05.01.2016 V.1 Equipment Supply Company Instruction Manual miniLIFT CLASSIC -Mobile Lift MODEL 92050 SCAN THIS QR CODE TO WATCH THE LIFT & MOVE miniLIFT or Go to YouTube “EquipmentSupplyCo” Copyright © 2016 Equipment Supply Co.
miniLIFT - Mobile Lift System - MODEL #92050 MANUFACTURER’S INTRODUCTION ESCO has carefully produced this instruction manual. It is a condition that before the installation and first use of the miniLIFT, the instruction manual, must be read by the operator. The manual is an essential part of the miniLIFT CLASSIC [Model 92050], which requires proper maintenance during the working life of the lift.
miniLIFT - Mobile Lift System - MODEL #92050 GENERAL CHARACTERISTICS miniLIFT is a vehicle lift is made with a folding structure and driven by two air bags. This vehicle lift has been developed for body shops to lift the side or the front or rear wheels of vehicles, according to the needs. The lift must only be used to lift a vehicle with the same or inferior weight as the max weight allowed. Capacity of load indicated in this manual and on the unit 5,500 lbs. (equivilant to 2.500 KG noted on the unit).
miniLIFT - Mobile Lift System - MODEL #92050 Technical characteristics and dimensions table miniLIFT DIMENSION UNIT VALUE Maximum load capacity Lbs. 5500 Maximum height above the ground In. 21.65 Minimum height above the ground In. 5.25 Width of platform In. 24 Length of platform In. 54.4 Weight of unit with accessories Lbs. 55 Required PSI Min-Max 100 -115 PSI Rise time sec. 13 Descent time sec. 17 Measures support arm In. see chart Chart of machine dimensions 4 1.800.
miniLIFT - Mobile Lift System - MODEL #92050 PACKAGING AND TRANSPORT All parts of the miniLIFT will be sent on a single pallet: When opening the packaging, check that all the components are present. The check is to be done in the presence of the carrier, to see if a component is lost. ESCO is not responsible for any damage due to transportation, loading, unloading and unpacking.
miniLIFT - Mobile Lift System - MODEL #92050 Pneumatic circuit connection Initially the lift is not connected to the operating control. The lift connects to the compressed air network using a fast connector, but only when it is in the neutral position, which is the default position. The functioning of the operating control will be explained later in the manual. Install Air Nipple (1/4 INCH NPT) into handle using teflon tape (or equivalent).
miniLIFT - Mobile Lift System - MODEL #92050 IMPLEMENTATION AND VERIFICATION The lift has to be connected to the inlet air line through the quick plug, and the operating control has to be connected to the compressed air network of the workshop. Check that the pressure needed to operate the lift is correct, between 100-115 PSI. LIFTING OPERATION OF MINILIFT After this check it has to be verified if the functioning of the lift is correct.
miniLIFT - Mobile Lift System - MODEL #92050 After having positioned the mobile lift under the vehicle, make sure that the lift is within the width of the vehicle. Once that is done, the arms have to be lengthened until the rubber pad is situated below the point indicated for lift (where the jack is normally situated). The arms must not be extended beyond the “stop” point indicated on the arms. The rubber pads are adjustable in height, and have different positions.
miniLIFT - Mobile Lift System - MODEL #92050 WARNING: ESCO will take no responsibility neither civil, criminal or any injury to person that may occur. WORKING POSITION After the lifting operation, before proceeding with the work, the stability of the vehicle on the lift has to be tested. When work will be carried out beneath the vehicle additional means of support such as two axle stands must be used. miniLIFT unit comes complete with (2) Support Stands (lifting capacity of 2,750 lbs per stand).
miniLIFT - Mobile Lift System - MODEL #92050 PROPER INSTALLATION OF SUPPORT STANDS All loads MUST BE SUPPORTED by an appropriate support system. The miniLIFT is NOT a support system It is designed to lift the load, NOT maintain the weight. The proper use of support stands MUST be applied to the load for proper usage of the miniLIFT system. The miniLIFT system comes with (2) 2,750 lb. capacity per support stand [5,500 lb.
miniLIFT - Mobile Lift System - MODEL #92050 This instruction manual should be read carefully before use and application of each of the functions of the lift. It is forbidden to use the lift to lift people. Before the up and down operation, always make sure that the structure is free from any kind of objects or tools. Always carefully control the load, especially in up load phase, ensuring that the maneuver is being performed correctly.
miniLIFT - Mobile Lift System - MODEL #92050 WARRANTY The miniLIFT carries a 3-YEAR warranty on all parts, provided there has not been any tampering or changes to any original part of the lift. For the warranty to be valid it is necessary to register your product through ESCO along with maintaing and keeping this manual.
miniLIFT - Mobile Lift System - MODEL #92050 Available Optional Accessories: miniLIFT MODEL #92050 & MODEL 92055 Rubber Lifting Pads SUV Conversion Set MODEL #92057 MODEL #92057 miniLIFT.LOW MODEL #92055 SCAN THIS QR CODE TO WATCH THE LIFT & MOVE miniLIFT or Go to YouTube www.youtube.com/ EquipmentSupplyCo Compact Mobile Lift with Lift & Move System! 1.800.352.9852 • info@esco.net •www.esco.
CONTACT INFO: www.esco.net - info@esco.net 15270 Flight Path Drive Brooksville, FL 34604 PH. 352.754.1117 Toll Free. 1.800.352.9852 (US, Canada Only) Fax: 352.754.4508 ESCO - The Proper Tools to Keep Your Equipment Moving! Stay Connected with ESCO...
