user manual

ManualsBrandsEscalade Sports ManualsFitness EquipmentFitness Equipment B2304E

1. Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons

before assembling or ordering parts.

3. To make assembly of your basketball system easier, use the Hardware Identifier on page 3 to

identify and sort all fasteners. Check all cartons for kits. All hardware is not located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to

tighten them.

OWNER'S MANUAL

MODEL NO.

B230B230

B230

4E4E

Goalrilla V

BASKETBALL SYSTEM

Please Do Not Return This Product to the Store!

Contact Escalade

Sports customer service department at:

Phone: 1-888-USA-GOAL Toll – Free !

Fax: 1-866-873-3536 Toll – Free !

E-mail: basketball@escaladesports.com

Mailing Address:

Escalade Sports

PO Box 889

Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE®

SPORTS PRODUCT INFORMATION

2L-6633-03

Escalade® Sports products may be manufactured and/or licensed under the following patents.

6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128

Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

Summary of content (10 pages)

PAGE 1
MODEL NO. B230 4E Goalrilla V BASKETBALL SYSTEM OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering parts. 3. To make assembly of your basketball system easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for kits. All hardware is not located in one kit. 4.
PAGE 2
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • • • • • • Do not dunk on this unit Do not hang from any part of the unit, including the backboard, rim, support braces, or net. Do not slide, climb, or play on pole. Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and /or deterioration.
PAGE 3
PAGE 4
INST ALLA TION TIMELINE INSTALLA ALLATION 1. Prior to anchor system and goal assembly, call utility services for location of underground utility lines before you dig. 2. Vertical main post assembly is a two part process. PART 1 Complete Anchor System Installation Instructions. (Below) Day 2-4. Allow concrete to cure. Day 1. Day 5. PART 2 Complete GoalrillaT M assembly instructions.
PAGE 5
ASSEMBL Y INSTRUCTIONS (Day 5) ASSEMBLY IMPORTANT! Nylon washers (#5) adequately space painted parts at all pivot points. Neglecting the use of these washers will result in rusted parts. NOTE: All board arms are made of rectangular tubing. Tightening hardware too tight may damage tubing and make adjustment of system difficult. 1. Slide Right Post Ear (#44) and Left Post Ear (#45) behind bracket on back of Post Assembly (#2).
PAGE 6
7. Secure Actuator (#16) to Lower Arms (#11) using one bolt (#7), two flatwashers (#3), four plastic washers (#5) and one hex nut (#4). See Figure 6. Tighten both bolts (#7) securing Lower Arm (#11). Note: Tighten bolts snug but, do not over tighten. Board Arms must pivot freely freely.. Figure 6 8. Insert four Tube Plugs (#9) into open ends of Lower Arms (#11). It may be necessary to use a hammer or rubber mallet to tap them in. 9.
PAGE 7
A TT A CHING BA CKBO ARD T O BO ARD ARMS TTA BACKBO CKBOARD TO BOARD REQUIRES A T LEAST FOUR CAP ABLE ADUL TS AT CAPABLE ADULTS TS.. 15. With at least three capable people, raise the backboard assembly up and have the fourth attach Lower Board Arms to lower mounting tubes on backboard using two bolts (#20), four Board Bushings (#22) (shipped already installed), two spacers (#8), two plastic washers (#5), two washers (#3) and two hex nuts (#4). See Figure 10. Note: Do NOT over tighten these bolts.
PAGE 8
LIMITED LIFETIME WARRANTY This consumer warranty extends to the original consumer purchase of any Escalade® Sports Product (hereinafter referred to as the “Product”). WARRANTY COVERAGE: Escalade® Sports warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship.
PAGE 9
CARE INFORMA TION INFORMATION BACKBOARD CARE AND MAINTENANCE Items needed to clean backboard: • 100% cotton soft cloth, (only) • Mild dish washing liquid for soap • Luke warm water • Mild plastic polish to minimize scratches Rinse backboard with lukewarm water. Wash gently with a 100% Cotton soft cloth, lukewarm water and mild soap. Do not scrub. Rinse backboard with lukewarm water again. Dry with 100% cotton soft cloth.
PAGE 10
2L-6633-03