconds, a confirmation tone is received at
the LWS-WK.
8. If the registration fails, repeat procedure from Step 1 to 7 at the LWS-BS and Step 1 to 6 from the
LWS-WK.
Note:
G