Instructions / Assembly

Lay erod
TM
on a flat surface with keyed slot
facing upward. Insert motor assembly into
keyed slot on rod end. Twist until gears are
engaged and motor is seated into erod
TM
(lock button should align with stationary clip
on end of rod). Slide lock button towards rod
to lock motor assembly into place.
Find closest electrical outlets to window and
decide which side of window to orient motor.
(Battery Power Kit sold separately for use
without wall adaptor.)
Extend rotating side brackets on erod
TM
toward wall and align ends of erod
TM
to outer
edges of window. Using level and rotating
side brackets, mark desired side and center
mounting plate locations.
Align top of mounting plates to marked
positions and mark hole positions. Make
sure all 3 mounting plates are at the same
horizontal level.
(NOTE: Some installations require special
attachment methods and anchors. Only
drywall anchors are supplied.)
Drill anchor holes with
3
/
16
inch drill bit and
insert wall anchors. Attach mounting plates
to wall using screws provided.
Slide “L” supports onto mounting plates. Place center bracket clamp near middle of
erod
TM
and insert all three brackets into
“L” supports on wall. Pinch center clamp
tight onto rod and lock into place with top
set screw.
Determine the projection of the erod
TM
from
the wall, then insert and tighten bracket set
screws on bottom of all 3 brackets to secure.
Place rod set screw in middle hole (of the
three on top of rod). Use a coin to tighten
rod set screw.
Plug wall adaptor into electrical outlet.
Use cord guides to secure cord to wall.
To set center drapery position:
[a] Press < l > button to open erod
TM
to its
outermost position (only one carrier will move).
[b] Slide loose carrier to outermost position
(away from the motor) and tighten both carrier
screws to lock in place. Press > l < button and
close erod
TM
to its center position. The center
drapery position on your erod
TM
is now set.
In the closed position, start from each end
of erod
TM
, attach drapery panel(s) using clips
(or remove clips and attach pin hooks, sold
separately). Work your way towards the
center of rod, distributing clips or hooks evenly
as you go. Overlap panels for privacy.
(Additional roller clips sold separately.)
Clip remote sensor to front of panel (hiding
cord behind drapery).
FOR QUESTIONS OR CONCERNS, CALL
CUSTOMER SERVICE AT 1-877-695-8268,
8 AM-5 PM, PST, MONDAY-FRIDAY.
REMOTE
SENSOR
3
J
4
B
6
B
C
7
C
C
C
J
D
J
2
11
1
LOCK
BUTTON
E
5
BG
10 12
I
Care Instructions: Clean with a soft cloth. Do not use abrasive cleaning agents,
solvents, or polishes as they may damage the finish.
Estimated Assembly Time: Approximately 30 minutes
Tools Needed (not included): Drill with
3
/
16
in drill bit, Phillips screwdriver,
Level (recommended)
How to Measure: To determine the appropriate drapery rod length, use a
metal measuring tape to gauge the outside width of the window to be covered.
Align ends of erod
TM
to outer edges of window.
motorized
drapery hardware
CENTER OPEN CONFIGURATION
BEFORE INSTALLATION, UNPACK BOX AND LAY OUT CONTENTS:
M
B
C
D
X 1 erod
TM
w/ Integrated Drapery Clips
X 3 Mounting Plate
X 3 “L” Support
X 1 Center Bracket Clamp
X 1 Motor Assembly
X 1 Remote Control
X 6 Mounting Hardware
X 1 Wall Adapter w/ 12 ft Cord
X 1 Remote Sensor (attached to motor)
X 2 Rotating Side Bracket (attached to rod)
X 3 Bracket Set Screw
X 10 Cord Guides
X 1 Rod Set Screw
E
F
G
H
J
K
A
I
L
9
H
L
8
K
K
M
K