Owner's Manual

Troubleshooting
Trademarks Acknowledgment, Warnings, and
Regulatory Information
©2021 ESCORT Inc. ESCORT®, MAXCAM 360c®, Defender®, AutoLearn®, TrueLock™,
AutoSensitivity™, SpecDisplay™, ExpertMeter™, IVT Filter™, SmartMute™ and EZ Mag Mount™ are
trademarks of ESCORT, Inc.
Drive Smarter® is a registered trademark of Cedar Electronics Corporation.
Apple and the Apple Logo are trademarks of Apple Inc. Android, Google Play, and the Google Play Logo
are trademarks of Google Inc.
The Bluetooth® work mark and logos are registered trademarks owned by Bluetooth SIG and any use of
such marks by ESCORT Inc is under license. Sony is a trademark of Sony Corporation. Ambrella, and the
Ambrella Logo are trademarks of Ambrella, Inc. All other brands, product names and company names are
trademarks of their respective owners.
Features, Specifications and prices subject to change without notice.
FCC NOTE: Modifications not expressly approved by the manufacturer could void the user’s FCC granted
authority to operate the equipment.
FCC ID: QKLMXCAM
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
Interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Warning:
This device should be installed and operated with minimum 20 cm between the radiator and your body.
DISPOSAL OF ELECTRONICS EQUIPMENT: This product may contain hazardous substances that
could impact health and the environment if not disposed of properly.
The crossed out wheeled bin symbol indicates that the product should not be disposed of along
with household waste. It should be handed over to an applicable collection point for the recycling
of electrical equipment. By ensuring that this product is disposed of correctly you will help/prevent
potential negative impact on the environment.
If you need more information on the collection, reuse and recycling systems, please contact your local
civic office or the shop where it was originally purchased.
29 30
PROBLEM
Detector beeps briefly at the same location every
day, but no radar source is in sight.
Detector did not alert when a police car was in
view.
Detector’s audible alerts become softer after the
first few alerts.
The power-on sequence reoccurs while you are
driving.
You wish to restore the factory default settings.
The device will not turn on.
The display is blank.
SOLUTION
A motion sensor or intrusion alarm is located within
range of your route. If you have AutoLearn enabled,
the factory default setting, then MAXcam 360c will
store this signal after about 3 passes and no longer
alert to it.
Officer may not have radar or laser unit turned
on. VASCAR (Visual Average Speed Computer
and Recorder), a stopwatch method of speed
detection, may be in use.
Detector is in AutoMute mode. See “AutoMute” in
the Settings & Preferences section for details.
A loose power connection can cause MAXcam
360c to be briefly disconnected and will retrigger
the power-on sequence. Check all connections.
Press and hold the MRK and BRT buttons while
powering on the detector. A “Factory Settings
Restored” message will display, acknowledging the
reset.
Check that vehicle ignition is on.
MAXcam 360c is in Dark mode. Press the BRT
button to adjust the brightness.