Specifications

ManualsBrandsEricsson ManualsCell PhoneA1018

GSM-DL2 GSM auto dialer

Introduction

GSM-DL2 is a GSM auto dialer; designed for car alarm, boat alarm, home alarm and other

applications. When it is triggered, it dials pre-programmed telephone numbers through a GSM mobile

phone connected. Notification can be SMS and/or voice message as programmed. The GSM mobile

phones can be used are Ericsson A1018, S868, T10, T28, T39 and T65.

J2 Wiring

+12V – Connects to 12VDC

GND – Connects to power ground

ARM – Validates the trigger input of ZL & ZH. Jumper JP2 selects H or L active for ARM input.

ZL – When the dialer is armed, applying L (0V DC, GND) to this input for over 2 seconds would

activate the dialer.

ZH – When the dialer is armed, applying H (5~12V DC) to this input for over 2 seconds would

activate the dialer.

Jumper JP2

Pin 1 & Pin 2 shorted – Applying 0V to ARM input, the dialer is armed.

Applying +12V to ARM input (or leave it open), the dialer is disarmed.

Pin 2 & Pin 3 shorted – Applying +12V to ARM input, the dialer is armed.

Applying 0V to ARM input (or leave it open), the dialer is disarmed.

Summary of content (6 pages)

PAGE 1
GSM-DL2 GSM auto dialer Introduction GSM-DL2 is a GSM auto dialer; designed for car alarm, boat alarm, home alarm and other applications. When it is triggered, it dials pre-programmed telephone numbers through a GSM mobile phone connected. Notification can be SMS and/or voice message as programmed. The GSM mobile phones can be used are Ericsson A1018, S868, T10, T28, T39 and T65. J2 Wiring +12V – Connects to 12VDC GND – Connects to power ground ARM – Validates the trigger input of ZL & ZH.
PAGE 2
Note: 1). Only when “ARM” input is active (Arm state), it validates the trigger inputs ZL & ZH, and permits listen-in from SIM card phone book tel. #1 ~ #4. 2). Only when “ARM” input is inactive (Disarm state), you can play/record voice message, Jumper JP4: JP4 is to choose the supply voltage to the mobile phone connected, and charge its battery. You have to open the top cover to change this jumper. PIN 1 & PIN 2 shorted: (factory setting) For mobile phones using 3.6V battery, such as T65, T39 and T28.
PAGE 3
Tel. number programming Before programming the mobile phone, you must do Master Reset to assure the correct default settings. Master Reset is under the menu of Settings. In addition, it’s recommended to program the tel. numbers and SMS message on the mobile phone independently, before connecting it to the GSMDL2. The contact tel. numbers must be saved in the phone book (from #1 to #7) of the SIM card (not phone memory) of the mobile phone, which connects to the GSM-DL2.
PAGE 4
3). To keep normal operation, do not change the setting on the mobile phone after successful programming. Voice recording 1). Make sure the dialer is in DISARM state, if not, disarm it first. 2). Press S3 first, and then press S4 (PLAY switch) until the RED LED lights on, release the switches, and start recording. Keep the background silent, and about 30 cm away from the dialer for speaking. 3).
PAGE 5
Dialing sequence The dialing sequence of the telephone numbers is from #1 to #7 on the phone-book of the mobile phone’s SIM card. #1 and #2 receive SMS messge only. For #3~ #7, if there is no answer in 20 seconds, the GSM-DL2 would stop calling and redial this number after 5 seconds. In case, still unanswered, it skips to dial the next telephone number.
PAGE 6
APPENDIX -A When the GSM-DL2 is connected with a car alarm, 1). Connect the “Start Disable” wire of the car alarm to the “ARM” input of GSM-DL2 Note: A). For those car alarms, whose “Start Disable” is 0V when it is armed, put the Jumper JP2 of the GSM-DL2 at PIN 1 & PIN 2 position (shorted). B). For those car alarms, whose “Start Disable” is +12V when it is armed, put the Jumper JP2 of the GSM-DL2 at PIN 2 & PIN 3 position (shorted). 2).