Specifications

ManualsBrandsEricsson ManualsConsumer electronicsLIP-8002E

IP Phone

Quick Guide

LIP-8002E/8002AE

Please read this manual carefully before operating your set.

Retain it for future reference.

Summary of content (18 pages)

PAGE 1
IP Phone Quick Guide LIP-8002E/8002AE Please read this manual carefully before operating your set. Retain it for future reference.
PAGE 2
LIP-8002E/2AE Quick Guide ST Important Safety information To prevent the risk of harm to the user or damage to equipment, please read this information before installing or repairing the phone. 1. Only trained and qualified service personnel should install, replace or service the phone. 2. Don’t spill liquid (ex. Water) on the phone. In case of spill, contact your service technician for assistance to avoid fire or electric shock. 3.
PAGE 3
LIP-8002E/2AE Quick Guide ST Regulatory information European Union Declarations of Conformity LG-Ericsson Co., Ltd. declare that the equipment specified in this document bearing the “ CE” mark conforms to the European Union Radio and Telecommunications Terminal Equipment Directive(R&TTE 1999/5/EC), including the Electromagnetic Compatibility Directive(2004/108/EC) and Low Voltage Directive(2006/95/EC).
PAGE 4
LIP-8002E/2AE Quick Guide ST LIP-8002E/8002AE The LG-Ericsson IP phone (LIP-8002E/8002AE) is Internet Protocol (IP) phones designed to support hosted telephony services over a managed IP network. The LIP-8002E/8002AE Phone has fixed feature buttons, flexible buttons that are configurable, and dial pad buttons as shown in the figure below. Fixed Feature Button Definitions DND – Blocks all incoming calls. Toggle to activate. Speed – Access speed dialing, speed programming.
PAGE 5
LIP-8002E/2AE Quick Guide ST LIP-8002E/8002AE Keyset User Operation The following is provided as quick reference for commonly used features/functions. Complete instructions are included in the User Guide. Placing a Call: ICM Line – • Lift handset or press SPEAKER button. • Dial the extension number from the keypad. CO Line – • Lift handset or press SPEAKER button. • Press CO/IP line, or dial access number. • Dial desired phone number. Using Camp-On (Call-Wait): • When calling a busy Station, press *.
PAGE 6
LIP-8002E/2AE Quick Guide Delete Auto Call Number Redial (ACNR): • Press the REDIAL button if it has been registered as Flexible key. (iPECS-CM/MG) • When placing an outgoing call to a busy party, press the CALL BACK button. Answering a Call while idle: ICM Line – • Lift handset, or if in HF mode, just speak. CO Line – • Lift handset. (iPECS-CM/MG) • Lift handset, and press flashing Flex button (as needed). Using Do Not Disturb (DND): • Press the DND button (toggles ON and OFF).
PAGE 7
LIP-8002E/2AE Quick Guide ST Conference: A Conference flex button should be programmed. • Place a call to first member. • If first member answer, press Conf flex button and place a call to second member. • If last member answer, press Conf flex button, twice. * For conference more than 4 members in iPECS-LIK system, MCIM board is needed. (iPECS-CM/MG) • Place a call to first member. • If first member answer, press Conference flexible button and place a call to second member.
PAGE 8
LIP-8002E/2AE Quick Guide 1=Unconditional, 2=Busy, 3=No Answer, 4=Busy/No Answer , 0=Remote • For Forward code 1-4, dial destination number and press * or the SAVE button. • For Forward code 0, press * or the SAVE button. • Dial forwarded station number, password and *. • Dial the destination number. Delete Call Forward: • Lift Handset or press SPEAKER button. • Press DND button. • Dial #. (iPECS-CM/MG) • Press SPEAKER and DND button, if call forward is registered.
PAGE 9
LIP-8002E/2AE Quick Guide ST • Enter the name associated to the number. • Press the Hold button; a confirmation tone will be heard. Using Speed Dial Numbers: • Press the Speed button. • Dial the desired Speed dial bin number. LIP-8002E/LIP-8002AE Installation Note: LIP-8002E/8002AE IP-Phone can be powered by either AC adaptor or Power over Ethernet (PoE, class 1). To use AC power, use only the LG-Ericsson Approved AC power adaptor, which you can order separately.
PAGE 10
LIP-8002E/2AE Quick Guide ST Flex Button Program • Press the TRANS/PGM button. • Press the flexible button to be programmed. • Press TRANS/PGM button and User Program Code (refer to the following table). • Press the HOLD/SAVE button. (iPECS-CM/MG) 1) To assign Fixed or Number • Press the TRANS/PGM button. • Press the flexible button to be programmed. • Press program type (1: Fixed button, 2: Number, 0: Delete). • Choose the desired fixed button type (PTT, REDIAL, MUTE, CONFERENCE, ..
PAGE 11
LIP-8002E/2AE Quick Guide Code Function 33 Authorization Code (Password) Entry 34 DID Call Wait Button 35 Message Wait in Exec/Sec Pair 36 Send SMS Message 37 Register Mobile Ext. 38 Activate Mobile Ext. 39 Register Mobile Ext. CLI 41 Set Wake Up Time 42 Erase Wake-Up Time 51 Custom/Pre-defined Message Display 52 Register Custom Message (Message 00) 53 Create Conf. Room 54 Delete Conf.
PAGE 12
LIP-8002E/2AE Quick Guide ST System User Program Codes (SBG) Code Function Remark 11 Intercom Answer Mode Select ICM Signal mode, 1:HF, 2:Tone, 3:Privacy 12 Headset/Speakerphone mode 0:H, 1:S 13 Select Headset Ring type 1:S, 2:H, 3:Both 21 Set Wake-Up Time Once/Permanent & Hour/Min 22 Erase Wake-Up Time 31 LCD Display Language 32 Sys version display Domestic/English 33 Select BGM source (0~1) 34 Station Name registration Station Name 35 Display Phone IP Address 36 Display Ph
PAGE 13
LIP-8002E/2AE Quick Guide ST System User Program Codes (iPECS-CM/MG) Code Function Remark 11 Answer Mode(H/T/P) Select ICM Signal mode, 1:HF, 2:Tone, 3:Privacy 12 Station Name Program Input up to 12 characters iPECS-CM: Index(1-5) + Type(1~5, 1:Once, 2:Daily, 3:Mon~Fri, 4:Mon~Sat, 5:Date), + HHMM(24-hour clock) + 13 Set Wake Up YYMMDD(If type is Date) iPECS-MG: HHMM(24-hour clock), # (repeat mode: once, repeat) iPECS-CM: Index(1-5) 14 Reset Wake Up iPECS-MG: 1:ON/OFF, 2:Ring Delay (0-9) 15
PAGE 14
LIP-8002E/2AE DKN Funktionstaster FORSTYR EJ – Blokerer for indkommende kald. VOLUMEN   – Justerer lydniveauet for ringe tone, headset, og håndfri, samt justerer display kontrast (når telefonen er ledig). OMST/PROG – Omstillingstast. Anvendes til omstilling af kald og programmering. HOLD/GEM – Anvendes til at parkere samtaler, samt gemme programmeringsinformation. MIKROFON – afbryder/tilslutter mikrofonen HÅNDFRI – Besvarer kald uden brug af telefonrøret.
PAGE 15
LIP-8002E/2AE DKN Kort brugervejledning Dette er en kort brugervejledning. Yderligere information findes i brugervejledningen. Foretage et opkald: Til et lokalnummer –  Løft røret eller tryk på HÅNDFRI tasten.  Tast lokalnummeret på tastaturet. Til et telefonnummer –  Løft røret eller tryk på HÅNDFRI tasten.  Tast 0, eller tryk på en LINIE taste.  Tast det ønskede telefonnummer. Benyt Banke-på ved kald til optaget lokalnummer:  Når man hører at lokalnummeret er optaget taster man * og afventer svar.
PAGE 16
LIP-8002E/2AE DKN Sæt te samtalen på HOLD:  Tryk på HOLD/GEM tasten under samtalen.  Tryk på LINIE tasten for at genoptage samtalen. Konference:  Foretag det første opkald.  Tryk på KONF. tasten.  Foretag det andet opkald.  Tryk på KONF. tasten to gange. Viderestillinger:  Løft røret.  Tryk på FORSTYR EJ tasten.  Tast koden for at vælge type af viderestilling (0-5).
PAGE 17
LIP-8002E/2AE DKN Programmering af Flextaster     Tryk på OMST/PROG tasten. Tryk på den Flextaste der ønskes programmeret. Tryk på OMST/PROG tasten og tast bruger program-koden (se tabellen herunder). Tryk på HOLD/GEM tasten. System Bruger Program-koder Kode 11 12 13 14 15 19 21 22 23 30 33 34 35 36 37 38 39 41 42 Funktion Ringetone ved interne kald Ringtone ved indkommende kald Svar indstilling ved lokale kald.
PAGE 18
LIP-8002E/2AE DKN System Bruger Program-koder (fortsat) Kode 51 52 53 54 55 61 62 71 72 73 74 75 76 77 79 80 84 85 86 87 88 91 94 95 96 97 98 99 Funktion Aktiver forudbestemt besked Opret brugerdefineret besked (besked nr.