GDC-500H DECT Wireless Handset Quick Guide Please read this guide carefully before operating your new Wireless handset. Retain the guide for future reference.
GDC-500H Wireless Handset User Guide Important Care & Precautions: Before connecting or using your new phone, take a moment to consider safety and reliability. Use common sense when locating, connecting and using your GDC-500H. • The GDC-500H uses 3.7 VDC Li-ion batteries. Replace batteries only with identical size and type available from your local LG-Ericsson dealer. Use of a different battery type may cause damage to the phone or charger and may cause fire or explosion.
GDC-500H Wireless Handset User Guide Introduction GDC-500H is a wireless handset that employs DECT technology to provide local in-building mobility. Wireless Radio Frequencies (RF) signals are exchanged between the handset and base stations (GDC-400B / 600B/GDC-600BE). Multiple base stations connect to the Wireless Management Interface (WMI) in your LG-Ericsson phone system. The WMI links the connected base stations forming a larger Base or Zone.
GDC-500H Wireless Handset User Guide Left & Right soft button: Interactive menu displayed directly above buttons. Selection varies as needed. To select, press the soft button directly below item. 2 Talk button: Connects handset to host system to answer incoming or place outgoing calls. Recall (Flash)/Clear button: active call state=register recall, flash to regain dial tone; idle state=press to clear single digit press and hold 1 second to delete all digits.
GDC-500H Wireless Handset User Guide Batteries Quick Guide Belt Clip Ear-Microphone Installing the batteries The batteries are installed in the battery cavity in the rear of the unit. To install the batteries, 1. Remove the battery cover located on the rear of the unit. Press the latch at the top of the cover and slide the cover down to remove. 2. Insert batteries. Assure the battery polarity matches the polarity in the battery cavity. 3.
GDC-500H Wireless Handset User Guide Use only with batteries provided for the GDC-500H. Use of other types of batteries may cause harm to the unit or explosion. Dispose of used batteries in accordance with local codes and regulations. Connecting the Charger/base Unit The Charger/base unit must be connected to power using the supplied AC/DC Adapter. 1. Plug the DC output plug of the adapter into the DC input of the charger. 2. Insert the AC plug of the adapter into an AC outlet.
GDC-500H Wireless Handset User Guide Note: Use only the adapter provided with the unit. Use of a different adapter could damage the unit or cause a fire and will invalidate your warranty. It is not available to charge using USB port of PC. Installing the Belt Clip The GDC-500H comes with a belt clip that can be installed on the unit. To install the belt clip, refer to the figure and instructions below. When installing the belt clip: 1. Turn the screw clockwise on the back of the unit. 2.
GDC-500H Wireless Handset User Guide Icon GDC-500H Icons Name & Description Antenna Icon ( ) & RSSI Icon ( ) The antenna icon indicates a DECT connection is established with the Base station. The RSSI (Received Signal Strength Indicator) is a meter of the RF signal strength received by the handset. The number of vertical bars (0 ~ 4) indicates the relative strength. At less then 2 bars, call quality may not be acceptable.
GDC-500H Wireless Handset User Guide Icon Name & Description Bluetooth icon The Bluetooth is available if activation is Yes. So it allows you to use a wireless headset. Using a headset permits you to move freely around phone and maintain a conversation. Bluetooth headset icon Before using the headset, the headset must be paired with GDC-500H handset. The Bluetooth headset icon is displayed if the paring is successful.
GDC-500H Wireless Handset User Guide Message 0~9, *, #, P, D, R Description Dialed digits and special characters. (P -:Pause, D -:Go to DTMF, R -:Flash) Display Duration Dialing Subscribing the GDC-500H to a System Prior to accepting a connection with a GDC-500H, a subscription to services must be entered into the WMI of your telephone system.
GDC-500H Wireless Handset User Guide 10. If the subscription fails, repeat procedure from Step 3 to 6 at the Attendant Station and Step 1 to 8 from the GDC-500H (refer to Note). Note: Depending on the system or radio channel environment, the system or the wireless terminal may not recognize that the system has the subscribed wireless terminal or the wireless terminal is subscribed to the system. Once a user has performed the subscription procedure, the user should attempt to make a call.
GDC-500H Wireless Handset User Guide 2) 3) 4) 5) 6) steady). Press 0#. Press Flexible button 8. Enter the Station No. Press [HOLD/SAVE] button and confirmation tone is heard. Confirmation tone (or error tone) will be heard at the Station, and the corresponding Attendant Station. Authentication Verifies the wireless terminal and/or the user with the System. The User inputs the User Personal Identification (UPI) or Authorization code/PIN (5-digits), when requested by System Attendant.
GDC-500H Wireless Handset User Guide Select [1. CONFIGURATION] using Navigation up/down key and [OK] Button. 3. Press [Digit 4] (STATION REGISETR submenu), or Select [1. STATION REGISTRATION] using Navigation up/down key and [OK] Button. 4. Press [Digit 1] (REGISTER STATION submenu), or Select [1. REGISTER STATION] using Navigation up/down key and [OK] Button. 5. Select the phone type using Navigation left/right key (GDC-4XX) 6. Press Navigation [OK] button or [OK] soft key. 7.
GDC-500H Wireless Handset User Guide 2. Press [Digit 1] (CONFIGURATION submenu), or Select [1. CONFIGURATION] using Navigation up/down key and [OK] Button. 3. Press [Digit 4] (STATION REGISETR submenu), or Select [2. DEREGISTER] using Navigation up/down key and [OK] Button. 4. Press [Digit 2] (DEREGISTER submenu), or Select [2. DEREGISTER] using Navigation up/down key and [OK] Button. 5. Select phone number using Navigation left/right key (S101 ~ S107) 6. Press Navigation [OK] button or [OK] soft key. 7.
GDC-500H Wireless Handset User Guide Rejecting a Call while busy: 1. Press End button; all signaling will stop. Using Do Not Disturb (DND): 1. Press the Talk button and dial DND code (refer to system admin. or attendant); a confirmation tone is heard. 2. When finished, press the End button; the handset will return to idle state (DND OFF). Using Camp-On: 1. When calling a busy Station, press *. 2. Wait for party to answer or press End button to leave call back request.
GDC-500H Wireless Handset User Guide Delete Call Forward: 1. Press the Talk button. 2. Dial 5 + 5 +9 or 5+ 5 + 4 + #. (Confirmation tone will be heard) Call Transfer: 1. While on an active call, press the right arrow navigation button; the call is placed on hold and dial tone is received. 2. Place call to the transfer destination. 3. Remain on the line to announce the call and/or press the End button to complete the transfer. Using Call Log: 1. Press the left soft button (Menu). 2.
GDC-500H Wireless Handset User Guide User Program Codes The host system permits user control of a number of features including Temporary COS, Wake-up Alarm Clock, etc. You access the various controls through the User Program (Pgm) feature using codes. The various codes and features vary between systems; your System Administrator can provide you with available codes. The table below is an example of User Pgm codes and their use. To access a User Program: 1. Press the Talk ( ) button, you receive dial tone.
GDC-500H Wireless Handset User Guide User Pgm Code Description 42 Cancel Wake-up Alarm 51 & Msg number [xx] Set Pre-defined Msg.
GDC-500H Wireless Handset User Guide
GDC-500H Wireless Handset User Guide