Table Top Game User Manual

ManualsBrandsEscalade Sports ManualsGameP1225LGRL 527.25155

OWNER'S MANUAL

CHAMPION 8 FT. DROP POCKET POOL TABLE

MODEL NO. P]225LGRL 527.25155

MODEL NO. P]227LGRLA 527.25165

1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY.

Read each step completely before beginning each step.

2. SOME SMALLER PARTSMAY BE SHIPPED INSIDE LARGER PARTS.CHECK INSIDE ALL PARTS

AND CARTONS BEFORE ASSEMBLING OR ORDERING PARTS.

3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND SORT ALL FASTENERS. CHECK ALL CARTONS

FOR KITS. ALL HARDWARE IS NOT LOCATED IN ONE KIT.

THIS TABLEISCONTAINED IN THREESEPARATECONTAINERS:

PLEASE DO NOT RETURN PRODUCT TO THE STORE!

Contact Escalade® Sports customer service department at:

Phone: 1-866-556-2757 Toll Free !

Fax: 1-866-873-3532 Toll Free !

E-mail: billiardtables@escaladesports.com

Mailing Address (Correspondence Only):

Escalade® Sports, PO Box 889, Evansville, IN 47706

Please visit our World Wide Web site at:

www.escaladesports.com

On-Line Trouble Shooting Frequently Asked Questions

Technical Assistance On-Line Parts Requests

Additional Escalade® Sports Product Information

ESCAI.ADE

S P 0 R T S

Escdade® Spots products may be manufactured and/or licensed underthe following patents.

D446275

Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2L-6860-00

@2004 Escalade Sports

Summary of content (16 pages)

PAGE 1
OWNER'S CHAMPION MANUAL 8 FT. DROP POCKET POOL TABLE MODEL NO. P]225LGRL 527.25155 MODEL NO. P]227LGRLA 527.25165 1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY. Read each step completely before beginning each step. 2. SOME SMALLER PARTSMAY BE SHIPPED INSIDE LARGER PARTS.CHECK INSIDE ALL PARTS AND CARTONS BEFORE ASSEMBLING OR ORDERING PARTS. 3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND SORT ALL FASTENERS. CHECK ALL CARTONS FOR KITS. ALL HARDWARE IS NOT LOCATED IN ONE KIT.
PAGE 2
CAUTION THE SPRAY ADHESIVE PRESSURE! CHILDREN! AREA MUST USED CAREFULLY DO NOT FOR APPLYING READ CAUTIONS ON PLAYFIELD CLOTH SPRAY ADHESIVE IS EXTREMELY CONTAINER! FLAMMABLE KEEP OUT USE OR STORE NEAR HEAT SOURCE ! FLAMES ! SPARKS OR WHEN BE WELL VENTILATED. OPEN DOORS AND WINDOWS t.IMPORTANT WHEN USING AND UNDER OF THE REACH OF SMOKING! WORK SPRAY ADHESIVE. t. THE DRAWINGS IN THIS MANUAL MAY BE EXAGGERATED OR MOlTO SHOW DETAILS.
PAGE 3
ASSEMBLE TWO LEG PEDESTALS AS FOLLOWS: 1. Begin by opening hardware kits and sod hardware. Remove the mounting plate from one leveler #22 and attach it to bottom of left leg # 19 using two screws #27 and two dowel connectors #26. Cover holes with adhesive hole covers #28. See Figure t. Screw leveler #22 back into mounting plate. 2. Repeat for other left leg #19 and two right legs #20. 19&20 Covered holes should face inward. Use \ 21 holes 3.
PAGE 4
0 5O 15 WARNING Holes marked by arrows MUST be on the TOP when attached to leg pedestals. 4O 5o 15 5. Attach beam # 15 by using four bolts #40, eight washers #50, and four tocknuts #49 for each of the leg mounting location. Place one washer between the bolts and beam and one between leg posts and tocknuts. Tighten these bolts securely. (See figure 4) 6. Attach other beam # 15 to the other side the same way.
PAGE 5
Detail A NOTE: Screwheads should be flush with or below the top of the slats #16 and #17. ,8H 36 15\ Slot should be straight up and down Hole for dowel connector #36 is closer to the top of beam. 16 9. Place long slats #16 (50 inches long) and short slats # 17 (36 inches long) across table from beam to beam as shown in figure 6. Make sure to use the two shorter slats #17 on the ends of the beams and the two longer slats #16 in the center as shown.
PAGE 6
LEVELING BASE FRAME 11. Using a carpenter's level, leveltable aswell as possible. It iseasier to do it now rather than after the slate is on frame. Determine the highest corner of the fra me. Raise other three corners to the level of the highest corner by shimming underneath legs using playing card stock or grey leg shim stock (#47) shipped with this table. Cut this shim stock and place under legs (#20).
PAGE 7
¢AUTION: Be sure that the side of the play surface with the _oles faces up. 16 17 DETERMINE THE TOP SIDE OF THE PLAY SURFACE! IMPORTANT: Be sure countersunk holes in all three table top sections #9 and # 10 face up: See Figure 10. NOTE: Slatron tables have "match" Iine markings like those shown above (letters A, B, C). Line up these lines when putting clown the statron sections. 14. 15. 16. Place center section #10 on Center this piece on slats as section # 10 should overhang inch.
PAGE 8
SHIMMING General INSTRUCTIONS Top of playing surface must be flush at seams! Rules • Accomplish possible. the leveling of slate with as few shims as • Slate is brittle. Do not tap with a hammer or tiqhten screws unreasonable tight. You will not be abqe to compress the slate. You must shim up the slate to level. Shims #38 are meant only to raise the low places at the seams and ends. Very sho4 and low places should be grouted. Do not assume the floor is level.
PAGE 9
WARNING: Application First Glue Applying the cloth 22. Make sure slate/slatron is dry and free of dust. Spray glue on edge of slate too. NOTE: Before spraying adhesive, cut a podion of the shipping cation to use as a shield to prevent cement overspray. 23. Place cloth over slate/slatron with equal overhang on all sides. NOTE: Cloth may seem small but it will stretch a great deal. 24. Fold cloth away from end to expose slate/slatron for your first glue application.
PAGE 10
| I I identify the rails. Side caps must be installed before the rails are attached This view isCorner shown caps without side and corner to help I to slate. will be installed after caps area installed is established, 2 3 \ \ Slate 4'---4 4 --_-lb- Look along the front edge of the side rails to be sure they align. Side rails must be in a straight line with each other, ! ! 3 2 0 34, Attach side caps #7 to one side rail (either #2 or #3) as shown in figure 18. Use two nails #41 per side cap #7.
PAGE 11
38. AlCachend aprons # 12 to recessedarea on the underneath side of the end rails (#4). CENTER THE APRONS WITHIN THE LENGTH OF THE RAILS. Hold apron in place and spot the location of the mounting holes on the rails. Punch pilot holes in rail using an awl (or 8d nail) and hammer. This will require the help of another person. Secure aprons to rails with screws #45. (See Figure 20) NOTE: To help drive screws into rails, put a lil¢ledry soap on threads of screw. 39.
PAGE 12
41. Before attaching the drop pockets to the rails you will need to tri mtwo of them to fit into the side pockets. (See figure 25) Inserhhe corner and side drop pockets (thetwo that you have trimmed) into the drop pocket openings on the table. THE LIP ON THE POCKETS GO INTO THE RECESSED AREA ALONG THE INSIDE RIM OF THE CORNERAND SIDE CAPS. Trim drop pockets if necessary to assure a snug fit. Corner drop pocket] Trim as necessary. front edge shown here. J \ 41 \ 42.
PAGE 13
ONE YEAR LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADE® SPORTSProduct (hereinafter referred as the "Producf_). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of one (1) year from the original purchase.
PAGE 14
! I I_q_ _! II 2 1 822-3 PLAYFIE LD SPOTS 2A-7053-07 LEG PANEL 2 2A-4049-57 TOP RAIL LEFT SIDE 4A-6957-00 LEVELER (SET OF 4) 1 3 2A-4050-57 TOP RAIL RIGHT SIDE 3M-6194-00 DROP POCKET 6 4 2A-4051-57 TOP RAIL END 801-32 ,_4X 5/8" SCREW 5 5A-6827-00 SIGHT PLUG KIT 7B-6314-00 ,_10-24 6 3M-6522-00 CORNER 7 3M-6523-00 SIDE CAP 4L-7717-01 HOLE COVER 8 3M-6546-00 CORNER POST 5A-6670-50 PLAYFIELD CLOTH 1 9 809-551 SLATE PLAYFIELD END 801-77B ,_10 X 2" SCREW 18 2W-6
PAGE 15
18\ 17. 10 3 _9 36 o 17 ...... NOTE: Not all parts are shown. Also see page 16.
PAGE 16
8_ 20 45 26 21 45 r_ i C>. oo C_ Q Q NOTE: Not all parts are shown. Also see page 15.