Full Product Manual

Product description
Product Introduction
Long life
Its service life is significantly longer than fluorescent lamps or other old dated light sources.
Ecological
Saves electricity and low carbon.
Saves energy
Consumes less energy via use of efficient LEDs.
The Light quality
Very uniform light distribution in the complete surface.
Elegant
Modern ultra thin design, healthy light, no UV component and almost no glare.
Product Features
The most common places you are likely to find the panel lights include：Hospitals, Laboratory, Clinics,
Schools/classrooms, Conference Rooms, Offices, Restaurants, Working Stations and etc.
Applications
Attention
a. Do not allow to use scouring powder, abrasive powder, oil and acid alkaline type
detergent.
b. Do not spray air fresheners, disinfectant, cleaning organic solvents directly on
light-emitting surface.
c. Do not allow wire connectors to have contact with water.
d. Do not allow sharp objects to scratch the lamp,especially the light-emitting surface.
e.Consult a qualified electric tach or contractor to ensure work on right.
2.4G Wireless Dimming & CCT Tunable LED Panel
For the following three models of products
EEBPTL2450W-RC, EEBPTL2235W-RC, EEBPTL1435W-RC
2.4G Wireless Dimming & CCT Tunable Remote Controller
THE HANDHELD REMOTE CONTROL
Turn on
How to set the initial Remote Control code to operate the LED Panel Light(s)
How to erase the Remote Control code to set up different LED Panel Light(s)
How to Control Groups of LED Panel Lights
How to Save the default brightness level and color temp
Turn OFF the wall switch or circuit breaker. Then press and hold the ID button
until the tiny RED LED indicator is flashing on top of the Remote Control.
Then turn ON the wall switch or circuit breaker and release the ID button after
the LED Panel Light(s) flashes. Setup complete.
After enabling the initial Remote Control code to operate the LED Panel
Light(s), the remote control can be programmed to separately control up to
four LED Panel Light groups (1, 2, 3, 4) as follows: Turn OFF the wall switch
or circuit breaker for the desired Group 1. Press “1” button, Turn ON the wall
switch or circuit breaker for the desired Group 1 and release the Group “1”
button after the Group 1 LED Panel Lights flash. Group 1 programmed.
Repeat process to set up other groups.
5000K
4000K
3500K
25% brightness
Increase brightness Decrease color temperature
Increase color temperatureDecrease brightness
50% brightness
75% brightness
100% brightness
3000K
All Groups are selected
Turn off
Save
+
Press the botton simultaneously, then turn on the light, the
light flash to finish releasing the code on the lights.
+
Select the desired brightness level and color temp. Then press and hold the SAVE
button for a few seconds until the LED Panel Lights shut OFF. The settings are now
saved. Each time you turn ON the wall switch or circuit breaker, the LED Panel
Lights will utilize the saved brightness level and color temp
The Remote Control provides flexible adjustments for dimming the LED Panel
Light and selecting the desired color temp. Handheld remote control should
operate with wall main ON-OFF switch
After selecting the desired settings, push the Remote Control OFF button to
save them as default settings until the next setting change. Then the wall
main switch ON-OFF as normal operation in most time
5000K 4000K 3500K 3000K
COLOR(CCT)
BRIGHTNESS
GROUPING
Power OFF the LED Panel Light and then power it ON. The last saved brightness (which is saved by the button
“SAVE”) and the last saved color temperature (which is saved by the button “SAVE” or “OFF”) will be displayed by
default. The defau factory setting of the light is 100% brightness and 4000K.
E E Systems Group, Inc. 12346 Valley Blvd, Suite A El Monte California U.S.A. 91732
If you need to use both hand-hold controller and wall controller for the
same light, please don't use this function, directly use the following copy
function.
2.4G Wireless Dimming & CCT Tunable Remote Controller
THE WALL TYPE REMOTE CONTROLLER
Power the light off then power it on, the last saved brightness (which is saved by the button "ON") and the last saved color temperature
(which is saved by the button "ON" or "OFF") will be displayed by default. The defaulted factory setting of the light is 100% brightness and
4000K.
After 10s of each operation the controller will enter standby power saving mode. If you need to make adjustments, simply press
the "ON" button, the indicator will flash to show it is working. (If the controller is under working mode, the indicator will flash no matter
which button is pressed).
The matching method of hand-hold remote controller and wall-type remote controller, the wall controller
can copy some of the functions of the hand-hold controller by the following method.
1
2
3
4
NO Grouping Hand-hold controller Wall-type controller
5
1
2
3
4
ALL
1+ID
2+ID
3+ID
4+ID
ID
ON+CCT
ON+CCT
ON+CCT
ON+CCT
ON+CCT
A
Light code combination matching button
Brightness adjustor
Pressing the ‘ON + OFF’ buttons simultaneously will keep the remote controller’s
indicator on, turn on the light and release the buttons after the light has been on
for 2s completing the matching process. Matching code for several lights together
is available.
Press the ‘CCT’ button, the color temperature will cycle between 3000k/3500k/
4000k/5000k.After shutting down/turning off the current color temperature will
be saved.
A
+
Turn on Turn off
Wall-type remote controller cannot be used directly as a switch, it should be
used together with the switch.
Long pressing (6-9 seconds) the button "ON" until the light goes out, the current
brightness and color temperature are automatically saved. Turn off lights then turn
on, the last saved brightness and color temperature will be displayed by default.
Turn off the light to save the current color temperature then turn on the light, the
last saved color temperature will be displayed by default.
E E Systems Group, Inc. 12346 Valley Blvd, Suite A El Monte California U.S.A. 91732
The backlit LED over their complete surface brightly and highly consistent in white or warm white
(according to CCT version). They are outstandingly suited for most standard drop ceilings, also can be used as elegant
interior design elements directly on surfacing walls or hangering ceilings. Based on this panel illuminating tech, it will not
produce much heat and lower the cooling than average LED lights.The consistently illuminated surface almost has no
glare, shadows and has a highly modern appearance. The use of efficient, long-life and high quality LEDs means that
user will save outstanding electricity bill and a lot maintenance labor cost in long run.
EE Systems Group Inc. www.eleding.com , [e-mail]. 1-877-579-3889 (M-F, 10am-5pm PST), v042021
EE Systems Group Inc. www.eleding.com , [e-mail]. 1-877-579-3889 (M-F, 10am-5pm PST), v042021
EE Systems Group Inc. www.eleding.com , [e-mail]. 1-877-579-3889 (M-F, 10am-5pm PST), v042021